Bushnell Trophy Cam 119445 Manuale utente

TROPHY CAM

™

I N STRUCTION MANUA L

Model#s: 119435 / 119445 / 119455

Lit# 98-1517 / 1-10

2

3

TABLE OF CONTENTS PAGE #

ENGLISH

FrANçAIS

ESPAñOL

DEuTSCH

ITALIANO

POrTuGuêS

5-31

32-64

65-97

98-133

134-166

167-199

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail cameras

on the market! Bushnell is very proud of this little unit and we

are sure you will be pleased with it as well. We appreciate your

business and want to earn your trust. Please refer to the notes

below and the instructions in this manual to ensure that you are

completely satisﬁed with this product.

If your Bushnell Trophy Cam does not seem to be

functioning properly or if you are having photo/video quality

issues, please check the Troubleshooting/FAQ section

on pages 25-28.

Problems are often due to something simple that was

overlooked, or require only changing one setting to solve.

If your problem continues after trying the solutions in

the Troubleshooting/FAQ section, please call Bushnell

Customer Service at (800) 423-3537. In Canada, call (800)

361-5702.

Bushnell recommends using 8 Energizer

®

Lithium AA batteries in

all Trophy Cams to obtain maximum battery life

Bushnell recommends using SanDisk

®

SD and SDHC Cards

(up to 16GB capacity) in all Trophy Cams

5

INTRODUCTION

About the Trophy Cam

The Bushnell Trophy Cam is a digital scouting camera. It can be triggered

by any movement of game in a location, detected by a highly sensitive

Passive Infra-Red (PIR) motion sensor, and then take high quality pictures

(up to 8MP still photos), or video clips.

The Trophy Cam consumes very little power (less than 300μA) in a stand-

by (surveillance) state. This means it can deliver up to six months stand-by

operation time when the device is powered by eight AA alkaline batteries,

and up to twelve months utilizing lithium AA batteries. Once motion in the

monitored area is detected, the digital camera unit will be triggered at once

(typically within one second) and then automatically take photos or videos

according to previously programmed settings. The Trophy Cam is equipped

with built-in infrared LEDs that function as a ﬂash, so that it delivers clear

photos or videos (in black & white) even in the dark, and it can take color

photos or videos under sufﬁcient daylight. The Trophy Cam is designed for

outdoor use and is resistant against water and snow.

Applications

The Trophy Cam can be used as a trail camera for hunting or scouting

game. It is also suitable for surveillance usage.

PARTS AND CONTROLS

The Trophy Cam provides the following connections for external devices:

USB port, SD card slot, TV Out, and external DC power in (Fig. 1).

A 3-way power switch is used to select the main operating modes: OFF,

SETUP, and ON (Fig. 2).

A control key interface with six keys is primarily used in SETUP mode to

select operational functions and parameters. As shown in Fig. 2, these keys

are: UP, DOWN, LEFT, RIGHT, OK and MENU. Four of the keys can also

perform a second function (shortcut operations in SETUP mode) in addition

ENGLISH

6

to their main function: The DOWN key can be used to set the camera to

Photo mode (still camera icon), and the UP key can set the camera to Video

mode (movie camera icon). The RIGHT key also serves as the manual shutter

(“SHOT”) button of the camera and the OK key switches the camera to

the Playback (“REPLAY”) mode. These secondary functions are indicated by

icons or text above the key as shown in Fig. 2.

