Ubiquiti AIRCAM Guida Rapida

Security Camera

1

Introduction

Thank you for purchasing the airCam

™

. This Quick Start Guide is

designed to guide you through the installation of the airCam and

show you how to access the airCam's configuration interface. This

Quick Start Guide also includes the warranty terms.

The airVision

™

software and User Guide are available for download

at downloads.ubnt.com/airvision.

The hardware installation process is different for indoor and

outdoor installations. After familiarizing yourself with the

airCam in the Hardware Overview section, please proceed to the

appropriate installation section:

• "Outdoor Installation" on page 4

• "Indoor Installation" on page 8

Package Contents

Camera Mounting Bracket 24V PoE Adapter Power Cord

Security Camera

Seal Self-Tapping

Screws (Qty. 3)

Screw Anchors

(Qty. 3)

Quick Start Guide

Installation Requirements

• Pencil

• Drill and 6mm drill bits

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.

2

airCam

Hardware Overview

Front

Sun Shade

Lens

remove plastic lens film

before use

3

Hardware Overview

Back

Plug

(for outdoor installations)

Ethernet Door

Mounting Slots

LEDs

Power The Power LED will light steady orange when the

airCam is connected to a power source.

Ethernet The Ethernet LED will light steady green when

an active Ethernet connection is made and flash when

there is activity.

4

airCam

Installation Overview

The installation process is different depending on whether you are

mounting the camera outdoors or indoors. Follow the instructions

for the installation that you are performing.

Outdoor Installation

Important: The ideal outdoor location for mounting the

airCam would be under an overhang/eave that shelters

the camera. If the airCam is located in a completely open

outdoor environment without an overhang/eave, do not

install camera with a downtilt of more than 45°.

45°

Celing Mount

Wall-Mount

Camera is at 45

degrees when the

indicator on the joint is

aligned with the corner

of the mounting arm.

5

Outdoor Installation

1. Press down on the release to remove the Ethernet Door.

Important: Do not remove the plug.

Plug

2. Connect the Ethernet cable to the Ethernet port.

6

airCam

3. Insert the Seal into the bottom of the camera and wrap the Seal

around the Ethernet cable. Reconnect the Ethernet Door to the

airCam, leaving the Ethernet cable fed through the seal at the

bottom of the camera.

4. Insert the Mounting Bracket into the Mounting Slots until a click

is heard to confirm a secure connection.

7

Outdoor Installation

5. There are three recessed areas for the Ethernet cable on the

Mounting Bracket Base. Thread the Ethernet cable through two

of the recessed areas and out the one that will be closest to your

power source.

Important: If the power source is above the camera, extend

the cable 70-80 mm below the camera body before routing

up to the power source.

6. Position the Mounting Bracket in the desired location and use a

pencil to mark the holes on the wall.

7. Use a 6 mm drill bit to drill the holes in the wall.

8. Insert a Screw Anchor into each hole.

9. Secure the Mounting Bracket to the wall using the Self-Tapping

Screws.

8

airCam

Indoor Installation

1. Remove the screw and knob that connect the Mounting

Bracket Base to the camera attachment by turning the knob

counter-clockwise.

Mounting Bracket Base

2. Insert an Ethernet cable through the Mounting Bracket Base.

3. Reconnect the Mounting Bracket Base to the camera

attachment by reconnecting the screw and knob. Turn the

knob clockwise to lock the camera attachment back to the

Mounting Bracket Base.

9

Indoor Installation

4. Unscrew the Plug on the back of the airCam.

5. Connect the Ethernet cable to the Ethernet port.

6. Insert the Mounting Bracket into the Mounting Slots until a click

is heard to confirm a secure connection.

10

airCam

7. Position the Mounting Bracket in the desired location and use a

pencil to mark the holes on the wall.

8. Use a 6 mm drill bit to drill the holes in the wall.

9. Insert the three Screw Anchors into the wall.

10. Secure the Mounting Bracket to the wall using the Self-Tapping

Screws.

Note: There are three recessed areas for the Ethernet

cable on the Mounting Bracket Base. Place the Ethernet

cable in the recessed area that will be closest to your

power source.

Connecting the Power

1. Connect the other end of the Ethernet cable to the Ethernet

port labeled POE on the PoE Adapter.

11

Connecting the Power

2. Connect an Ethernet cable from your LAN to the Ethernet port

labeled LAN on the PoE Adapter.

3. Connect the power cord to the power port on the PoE Adapter.

Connect the other end of the power cord to a power outlet.

The Power LED should light up on the airCam.

12

airCam

airVision

Download and install the latest version of the airVision software at

downloads.ubnt.com/airvision; the airVision auto management

feature should automatically detect and install your new camera.

• Go to the airVision interface to verify the camera is installed. It

should appear on the left under Unplaced Cameras.

• Drag the Camera to the appropriate location on the map.

• Click the Camera icon.

• Click the Live Feed icon and a live feed of the camera should

be displayed.

• Skip to Adjusting the Camera View on page 15.

13

Camera Configuration Interface

Access the Camera Configuration Interface if you have not yet

installed airVision, or plan to use the airCam as a stand-alone

camera without airVision.

1. Make sure that your host machine is connected to the same

LAN as the airCam.

2. The airCam is set to DHCP by default. If you have a router or

DHCP server providing addresses on your network, please

check your DHCP Client Table or download the Ubiquiti

Discovery Tool from:http://www.ubnt.com/download#app

Note: If you do not have a DHCP server, the airCam

defaults to the IP address 192.168.1.20.

4. Launch your web browser and in the address field, type

http:// and then the IP address of the airCam, for example:

http://192.168.1.20. Press enter (PC) or return (Mac).

5. The login screen will appear. Enter ubnt in the Username and

Password fields and click Login.

14

airCam

6. The Main screen will appear and you should see a live video

stream from the airCam.

Note: If you need to change the airCam network settings

(DHCP/Static), go to Network Settings on the Device tab.

15

Adjusting the Camera View

Adjusts Camera Side to Side

Adjusts Camera Up and Down

Adjusts Mounting

Bracket Base

Adjusts Camera Focus

Hardware installation is complete. For details on using the

airVision software or the Camera Configuration Interface,

download the User Guide from downloads.ubnt.com/airvision

16

airCam

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal physical,

electromagnetic or electrical stress, including lightning strikes, or

accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of the

RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

17

Limited Warranty

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty.

Disclaimer

EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI

NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,

SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM

AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,

EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,

REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,

ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,

SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY

WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR

TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.

BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR

ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE

TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING

THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE

SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS

AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS

FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD

PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,

DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT

CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY

OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant

that the operation of the Products will be error-free or that operation will

be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible

for damages or claims of any nature or description relating to system

performance, including coverage, buyer’s selection of products (including

the Products) for buyer’s application and/or failure of products (including

the Products) to meet government or regulatory requirements.

18

airCam

Limitation of Liability

EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL

UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR

DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES

(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING

OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE

PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER

LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

Note

Some countries, states and provinces do not allow exclusions of implied

warranties or conditions, so the above exclusion may not apply to you.

You may have other rights that vary from country to country, state to

state, or province to province. Some countries, states and provinces do not

allow the exclusion or limitation of liability for incidental or consequential

damages, so the above limitation may not apply to you. EXCEPT TO

THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO

NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE

MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY

SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations

Convention on Contracts for the International Sale of Goods shall not apply

to any transactions regarding the sale of the Products.

La pagina sta caricando ...

Ubiquiti AIRCAM Guida Rapida

Ubiquiti AIRCAM Guida Rapida

in altre lingue

Documenti correlati