page 13 Install Guide 2014 Version 1.2
THE LOOK YOU LOVE
HOW TO INSTALL: DRAWER BOX BRACKETS
• When the drawer box is fixed in place - for added support you can also fix
the Drawer Box to the back wall. This can be done using the recommended
screws and/or wall plugs for your wall.
• We suggest placing these additional wall fixings at the top left and right hand
corners of the drawer box.
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
DRAWER BRACKET
SSR-2282X-AN
b
a
b
a
* Help. When the Drawer Box is in place - for added
support we recommend that you fix the Drawer Box to
the wall for additional support. This can be done using
the recommended screws and/or wall plugs for your wall.
a
4mm Allen/Hex
key required
1
DRAWER BRACKET
INSTRUCTION
TOOLS REQUIRED:
TOP TIP:
2 & 4mm Allen/Hex
3a 3b
* Fitting to the Stanchions. When attaching the brackets to the
Stanchion ensure the washer, which sits within the Stanchion
groove is rotated enough for a secure fitting (3a -3b).
• Measure down from the pencil
marks in step 2 and make a
second mark on both posts.
• Now install the upper
brackets to both posts.
• Place the carcass back
on the brackets.
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
DRAWER BRACKET
SSR-2282X-AN
* Help. When the Drawer Box is in place - for added
support we recommend that you fix the Drawer Box to
the wall for additional support. This can be done using
the recommended screws and/or wall plugs for your wall.
a
b
b
a
b
a
b
a
a
a
4mm Allen/Hex
key required
1
2
DRAWER BRACKET
INSTRUCTION
TOOLS REQUIRED:
TOP TIP:
2 & 4mm Allen/Hex
3a 3b
* Fitting to the Stanchions. When attaching the brackets to the
Stanchion ensure the washer, which sits within the Stanchion
groove is rotated enough for a secure fitting (3a -3b).
5
⁄
32
in Allen/
Hex key
required
• Place the carcass onto the
brackets and ensure its level.
• Mark a line on the posts at
the top edge of the drawer
box, on both posts.
• Place the carcass back on
the lower brackets.
• Fix screws through both
upper and lower brackets.
• Remove the carcass.
• Drill through the pilot holes
in the side of the carcass
on both sides with an
5
⁄
16
in (8mm) drill bit.
• Install the two
lower brackets
to both posts.
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
DRAWER BRACKET
SSR-2282X-AN
* Help. When the Drawer Box is in place - for added
support we recommend that you fix the Drawer Box to
the wall for additional support. This can be done using
the recommended screws and/or wall plugs for your wall.
a
4mm Allen/Hex
key required
1
b
a
2a
2
DRAWER BRACKET
INSTRUCTION
TOOLS REQUIRED:
TOP TIP:
2 & 4mm Allen/Hex
3a 3b
* Fitting to the Stanchions. When attaching the brackets to the
Stanchion ensure the washer, which sits within the Stanchion
groove is rotated enough for a secure fitting (3a -3b).
29
⁄
16
in
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
Home Décor Innovations
www.hdhc.com
V2_HD 11.12
DRAWER BRACKET
SSR-2282X-AN
b
a
b
a
* Help. When the Drawer Box is in place - for added
support we recommend that you fix the Drawer Box to
the wall for additional support. This can be done using
the recommended screws and/or wall plugs for your wall.
a
4mm Allen/Hex
key required
1
a
a
DRAWER BRACKET
INSTRUCTION
TOOLS REQUIRED:
TOP TIP:
2 & 4mm Allen/Hex
3a 3b
* Fitting to the Stanchions. When attaching the brackets to the
Stanchion ensure the washer, which sits within the Stanchion
groove is rotated enough for a secure fitting (3a -3b).
*Note: leave about a
13
⁄
64
in gap
between the wall and the back of
the carcass.
14
Evolution_Elite_Relax
Coperture montante
La copertura montante può essere inserita
su tutti i lati del montante ed è facilmente
accorciabile a misura con un seghetto per
metallo.
Oltre che svolgere una funzione estetica,
la copertura, ha la funzione di copri-fili.
La copertura si incastra a pressione.
Morsetto sostegno ripiano
SSE-2263
Il morsetto può essere fissato
indifferentemente su tutti i lati del
montante a qualsiasi altezza.
Il fissaggio avviene tramite l'avvitamento
di una brugola che, facendo ruotare una
piastrina, incastra il morsetto al montante
(vedi fig.1)
L’apertura della morsa è regolabile
attraverso la brugola posta nella parte
inferiore del morsetto.
L’apertura va da 0 a 30 mm.
I gommini neri posti all’interno della
morsa del morsetto possono essere tolti
a piacimento.
(fig.1)
Bordatura per ripiano
SSE-2025-AN
Il ripiano può essere fissato mediante
l’utilizzo di bordature in alluminio.
Dopo avere fissato il morsetto sostegno
ripiani (SSR-1928)
al montante, aprite la morsa in modo
tale da stringere la bordatura
e appoggiatevi sopra il ripiano.
La bordatura porta ripiani fino
a 30 mm di spessore e può essere
facilmente ridotta in lunghezza grazie
ai tappi asportabili.
La bordatura aumenta la portata del
ripiano da 20 a 25 kg.
Attenzione: l’uso delle bordature
aumenta di 26 mm l’ingombro
in larghezza del ripiano: tenerne conto
in fase di progettazione.
2X
2X
Upper Drawer Bracket
(Sold in pairs)
Lower Drawer Bracket
INFORMATION
30/66lbs
(inl.Drawer Box)
MAX
25kg
(55lbs)
MAX
150kg
(330lbs)
MAX
15kg
(33lbs)
MAX
8kg
(17.5lbs)
MAX
70kg
(160lbs)
MAX