Stanley FATMAX SFMCST933 Manuale del proprietario

SFMCST933

Final page size: A5 (148mm x 210mm)

www.stanleytools.eu

B

Copyright STANLEYFATMAX

English (original instructions) 4

Deutsch (übersetzt von den originalanweisungen) 15

Français (traduction de la notice d’instructions originale) 27

Italiano (tradotto dalle istruzioni originali) 39

Nederlands (vertaald vanuit de originele instructies) 51

Español (traducido de las instrucciones originales) 63

Português (traduzido das instruções originais) 75

Svenska (översatt från de ursprungliga instruktionerna) 87

Norsk (oversatt fra de originale instruksjonene) 98

Dansk (oversat fra original brugsvejledning) 108

Suomi (käännetty alkuperäisestä käyttöohjeesta) 119

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 130

1

Fig.A

Fig.B

Fig.C

13

12

11

9

14

10

8

7

6

5

3

2

1

4

15

11

16

8

2

Fig.D

15

5

Fig.E

6

Fig.F

14

13

Fig.G

5

4

Fig.H Fig.I

Minimum

610 mm

25

3

Fig.J

7

Fig.K

19

18

10

Fig.L

20

22

21

23

24

Fig.N

4

ENGLISH

Battery

Cat #

Output

Voltage

Charger

SFMCB12

SFMCB202 18 X

SFMCB204 18 X

SFMCB206 18 X

“X” Indicates that the battery pack is compatible with that

specific charger. Read the instruction manual for more

specificinformation.

EC-Declaration of Conformity

Machinery Directive

Grass Trimmer

SFMCST933

STANLEYFATMAX declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60335-1:2012 + A11:2014, EN50636-2-91:2014.

2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VI

DEKRA Certification B.V.

Meander 1051 / P.O. box 5185

6525 MJ ARNHEM / 6802 ED

ARNHEM, Netherlands

Notified Body ID No.: 0344

Level of accoustic power according to 2000/14/EC

(Article 12, Annex III, L ≤ 50 cm):

L

PA

(measured sound pressure level) 81 dB(A)

uncertainty (K) = 1.8 dB (A)

L

WA

(guaranteed sound power) 96 dB(A)

These products also comply with Directive 2014/30/EU

and 2011/65/EU. For more information, please contact

STANLEYFATMAX at the following address or refer to the back

of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf ofSTANLEYFATMAX.

A. P. Smith

Technical Director

STANLEYFATMAX Europe, Egide Walschaertsstraat14-18,

2800 Mechelen, Belgium

14.08.2019

Congratulations!

You have chosen a STANLEYFATMAX tool. Years of experience,

thorough product development and innovation make

STANLEYFATMAX one of the most reliable partners for

professional power toolusers.

Technical Data

SFMCST933

Voltage V

DC

18

UK & Ireland V

DC

18

Type 1

RPM /min 5500-7200

Cutting Swath Size mm 330

Weight (without battery pack) kg 2.4

Noise values and vibration values (triax vector sum). Grass Trimmer mode

according to EN50636-2-91:

L

PA

(emission sound pressure

level)

dB(A) 81.0

L

WA

(sound power level) dB(A) 94

K (uncertainty for the given

sound level)

dB(A) 1.8

Vibration emission value a

h

= m/s

2

3.1

Uncertainty K = m/s

2

1.5

The vibration emission level given in this information sheet has

been measured in accordance with a standardised test given in

EN50636 and may be used to compare one tool with another. It

may be used for a preliminary assessment ofexposure.



WARNING: The declared vibration emission

level represents the main applications of the tool. However

if the tool is used for different applications, with different

accessories or poorly maintained, the vibration emission

may differ. This may significantly increase the exposure

level over the total workingperiod.

An estimation of the level of exposure to vibration should

also take into account the times when the tool is switched

off or when it is running but not actually doing the job.

This may significantly reduce the exposure level over the

total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation of

workpatterns.

English (original instructions)

GRASS TRIMMER

SFMCST933

Batteries

Chargers/Charge Times (Minutes)

Cat #

DC

Weight

5

ENGLISH

WARNING: To reduce the risk of injury, read

the instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death or

seriousinjury.



CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

SAFETY INSTRUCTIONS



WARNING: When using mains-powered

appliances, basic safety precautions, including the

following, should always be followed to reduce the risk of

fire, electric shock, personal injury and materialdamage.



WARNING: When using the machine the

safety rules must be followed. For your own safety and

bystanders please read these instructions before operating

the machine. Please keep the instructions safe for lateruse.

• Read all of this manual carefully before operating theappliance.

• The intended use is described in this manual. The use of any

accessory or attachment or the performance of any operation

with this appliance other than those recommended in this

instruction manual may present a risk of personalinjury.

• Retain this manual for futurereference.

IMPORTANT

READ CAREFULLY BEFORE USE

KEEP FOR FUTURE REFERENCE

SAFE OPERATING PRACTICES

Training

a ) Read the instructions carefully. Be familiar with the

controls and the correct use of themachine.

b ) Never allow children or people unfamiliar with these

instructions to use the machine. Local regulations can

restrict the age of theoperator.

c ) Keep in mind that the operator or user is responsible

for accidents or hazards occurring to other people or

theirproperty.

Preparation

a ) Before use, always visually inspect the machine for

damaged, missing or misplaced guards orshields.

b ) Never operate the machine while people, especially

children, or pets are nearby.

Operation

a ) Wear eye protection and stout shoes at all times while

operating themachine.

b ) Avoid using the machine in bad weather conditions

especially when there is a risk oflightning.

c ) Use the machine only in daylight or good artificiallight.

d ) Never operate the machine with damaged guards or

shields or without guards or shields inplace.

e ) Switch on the motor only when the hands and feet are

away from the cuttingmeans.

f ) Always disconnect the machine from the power

supply (i.e. remove the plug from the mains, remove the

disabling device or removable battery)

• whenever the machine is left unattended;

• before clearing a blockage;

• before checking, cleaning or working on the machine;

• after striking a foreign object;

• whenever the machine starts vibratingabnormally.

g ) Take care against injury to feet and hands from the

cuttingmeans.

h ) Always ensure that the ventilation openings are kept clear

ofdebris.

i ) Remove any objects that may cause kickback, such as

branches androcks.

j ) Check for loose fasteners and damaged parts, such as cracks in

the cuttingattachment.

