Shindaiwa HT320S Manuale utente

1????

OPERATOR'S MANUAL

MANUEL D'UTILISATION

BEDIENUNGSANLEITUNG

MANUALE PER L'OPERATORE

MANUAL DE INSTRUCCIONES

HT320S

ENGLISH

FRANÇAIS

DEUTSCH

ITALIANO

ESPAÑOL

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE RULES FOR

SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

AVERTISSEMENT

LIRE ATTENTIVEMENT LES INSTRUCTIONS ET SUIVRE LES RÈGLES DE

SÉCURITÉ.

LE NON-RESPECT DES RÈGLES DE SÉCURITÉ ENTRAÎNE UN RISQUE DE

BLESSURE GRAVE.

WARNUNG

LESEN SIE DIE BEDIENUNGSANLEITUNG SORGFÄLTIG DURCH, UND BE-

FOLGEN SIE DIE SICHERHEITSREGELN. ANDERNFALLS BESTEHT DAS

RISIKO SCHWERER VERLETZUNGEN.

AVVERTENZA

LEGGERE E SEGUIRE ATTENTAMENTE LE ISTRUZIONI PER LAVORARE IN

CONDIZIONI DI MASSIMA SICUREZZA. LA MANCATA OSSERVANZA DELLE

ISTRUZIONI POTREBBE PROVOCARE LESIONI GRAVI.

ADVERTENCIA

LEA ATENTAMENTE LAS INSTRUCCIONES Y SIGA LAS INDICACIONES

PARA UN FUNCIONAMIENTO SEGURO. DE NO HACERLO, PODRÍA SUFRIR

LESIONES GRAVES.

??

1Top cover

ENGLISH

(Original instructions)

OPERATOR'S MANUAL

HEDGE TRIMMER

WARNING

READ THE INSTRUCTIONS CAREFULLY AND FOLLOW THE

RULES FOR SAFE OPERATION.

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY.

2

Important information

2Important information

Please ensure that you read the operator's manual before using your product.

 Intended use of this product

 shindaiwa Hedge Trimmer are lightweight, high-performance, petrol engined units designed for hedge and shrub trim-

ming.

 Do not use this unit for any purpose other than aforementioned.

 Users of the product

 You should not use this product until you have read the operator's manual carefully and fully absorbed its content.

 This product should not be used by anyone who has failed to read the operator's manual properly, is suffering from a

cold, tiredness or otherwise in poor physical condition, or children.

 Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their prop-

erty.

 About your operator's manual

 This manual contains necessary information about the operation and maintenance of your product. Please read it care-

fully and absorb its contents.

 Always keep your manual in a place where it is readily accessible.

 If you have lost your manual or it is damaged and no longer readable, please purchase a new one from your shindaiwa

dealer.

 The units used in this manual are SI units (International System of Units). Figures in parentheses are reference values,

and there may be a slight conversion error in some cases.

 Loaning or assigning your product

 When loaning the product described in this manual to another party, ensure that the person borrowing and working with

the product receives the operator's manual along with the product. If you assign your product to another party, please

enclose the operator's manual with the product when handing it over.

 Enquiries

 Please contact your shindaiwa dealer for requests regarding information about your product, the purchase of consum-

ables, repairs, and other such enquiries.

 Notices

 The content of this manual may be changed without notice for the purpose of upgrades to the product. Some of the

illustrations used may differ from the product itself in order to make the explanations clearer.

 Please consult your shindaiwa dealer if anything is unclear or of concern.

 Feature of this model: Soft Start

 Soft Start generates enough revolving power to rotate crankshaft up to a speed to ignite the engine and bring almost

no kickback. Soft Start makes engine start far easier than you ever expect.

Manufacturer

YAMABIKO CORPORATION

1-7-2 Suehirocho, Ohme, Tokyo 198-8760 JAPAN

Authorized Representative in Europe:

CERTIFICATION EXPERTS B.V.

