Please read this manual carefully before operating
your set and retain it for future reference.
HLS36W (HLS36W, SHS36-D)
OWNER’S MANUAL
Speaker Sound Bar
P/NO : MFL67164758
ENGLISH
PORTUGUÊS
FRANÇAIS
ةيبرعلا
HLS36W-N0_DMARLLK_ENG_4758.indd 1 2011-02-22 �� 7:11:02
1 Getting Started
Getting Started2
Getting Started
1
Safety Information
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with
arrowhead symbol within an
equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the product’s enclosure
that may be of sucient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specication page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. hen installing the product, ensure
that the plug is easily accessible.
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, re or the like.
HLS36W-N0_DMARLLK_ENG_4758.indd 2 2011-02-22 �� 7:11:02
Getting Started 3
Getting Started
1
RF Radiation Exposure Statement
This equipment should be installed and operated
with minimum distance 20 cm between the
radiator and your body.
Italy Notice
A general authorization is requested for outdoor
use in Italy.
The use of these equipments is regulated by:
1. D.L.gs 1.8.2003, n. 259, article 104 (activity
subject to general authorization) for outdoor
use and article 105 (free use) for indoor use, in
both cases for private use.
2. D.M. 28.5.03, for supply to public of RLAN access
to networks and telecom services.
L’uso degli apparati è regolamentato da:
1. D.L.gs 1.8.2003, n. 259, articoli 104 (attività
soggette ad autorizzazione generale) se utilizzati
al di fuori del proprio fondo e 105 (libero uso) se
utilizzati entro il proprio
fondo, in entrambi i casi per uso private.
2. D.M. 28.5.03, per la fornitura al pubblico
dell’accesso R-LAN alle reti e ai servizi di
telecomunicazioni.
Brazil Notice
Este equipamento opera em caráter secundário, isto
é, não tem direito a proteção contra interferência
prejudicial, mesmo de estações do mesmo tipo, e
não pode causar interferência a sistemas operando
em caráter primário.
POWER: This unit operates on a mains supply of 200-
240V~, 50/60Hz.
WIRING: This unit is supplied with a BSI 1363 ap-
proved 13 amp mains plug, fused at 5 amp. When
replacing the fuse always use a 5 amp BS 1362, BSI or
ASTA approved type. Never use this plug with the fuse
cover omitted. To obtain a replacement fuse cover
contact your dealer. If the type of plug supplied is not
suitable for the mains sockets in your home, then the
plug should be removed and a suitable type tted.
Please refer to the wiring instructions below:
WIRING: A mains plug removed from the mains lead
of this unit must be destroyed. A mains plug with
bared wires is hazardous if inserted in a mains socket.
Do not connect either wire to the earth pin, marked
with the letter E or with the earth symbol
or
coloured green or green and yellow. If any other plug
is tted, use a 5 amp fuse, either in the plug, or at the
distribution board.
IMPORTANT: The wires in this mains lead are coloured
in accordance with the following codes:
- BLUE: NEUTRAL, BROWN: LIVE - As the colours
of the wires in the mains lead of this unit may not
correspond with the coloured marking identifying the
terminals in your plug, proceed as follows: The wire
which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black. The wire which is coloured brown must be con-
nected to the terminal which is marked with the letter
L or coloured red.