Maintenance and Storage

a ) Disconnect the machine from the power supply

(i.e. remove the plug from the mains, remove the

disabling device or removable battery) before carrying out

maintenance or cleaningwork.

b ) Use only the manufacturer’s recommended replacement

parts andaccessories.

c ) Inspect and maintain the machine regularly. Have the

machine repaired only by an authorizedrepairer.

6

ENGLISH

d ) When not in use, store the machine out of the reach

ofchildren.

e ) Use blade cover for metal blades during transport

andstorage.

f ) Clean before storing, including the use of guards on

cutting attachments with metalblades.

ADDITIONAL SAFETY INSTRUCTIONS FOR

GRASS TRIMMERS



WARNING: Cutting elements continue to

rotate after the motor is switchedoff.

• Wear long trousers to protect yourlegs.

• Before using the appliance, check that your cutting path is free

from sticks, stones, wire and any otherobstacles.

• Only use the appliance in the upright position, with the cutting

line near the ground. Never switch the appliance on in any

otherposition.

• Move slowly when using the appliance. Be aware that freshly

cut grass is damp andslippery.

• Do not work on steep slopes. Work across the face of slopes,

not up anddown.

• Never cross gravel paths or roads while the appliance

isrunning.

• Never touch the cutting line while the appliance isrunning.

• Do not put the appliance down until the cutting line has come

to a completestandstill.

• Use only the appropriate type of cutting line. Never use metal

cutting line or fishingline.

• Keep hands and feet away from the cutting line and blade at

all times, especially when switching on themotor.

• Before using the appliance and after any impact, check for

signs of wear or damage and repair asnecessary.

• Take care against injury from any device fitted for trimming

the filament line length. After extending new cutter line always

return the machine to its normal operating position before

switchingon.

• Close supervision is necessary when the appliance is used

nearchildren.

• This appliance is not intended for use by young or infirm

persons withoutsupervision.

• This appliance is not to be used as atoy.

• Use in a dry location only. Do not allow the appliance to

becomewet.

• Do not immerse the appliance inwater.

• Do not open the body casing. There are not user-serviceable

parts inside

• Do not operate the appliance in explosive atmospheres, such

as in the presence of flammable liquids, gases ordust.

• When the appliance is stored or transported in a vehicle

it should be placed in the boot or restrained to prevent

movement following sudden changes in speed ordirection.

• When not in use, the appliance should be stored in a dry, well

ventilated place out of reach ofchildren.

• Children should not have access to storedappliances.

Safety of Others

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance

by a person responsible for theirsafety.

• Children must be supervised to ensure that they do not play

with theappliance.

Residual Risks

To ensure you have good footing on slopes, do not overreach.

Keep your balance at all times. Always walk, do notrun.

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These risks

can arise from misuse, prolonged useetc.

Even with the application of the relevant safety regulations and

the implementation of safety devices, certain residual risks can

not be avoided. These include:

• Injuries caused by touching any rotating/movingparts.

• Injuries caused when changing any parts, blades

oraccessories.

• Injuries caused by prolonged use of a tool. When using any

tool for prolonged periods ensure you take regularbreaks.

• Impairment ofhearing.

• Health hazards caused by breathing dust developed when

using your tool (example: working with wood, especially oak,

beech and MDF.)

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your STANLEYFATMAX charger is double insulated

in accordance with EN60335; therefore no earth wire

isrequired.



WARNING: 115 V units have to be operated

via a fail-safe isolating transformer with an earth screen

between the primary and secondary winding.

If the supply cord is damaged, it must be replaced by a specially

prepared cord available through the STANLEYFATMAX

serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.

7

ENGLISH



WARNING: No connection is to be made to

the earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A..

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

2

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

Chargers

STANLEYFATMAX chargers require no adjustment and are

designed to be as easy as possible tooperate.

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any

liquid to get inside charger. Electric shock mayresult.



WARNING: We recommend the use of a

residual current device with a residual current rating of

30mA orless.



CAUTION: Burn hazard. To reduce the risk

of injury, charge only STANLEYFATMAX rechargeable

batteries. Other types of batteries may burst causing

personal injury anddamage.



CAUTION: Children should be supervised to

ensure that they do not play with theappliance.

NOTICE: Under certain conditions, with the

charger plugged into the power supply, the exposed

charging contacts inside the charger can be shorted by

foreign material. Foreign materials of a conductive nature

such as, but not limited to, steel wool, aluminum foil or

any buildup of metallic particles should be kept away

from charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other

than charging STANLEYFATMAX rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must be

replaced immediately by the manufacturer, its service agent or

similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig.B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

7

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The battery pack is fully charged

and may be used at this time or left in the charger. To

remove the battery pack from the charger, push the battery

release button

8

on the batterypack.

NOTE:To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

8

ENGLISH

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the

charger from the AC outlet before cleaning. Dirt and

grease may be removed from the exterior of the charger

using a cloth or soft non-metallic brush. Do not use water

or any cleaning solutions. Never let any liquid get inside

the tool; never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All Battery

Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in STANLEYFATMAXchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may

be flammable if exposed to spark orflame.



WARNING: Never attempt to open the

battery pack for any reason. If battery pack case is cracked

or damaged, do not insert into charger. Do not crush,

drop or damage battery pack. Do not use a battery pack

or charger that has received a sharp blow, been dropped,

run over or damaged in any way (i.e., pierced with a

nail, hit with a hammer, stepped on). Electric shock or

electrocution may result. Damaged battery packs should

be returned to service centre forrecycling.



WARNING: Fire hazard. Do not store or

carry the battery pack so that metal objects can

contact exposed battery terminals. For example, do

9

ENGLISH

not place the battery pack in aprons, pockets, tool boxes,

product kit boxes, drawers, etc., with loose nails, screws,

keys,etc.



CAUTION: When not in use, place tool on

its side on a stable surface where it will not cause a

tripping or falling hazard. Some tools with large battery

packs will stand upright on the battery pack but may be

easily knockedover.

Transportation



WARNING: Fire hazard. Transporting

batteries can possibly cause fire if the battery terminals

inadvertently come in contact with conductive materials.

When transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a shortcircuit.

STANLEYFATMAX batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a STANLEYFATMAX battery pack

will be excepted from being classified as a fully regulated Class

9 Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class

9. All lithium-ion batteries have the Watt Hour rating marked

on the pack. Furthermore, due to regulation complexities,

STANLEYFATMAX does not recommend air shipping lithium-ion

battery packs alone regardless of Watt Hour rating. Shipments of

tools with batteries (combo kits) can be air shipped as excepted

if the Watt Hour rating of the battery pack is no greater than

100Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely depleted

of charge. The battery pack will need to be recharged beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose towater.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge STANLEYFATMAX battery packs only

with designated STANLEYFATMAX chargers.

Charging battery packs other than the

designated STANLEYFATMAX batteries with a

STANLEYFATMAX charger may make them burst or

lead to other dangeroussituations.

Do not incinerate the batterypack.

Battery Type

The SFMCST933 operates on a 18 volt batterypack.

These battery packs may be used: SFMCB204, SFMCB202,

SFMCB206. Refer to Technical Data for moreinformation.

Package Contents

The package contains:

1 Grass Trimmer

1 Guard

1 Battery

1 Charger

10

ENGLISH

1 Instruction manual

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Do not expose the tool to rain or high

humidity

or leave outdoors while it israining.

Switch the tool off. Before performing any

maintenance on the tool, remove the battery

from thetool.

Keep people and animals at least 6 m away

from the workarea.

Keep bystandersaway.

96

Directive 2000/14/EC guaranteed soundpower.

Date Code Position (Fig.J)

The date code

18

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2019 XX XX

Year of Manufacture

Description (Fig.A)



WARNING: Never modify the power tool or

any part of it. Damage or personal injury couldresult.

1

On/Off trigger

2

Lock-off button

3

Speed control switch

4

Main handle

5

Auxiliary handle

6

Height-adjust collar

7

Turn-to-edge collar

8

Trimmer head

9

Wire edge guide

10

Spool housing

11

Guard

12

Battery housing

13

Battery pack

14

Battery release button

15

Auxiliary handle

adjustment buttons

Intended Use

This Grass Trimmer is designed for professional

trimmingapplications.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

This is not an edger and is not intended to be used foredging.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

ASSEMBLY AND ADJUSTMENTS



WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect battery

pack before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.



WARNING: Use only STANLEYFATMAX

battery packs andchargers.

Inserting and Removing the Battery Pack

from the Tool (Fig.F)

NOTE: Make sure your battery pack

13

is fullycharged.

To Install the Battery Pack into the Tool

1. Align the battery pack

13

with the rails inside the tool

(Fig.C).

2. Slide it into the tool until the battery pack is firmly seated

and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button

14

and firmly pull the battery pack

out of the toolhandle (Fig.F).

11

ENGLISH

2. Insert battery pack into the charger as described in the

charger section of thismanual.

Fuel Gauge Battery Packs (Fig.F)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button

25

. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Attaching Guard (Fig.B, C)



WARNING: Never remove the guard. Damage

or personal injury couldresult.



WARNING: NEVER OPERATE APPLIANCE

WITHOUT GUARD FIRMLY IN PLACE. The guard must

always be properly attached on the appliance to protect

theuser.

1. Remove the guard screws

16

.

2. Slide the guard

11

fully onto the trimmer head

8

.

Make sure the tabs on the guard engage the ribs on the

trimmerhead.

3. Continue to slide the guard on until it “snaps”into place. The

locking tab should snap into the housingslot.

4. Using a crosshead screwdriver, insert the guard screw and

tightensecurely.

5. Once the guard is installed, remove the covering from the

line cut-off blade, located on the edge of theguard.

Attaching the Auxiliary Handle (Fig.D)

For some models the auxiliary handle may need to be attached.

If the model needs the auxiliary handle attached, please refer to

theseinstructions.

1. To attach the auxiliary handle

5

, press in on the auxiliary

handle adjustment buttons

15

on both sides of the upper

housing as shown in Figure D.

2. Position the auxiliary handle as shown in Figure D . Partially

push the auxiliary handle on so it will hold the buttons in

when you release them with your hand.

3. Push the auxiliary handle completely onto the housing and

position it slightly until it “snaps” intoplace.

NOTE: To adjust the auxiliary handle up or down, press in on the

buttons and raise or lower the handle.

NOTE: The handle should be adjusted so that your front arm is

straight when the trimmer is in the workingposition.

Height Adjustment (Fig.E)



CAUTION: Adjust the length of the trimmer to

obtain proper workingpositions.

1. The overall height of the trimmer can be adjusted by

loosening the height-adjust collar

6

by rotating it in the

direction of the arrow shown in Figure E.

2. Move the upper housing straight up or down. When the

desired height is achieved, tighten the collar by rotating it

opposite of the direction shown in FigureE.

Releasing the Cutting Line (Fig.A)

In transit, the cutting line is taped to the spool housing

10

.

• Remove the tape holding the cutting line to the

spoolhousing.

OPERATION

Instructions for Use



WARNING: Always observe the safety

instructions and applicableregulations.



WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect battery

pack before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Proper Hand Position (Fig.A, I)



WARNING: To reduce the risk of serious

personal injury, ALWAYS use proper hand position

asshown.



WARNING: To reduce the risk of serious

personal injury, ALWAYS hold securely in anticipation of a

suddenreaction.

Hold the handle

4

with one hand. as shown in figure I

Switching Trimmer On and Off (Fig.A)



WARNING: Never attempt to lock the trigger

in the onposition.

To turn the appliance on, squeeze the lock-off button

2

and

then the On/Off trigger

1

. Once the unit is running, you may

release the lock off button. To turn the appliance off, release the

On/Offtrigger.

Speed Control Switch (Fig.A)

This string trimmer gives you the choice to operate at a

more efficient speed to extend the runtime for larger jobs, or

accelerate the trimmer speed for high-performancecutting.

12

ENGLISH

To extend runtime, pull the speed control switch back toward

the battery housing

12

into the "LO" position. This mode is best

for larger projects that require more time tocomplete.

To accelerate the trimmer, push the speed control switch

3

forward toward the auxillary handle

5

into the "HI" position.