Fig. 2: Button and

Switch Guide

Fig. 1: Connections

TV Out

USB Port

SD Card Slot

DC In

ON

SETUP

OFF

LED IR Flash

Motion/ Low Battery Indicator

Lens

Lock Hole

PIR Sensor

FRONT VIEW

LCD Screen

Power/Mode

Switch

UP/Video

DOWN/Photo

LEFT

MENU

OK/Replay

RIGHT/Shot

Cable to Battery

Compartment

7

INSTALLING THE BATTERIES AND SD CARD

Before you begin learning how to use your Trophy Cam, you will ﬁrst need

to install a set of batteries and insert an SD card. Although that may only take

you a minute, there are some important notes about both batteries and SD

cards you should be aware of, so please take the time to read the following

directions and cautions:

Loading Batteries

After opening the two latches on the right side

of the Trophy Cam, you will see that the Trophy

Cam has eight battery slots. Starting at the top

of the battery compartment, slots 1, 2, 3 and 4

form one group, while slots 5, 6, 7 and 8 form

the other group, each providing 6 volts in parallel.

For maximum battery life, you should install a full

set of eight batteries. The Trophy Cam may also

be operated by just four batteries installed in

the top group only (see right), starting at slot 1.

Battery life will be shorter with 4 batteries, but

the camera will operate normally. Whether you use 4 or 8, be sure to insert

each battery with correct polarity (negative or “ﬂat” end against the long

spring of each battery slot).

Bushnell recommends using eight new lithium AA (Energizer® brand) or

alkaline AA batteries. NiMh Rechargeable batteries can also be used, but

they might have a shorter life span due to their reduced efﬁciency over time

and at low temperature. It is also possible to use a lead-acid external battery cell

with 6V output or suitable AC adapter-see below for more details.

Using an External Power Source

(optional, user provided)

Optionally, you can connect an external 6V DC power source to the “DC In”

jack at the bottom of the Trophy Cam. It is recommended to use a power

source with a current output greater than 1000mA. However, during bright

daytime operation when no ﬂash is required, the Trophy Cam can function

with much less current (>400mA). Please use a compatible power source

8

cable (not provided) to connect the external DC power source with the power

input jack of the Trophy Cam, making sure that the polarity is correct. Note:

The power connector is a 4.0x1.7mm coaxial DC power plug with positive

“tip” (inside pin) polarity (Radio Shack P/N 274-1532 or equivalent).

If both an external power source is connected and batteries are installed, the

Trophy Cam will be powered by the external power source.

When the batteries become weak, the low-battery indicator LED will glow

blue, indicating the batteries should be changed (pg 6, “Front View”).

Inserting the SD Card

The Trophy Cams have 32MB internal memory, which can hold only about

20 photos (@ 5MP resolution). This is handy for testing and getting familiar

with the camera, but you will no doubt want to leave the camera unattended

for longer than a day, so using an SD card is recommended. Insert the SD

card (with the camera’s power switch in the OFF position) before beginning

to operate the camera. Don’t insert or remove the SD card when the power

switch is in the ON position.

The Trophy Cam uses a standard SD (Secure Digital) memory card to save

photos (in .jpg format) and/or videos (in .asf format). SD and SDHC (High

Capacity) cards up to a maximum 16GB capacity are supported. Before

inserting the SD card into the card slot after opening the camera’s front

cover, please make sure that the write-protect

switch on the side of the card is “off” (NOT in the

“Lock” position). The following describes how to

insert and remove the SD card:

• Insert the SD card into the card slot with its

label side upwards (see above). A “click” sound

indicates that the card is installed successfully. If the wrong side of the

card is facing up, you will not be able to insert it without force-there is only

one correct way to insert cards. If the SD card is not installed correctly,

the device will not display an SD card icon on the LCD in SETUP mode

(the SD card icon displayed after switching to SETUP mode will have a “lock”

symbol inside it in it if the card is locked). Formatting the SD card by using

the Trophy Cam’s “Format” parameter before using it for the ﬁrst time is

recommended, especially when a card has been used in other devices

9

(see “Changing Menu Parameter Settings” for details).

• To take out the SD card, just gently push in the card (do not try to pull it

out without pushing in ﬁrst). The card is released from the slot and ready

to be removed when you hear the click.