P.O. box 5047, Merwedeweg 2, 3621 LR Breukelen, The Netherlands

3

Contents

For safe use of your product............................................................................................... 4

Warning notices............................................................................................................. 4

Other indicators ............................................................................................................. 4

Symbols.........................................................................................................................4

Location in which the safety decal is attached............................................................... 5

Handling fuel.................................................................................................................. 6

Handling the engine....................................................................................................... 7

Handling the product ..................................................................................................... 8

Packing list........................................................................................................................ 12

Description........................................................................................................................ 13

Before you start ................................................................................................................14

Preparing the fuel ........................................................................................................ 14

Engine operation............................................................................................................... 15

Starting the engine ...................................................................................................... 15

Stopping the engine..................................................................................................... 16

Hedge and shrub trimming operation ............................................................................... 17

Basic hedge trimming operation .................................................................................. 17

Maintenance and care ...................................................................................................... 18

Servicing guidelines..................................................................................................... 18

Maintenance and care ................................................................................................. 18

Storage ............................................................................................................................. 23

Long-term storage (30 days or more).......................................................................... 23

Disposal procedure........................................................................................................... 24

Specifications.................................................................................................................... 25

Declaration of conformity .................................................................................................. 26

4

For safe use of your product

For safe use of you r product

Be careful to read this section before using your product.

 The precautions described in this section contain important safety information. Please observe them carefully.

 You must also read the precautions that appear in the body of the manual itself.

Text following a [diamond mark] mark describes the potential consequences of failing to observe the precaution.

Warning notices

Situations where there is a risk of physical injury to the operator and other people are indicated in this manual and on the product

itself by the following warning notices. Always read and observe them carefully in order to ensure safe operation.

Other indicators

As well as warning notices, this manual uses the following explanatory symbols:

Symbols

In this manual and on the product itself, a series of explanatory symbols is used. Please make sure that you fully understand what

each symbol means.

DANGER WARNING CAUTION

This symbol accompanied by the

word "DANGER" calls attentions to

an act or a condition which will lead to

serious personal injury or death of op-

erators and bystanders.

This symbol accompanied by the

word "WARNING" calls attentions to

an act or a condition which can lead to

serious personal injury or death of op-

erators and bystanders.

"CAUTION" indicates a potentially

hazardous situation which, if not

avoided, may result in minor or mod-

erate injury.

Circle and slash sym-

bol means whatever is

shown is prohibited.

NOTE IMPORTANT

This enclosed message provides tips

for use, care and maintenance of the

product.

Framed text featuring the word "IM-

PORTANT" contains important infor-

mation about the use, checking,

maintenance and storage of the prod-

uct described in this manual.

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

Carefully read the operator's

manual

Petrol and oil mixture

Wear eyes, ears and head

protection

Purge bulb (Primer)

Safety / Alert Finger severing

Emergency stop

Carburettor adjustment

- Idle speed

Do not use the product in plac-

es with poor ventilation

Choke Control

"Cold Start"

Position

(Choke Closed)

5

For safe use of your product

Location in which the safety decal is attached

 The safety decal shown below has been attached to the products described in this manual. Ensure that you understand what

the decal means before using your product.

 If the decal becomes unreadable due to wear and tear or damage, or peels off and is lost, please purchase a replacement decal

from your dealer and attach it in the location shown in the illustrations below. Ensure that the decal is readable at all times.

Beware of fire

Choke Control

"Run"

Position

(Choke Open)

Beware of electric shocks

Beware of high-temperature

areas

Guaranteed sound power lev-

el

Engine start

Symbol form/shape Symbol description/applica-

tion

Symbol form/shape Symbol description/applica-

tion

1. Safety decal (Part number X505-002030)

2. Safety decal (Part number X505-002310)

6

For safe use of your product

Handling fuel

DANGER

Always keep well away from fire when refuelling

Fuel is highly inflammable and leads to a risk of fire if mishandled. Use extreme care when mixing, storing or handling

or serious personal injury may result. Be careful to observe the following instructions.