This mode is best to cut through heavier growth and for

applications that need higherRPM.

NOTE: When in "HI" mode, runtime will be decreased as

compared to when trimmer is in "LO"mode.

Trimming (Fig.H, I)

With the trimmer on, angle it and swing side to side as shown

in FigureH.

Maintain a cutting angle of 5° to 10° as shown in Figure I. Do not

exceed 10°. Cut with the tip of the line.

Maintain a minimum distance of 610 mm between the guard

and your feet as shown in FigureI.

Convert to Edging Mode (Fig.J)



CAUTION: The wire edge guide should only be

used when in the edging mode.

The trimmer can be used in trimming mode or edging mode to

trim overhanging grass along lawn edges and flower beds. To

convert the trimmer to edging mode:

1. Remove the battery from thetrimmer.

2. Grasp the turn-to-edge collar

7

and pull down as shown

in Figure J.

3. Rotate the turn-to-edge collar 180° counterclockwise as

shown in Figure J., until the handle snaps back into the

upper half of the trimmer.

4. To return to trimming position, pull the turn-to-edge

collar up and rotate the head clockwise back to its

originalposition.

NOTE: You will experience faster than normal cutting line wear

if the trimmer line is positioned directly over the sidewalk or

abrasivesurface.

Edging Mode Operation (Fig.A, H)



WARNING: When being used as an edger,

stones, pieces of metal and other objects can be thrown

out at high speed by the line. The trimmer and guard are

designed to reduce the danger.

However, MAKE SURE that other persons and pets are at least

100' (30 m) away. Optimum cutting results are achieved on

edges deeper than 50mm.

• Do not use this trimmer to createtrenches.

• Using the wire edge guide

9

, guide thetrimmer.

• Position the wire edge guide on the edge of the sidewalk or

abrasive surface so the cutting line is over the grass or dirt

area to beedged.

• To make a closer cut, slightly tilt thetrimmer.

Helpful Cutting Tips (Fig.K)

• Use the tip of the string to do the cutting; do not force string

head into uncutgrass. Use edge guide along such things as

fences, houses and flower beds for bestpractices.

• Wire and picket fences cause extra string wear, even

breakage. Stone and brick walls, curbs, and wood may wear

stringrapidly.

• Do not allow spool cap

18

to drag on ground or

othersurfaces.

• In long growth, cut from the top down and do not exceed

305 mmhigh.

• Keep trimmer tilted toward the area being cut; this is the

best cuttingarea.

• The trimmer cuts when passing the unit from the left to

right. This will avoid throwing debris at theoperator.

• Avoid trees and shrubs. Tree bark, wood moldings, siding,

and fence posts can easily be damaged by thestring.

Cutting Line/Line Feeding

Your trimmer uses 1.65 mm diameter, ROUND nylon line. During

use, the tips of the nylon lines will become frayed and worn and

the special self feeding spool will automatically feed and trim

a fresh length of line. Cutting line will wear faster and require

more feeding if the cutting or edging is done along sidewalks

or other abrasive surfaces or heavier weeds are being cut. The

advanced automatic line feeding mechanism senses when more

cutting line is needed and feeds and trims the correct length

of line whenever it’s required. Do not bump unit on ground in

attempt to feed line or for any otherpurposes.

Clearing Jams and Tangled Line (Fig.K)



WARNING: Remove the battery from the

trimmer before making any assembly, adjustments or

changing accessories. Such preventive safety measures

reduce the risk of starting the applianceaccidentally.

From time to time, especially when cutting thick or stalky

weeds, the line feeding hub may become clogged with sap or

other material and the line will become jammed as a result. To

clear the jam, follow the steps listedbelow.



CAUTION: To avoid appliance damage, if the

cutting line protrudes beyond the trimming blade, cut it off

so that it just reaches theblade.

1. Remove the battery from thetrimmer.

2. Press the release tabs

19

on the spool cap

18

, and remove

the spool cap from the spool housing

10

(Figure K).

3. Pull the nylon line spool out and clear any broken line or

cutting debris from the spool area.

4. Place spool and line into spool cap with line “parked” in

slotsprovided.

5. Insert the line end through the appropriate hole in the

spool housing. Pull slack line through until it pulls out of the

holdingslots.

13

ENGLISH

6. Press the spool down GENTLY and rotate it until you feel it

drop into place and then push to snap into place. (When in

place, the spool will turn a few degrees left and right freely).

7. Take care to keep the line from becoming trapped under

thespool.

8. Fit the spool onto the appliance as described in Replacing

SpoolAssembly.

Replacing Spool Assembly (Fig.K, L)



WARNING: The use of any accessory not

recommended by STANLEYFATMAX for use with this

appliance could behazardous.



WARNING: Do not use any blades, or any

accessory or attachment other than those recommended

by STANLEYFATMAX on this trimmer. Serious injury or

product damage mayresult.

Reload nylon line (either bulk or prewound replacement spool)

as shown in thismanual.

USE ONLY 1.65 mm DIAMETER ROUND NYLON MONOFILAMENT

LINE. Do not use serrated or heavier gauge line, as they will

overload the motor and cause overheating. This line is available

at your local dealer or authorized servicecenter.

1. Remove battery fromappliance.

2. Press the release tabs

19

on the spool cap

18

, and remove

the spool cap from the spool housing

10

(Figure K).

3. For best results, replace spool and line with

STANLEYFATMAX Model # STZST12169/STZST121693

or replace cap only with STANLEYFATMAX

Model#STZST1326.

4. If lever in base of housing becomes dislodged, replace in

correct position before inserting new spool intohousing.

5. Remove any dirt and grass from the spool cap and

spool housing.

6. Unfasten the end of the cutting line and guide the line into

the eyelet.

7. Take the new spool and push it onto the boss

20

in the

housing. Rotate the spool slightly until it isseated.

8. The line should protrude approximately 5-136mm from

thehousing.

9. Align the release tabs on the spool cap with the slots in the

spoolhousing.

10. Snap the spool cap back on by depressing release tabs and

pressing into spoolhousing.

11. Push the cap onto the housing until it snaps securely

intoplace.

NOTE: Make sure that cover is fully positioned, listen for two

audible clicks to ensure both release tabs are correctly located.