USING THE TROPHY CAM

Once you’ve prepared your Trophy Cam by properly installing batteries and

an SD card, you could simply take it outside, strap it to a tree, switch it on

and leave-and you might get some great photos that are exactly what you

wanted. However, we highly recommend that you ﬁrst spend some additional

time indoors with this manual and your camera until you know a bit more

about what the 3-way switch and those control keys do. If nothing else, you’ll

probably want to at least set the date and time so the camera will imprint

them (or not-it’s your option) on your photos as they are taken, learn how to

set the camera to shoot video clips instead of still photos if you like, and read

some tips about mounting it on a tree.

THE OFF, ON, AND SETUP MODES

The Trophy Cam has three basic operational modes:

• OFF mode: Power switch in the OFF position.

• ON mode: Power switch in the ON position (LCD screen is off.)

• SETUP mode: Power switch at SETUP position (LCD screen is on).

OFF Mode

The OFF mode is the “safe” mode when any actions must be taken, e.g.,

replacing the SD card or batteries, or transporting the device. You will also

WARNING

Be sure the camera’s power is switched OFF

before inserting or removing SD cards or batteries.

10

use OFF mode if you connect the camera to a computer’s USB port later

to download your photos/videos. And of course, when you are storing or not

using the camera, you will switch it to OFF. Please note that even in the OFF

mode the Trophy Cam still consumes power at a very low level. Therefore,

it’s a good idea to take the batteries out of the battery compartment if the

camera will not be used for a long time.

ON Mode

Anytime after the batteries and SD card have been inserted, you can switch

on the camera. When the power switch is moved to the top position, the

camera will enter into the ON (Live) mode. The motion indicator LED (pg. 5,

“Front View”) will blink red for about 10 seconds. This interval allows time for

you to close the Trophy Cam’s front cover, lock it, and leave the monitored

area. Once in the ON mode, no manual controls are needed or possible

(the control keys have no effect). The Trophy Cam will take photos or

videos automatically (according to its current parameter settings) when it is

triggered by the PIR sensor’s detection of activity in the area it covers.

You can either move the power switch directly from OFF to ON mode, or

stop at the SETUP position ﬁrst to change one or more settings, then move

the switch to ON after you have ﬁnished doing so.

SETUP Mode

In the SETUP mode you can check and change the settings of the Trophy

Cam with the help of its built-in LCD (or a monitor connected to the TV out

jack). These settings, found in the SETUP Menu, let you change the photo

or video resolution, interval between photos, switch the time imprint on, etc.

Moving the power switch to the SETUP position will turn on the LCD display,

and you will see an information screen that shows how many images have

been taken, the battery level, camera or video mode, etc (see Fig. 3 below).

NOTE: always move the power switch from OFF to SETUP mode. It

is possible that the camera could lockup if it is switched from ON to

SETUP mode. If this occurs, simply move the switch to OFF and then

push it up to SETUP again.

11

SETUP Mode Shortcut Keys/Functions

As mentioned earlier in “Parts & Controls”, four of the keys below the LCD

have secondary, “shortcut” functions when the camera is switched to

SETUP mode (but the MENU key has not been pressed):

• Press the UP key to quickly set the camera to shoot video clips.

• Press the DOWN key to quickly set the camera to take still photos.

• Press the RIGHT key to manually trigger the shutter. This is useful

for testing the camera-make sure you are in SETUP mode, press the

RIGHT key, and a few seconds later a photo or video (depending on

how the camera was set) will be saved to the SD card (or internal

memory if no card is inserted). The “number of images taken” counter

on the bottom left of the LCD will increase by one. If the display

indicates “SD PROTECTED” when you press the SHOT key, switch

the camera OFF, remove the SD card and slide its protect switch off.

• Press the OK key to replay (review or playback) photos/videos on

the LCD (color viewer models only), or a connected TV monitor (std.

display models). See “Playing Back Photos/Videos” for more details.