 Do not smoke or hold a flame near when refuelling.

 Do not fuel up while the engine is hot or in operation.

 If you do so, the fuel could ignite and cause fire, leading to burns.

About the container and refuelling place

 Use an approved fuel container.

 Fuel tanks/cans may be under pressure.

Always loosen fuel caps slowly allowing pressure to

equalize.

 DO NOT fill fuel tanks indoors.

ALWAYS fill fuel tanks outdoors over bare ground.

Fuel spills can cause fire

Observe the following precautions when refuelling:

 Do not add so much fuel that it reaches the mouth of the

fuel tank. Keep the fuel within the prescribed level (up to

the shoulder level of the fuel tank).

 Mop up any fuel that overflows or spills out due to over-

filling.

 Tighten the fuel tank cap securely after refuelling.

 Fuel spills can cause fire and burns when ignited.

1. Fuel tank

2. Shoulder level

Do not start the engine in the area where you refue-

led

 You must not start the engine in the place where you

carried out the refuelling. Move at least 3m from the

place where you refueled before starting the engine.

 Fuel leaks that occur while refuel-

ling can cause fire if ignited.

Fuel leaks cause fire

 After refuelling, always check

that there are no leaks or dis-

charges of fuel from the fuel

pipe, fuel system grommets, or

around the fuel tank cap.

 If you do find fuel leaks or discharges, stop using the

product immediately and contact your dealer to have it

repaired.

 Any fuel leaks could cause fire.

7

For safe use of your product

Handling the engine

WARNING

Starting the engine

Be particularly careful to observe the following precau-

tions when starting the engine:

 Always ensure all handles and guards are fitted

 Check that none of the nuts and bolts are loose

 Check that there are no fuel leaks

 Check that the cutter blades is not damaged or exces-

sively worn. If you find any abnormalities, do not use

the product.

 Place the product in a flat, well ventilated place

 Leave plenty of space around the product and do not al-

low people or animals near it

 Remove obstructions, if any

 Make sure that the cutter blades is not touching the

ground or any obstacles

 Start the engine with the throttle trigger in the idle speed

position

 Hold the product firmly to the ground when starting the

engine

 Do not start the engine holding the product in the air

 Failure to observe the precautions could cause an accident

or injury, or even lead to a fatality.

Once the engine has started, check for abnormal vi-

brations and sounds

 Check that there are no abnormal vibrations or sounds

once the engine starts. Do not use the product if there

are abnormal vibrations or sounds. Contact your dealer

to have it repaired.

 Accidents involving parts that fall or shatter off can cause

wounds or serious injury.

Do not touch high temperature or high voltage com-

ponents while the product is running

Do not touch the following high temperature or high volt-

age components while the product is running or for some

time after it stops.

 Silencer, spark plug, gear housing, and

other high temperature components

 You could burn yourself if you touch a high

temperature component.

 Spark plug, spark plug wire, and other

high voltage components

 You could receive an electric shock if you

touch a high voltage component while the

product is running.

Put safety first in the case of fire or smoke

 If fire comes from the engine or smoke appears from

any area other than the exhaust vent, first distance

yourself from the product to ensure your physical safe-

ty.

 Use a shovel to throw sand or other such

material on the fire to prevent it from

spreading, or put it out with a fire extin-

guisher.

 A panicked reaction could result in the fire and

other damage becoming more extensive.

Exhaust fumes are toxic

 The exhaust fumes from the engine contain toxic gases.

Do not operate the product indoors or in a plastic green-

house or in other ill ventilated places.

 The exhaust fumes could cause poisoning.

Turn off the engine when checking or maintaining

the product

Observe the following precautions when checking and

maintaining your product after use:

 Turn the engine off and do not attempt to check or main-

tain the product until the engine has cooled

 You could burn yourself.