Power the appliance on. In a few seconds or less you’ll hear the

nylon line being cut automatically to the properlength.

NOTE: Other replacement parts (guards, spool caps, etc.) are

available through authorized service centers.

Rewinding Spool from Bulk Line (use only

1.65 mm ROUND diameter line) (Fig.A, M, N)

Bulk line is also available for purchase from your local retailer.

NOTE: Hand wound spools from bulk line are likely to become

tangled more frequently than STANLEYFATMAX factory wound

spools. For best results, factory wound spools arerecommended.

1. Remove battery fromappliance.

2. Remove the empty spool from the appliance as described in

Replacing SpoolAssembly.

3. Remove any remaining cutting line from the spool

21

.

4. Make a fold at the end of the cutting line at about 19

mm. Feed the cutting line into one of the line anchoring

slots

22

.

5. Insert the 19 mm end of the bulk line into the hole

23

in

the spool adjacent to the slot. Make sure the line is pulled

tight against thespool.

6. Wind the cutting line onto the spool in the direction of the

arrow on the spool. Make sure to wind the line on neatly

and in layers. Do notcrisscross.

7. When the wound cutting line reaches the recesses

24

cut

theline.

8. Fit the spool onto the appliance as described in Replacing

SpoolAssembly.

MAINTENANCE

Your STANLEYFATMAX power tool has been designed

to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon

proper tool care and regularcleaning.



WARNING: To reduce the risk of serious

personal injury, turn tool off and disconnect battery

pack before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Lubrication

Your power tool requires no additionallubrication.

Cleaning



WARNING: Blow dirt and dust out of the

main housing with dry air as often as dirt is seen collecting

in and around the air vents. Wear approved eye protection

and approved dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh

chemicals for cleaning the non-metallic parts of the

tool. These chemicals may weaken the materials used in

14

ENGLISH

these parts. Use a cloth dampened only with water and

mild soap. Never let any liquid get inside the tool; never

immerse any part of the tool into aliquid.

Optional Accessories



WARNING: Since accessories, other than

those offered by STANLEYFATMAX, have not been tested

with this product, use of such accessories with this tool

could be hazardous. To reduce the risk of injury, only

STANLEYFATMAX recommended accessories should be

used with thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails to

produce sufficient power on jobs which were easily done before.

At the end of its technical life, discard it with due care for our

environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Guarantee

1 Year Guarantee

All STANLEY FATMAX power tool products include a 1 year

guarantee as standard. In the unlikely event that your powertool

becomes defective due to faulty materials or worksmanship

within 1 year of purchase, STANLEY guarantees to replace or

repair all defective parts free of charge, or – at our discretion –

replace the item free ofcharge.

3 Year Guarantee

Register your STANLEY FATMAX power tool within 4 weeks

of purchase and qualify for an additional 2 year guarantee.

Having registered your power tool, in the unlikely event that

your powertool becomes defective due to faulty materials or

worksmanship, STANLEY guarantees to replace or repair all

defective parts free of charge, or – at our discretion – replace the

item free ofcharge.

15

DEUTSCH

schützen, wie: Erhalt des Werkzeugs und Zubehörs, Hände

warm halten, Organisation vonArbeitsmustern.

Akku Katalognr. Ausgangsspannung

Ladegerät

SFMCB12

SFMCB202 18 X

SFMCB204 18 X

SFMCB206 18 X

"X" Zeigt an, dass der Akku mit diesem speziellen Ladegerät

kompatibel ist. Lesen Sie die Betriebsanleitung für

genauereInformationen.

EG-Konformitätserklärung

Maschinenrichtlinie

Rasen-Trimmer

SFMCST933

STANLEYFATMAX erklärt, dass diese unter Technische Daten

beschriebenen Geräte übereinstimmen mit:

2006/42/EC, EN60335-1:2012 + A11:2014, EN50636-2-91:2014.

2000/14/EG, Rasentrimmer, L ≤ 50 cm, Anhang VI

DEKRA Certification B.V.

Meander 1051 / P.O. Box 5185

6525 MJ ARNHEM / 6802 ED

ARNHEM, Niederlande

Kennnummer der benannten Stelle: 0344

Schallpegel gemäß 2000/14/EG

(Artikel 12, Anhang III, L ≤ 50 cm):

L

PA

(gemessener Schallleistungspegel) 81 dB(A)

Unsicherheitsfaktor (K) = 1,8 dB (A)

L

WA

(garantierte Schallleistung) 96 dB(A)

Diese Produkte erfüllen auch die Richtlinie 2014/30/EU und

2011/65/EU. Für weitere Informationen wenden Sie sich bitte an

STANLEYFATMAX unter der folgenden Adresse oder schauen

Sie auf der Rückseite dieser Betriebsanleitungnach.

Der Unterzeichnete ist verantwortlich für die Zusammenstellung

des technischen Dossiers und gibt diese Erklärung im Namen

von STANLEYFATMAXab.

A. P. Smith

Technical Director

STANLEYFATMAX Europe, Egide Walschaertsstraat 14-18,

2800 Mechelen, Belgien

14.08.2019

Herzlichen Glückwunsch!

Sie haben sich für ein Gerät von STANLEYFATMAX entschieden.

Langjährige Erfahrung, sorgfältige Produktentwicklung und

Innovation machen STANLEYFATMAX zu einem zuverlässigen

Partner für professionelle Anwender vonElektrowerkzeugen.

Technische Daten

SFMCST933

Spannung V

DC

18

Typ 1

U/min /min 5500-7200

Schnittlänge mm 330

Gewicht (ohne Akku) kg 2,4

Lärmwerte und Vibrationswerte (Triax-Vektorsumme). Rasen-Trimmer-Modus

gemäß EN50636-2-91:

L

PA

(Emissions-

Schalldruckpegel)

dB(A) 81,0

L

WA

(Schallleistungspegel) dB(A) 94

K (Unsicherheit für den

angegebenen Schallpegel)

dB(A) 1,8

Vibrationsemissionswert a

h

= m/s² 3,1

Unsicherheitsfaktor K = m/s² 1,5

Der in diesem Informationsblatt angegebene

Vibrationsemissionswert wurde gemäß einem standardisierten

Test laut EN50636 gemessen und kann für einen Vergleich

zwischen zwei Geräten verwendet werden. Er kann zu einer

vorläufigen Einschätzung der Exposition verwendetwerden.