Fig. 3: SETUP Information Screen (standard display model shown)

Camera Mode

Time Stamp

Number of Images

Available Space

Date:Month-Day-Year

TV Status

Battery Level

SD Card Status

Image Size

Time

Hour:Minute:Second

12

Using the SETUP Menu to Change Settings

The main purpose of the SETUP mode is to allow you to change the settings

of the camera’s parameters (12-13 different ones are available) so your

Trophy Cam operates exactly the way you want it to. You will do this by

entering the SETUP Menu and pressing the keys below the LCD display,

which will show you each parameter and its setting.

Changing Parameter Settings in SETUP Mode

A wide range of options or “parameters” are provided to allow you to set

the Trophy Cam to your operational preferences. To change the setting of

any parameter you must ﬁrst switch to the SETUP mode. Once in SETUP

mode, pressing the MENU button will allow you to select any parameter and

change its setting. The name of the parameter and its current setting will be

shown on the LCD. Pressing the RIGHT or LEFT key scrolls to the next or

previous parameter (RIGHT key to move on to the next parameter and LEFT

key to go back to the previous parameter), and pressing the UP or DOWN

key lets you select a different setting for the currently displayed parameter.

Once you have selected your preferred new setting for a parameter, press

the OK button to save the new setting (actually change it). When have are

ﬁnished changing the settings of one or more parameters, press MENU

again to exit the SETUP menu. MENU can also be pressed anytime you

want to cancel changing a parameter’s setting after a new setting has been

selected (but OK has not been pressed yet). After setting the parameters

to your preferences, be sure to move the switch to ON to begin actually

taking photos or videos. No images will be captured if the switch is left in the

SETUP position (unless you press the RIGHT/Shot key after exiting the menu)-

in fact, the camera will power off automatically after a few seconds with no

key pressed.

Color Viewer vs. Standard Display Models

There is a slight difference in how the settings for a parameter are shown

between the two different types of Trophy Cam models:

• On models with a color viewer, all the available settings for the currently

displayed parameter are shown on one screen, with a checkmark next

13

COLOR VIEWER

(4a)

(4b)

(4c)

Fig. 4: Selecting Parameter Settings

to the current setting (Fig. 4a). To change the setting, ﬁrst use the UP/

DOWN keys to highlight (select) the new setting you want (Fig. 4b), then

press OK to “Execute” the actual change to the selected setting. The

checkmark will appear next to your new setting to conﬁrm this (Fig. 4c).

• On models with standard (non-color) display, only one setting is displayed

at a time, starting with the current setting for the parameter when it is

ﬁrst selected (Fig. 4d). To change the setting, use the UP/DOWN keys

to display the new setting you want (Fig. 4e), then press OK to “Execute”

(make the actual change to this setting). If you want to conﬁrm this setting

is now the current one, just press the RIGHT key to scroll to the next

parameter, then press LEFT to go back again to the previous one. You

should see the parameter setting you just made.

STANDARD DISPLAY

(4d)

(4e)

Press MENU

Press DOWN

Press OK

14

EXAMPLES-Changing the Settings of Some Common Parameters

Following this page, you will ﬁnd tables listing all of the parameters found in

the SETUP Menu, along with their possible settings (or range of settings),

and a detailed description of what the parameter controls and what

the settings do. If you read the previous section detailing how to select

parameters and change their settings, you should be able to dive right in, ﬁnd

the parameter(s) you want, and setup the camera to your preferences. But

maybe you’d rather walk through an example or two ﬁrst:

To change any parameter’s setting, always start with the power switch in the

SETUP position. After the LCD comes on, press the MENU key.

The ﬁrst parameter you will when you ﬁrst enter the SETUP Menu is “Mode”.

To change it from its default setting of “Camera” (still photos) to “Video”

(shoot video clips), press the DOWN key to highlight “Video” (color viewer

models) or to select the “Video” setting (std. display models). Press the OK

key to “Execute” (Set) the new setting you’ve selected for this parameter.

Now press the RIGHT key to move to another parameter in the Menu.