 Remove the spark plug cap before performing checks

and maintenance

 An accident could occur if the product starts unexpectedly.

Checking the spark plug

Observe the following precautions when checking the

spark plug.

 If the electrodes or terminals are worn, or if there are

cracks in the ceramics, replace them with new parts.

 The spark test (for checking whether the spark plug is

sparking) must be carried out by your dealer.

 The spark test must not be carried out in proximity of

the spark plug hole.

 The spark test must not be performed in places where

there are fuel spills or inflammable gases

 You must not touch the

metal parts of the spark

plug

 The spark plug could ig-

nite a fire or give you an

electric shock.

8

For safe use of your product

Handling the product

General precautions

Precautions for use

WARNING

Operator's manual

 Be careful to read the operator's manual

properly before using your product in or-

der to ensure correct operation.

 Failure to do so could lead to an accident or

serious injury.

Do not use the product for anything

other than its intended purpose

 You must not use the product for any purpose other

than those described in the operator's manual.

 To do so could lead to an accident or serious injury.

Do not modify the product

 You must not modify the product.

 To do so could lead to an accident or serious injury. Any

malfunction resulting from a modification to the product will

not be covered by the manufacturer's warranty.

Do not use the product unless it has been checked

and maintained

 You must not use the product unless it has been

checked and maintained. Always ensure that the prod-

uct is checked and maintained on a regular basis.

 Failure to do so could lead to an accident or serious injury.

Loaning or assigning your product

 When loaning your product to another party, ensure

that the person borrowing the product receives the op-

erator's manual along with it.

 If you assign your product to another party, please en-

close the operator's manual with the product when

handing it over.

 Failure to do so could lead to an accident or serious injury.

Being prepared in case of an injury

In the unlikely event of an accident or injury, please ensure

that you are prepared.

 First aid kit

 Towels and wipes (to stop any bleeding)

 Whistle or mobile phone (for calling outside help)

 If you are unable to perform first aid or call for outside help,

the injury could worsen.

DANGER

Starting the engine

 Never try to start the engine by positioning yourself on

the blade side.

 Physical injury can occur if the cutter blades suddenly starts

to move.

Always stop the engine when a blades jam occurs

 Do not attempt to remove an object causing a blades

jam if the engine is running.

 Physical injury can occur if a blades jam is removed and the

blades starts moving.

9

For safe use of your product

WARNING

Users of the product

The product should not be used by:

 people who are tired

 people who have taken alcohol

 people who are on medication

 people who are pregnant

 people who are in poor physical

condition

 people who have not read the op-

erator's manual

 children

 Failure to observe these instruc-

tions could lead to an accident.

 The ignition system of this product generates electro-

magnetic fields during operation. Magnetic fields can

cause pacemaker interference or pacemaker failure. To

reduce health risks, we recommend that pacemaker us-

ers consult their physician and the pacemaker manu-

facturer before operating this product.

Environment of use and operation

 Do not use the product in places where there is no sure

foothold, such as on steep slopes or after rainfall, as

such places are slippery and dangerous.

 Do not operate the product at night or in dark places

with poor visibility.

 A serious injury could result if you fall or slip, or fail to oper-

ate the product correctly.

Transport of the product

When transporting in the situations described below, turn

off the engine and ensure that the cutter blades has

stopped moving, then fit the blade cover and position the

silencer away from yourself.

 Moving to the place where you are working

 Moving to another area while you are working

 Leaving the place where you have been working

 Failure to observe these precautions could cause burns or

serious injury.

 When transporting the product by car, empty the fuel

tank, fit the blade cover, and secure the product firmly

in place to prevent it from moving around.

 Travelling by car with fuel in the fuel tank could lead to a fire.

Vibration and cold

It is believed that a condition called Raynaud's Phenome-

non which affects the fingers of certain individuals may be

brought about by exposure to vibration and cold. Expo-

sure to vibration and cold may cause tingling and burning,

followed by loss of colour and numbness in the fingers.