WARNUNG: Der angegebene

Vibrationsemissionswert bezieht sich auf die

Hauptanwendung des Gerätes. Wenn das Gerät

jedoch für andere Anwendungen, mit anderem

Zubehör oder schlecht gewartet eingesetzt wird, kann

die Vibrationsemission verschieden sein. Dies kann

den Expositionsgrad über die Gesamtbetriebszeit

erheblicherhöhen.

Eine Schätzung der Vibrationsstärke sollte auch

berücksichtigen, wie oft das Gerät ausgeschaltet

wird oder über welche Zeit es zwar läuft, aber nicht

wirklich in Betrieb ist. Dies kann die Exposition über die

Gesamtbetriebszeit erheblichmindern.

Identifizieren Sie zusätzliche Sicherheitsmaßnahmen,

um den Bediener vor den Vibrationsauswirkungen zu

RASENTRIMMER

SFMCST933

Deutsch (übersetzt von den originalanweisungen)

Akkus

Ladegeräte/Ladedauer (Minuten)

Kat #

GS

Gewicht

16

DEUTSCH

WICHTIG

VOR DER VERWENDUNG SORGFÄLTIG DURCHLESEN

FÜR ZUKÜNFTIGE BEZUGNAHME AUFBEWAHREN

SICHERE BETRIEBSPRAKTIKEN

Schulung

a ) Lesen Sie die Bedienungsanleitung sorgfältig durch.

Machen Sie sich mit den Bedienelementen und dem

korrekten Gebrauch der Maschinevertraut.

b ) Das Gerät darf nicht von Kindern oder Personen, die

die vorliegenden Anleitungen nicht gelesen haben,

genutzt werden. Örtliche Bestimmungen können das

Alter des Bedienerseinschränken.

c ) Beachten Sie, dass der Bediener bzw. Benutzer für

eventuelle Personen- oder Sachschäden verantwortlichist.

Vorbereitung

a ) Führen Sie vor dem Gebrauch der Maschine immer

eine Sichtprüfung auf beschädigte, fehlende oder

falsch angebrachte Schutzvorrichtungen oder

Abschirmungendurch.

b ) Es sollte stets ein Sicherheitsabstand zu anderen Personen,

insbesondere Kindern, und Haustieren eingehaltenwerden.

Betrieb

a ) Tragen Sie während des Betriebs der Maschine stets einen

Augenschutz und festeSchuhe.

b ) Vermeiden Sie, das Gerät bei schlechtem Wetter zu

verwenden, vor allem, wenn das Risiko von Blitzenbesteht.

c ) Betreiben Sie das Gerät nur bei Tageslicht oder bei

ausreichenderBeleuchtung.

d ) Betreiben Sie das Gerät keinesfalls, wenn die

Schutzvorrichtungen oder Abschirmungen beschädigt

oder nicht ordnungsgemäß angebrachtsind.

e ) Schalten Sie das Gerät nur ein, wenn Hände und Füße die

Schneidmesser nichtberühren.

f ) Trennen Sie die Maschine immer von der

Stromversorgung (d.h. ziehen Sie den Stecker aus der

Steckdose, entfernen Sie das Deaktivierungsgerät oder den

austauschbaren Akku).

• wenn die Maschine unbeaufsichtigt gelassen wird;

• bevor Blockaden entfernt werden;

• bevor Sie die Maschine überprüfen, reinigen oder an

ihr arbeiten;

• nach dem Überfahren eines Fremdkörpers;

• wenn das Gerät ungewöhnlich stark zu

vibrierenbeginnt.

g ) Schützen Sie Füße und Hände vor Verletzungen durch

dieSchneidmesser.

h ) Stellen Sie stets sicher, dass die Lüftungsöffnungen frei von

Verschmutzungensind.

i ) Entfernen Sie alle Objekte, die einen Rückschlag

verursachen könnten, beispielsweise Äste undSteine.

WARNUNG: Zur Reduzierung der

Verletzungsgefahr bitte die Betriebsanleitunglesen.

Definitionen: Sicherheitsrichtlinien

Im Folgenden wird die Relevanz der einzelnen Warnhinweise

erklärt. Bitte lesen Sie die Betriebsanleitung und achten Sie auf

dieseSymbole.



GEFAHR: Weist auf eine unmittelbar drohende

gefährliche Situation hin, die, sofern nicht vermieden,

zu tödlichen oder schweren Verletzungen führenwird.



WARNUNG: Weist auf eine möglicherweise

gefährliche Situation hin, die, sofern nicht vermieden, zu

tödlichen oder schweren Verletzungen führenkann.



VORSICHT: Weist auf eine möglicherweise

gefährliche Situation hin, die, sofern nicht vermieden,

zu leichten oder mittelschweren Verletzungen

führenkann.

HINWEIS: Weist auf ein Verhalten hin, das

nichts mit Verletzungen zu tun hat, aber, wenn es nicht

vermieden wird, zu Sachschäden führenkann.



Weist auf ein Stromschlagrisikohin.



Weist auf eine Brandgefahrhin.

SICHERHEITSHINWEISE



WARNUNG: Beachten Sie beim Umgang mit

netzstrombetriebenen Geräten stets die grundlegenden

Sicherheitshinweise, die im Folgenden beschrieben

werden. Dadurch verhindern Sie Brände, Stromschläge

sowie Sach- undPersonenschäden.



WARNUNG: Beachten Sie beim Verwenden

des Geräts unbedingt die Sicherheitsregeln. Lesen Sie

zu Ihrer eigenen Sicherheit und zum Schutz in der Nähe

befindlicher Personen vor Gebrauch des Geräts die

folgende Bedienungsanleitung. Heben Sie diese Anleitung

zur späteren Verwendung gutauf.

• Lesen Sie diese Anleitung vollständig und aufmerksam durch,

bevor Sie das Gerätverwenden.

• Der vorgesehene Verwendungszweck ist in dieser Anleitung

beschrieben. Bei Verwendung von Zubehör oder Anbauteilen,

die nicht in dieser Anleitung empfohlen werden, sowie bei

der Verwendung des Geräts in Abweichung von den in dieser

Anleitung beschriebenen Verfahren bestehtVerletzungsgefahr.