Pressing it four times will take you to “Video Length”. Try using the UP and

DOWN keys to scroll through the range of settings, then press OK to lock in

your setting for the length of each video clip the camera shoots.

Pressing the RIGHT key several more times will get you to the “Default Set”

parameter. Highlight or select “Execute” (using UP or DOWN) and press OK

to restore all parameters (including the Mode and Video Length parameters

you changed a minute ago) back to their original factory default settings. The

default settings for each parameter are indicated in bold type in the SETUP

Menu tables on the next several pages.

Be sure to set the current date and time, using the “Set Clock” parameter,

if you choose to change the “Time Stamp” parameter setting to “On” since

that will tell the camera to imprint the date and time on each of the images

it captures.

15

Parameter

Settings

(Bold=default)

Description

Mode

Camera or

Video

Selects whether still photos or

video clips are captured when the

camera is triggered.

Image Size

(only aects

still photos)

5M Pixel, 8M

Pixel, 3M Pixel

Selects resolution for still photos

from 3 to 8 megapixels. Higher

resolution produces better quality

photos, but creates larger ﬁles

that take up more of the SD card

capacity (ﬁlls up faster). 5M is a

good compromise between quality

and ﬁle size.

Capture

Number

(only aects

still photos)

1 Photo, 2

Photo, 3 Photo

Selects how many photos are

taken in sequence per trigger in

Camera mode. Please also refer to

the Interval parameter.

Video Size

(only aects

video clips)

640x480,

720x480,

320x240

Selects video resolution (in pixels

per frame). Higher resolution

produces better quality videos, but

creates larger ﬁles that take up

more of the SD card capacity (ﬁlls

up faster). 640x480 is VGA video

in standard 4:3 format, 720x480 is

widescreen format.

Video

Length (only

aects video

clips)

10S (second)

default, with

60S to1S

possible range

Sets length per captured video

clip. Settings begin with 10 second

default when parameter is ﬁrst

selected. After stepping down to

1S, video length settings start over

at 60S.

The SETUP Menu – Parameters and Settings List w/Descriptions

16

Parameter

Settings

(Bold=default)

Description

Interval

10S (second)

default,

with a 60M

(minute) to1S

(second) range

of settings

available.

(60M-1M are set

in one minute

increments,

59S-1S are set

in one second

increments)

Selects the length of time that the

camera will “wait” until it responds

to any additional triggers from the

PIR after an animal is ﬁrst detected

and remains within the sensor’s

range. During this user set “ignore

triggers” interval, the camera will

not capture photos/videos. This

prevents the card from ﬁlling up

with too many redundant images.

Settings begin with 10 second

default when parameter is ﬁrst

selected. Note: after setting down

past “1S”, settings start over at “60M”.

Sensor

Level

Normal, High,

Low

Selects the sensitivity of the PIR

sensor. The “High” setting will

make the camera more sensitive

to infrared (heat) and more easily

triggered by motion, and the “Low”

setting makes it less sensitive to

heat and motion. The High setting

can be useful when the ambient

temperature is warm (making it

more difﬁcult for the sensor to

detect animals), and the Low

setting may help in cold weather if

the camera is being triggered too

often by anything warmer than the

surroundings.

17

Parameter

Settings

(Bold=default)

Description

Format Execute

(followed by an

additional No/

Yes step on color

viewer models

only)

Deletes (erases) all ﬁles stored

on a card to prepare it for reuse.

Always format a card that has been

previously used in other devices.

Caution! Make sure you have

downloaded and backed up any

ﬁles you want to preserve ﬁrst!

Press OK to execute (then select Yes

and press OK again on color viewer

models), press MENU (or select

NO then press OK) to exit without

formatting.

TV Out

NTSC, PAL

Selects video standard /format for

the “TV Out” output jack. The video

standard is NTSC for the United

States, Canada, Mexico, Asia and

South America. PAL is used primar-

ily in Europe.