The following precautions are strongly recommended be-

cause the minimum exposure which might trigger the ail-

ment is unknown.

 Keep your body warm, especially the head and neck,

feet and ankles, and hands and wrists.

 Maintain good blood circulation by performing vigorous

arm exercises during frequent work breaks, and also by

not smoking.

 Limit the number of hours of operation.

Try to fill each day with jobs where operating the hedge

trimmer or other hand-held power equipment is not re-

quired.

 If you experience discomfort redness and swelling of

the fingers, followed by whitening and loss of feeling,

consult your physician before exposing yourself further

to cold and vibration.

 Failure to observe these instructions could result in damage

to your health.

Repetitive stress injuries

It is believed that over-using the muscles and tendons of

the fingers, hands, arms and shoulders may cause sore-

ness, swelling, numbness, weakness and extreme pain to

the areas just mentioned. Certain repetitive hand activities

may put you at a high risk for developing a repetitive

stress injury (RSI).

To reduce the risk of RSI, do the following:

 Avoid using your wrist in a bent, extended or twisted

position.

 Take periodic breaks to minimize repetition and rest

your hands. Reduce the speed and force in which you

do the repetitive movement.

 Do exercises to strengthen hand and arm muscles.

 See a doctor if you feel tingling, numbness or pain in

your fingers, hands, wrists or arms. The sooner RSI is

diagnosed, the more likely permanent nerve and muscle

damage can be prevented.

 Failure to observe these instructions could result in damage

to your health.

10

For safe use of your product

WARNING

Remove foreign objects and obstructions before

working with the product

 Inspect area that the product will be used in. Remove

stones, metal objects and any other object that could

jam or damage the product.

 An accident or serious injury can occur if foreign objects

throw the cutting device.

Turn off the engine immediately if anything goes

wrong

In the following situations, turn off the engine immediately

and ensure that the cutting device has stopped before

checking each area of the product. Replace any damaged

parts.

 If the cutting device hits a rock, tree, post, or other such

obstruction while you work.

 If the product suddenly starts to vibrate abnormally.

 Continuing to use parts when they are damaged could lead

to an accident or serious injury.

The area within a 10 m radius is a danger zone

The area within a 10 m radius of the product is a danger

zone. Be careful to observe the following precautions

while working with the product.

 Do not allow children and other people or pets to enter

the danger zone.

 If another person enters the danger zone, turn off the

engine to stop the blades.

 When approaching the operator, signal to him by, for

example, throwing twigs from outside the danger zone,

and then check that engine has been switched off and

the blades has stopped moving.

 Do not allow anyone to hold the material you are cut-

ting.

 Any contact with the cutter blades could cause serious inju-

ry.

Do not use the product when the cutter blades is

moving at idle speed

 You must not use the product while the cutter blades is

moving if the Hedge Trimmer is running with the throttle

trigger in the idle speed position. Turn off the engine im-

mediately and adjust the carburettor.

 To do so could lead to an accident or serious injury.

Do not operate the product one-handed

 Keep both hands on handles while the engine is run-

ning. Never operate the product with only one hand.

 Keep a firm grip on the hedge trimmer with both hands,

one hand on the front handle, the other hand on the rear

handle.

 Use a firm grip with thumbs and fingers encircling the

handles.

 Never remove hands from the product when the blades

are moving.

 Failure to observe these instructions will cause the product

to be held unsteadily and could result in serious injury.

Make sure that the cutter blades is stopped before

putting the product on the ground

 When you turn off the engine, check to ensure the cutter

blades has stopped moving before you lower the prod-

uct to the ground.

 Even if the engine has been turned off, the blades can still

cause an injury while free-wheeling.

Remove debris from the silencer

 If objects such as grasses, leaves, twigs or excessive

grease got stuck over the area around the silencer of

the engine, stop the engine and remove them paying at-

tention not to touch hot spots.

 Failure to do so could lead to a fire.