In NIGERIA
HLS36W-N0_DMARLLK_ENG_4758.indd 3 2011-02-22 �� 7:11:02
Table of Contents4
Table of Contents
1 Getting Started
2 Safety Information
6 Unique Features
6 – Portable In
6 – Speaker ez (easy) Setup
6 Accessories
7 Introduction
7 – Symbols Used in this Manual
7 Playable file
7 – MP3/ WMA music file requirement
8 Remote control
9 Front panel
9 Rear panel
2 Connecting
10 Mounting the main unit on a wall
12 Setting up
12 – Pairing wireless subwoofer
13 Optional Equipment Connection
13 – AUDIO (PORT. IN) In Connection
13 – Listening to music from your portable
player
13 – OPTICAL In connection
13 – Speaker ez (easy) setup
14 – USB Playback
3 Operating
15 Basic Operations
15 – USB Operation
15 Other Operations
15 – DOLBY DRC (Dynamic Range
Control)
15 – AV Sync
16 – Sleep Timer Setting
16 – Dimmer
16 – Turn off the sound temporarily
16 – Adjust the woofer level settings
16 – Displaying file and input source
17 Sound adjustment
17 – Setting the surround mode
18 Controlling a TV with the Supplied
Remote Control
18 – Setting up the remote to control your
TV
HLS36W-N0_DMARLLK_ENG_4758.indd 4 2011-02-22 �� 7:11:02
Table of Contents 5
1
2
3
4
5
4 Troubleshooting
19 Troubleshooting
5 Appendix
20 Maintenance
20 – Handling the Unit
21 Trademarks and Licenses
22 Specifications
HLS36W-N0_DMARLLK_ENG_4758.indd 5 2011-02-22 �� 7:11:02
Getting Started6
Getting Started
1
Unique Features
Portable In
Listen to music from your portable device. (MP3,
Notebook, etc)
Speaker ez (easy) Setup
Listen to sounds from TV, DVD or Digital device
with vivid 2.1 or 2.0 ch mode.
Accessories
Please check and identify the supplied accessories.
Remote control (1) Batteries (2)
WALL BRACKET
INSTALL GUIDE (1)
Wall bracket (1)
Optical cable (1)
HLS36W-N0_DMARLLK_ENG_4758.indd 6 2011-02-22 �� 7:11:03
Getting Started 7
Getting Started
1
Introduction
Symbols Used in this Manual
,
Note
Indicates special notes and operating features.
,
Tip
Indicates tip and hints for making the task easier.
>
Caution
Indicates cautions for preventing possible damages
from abuse.
Playable file
MP3/ WMA music file
requirement
MP3/ WMA le compatibility with this unit is limited
as follows :
y
Sampling frequency : within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
y
Bit rate : within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
y
Maximum les : Under 999
y
File extensions : “.mp3”/ “.wma”
HLS36W-N0_DMARLLK_ENG_4758.indd 7 2011-02-22 �� 7:11:03
Getting Started8
Getting Started
1
Remote control
Battery Installation
Remove the battery cover on the rear of the
Remote Control, and insert two (size AAA) battery
with and matched correctly.
• • • • • • • • • •
a
• • • • • • • • •
1
POWER: Switches the unit ON or OFF.
AV SYNC: Synchronizes the audio and video.
DOLBY DRC: Sets the Dobly DRC.
MUTE: Mutes the sound.
• • • • • • • • • •
b
• • • • • • • • •
FOLDER: Searches for a folder of MP3/ WMA les.
When a USB containing MP3/ WMA les in several
folders is being played, press FOLDER to select the
folder you want to play.
INPUT: Changes input sources.
OPTICAL: Changes input source to optical directly.
VOLUME: Adjusts speaker volume.
• • • • • • • • • •
c
• • • • • • • • •
SOUND EFFECT: Selects a sound eect mode.
WOOFER LEVEL: Sets the sound level of woofer.
REPEAT: Listens to your les repeatedly or
randomly.
C/V
: Goes to next or previous le.
Z
: Stops playback.
d/M
: Starts playback. / Pauses playback.
SLEEP: Sets the system to turn o automatically at
a specied time.
INFO.: Displays the le or input source information.
• • • • • • • • • •
d
• • • • • • • • •
TV Control buttons: See page 18
0 to 9 numerical buttons: Selects numbered
numbered les. Enters the PIN code.
HLS36W-N0_DMARLLK_ENG_4758.indd 8 2011-02-22 �� 7:11:03
Getting Started 9
Getting Started
1
A
Display
B
USB Port
C
F FUNCTION
Press it repeatedly to select other function.
D
I
STOP
E
T
PLAY / PAUSE
F
– VOL +
Adjusts speaker volume.
G
1
STANDBY/ON
Front panel
A
B
CDEFG
Rear panel
B
A
A
PORT. (Portable) IN
B
OPTICAL IN 1/ 2
HLS36W-N0_DMARLLK_ENG_4758.indd 9 2011-02-22 �� 7:11:03
2 Connecting
Connecting10
Connecting
2
Mounting the main
unit on a wall
You can mount the main unit on a wall.