Time Stamp

(only aects

still photos)

Off, On

Select “On” if you want the date &

time (that the photo was captured)

imprinted on every photo, select

“Off” for no imprint.

Set Clock Set

Press OK and use the UP/DOWN

keys (to change the setting) and

LEFT/RIGHT keys ( to move

to the next ﬁeld) to set the hour

(24-hr format only, “00”=midnight,

“12”=noon) and minute, and then

(on the lower row), the year, month

and date.

18

Parameter

Settings

(Bold=default)

Description

Default Set

Cancel,

Execute

Select “Execute” and press OK

to restore all parameters to the

original factory default settings. If

the camera is behaving oddly and

you think you may have changed

the setting for something accidently

(but aren’t sure which one), this

will reset all parameters to their

most commonly used or “generic”

settings.

19

Fig. 5: Attaching the Belt

MOUNTING AND POSITIONING THE TROPHY CAM

Mounting

After you’ve set up the camera’s parameters to your personal preferences

at home or in your truck, you’re ready to take it outside and slide the power

switch to “ON”. When setting up the Trophy Cam for scouting game or

other outdoor applications, you must be sure to mount it in place correctly

and securely. We recommend mounting the Trophy Cam on a sturdy tree

with a diameter of about 6 in. (15cm). To get the optimal picture quality,

the tree should be about 16-17 ft. (5 meters) away from the place to be

monitored, with the camera placed at a height of 5-6.5 ft. (1.5~2 m). Also,

keep in mind that you will get the best results at night when the subject is

within the ideal ﬂash range, no farther than 45’ (14m) and no closer than 10’

(3m) from the camera.

There are two ways to mount the Trophy Cam: using the provided adjustable

web belt, or the tripod socket.

Using the adjustable web belt: Fig. 5 illustrates using the web belt on

the Trophy Cam. Push one end of the belt through the two brackets on

the back of the Trophy Cam. Thread one plastic buckle part onto each

end of the belt. Fasten the belt securely around the tree trunk by clicking

the buckle ends together after tightening the belt so there is no slack left.

20

Using the tripod socket: The camera is equipped with a socket at the

bottom end to enable mounting on a tripod or other mounting accessories

with a standard1/4-20 thread.

Two optional mounting accessories, a “Bear Safe” metal camera box

(model # 19653C) and Deluxe Tree Bracket (model# 119652C) are also

available-please see your Bushnell dealer or website for more details.

Sensing Angle and Distance Test

To test whether the Trophy Cam can effectively monitor the area you

choose, this test is recommended to check the sensing angle and monitoring

distance of the Trophy Cam. To perform the test:

• Switch the Trophy Cam to the SETUP mode.

• Make movements in front of the camera at several positions within

the area where you expect the game or subjects to be. Try different

distances and angles from the camera.

• If the motion indicator LED light blinks, it indicates that position can be

sensed. If it does not blink, that position is outside of the sensing area.

The results of your testing will help you ﬁnd the best placement when

mounting and aiming the Trophy Cam. The height away from the ground for

placing the device should vary with the animal size appropriately. In general,

3 to 6 feet is preferred.

You can avoid potential false triggers due to temperature and motion

disturbances in front of the camera by not aiming it at a heat source or nearby

tree branches or brush (especially on windy days).

Switching ON the Camera

Once you switch to the ON mode, the motion indicator LED (red) will blink

for about 10 seconds. This gives you time to close and lock the front cover of

the Trophy Cam and then walk away. During this time, the motion indicator

LED will blink red continuously. After it stops blinking, the PIR is active, and

any motion that is detected by it will trigger the capture of photos or videos

as programmed in the SETUP Menu. Be sure you have read the descriptions

of the Capture Number, Video Length, Interval and Sensor Level parameters.

La pagina sta caricando ...

Bushnell Trophy Cam 119445 Manuale utente

Questo manuale è adatto anche per

Bushnell Trophy Cam 119445 Manuale utente

in altre lingue

Documenti correlati

Altri documenti