11

For safe use of your product

Protective gear

WARNING

Do not use the product to cut hard objects

 Do not use the product to cut hard objects such as

wires or steel plates.

 If the blades strikes an obstruction or is prevented from

functioning properly, stop the engine and inspect the

blades for damage.

 Failure to follow these instructions could cause breakage of

the product or an accident.

Never use the product getting on a ladder or a stool

 Do not overreach or stand on unstable surfaces.

 Do not use the product when being at the top of the lad-

der or standing on a stool.

 Failure to do so could lead to an accident or serious injury.

WARNING

Wear protective gear

Always wear the following protective gear when working

with the hedge trimmer.

a Head protection (helmet): Protects the head

b Ear muffs or ear plugs: Protect the hearing

c Safety goggles: Protect the eyes

d Safety gloves: Protect the hands from cold and vibration

e Work clothes that fit (long sleeves, long trousers): Pro-

tect the body

f Heavy duty, non-slip protective boots or non-slip work

shoes : Protect the feet

 Failure to observe these precautions could result in damage

to your sight or hearing, or lead to a serious injury.

When necessary, please use the protective gear below.

 Dust mask: Protects the breathing apparatus

 Bee net: To deal with attacks by bees

Wear proper clothing

Do not wear ties, jewellery, or loose, dangling clothing which could be

caught in the unit. Do not wear open toed footwear, or go bare-foot or

barelegged.

 Failure to observe these precautions could result in damage to your sight or

hearing, or lead to a serious injury.

12

Packing list

 The following parts are packed separately in the packing box.

 When you have unpacked the box, please check the parts that it contains.

 Contact your dealer if anything is missing or broken.

Number Part name Quantity

(1) Hedge trimmer assembly 1

(2) Blade cover 1

(3) Operator's manual 1

(4) T-wrench 1

13

Description

Descript ion

1. Spark plug

2. Silencer cover Cover for the silencer to prevent opera-

tor contact with hot exhaust.

3. Carburettor Device for mixing fuel and air in the correct

proportions.

4. Starter handle Pull handle to start the engine.

5. Throttle trigger lockout Device that prevents the acci-

dental operation of the throttle trigger until manually re-

leased.

6. Ignition switch Device for allowing the engine to be

started and stopped.

7. Throttle trigger Device activated by the operator's fin-

ger, for controlling the engine speed.

8. Rear handle Handle located furthest from the cutting

device.

9. Fuel tank cap For closing the fuel tank.

10. Fuel tank Contains fuel and fuel filter.

11. Air cleaner cover Covers air filter.

12. Gear housing Housing to support the gears that reduce

the speed of engine to cutting attachment.

13. Front handle Handle located on the cutting device.

14. Guard Guard between the front handle and cutting de-

vice for protecting the hand from injuries if the hand slips

off the handle.

15. Cutting device That part of the assembly of cutter

blade and shear plate together with any supporting part,

which performs the cutting action.

16. Leaf collector plate Keeps cut leaves or twigs from

scattering.

17. Blade cover When transporting or storing the product

always fit the blade cover.

18. Type and serial number

14

Before you start

Preparing the fuel

Fuel

 Fuel is a mixture of regular grade petrol and an air-cooled 2-

stroke engine oil.

Minimum 89 Octane unleaded petrol is recommended. Do not

use fuel containing methyl alcohol or more than 10 % of ethyl

alcohol.

 Recommended mixture ratio; 50 : 1 (2 %) for ISO-L-EGD

Standard (ISO/CD 13738), JASO FC, FD grade and Shindai-

wa recommended oil.

- Never use two-stroke oil intended for water-cooled engines,

motor-cycle engines.

- Do not mix directly in engine fuel tank.

- Avoid spilling petrol or oil. Spilled fuel should always be

wiped up.

- Handle petrol with care, it is highly inflammable.

- Always store fuel in approved container.

Fuel supply

 Fill the fuel tank outdoors over bare ground and install the fuel

cap securely. Do not pour fuel indoors.