Prepare screws and brackets.
Preperation
Unit
Wall bracket
WALL BRACKET
INSTALL GUIDE
1. Match the TV’s BOTTOM EDGE of WALL BRACKET
INSTALL GUIDE with the bottom of TV and
attach to the position.
Step 1
TV
2. When you mount it on a wall (concrete), use the
wall plugs (Not supplied). You should drill some
holes. A guide sheet (WALL BRACKET INSTALL
GUIDE) is supplied to drill. Use the sheet to
check the point to drill.
Step 2
Screws and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting. Please
purchase it.
,
Note
HLS36W-N0_DMARLLK_ENG_4758.indd 10 2011-02-22 �� 7:11:03
Connecting 11
Connecting
2
3. Remove the WALL BRACKET INSTALL GUIDE.
4. Fix it with screws (not supplied) as shown in the
illustration below.
Step 4
Detach the unit from the bracket as shown
below.
,
Note
5. Hang the main unit onto the bracket as shown
below.
Step 5
You can arrange power cord cable with the
bracket as shown below.
Power cord cable
Power cord cable
,
Note
y
Do not hang onto the installed unit and
avoid any impact to the unit.
y
Secure the unit rmly to the wall so that it
does not fall o. If the unit falls o, it may
result in an injury or damage to the product.
y
When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
>
Caution
HLS36W-N0_DMARLLK_ENG_4758.indd 11 2011-02-22 �� 7:11:04
Connecting12
Connecting
2
Setting up
Pairing wireless subwoofer
LED indicator of wireless subwoofer
LED Color Status
Blue The wireless subwoofer is
receiving the signal of the unit.
Blue (blink) The wireless subwoofer is trying
to connect.
Red The Wireless subwoofer is in
standby mode.
O (No
display)
The Wireless subwoofer is
turned o.
Setting up the wireless subwoofer
for the first time
1. Connect the power cord of the Wireless
subwoofer to the outlet.
2. Turn on the main unit : The main unit and
wireless subwoofer will be automatically
connected.
Manually pairing wireless subwoofer
When your connection is not completed, you can
see the red LED on the woofer and woofer is not
made sound. To solve the problem, follow the
below steps.
1. Press and hold
I
STOP button on the unit
and MUTE button on the remote control
simultaneously.
- Displays the “REMATE”.
2. Press PAIRING on back of the woofer.
- The blue LED will icker
3. Turn o and on the unit.
- If you see “blue” LED, it’ s successful.
4. If you don’t see “blue” LED, try again Step 1 -
Step 3.
y
If you operate main unit then wireless
subwoofer (rear speakers) sound within a
few seconds in standby mode.
y
Set the distance between this unit and
subwoofer Receiver within 10 m (32 ft.).
y
Optimum performance can be
implemented only when the unit and
the Wireless subwoofer within distance
of 2 m (6 ft.) to 10 m (32 ft.) is used since
communication failure may occur if longer
distance is used.
y
It takes a few seconds (and may take longer)
for the Wireless Transmitter and subwoofer
to communicate with each other.
,
Note
HLS36W-N0_DMARLLK_ENG_4758.indd 12 2011-02-22 �� 7:11:04
Connecting 13
Connecting
2
Optional Equipment
Connection
AUDIO (PORT. IN) In
Connection
PORT.IN Connection
MP3 player, etc...
Listening to music from your
portable player
The unit can be used to play the music from many
types of portable player or external devices.
1. Connect the portable player to the
AUDIO (PORT. IN) IN connector of the unit.
2. Turn the power on by pressing
1
POWER.
3. Select the PORTABLE function by pressing
INPUT.
4. Turn on the portable player or external device
and start playing it.
OPTICAL In connection
Connect an optical output of Unit (or Digital Device
etc) to the OPTICAL IN 1/ 2 connector.
OPTICAL IN Connection
To the digital
optical output jack
of your component
Speaker ez (easy) setup
Listens to sound from TV or DVD or Digital Device
with 2.1 or 2ch mode.