• Bewahren Sie diese Anleitungauf.

17

DEUTSCH

j ) Suchen Sie nach losen Befestigungselementen

und beschädigten Teilen, beispielsweise Risse in

derSchneideinrichtung.

Handhabung und Lagerung

a ) Trennen Sie die Maschine von der Stromversorgung

(d.h. ziehen Sie den Stecker aus der Steckdose,

entfernen Sie das Deaktivierungsgerät oder den

austauschbaren Akku), bevor Sie Wartungs- oder

Reinigungsarbeitendurchführen.

b ) Verwenden Sie nur vom Hersteller empfohlene Ersatz-

undZubehörteile.

c ) Kontrollieren und warten Sie das Gerät

regelmäßig. Lassen Sie das Gerät nur in autorisierten

Werkstättenreparieren.

d ) Bewahren Sie das Gerät bei Nichtgebrauch außerhalb der

Reichweite von Kindernauf.

e ) Verwenden Sie für Transport und Lagerung eine

Klingenabdeckung fürMetallklingen.

f ) Vor der Lagerung reinigen und Schutzvorrichtungen für

Schneidwerkzeuge mit Metallklingenanbringen.

ZUSÄTZLICHE SICHERHEITSHINWEISE FÜR

RASENTRIMMER



WARNUNG: Die Messer laufen nach dem

Abschalten des Motors nochaus.

• Tragen Sie lange Hosen, um Ihre Beine zuschützen.

• Vergewissern Sie sich vor Verwenden des Geräts, dass die

zu beschneidende Fläche frei von Ästen, Steinen, Draht und

anderen Objektenist.

• Verwenden Sie das Gerät ausschließlich in aufrechter Stellung

und mit Schneidfaden in Bodennähe. Schalten Sie das Gerät

keinesfalls in einer anderen Stellungein.

• Achten Sie bei Verwendung des Geräts auf langsame

Bewegungen. Achten Sie darauf, dass frisch gemähtes Gras

feucht und rutschig seinkann.

• Arbeiten Sie nie an steilen Hängen. Arbeiten Sie mit dem Gerät

immer parallel zum Hang, nie den Hang hinauf oderhinunter.

• Schalten Sie das Gerät vor dem Überqueren von Kieswegen

und Straßenaus.

• Berühren Sie niemals den Schneidfaden, während sich das

Gerät in Betriebbefindet.

• Warten Sie stets, bis der Schneidfaden vollständig zum

Stillstand gekommen ist, bevor Sie das Gerätabsetzen.

• Verwenden Sie ausschließlich geeignete Schneidfäden.

Verwenden Sie keinesfalls Schneidfäden aus Metall

oderAngelschnur.

• Halten Sie Hände und Füße stets von Schneidfaden und -klinge

fern, insbesondere beim Einschalten desGeräts.

• Überprüfen Sie das Gerät vor Gebrauch und nach Stößen

auf Beschädigungen und Verschleiß, und veranlassen Sie

notwendigeReparaturmaßnahmen.

• Schützen Sie sich vor Verletzungen beim Verwenden von

Geräten zum Verkürzen des Schneidfadens. Bringen Sie nach

Herausziehen des neuen Schneidfadens das Gerät vor dem

Einschalten in die normaleBetriebsposition.

• Seien Sie besonders vorsichtig, wenn Sie das Gerät in der Nähe

von Kindernverwenden.

• Das Gerät ist nicht für die unbeaufsichtigte Verwendung durch

Kinder oder gebrechliche Personenvorgesehen.

• Das Gerät ist keinSpielzeug.

• Verwenden Sie das Gerät nur in trockener Umgebung. Achten

Sie darauf, dass das Gerät nicht nasswird.

• Tauchen Sie das Gerät nicht inWasser.

• Versuchen Sie nicht, das Gehäuse zu öffnen. Im Inneren

befinden sich keine zu wartendenTeile.

• Betreiben Sie das Gerät nicht in explosionsgefährdeter

Umgebung, in der sich brennbare Flüssigkeiten, Gase oder

Staubbefinden.

• Wenn das Gerät in einem Fahrzeug transportiert oder gelagert

wird, bewahren Sie es im Kofferraum oder einer geeigneten

Ablage auf, damit es bei plötzlichen Geschwindigkeits- oder

Richtungsänderungen nicht in Bewegung geratenkann.

• Bewahren Sie das Gerät bei Nichtgebrauch an einem

trockenen, gut belüfteten Ort außerhalb der Reichweite von

Kindernauf.

• Kinder sollten keinen Zugang zu aufbewahren Gerätenhaben.

Sicherheit anderer Personen

• Dieses Gerät darf nicht von Personen (einschließlich Kindern)

mit eingeschränkten physischen, sensorischen oder mentalen

Fähigkeiten oder ohne ausreichende Erfahrung oder

Kenntnisse verwendet werden, außer wenn diese Personen von

einer Person, die für ihre Sicherheit verantwortlich ist, bei der

Verwendung des Geräts beaufsichtigt oder mit ihm vertraut

gemachtwerden.

• Kinder müssen beaufsichtigt werden, um sicherzustellen, dass

sie nicht mit dem Gerätspielen.

Restrisiken

Damit Sie an Hängen guten Stand haben, sollten Sie keine

anormale Körperhaltung einnehmen. Halten Sie jederzeit

das Gleichgewicht. Beim Umgang mit dem Gerät nur gehen,

nichtrennen.

Zusätzliche Restrisiken können auftreten, wenn das

Werkzeug verwendet wird, das möglicherweise nicht in den

Sicherheitswarnungen enthalten ist. Diese Risiken können aus

Missbrauch, verlängerter Nutzung usw.resultieren.

Selbst unter Beachtung der geltenden Sicherheitsvorschriften

und des Einsatzes von Schutzvorrichtungen können bestimmte

Risiken nicht vermieden werden. Diese sind:

• Verletzungen, die durch das Berühren von sich drehenden/

bewegenden Teilen verursachtwerden.

• Verletzungen, die durch das Austauschen von Teilen, Messern

oder Zubehör verursachtwerden.