 Place the product and the refuelling tank on the ground when

performing the refuelling operation. Do not refuel the product

on the loading platform of a truck, or in other such places.

 Always ensure that the fuel level remains below the shoulder

level of the fuel tank when refuelling.

 There is a difference in pressure between the fuel tank and the

outside air. When refuelling, loosen the fuel tank cap slightly to

eliminate the difference in pressure.

 Always wipe up any fuel spills.

 Move at least 3m away from where you refueled before you

start the engine.

 Keep the refuelling tank in a shaded area away from fire.

DANGER

 Fuel is highly inflammable and there is a risk of fire if it is handled incorrectly. Carefully read and ob-

serve the precautions in the section of this manual titled "For safe use of your product".

 Once the refuelling is complete, securely tighten the fuel tank cap and do not forget to check that there

are no leaks or discharges of fuel from the fuel pipe, fuel system grommets, or around the fuel tank

cap. If you do find fuel leaks or discharges, stop using the product immediately and contact your deal-

er to have it repaired.

 If the fuel ignites, it could cause burns and fire.

CAUTION

There is difference in pressure between the fuel tank and the outside air. When refuelling, loosen the fuel tank cap

slightly to eliminate the difference in pressure.

 Otherwise, fuel may get spewed.

NOTE

Stored fuel ages. Do not mix more fuel than you expect use in thirty (30) days. Do not mix directly in fuel tank.

1. Fuel tank 2. Shoulder level

15

Engine operation

Starting the engine

Starting a cold engine

(Connect the spark plug cap if the product has been in storage for

a long period of time)

The starting procedure depends on whether the engine is cold or

warm. A cold engine is started as follows.

1. Remove the blade cover and check the cutter blades. If an-

ything is wrong, replace it with a new one.

2. Placing the product on level ground, check to ensure that the

blades does not come into contact with the surface of the

ground or any other impediment using a beam or other such

implement.

3. Check that there are no fuel leaks.

4. Move the ignition switch to the Start position.

5. Move the choke lever to the "Cold Start" position.

6. Alternately press and release the purge bulb until the fuel is

sucked up into it.

7. Checking that the area around you is safe, hold the front

handle firmly with your right hand as shown in the illustration,

pulling several times on the starter grip.

8. If you hear an explosion-like sound and the engine stops im-

mediately, move the choke lever to the "Run" position and

continue pulling on the starter grip to start the engine.

9. If the engine starts immediately when you carry out the in-

structions in step 7, above, return the choke lever gently to

the "Run" position.

10. Leave the engine to warm up at idle speed for a while.

11. Depress the throttle trigger lockout and gradually squeeze

the throttle trigger.

WARNING

 When starting the engine, observe the precautions described from Page 4 in the section "For safe use of your prod-

uct" to ensure that you operate the product correctly.

 If the cutter blade moves even though the throttle trigger is in the idle speed position when the engine is started,

adjust the carburettor before using the product.

 Cutter blade will start moving as engine attains clutch engagement speed.

 Failure to observe the precautions could cause an accident or injury, or even lead to a fatality.

NOTE

 Pull out the starter grip gently at first, and then more rapidly. Do not pull the starter rope out to more than 2/3 of its length.

 Do not let go of the starter grip as it returns.

1. Ignition switch

2. Throttle trigger

3. Throttle trigger lockout

1. Choke lever

2. Purge bulb

3. Cold Start

4. Run

1. Starter handle

16

Engine operation

Engine warm-up

1. Once the engine starts, allow it to warm up for 2 to 3 minutes

at idling (i.e. low speed).

2. Warming the engine helps to lubricate its internal workings

more smoothly. Allow the engine to warm up fully, especially

when it is cold.

Starting a warm engine

1. Move the ignition switch away from the Stop position.

2. Make sure that the throttle trigger is at the idle speed posi-

tion.

3. Check that the choke lever is in the "Run" position.

4. If fuel tank is not empty, pull on the starter grip to start the

engine.

5. If no fuel is visible in the purge bulb, alternately press and re-

lease the purge bulb until the fuel is sucked up into it.

6. Checking that the area around you is safe and pull on the

starter grip to start the engine.

Stopping the engine

1. Release the throttle trigger and set the engine to idling (i.e.

low speed).

2. Move the ignition switch to the Stop position.

3. In the event of an emergency, stop the engine immediately

using the ignition switch.

4. If the engine fails to stop, move the choke lever to the "Cold

Start" position. The engine will stall and come to a halt (a

choke stop).

∗ If the engine fails to stop when the ignition switch is used, have

the ignition switch checked and repaired by your dealer before

you use the product again.

1. Ignition switch

2. Throttle trigger

3. Throttle trigger lockout

1. Choke lever

2. Purge bulb

3. Cold Start

4. Run

1. Ignition switch

2. Throttle trigger

3. Stop

17

Hedge and shrub trimming operation

Hedge and sh rub trimming ope ration

Basic hedge trimming operation

 Pulling the throttle trigger after the engine is started will cause

the engine speed to rise and the cutter blades to start moving.

Adjust the engine speed depending on, for example, the

amount of the hedges to be cut.

 Conduct cutting work with the cutter blades positioned away

from you. Do not orient the cutter blades toward yourself or put

it closer to yourself.

 When cutting the top of the hedges or shrubs, do so by moving

the cutter blades from side to side. Tidy trimming will be made

possible by moving the blades slightly cast down.

 When cutting sides, do so by moving the cutter blades in the

bottom-up direction for tidy trimming.

 Do not press the cutter blades against the objects like trees.

Operate the product in accordance with the movement and the

speed of the cutter blades.

NOTE

 This product is designed to cut shrubs and hedges with branches no larger than 6 mm in diameter.

 When starting to trim, run the engine at full throttle. Cutting at less at than full speed can damage the clutch by allowing it to

slip. When you do not conduct trimming or cutting work, do not run the engine at full throttle.

1. Throttle trigger

2. High speed

3. Idling

18

Maintenance and care

Maintenan ce and care

Servicing guidelines

Maintenance and care

Cleaning air filter

1. Close choke. Loosen cleaner cover knob and remove air

cleaner cover and air filter.

2. Carefully brush dirt from filter or clean with a nonflammable

solvent if necessary. Dry it completely before installation.

3. Reinstall air filter with cover, after installing air filter to cover.

Cleaning fuel filter

1. Pick up fuel filter through fuel tank opening with a piece of

steel wire or the like.

2. Clean filter in a suitable cleaner or replace it if necessary.

3. Reinstall the filter.

Area Maintenance Page Before use Monthly

Air filter Clean/Replace 18 •

Fuel filter Inspect/Clean/Replace 18 •

Spark plug Inspect/Clean/Adjust/Replace 20 •

Carburettor Adjust/Replace and adjust 19 •

Cooling system Inspect/Clean 19 •

Silencer Inspect/Tighten/Clean 19 •

Gear housing Grease 21 • (18h)

Starter Inspect 22 •

Blades Inspect/Clean/Lubricate 20 •

Fuel system Inspect 20 •

Screws, bolts and nuts Inspect/Tighten/Replace - •

IMPORTANT

Time intervals are maximum. Actual use and your experience will determine the frequency of required maintenance. Record

dates of monthly and yearly inspections.

If you have any questions or problems, please contact your dealer.

1. Air filter

2. Air cleaner cover

3. Cleaner cover knob

NOTE

 If filter is excessively dirty or no longer fits properly, replace

it.

 Ensure that the filter is completely dry before reinstalling it.

1. Fuel filter

La pagina sta caricando ...

Shindaiwa HT320S Manuale utente

Shindaiwa HT320S Manuale utente

in altre lingue

Documenti correlati

Altri documenti