1. Connect the unit’s OPTICAL IN 1/ 2 jack to jack
on optical out of your TV (or Digital Device etc.).
2. Select the OPTICAL 1/ 2 by using the OPTICAL.
To select the OPTICAL 1/ 2 directly
3. Listen to sound with 2.1 or 2ch speaker.
4. Press OPTICAL to exit from OPTICAL 1/ 2.
Function is retuned to previous one.
HLS36W-N0_DMARLLK_ENG_4758.indd 13 2011-02-22 �� 7:11:04
3 Operating
Connecting14
Connecting
2
USB Playback
Insert USB memory device to the USB port on the
front of the unit.
USB Connection
Removing the USB Device from the unit.
1.
Choose a dierent function mode or press
I
STOP twice in a row.
2. Remove the USB device from the unit.
Compatible USB Devices
y
MP3 Player : Flash type MP3 player.
y
USB Flash Drive : Devices that support USB2.0 or
USB1.1.
y
The USB function of this unit does not support
some USB devices.
USB device requirement
y
Devices which require additional program
installation connected to a computer, are not
supported.
y
Do not extract the USB device while in operation.
y
For a large capacity USB, it may take longer than
a few minutes to be searched.
y
To prevent data loss, back up all data.
y
If you use a USB extension cable or USB hub, the
USB device is not recognized.
y
Using NTFS le system is not supported. (Only
FAT(16/32) le system is supported.)
y
This unit is not supported when the total
number of les is 1 000 or more.
y
External HDD, Card readers, Locked devices,
or hard type USB devices are not supported.
y
The unit’s USB Port cannot be connected to PC.
The unit can not be used as a storage device.
HLS36W-N0_DMARLLK_ENG_4758.indd 14 2011-02-22 �� 7:11:04
Operating 15
Operating
3
Basic Operations
USB Operation
1. Connect the USB device to the USB port.
2. Select the USB function by pressing INPUT.
3. Select a le you want to play by pressing
C
or
V
.
To Do this
Stop Press
Z
Playback Press
d/M
Pause
Press
d/M
Skipping to the
next/ previous
le
During playback, press
C
or
V
to go to the next le
or to return to the beginning
of the current le.
Press
C
twice briey to
step back to the previous le.
Playing
repeatedly or
randomly
Press REPEAT on the remote
control repeatedly, the display
change in the following order,
RPT 1 RPT D (DIRECTORY)
RPT ALL RANDOM OFF.
Selecting les
directly
Press 0 to 9 numerical
buttons on the remote
control to go to the desired
le directly.
Other Operations
DOLBY DRC (Dynamic Range
Control)
Make the sound clear when the volume is turned
down (Dolby Digital only). Set to [DRC ON] by using
DOLBY DRC.
AV Sync
When receiving audio signals from TV, sound and
images may not be matched. In the case, this
function can adjust the delay time.
1. Press AV SYNC.
2. Use
C
V
to scroll up and down through
the delay amount, which you can set at
anything between 0 and 300m/sec.
HLS36W-N0_DMARLLK_ENG_4758.indd 15 2011-02-22 �� 7:11:04
Operating16
Operating
3
Sleep Timer Setting
Press SLEEP one or more times to select delay time
between 10 and 180 minutes, after the unit will
turn o.
To check the remaining time, press SLEEP.
To cancel the sleep function, press SLEEP
repeatedly until “SLEEP 10” appears, and then press
SLEEP once again while “SLEEP 10” is displayed.
You can check the remaining time before the
Unit turns o.
Press SLEEP The remaining time appears in the
display window.
,
Note
Dimmer
Press SLEEP once. The display window will be
darken by half. To cancel it, press SLEEP repeatedly
until dim o.
Turn off the sound temporarily
Press MUTE to mute your unit.
You can mute your unit in order, for example, to
answer the telephone, appearing the in the
display window.
Adjust the woofer level
settings
You can adjust the sound level of woofer.
1. Press WOOFER LEVEL.
2. Press VOLUME -/+ to adjust the sound level of
the woofer.
Displaying file and input
source
You can display various information on the USB and
OPTICAL IN 1/ 2 mode by pressing INFO..
USB : MP3/ WMA containing le information
OPTICAL IN 1/ 2 : Audio format, Audio channel
HLS36W-N0_DMARLLK_ENG_4758.indd 16 2011-02-22 �� 7:11:04
Operating 17
Operating
3
Sound adjustment
Setting the surround mode
This system has a number of pre-set surround
sound elds. You can select a desired sound mode
by using SOUND EFFECT.
The displayed items for the equalizer may be
dierent depending on sound sources and eects.
On Display Description
NATURAL
You can enjoy comfortable
and natural sound.
BYPASS
You can enjoy the sound
without equalizer eect.
BASS
The BASS is Bass Blast. During
playback, reinforce the treble,
bass and surround sound
eect.
CLRVOICE
The CLRVOICE is Clear Voice.
This program make voice
sound clear, improving the
quality of voice sound. (We
encourage to use this EQ
when you watch the movie of
5.1 channel.)
VIRTUAL
The VIRTUAL is VSM Plus.
You can enjoy more virtual
surround sound.
GAME
The GAME is Game Equalizer.
You can enjoy more virtual
sound while playing video
games.
NIGHT
The NIGHT is Night Mode.
This may be useful when you
want to watch movies at low
volume late at night.
UPSCALER
The UPSCALER is MP3 Up-
Scaling. When listening to
MP3 les or other compressed
music, you can enhance the
sound. This mode is available
only to 2 channel sources.
LOUDNESS
Improves the bass and treble
sound.
y
In some of surround modes, some speakers,
there’s no sound or low sound. It depends
on the mode of surround and the source of
audio, it is not defective.
y
You may need to reset the surround mode,
after switching the input, sometimes even
after the sound le changed.
,
Note
HLS36W-N0_DMARLLK_ENG_4758.indd 17 2011-02-22 �� 7:11:04
4 Troubleshooting
Operating18
Operating
3
Controlling a TV with
the Supplied Remote
Control
You can control your TV using the buttons below.
Button Operation
1
(TV POWER) Turn the TV on or o.
AV/INPUT
Switch the TV’s input source
between the TV and other
input sources.
VOL +/–
Adjust the volume of the
TV.
PR/CH
W/S
Scan up or down through
memorized channels.
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
,
Note
Setting up the remote to
control your TV
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
1. While holding down
1
(TV POWER) button,
and press the manufacturer code for your
TV with the numerical buttons (see the table
below).
Manufacturer Code Number
LG 1(Default), 2
Zenith 1, 3, 4
GoldStar 1, 2
Samsung 6, 7
Sony 8, 9
Hitachi 4
2. Release the
1
(TV POWER) button to complete
setting.
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may
be reset to the default setting. Set the appropriate
code number again.
HLS36W-N0_DMARLLK_ENG_4758.indd 18 2011-02-22 �� 7:11:05
4 Troubleshooting
Troubleshooting 19
Troubleshooting
4
Troubleshooting
PROBLEM CORRECTION
No Power
Plug in the power cord.
Check the condition by operating other electronic devices.
No sound
Press FUNCTION and check the selected function.
The power cord of woofer is not connected. Plug the power cord into the wall outlet
securely.
Pairing between the unit and woofer gets disconnected. Connect the unit and woofer.
(Refer to the page 12)
The remote
control does
not work
properly.
The remote control is too far from the unit.
Operate the remote control within about 23 ft (7m).
There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
The battery in the remote control is exhausted.
Replace the battery with new one.
HLS36W-N0_DMARLLK_ENG_4758.indd 19 2011-02-22 �� 7:11:05
5 Appendix
Appendix20
Appendix
5
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
y
Do not use volatile liquids such as insecticide
spray near the unit.
y
Wiping with strong pressure may damage the
surface.
y
Do not leave rubber or plastic products in
contact with the unit for a long period of time.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
HLS36W-N0_DMARLLK_ENG_4758.indd 20 2011-02-22 �� 7:11:05
La pagina si sta caricando...
La pagina si sta caricando...
La pagina si sta caricando...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