• Verletzungen, die durch längeren Gebrauch eines Geräts

verursacht werden. Bei der längeren Verwendung eines

18

DEUTSCH

Werkzeugs ist sicherzustellen, dass regelmäßig Pausen

eingelegtwerden.Schwerhörigkeit.

• Gesundheitsrisiken durch das Einatmen von Staub beim

Gebrauch des Geräts (Beispielsweise bei Holzarbeiten,

insbesondere Eiche, Buche und Pressspan).

Elektrische Sicherheit

Der Elektromotor wurde für eine einzige Spannung konstruiert.

Überprüfen Sie immer, dass die Spannung des Akkus der

Spannung auf dem Typenschild entspricht. Überprüfen

Sie auch, dass die Spannung des Ladegeräts der Ihres

Stromnetzesentspricht.

Ihr STANLEYFATMAX-Ladegerät ist gemäß

EN60335 doppelt isoliert. Es muss deshalb nicht

geerdetwerden.



WARNUNG: 115V-Geräte müssen

über einen ausfallsicheren Trenntransformator mit

einer Abschirmung gegen Erde zwischen Primär- und

Sekundärwicklung betrieben werden.

Wenn das Stromversorgungskabel beschädigt ist, muss es durch

ein speziell ausgestattetes Kabel ersetzt werden, das bei der

STANLEYFATMAX Kundendienstorganisation erhältlichist.

Verwendung eines Verlängerungskabels

Ein Verlängerungskabel sollte nur wenn unbedingt nötig

verwendet werden. Verwenden Sie ein zugelassenes

Verlängerungskabel, das für die Leistungsaufnahme Ihres

Ladegeräts geeignet ist (siehe Technische Daten). Der

Mindestquerschnitt der Leitungen beträgt 1mm

2

; die

Höchstlänge beträgt30m.

Wenn Sie eine Kabeltrommel verwenden, wickeln Sie das Kabel

vollständigab.

BEWAHREN SIE DIESE ANWEISUNGEN AUF

Ladegeräte

An STANLEYFATMAX-Ladegeräten müssen keine Einstellungen

vorgenommen werden, und sie wurden für eine möglichst

einfache Bedienungkonzipiert.

Wichtige Sicherheitsvorschriften für alle

Batterieladegeräte

BEWAHREN SIE DIESE ANWEISUNGEN AUF: Dieses Handbuch

enthält wichtige Sicherheits- und Betriebsanweisungen für

kompatible Ladegeräte (siehe Technische Daten).

• Lesen Sie vor der Verwendung des Ladegeräts alle

Anweisungen und Warnhinweise auf dem Ladegerät und

demAkku.



WARNUNG: Stromschlaggefahr. Keine

Flüssigkeiten in das Ladegerät gelangen lassen. Dies kann

einen elektrischen Schlag zur Folgehaben.



WARNUNG: Wir empfehlen die Verwendung

eines Fehlerstromschutzgeräts mit einem Fehlerstrom von

maximal 30mA.



VORSICHT: Verbrennungsgefahr. Zur

Reduzierung der Verletzungsgefahr sollten nur Akkus

von STANLEYFATMAX verwendet werden. Andere

Akkutypen können bersten und Verletzungen und

Sachschädenverursachen.



VORSICHT: Lassen Sie nicht zu, dass Kinder

mit dem Gerätspielen.

HINWEIS: Wenn das Ladegerät in die

Steckdose gesteckt wird, können die Ladekontakte

im Ladegerät unter bestimmten Bedingungen durch

Fremdmaterial kurzgeschlossen werden. Leitfähige

Fremdmaterialien, z.B. unter anderem Stahlwolle,

Alufolie oder angesammelte Metallpartikel, sollten von

Hohlräumen des Ladegeräts ferngehalten werden. Ziehen

Sie den Netzstecker des Ladegerätes immer aus der

Steckdose, wenn kein Akku in der Vertiefung steckt. Ziehen

Sie den Netzstecker des Ladegerätes vor dem Reinigen aus

derSteckdose.

• Versuchen Sie NICHT, den Akku mit anderen

Ladegeräten aufzuladen als die in diesem Handbuch

angegebenen. Das Ladegerät und der Akku wurden speziell

zur gemeinsamen Verwendungkonzipiert.

• Diese Ladegeräte sind ausschließlich zum Laden von

STANLEYFATMAX-Akkus bestimmt. Eine anderweitige

Verwendung kann zu Brand führen oder gefährliche oder

tödliche Verletzungen durch Stromschlagverursachen.

• Setzen Sie das Ladegerät weder Regen noch Schneeaus.

• Ziehen Sie am Stecker und nicht am Kabel, wenn Sie das

Ladegerät von der Steckdose trennen. Dadurch wird das

Risiko einer Beschädigung von Stecker und Kabelreduziert.

• Stellen Sie sicher, dass das Kabel so verlegt wird, dass

nicht darauf getreten bzw. darüber gestolpert oder es

anderweitig beschädigt oder belastetwird.

• Verwenden Sie kein Verlängerungskabel, wenn es

nicht unbedingt erforderlich ist. Ein ungeeignetes

Verlängerungskabel kann zu Brand führen oder

gefährliche oder tödliche Verletzungen durch einen

Stromschlagverursachen.

• Stellen Sie keine Gegenstände auf das Ladegerät

bzw. stellen Sie das Ladegerät nicht auf eine weiche

Oberfläche. Dadurch könnten die Lüftungsschlitze

blockiert und das Gerät überhitzt werden. Stellen Sie das

Ladegerät von Hitzequellen entfernt auf. Das Ladegerät ist

oben und unten am Gehäuse mit Lüftungsschlitzenversehen.

• Betreiben Sie das Ladegerät nicht mit beschädigtem

Kabel oder Stecker – lassen Sie die Teile ggf.

sofortaustauschen.

• Benutzen Sie das Ladegerät nicht, wenn es einen

harten Stoß erlitten hat, fallen gelassen oder

anderweitig beschädigt wurde. Bringen Sie es zu einer

autorisiertenKundendienststelle.

La pagina sta caricando ...

Stanley FATMAX SFMCST933 Manuale del proprietario

Questo manuale è adatto anche per

Stanley FATMAX SFMCST933 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti