Moog QView QFDPT2-70NA Installation And Operation Instructions Manual

Moog Inc.

Sensor and Surveillance Systems

3650 Woodhead Drive Northbrook, IL. USA 60062

+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com

Installation and Operation Instructions

Before attempting to connect or operate this product, please

read these instructions completely.

QFD

QView™ FusionDome Multiple Camera System

QFDPT2-70NA........... Standard 7” outdoor, pendant mount, tinted dome, with (2) day / night cameras, 3-9mm auto-iris lens

QFDPT4-70NA........... Standard 7” outdoor, pendant mount, tinted dome, with (4) day / night cameras, 3-9mm auto-iris lens

IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS

UNPACKING

SERVICE

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with damp cloth.

7 Do not block any of the ventilation openings. Install in accordance with the

manufacturers instructions.

8 Cable Runs- All cable runs must be within permissible distance.

9 Mounting - This unit must be properly and securely mounted to a supporting

structure capable of sustaining the weight of the unit.

Accordingly:

a. This installation should be made by a qualied service person and should conform

to all local codes.

b. Care should be exercised to select suitable hardware to install the unit, taking into

account both the composition of the mounting surface and the weight of the unit.

10 Do not install near any heat sources such as radiators, heat registers, stoves, or other

apparatus ( including ampliers) that produce heat.

11 Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third

prong are provided for your safety. When the provided plug does not t into your

outlet, consult an electrician for replacement of the obsolete outlet.

12 Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

13 Only use attachment/ accessories specied by the manufacturer.

14 Use only with a cart, stand, tripod, bracket, or table specied by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/

apparatus combination to avoid injury from tip-over.

15 Unplug this apparatus during lighting storms or when unused for long periods of time.

16 Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled of objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Be sure to periodically examine the unit and the supporting structure to make sure that the integrity

of the installation is intact. Failure to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages or injury to anyone or anything struck

by the falling unit.

Unpack carefully. Electronic components can be

damaged if improperly handled or dropped. If an item

appears to have been damaged in shipment, replace

it properly in its carton and notify the shipper.

Be sure to save:

1 The shipping carton and packaging material.

They are the safest material in which to make future

shipments of the equipment.

2 These Installation and Operating Instructions.

If technical support or service is needed, contact us at

the following number:

The lightning ash with an arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of non-insulated

“dangerous voltage” within the product’s

enclosure that may be of sufcient magnitude

to constitute a risk to persons.

Este símbolo se piensa para alertar al usuario a la presencia

del “voltaje peligroso no-aisIado” dentro del recinto de los

productos que puede ser un riesgo de choque eléctrico.

Ce symbole est prévu pour alerter I’utilisateur à la presence

“de la tension dangereuse” non-isolée dans la clôture de

produits qui peut être un risque de choc électrique.

Dieses Symbol soll den Benutzer zum Vorhandensein der

nicht-lsolier “Gefährdungsspannung” innerhalb der

Produkteinschließung alarmieren die eine Gefahr des

elektrischen Schlages sein kann.

Este símbolo é pretendido alertar o usuário à presença “di

tensão perigosa non-isolada” dentro do cerco dos produtos

que pode ser um risco de choque elétrico.

Questo simbolo è inteso per avvertire I’utente alla presenza

“di tensione pericolosa” non-isolata all’interno della

recinzione dei prodotti che può essere un rischio di scossa

elettrica

.

The exclamation point within an equilateral

triangle is intended to alert the user to

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Este símbolo del punto del exclamation se piensa para

alertar al usuario a la presencia de instrucciones importantes

en la literatura que acompaña la aplicación.

Ce symbole de point d’exclamation est prévu pour alerter

l’utilisateur à la presence des instructions importantes dans

la littérature accompagnant l’appareil.

Dieses Ausruf Punktsymbol soll den Benutzer zum

Vorhandensein de wichtigen Anweisungen in der Literatur

alarmieren, die das Gerät begleitet.

Este símbolo do ponto do exclamation é pretendido alertar o

usuário à presença de instruções importantes na literatura

que acompanha o dispositivo.

Questo simbolo del punto del exclamaton è inteso per

avvertire l’utente alla presenza delle istruzioni importanti nella

letteratura che accompagna l'apparecchio.

TECHNICAL SUPPORT

AVAILABLE 24 HOURS

1- 800-554 -1124

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER ( OR BACK). NO USER- SERVICE-

ABLE PARTS INSIDE. REFER SEVICING

TO QUALIFIED SERVICE PERSONNEL.

MADEIN

BUY AMERICA COMPLIANT • COUNTRY OF ORIGIN U.S.A.

USA

Product Warranty Registration

Register Your Products Online

www.moogS3.com/technical-support/product-registration

Moog values your patronage. We are solely committed to providing you with the highest quality products and

superior customer service. With 3-Year and 5-Year warranties (depending on the product purchased) we stand

behind every product we sell.

:

• Simple and Trouble-Free RMA process

• Product / software updates

• Special promotions

• Eliminate the need to archive purchase documents such as receipts, purchase orders, etc.

See full warranty details at www.moogS3.com/technical-support/warranty-plan/

Limited Warranty for Moog Products

Moog - Decatur Operations, subsequently referred to as “Manufacturer,” warrants these products to be free from defects in material or workmanship as follows:

During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Manufacturer at Moog Decatur

Operations, 2525 Park Central Boulevard, Decatur, Georgia, 30035. The Product to be repaired is to be returned in either its original carton or a similar package affording

an equal degree of protection with a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our

Technical Support Team at 800.554.1124, extension 101. Manufacturer will return the repaired product freight prepaid to Purchaser. Manufacturer is not obligated to

provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.

The limited warranty stated in these product instructions is subject to all of the following terms and conditions.

TERMS AND CONDITIONS

1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an explanation

of the claim shall be given promptly by Purchaser to Manufacturer. All claims for warranty service must be made within the warranty period. If after investigation,

Manufacturer determines the reported problem was not covered by the warranty, Purchaser shall pay Manufacturer for the cost of investigating the problem at its then

prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period of the entire Product. The specic warranty on

the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the remaining period of the Product parts warranty,

whichever is greater.

2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Manufacturer’s sole obligation is to supply (or pay for) all labor necessary to repair any Product

found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.

3. EXCEPTIONS TO LIMITED WARRANTY: Manufacturer shall have no liability or obligation to Purchaser with respect to any Product requiring service during the warranty

period which is subjected to any of the following: abuse, improper use, negligence, accident, or acts of God (i.e., hurricanes, earthquakes), modication, failure of the

end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance procedures recommended by the International Security

Industry Organization, written in product instructions, or recommended in the service manual for the Product. Furthermore, Manufacturer shall have no liability where a

schedule is specied for regular replacement or maintenance or cleaning of certain parts (based on usage) and the end-user has failed to follow such schedule; attempted

repair by non-qualied personnel; operation of the Product outside of the published environmental and electrical parameters, or if such Product’s original identication

(trademark, serial number) markings have been defaced, altered, or removed. Manufacturer excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS

and excludes used Products which have not been sold by Manufacturer to the Purchaser. All software and accompanying documentation furnished with, or as part of the

Product is furnished “AS IS” (i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with

the Product. ANY COST ASSOCIATED WITH REMOVAL OF DEFECTIVE PRODUCT AND INSTALLATION OF REPLACEMENT PRODUCT IS NOT INCLUDED IN THIS WARRANTY.

4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.

PRODUCT CATEGORY PARTS \ LABOR

All Enclosures and Electronics Five (5) Years

Accessory Brackets Five (5) Years

Controllers Three (3) Years

Power Supplies / IR Illuminators Three (3) Years

Poles / PolEvators™ / CamEvator Three (3) Years

Warrior Series™ / Q-View™Three (3) Years

SView Series™Three (3) Years 6 months if used in auto scan / tour operation

DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™Three (3) Years 6 months if used in auto scan / tour operation

EXO Series™ Dome and Fixed Camera Systems* Three (3) Years 6 months if used in auto scan / tour operation

EXO Series™ GeminEye Visible and Thermal Camera Systems One (1) Year

DISCLAIMER OF WARRANTY

EXCEPT FOR THE FOREGOING WARRANTIES, MANUFACTURER HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT

NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY WARRANTY WITH REGARD TO ANY

CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE.

MANUFACTURER HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-MANUFACTURER

PRODUCTS OR NON-MANUFACTURER RECOMMENDED PRODUCTS PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.

LIMITATION OF LIABILITY

THE LIABILITY OF Manufacturer, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER, REGARDLESS

OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL PURCHASE PRICE OF THE PRODUCT WITH RESPECT

TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL MANUFACTURER BE LIABLE TO PURCHASER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL

DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION, REPLACEMENT LABOR COSTS, REIMBURSEMENT, OR DAMAGES ON ACCOUNT OF THE LOSS

OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

* NOTE

Moog will repair or replace, at its option, any equipment which is damaged by transient voltage surge/spike or lightning strike (an “Occurrence”), while properly connected

to wired AC power line with protective ground. Any repair or modication of the equipment done by someone other than Moog voids the warranty.

Form 500-911 081913

!

ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):

Power 24Vac, Class 2 Only

26 watts at 24Vac (accessories)

Heater: 25 watts

Blower: .84 watts

Input Connectors (outdoor units):

BNC Connectors - 1 for each camera

Screw-down connectors - 2

NOTE: This unit is designed for operation in an upright position. In

stalling the FusionDome™ upside down may cause damage

to the internal equipment, and will void the warranty.

CAMERAS VOLTAGE CURRENT POWER

1 24 Vac/Vdc 102mA 2.5W

2 24 Vac/Vdc 210mA 5W

3 24 Vac/Vdc 331mA 7.9W

4 24 Vac/Vdc 487mA 10.9W

Use the formula below to select the correct power supply for cameras connected

in parallel (positive to positive, negative to negative):

Total current for a 24 Vac system:

TOTAL CURRENT = (202mA x total number of cameras)

Note: 202mA is camera plus power supply

CABLE AND POWER GUIDELINES (Detailed info on Page 12)

This chart shows the proper current needed for power supplies for QView™

cameras. Use Class 2 Power only. Input voltage must be 24 Vac/Vdc.

GENERAL INSTRUCTIONS:

Tools Required: .100" Flat Head Screwdriver, Phillips Head Screwdriver

Carefully remove the housing from the packaging material. Check to be sure all parts

are present.

TABLE OF CONTENTS

Cable and Power Guidelines 4, 11

Pendant Mounting 4

Wiring 4

Camera Adjustment 5

Camera Focusing 5

Camera Settings 6, 7

NVT Instructions 8

Exploded View 10

Warranty Information 3

PENDANT MOUNTING THE QFD

1. This unit includes a 1½" NPT housing coupling that can be used with a standard

1½" NPT pipe or with brackets designed with 1½" male pipe threads, such as the

Moog WM20G.

2. Attach the coupling to the bracket or pendant pipe (Figure 1).

NOTE: Pipe threads should be clean and rust free. Use a sealer (such as Teon™

tape or silicone sealer) on the threads for outdoor applications.

Be sure the bracket is properly and securely mounted to a supporting

structure capable of rigidly holding the weight of the entire unit.

Figure 1

Add thread seal-

ing tape

Figure 2

Twist and

Secure

3. Bring all wiring through the NPT pipe or bracket.

4. Mount the housing assembly to the mounting bracket and housing coupling. A

safety cable is included with the housing to temporarily hold it while making wiring

connections. Loop the safety cable over one of the set screws on the housing coupling

(Figure 2).

5. Make the proper connections to the incoming power (See Wiring section below) and

attach all BNC connectors to the video in.

6. Place the nished wiring inside the pendant pipe. Undo the safety cable and twist

the housing onto the housing coupling. Secure all (3) setscrews provided on the

housing coupling (Figure 2 above).

WIRING

1. Attach the incoming power and accessory wiring using the color code chart below.

1 Camera Power (24 Vac) Red

2 Camera Power (24 Vac) Orange

3 Accessory Power (24 Vac) Yellow

4 Accessory Power (24 Vac) Green

NOTE: Polarity is not important in this unit.

CAMERA ADJUSTMENT

1. Access the cameras by removing the dome. Loosen the locking screws on the lip of the dome. DO NOT TAKE THESE SCREWS OUT. Once the screws are loosened, turn the

dome counter clock-wise until it stops, then pull the dome off (Figure 3).

Loosen screws only, do

not remove

Figure 3

Remove dome by twisting

counterclockwise

CAMERA FOCUSING (FOR EACH CAMERA)

Fixed Lens: Loosen the set screw in the lens mount. Manually rotate the lens until a clear picture is achieved. Once the focus is set, retighten the set screw (Figure 4).

Figure 4

Set screw

Fixed lens

Auto Iris Lens:

NOTE: THE AUTO IRIS LENS IS SET AT THE FACTORY.

• IF YOU EXPERIENCE VIDEO TOO LIGHT OR DARK AUTO IRIS ADJUSTMENT MAY BE NEEDED.

Vari-Focal Lens: First, adjust the Magnication Lock Screw to the desired magnication (telephoto to wide angle). Tighten the Lock Screw. Next, adjust the Focus Lock Screw

until a clear picture is achieved. Tighten the Lock Screw (Figure 5).

Figure 5

Magnication lock

screw

Focus lock

screw

Fixed iris

vari-focal lens

Included with every camera is an On Screen Display

(OSD) controller.

Included with every camera is an On Screen Display

(OSD) controller.

In order to make any change to the camera setting

you must rst connect the OSD controller to the

camera. Note the camera must be powered in order

to access menus.

Controller

Use the Multi Tact Switch within the camera

Direction and Enter Guide

Camera

Connection

Follow the steps listed below to gain access and modify the camera settings

LT RT

UP

DN

OSD

CONTROLLER

LT RT

UP

DN

Left

Down

Right

Up Enter

OSD MENU FUNCTION

LENS DC MANUAL

EXPOSURE SHUTTER BRIGHTNESS AGC DWDR

WHITE BAL ATW1 ATW2 AWC -> SET MANUAL

BACKLIGHT OFF BLC HLC

DAY & NIGHT AUTO COLOR B/W EXT

SPECIAL CAM TITLE MOTION PRIVacY IMAGE ADJ

DPC LANGUAGE VERSION

RESET FACTORY

EXIT

* START SET UP MENU

1) LENS

Press the Middle Multi Tact Switch,

the main setup menu is displayed on the monitor screen

Turn the Switch toward Left or Right side, Select DC or MANUAL

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & nIGHT AUTO

SPECIAL

RESET

EXIT

Select the function

by using the switch

* Simply make the

adjustment in the

following order to help

make the focusing

easier:

- Select MANUAL

- Adjust lens focus well

- Then return to DC

* A function with

the icon has

sub menus. To

select a sub

menu, select a

function with the

icon and press

the switch

Down

Up

Enter

Left Right

MANUAL

2) EXPOSURE

NTSC: 1/60, PAL: 1/50

FLK

1/250 - 1/100,000

*darker brighter

Attention BRIGHTNESS adjusts DC

level of the lens

255

ON - 000 - 063

SHUTTER

BRIGHTNESS

DWDR

SHUTTER AUTO

BRIGHTNESS 000

DWDR OFF

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

255

013

008

005

3) WHITE BALANCE

BLUE 000

RED 000

255

ATW1 (wider range)

ATW2 (narrower range)

AWC -> SET

MANUAL

WB MANUAL

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

INDOOR

OUTDOOR

MANUAL

255

009

AREA 2

NIGHT ONLY

010

011

010

OFF

4) BACKLIGHT

Attention When select BLC,

AREA 1 always turns on

BLC

HLC

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

AREA SEL. AREA 1

AREA STATE ON

GRIN 000

HEIGHT 000

WIDTH 000

LEFT/RIGHT 000

TOP/BOTTOM 000

LEVEL 000

MODE ALL DAY

OFF

ON

LOW

5) DAY & NIGHT

WARNING Do not change

the above factory-set levels

*DDN *TDN

AUTO

BW

EXIT

COLOR

IR GRAIN 000

WIDTH 000

HEIGHT 000

LEFT/RIGHT 000

TOP/BOTTOM 000-009

D -> N LEVEL 040-224 140-224

D -> N DELAY 1 SEC - 60SEC

N -> D LEVEL 000-184 000084

N -> D DELAY 1 SEC - 60SEC

BURST ON

IR SMART OFF

IR LEVEL HIGH

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

7) RESET & EXIT

FACTORY RESET

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

ON

* DEAD PIXEL

COMPENSATION

ON

*UPDATE VERSION

OFF *CAMERA TITLE

6) SPECIAL

MOTION DETECTION

PRICACY MASKING

IMAGE ADJUST

SETUP

LENS DC

EXPOSURE

WHITE BAL ATW1

BACKLIGHT OFF

DAY & NIGHT AUTO

SPECIAL

RESET

EXIT

SPECIAL

CAM TITLE ON

MOTION OFF

PRIVacY OFF

IMAGE ADJ.

DPC

LANGUAGE ENGLISH

VERSION 10 10 21

RETURN RET

*SPECIAL SUB MENU LIST

(

SPECIAL

CAM TITLE ON

MOTION ON

PRIVacY OFF

IMAGE ADJ.

DPC

LANGUAGE ENGLISH

VERSION 10 10 21

RETURN RET

SPECIAL

CAM TITLE ON

MOTION OFF

PRIVacY ON

IMAGE ADJ.

DPC

LANGUAGE ENGLISH

VERSION 10 10 21

RETURN RET

SPECIAL

CAM TITLE ON

MOTION ON

PRIVacY OFF

IMAGE ADJ.

DPC

LANGUAGE ENGLISH

VERSION 10 10 21

RETURN RET

013

108

OFF

011

167

255

AREA 4

AREA 8

ON 000 - 255

FONT 000 - 255

LCD

RETURN

ID&TITLE 000 - 255

USER

013

180

011

092

031

255

015

OFF

AREA SEL. AREA 1

AREA STATE ON

HEIGHT 000

WIDTH 000

LEFT/RIGHT 000

TOP/BOTTOM 000

DEGREE 000

VIEW ON

AREA SEL. AREA 1

AREA STATE ON

HEIGHT 000

WIDTH 000

LEFT/RIGHT 000

TOP/BOTTOM 000

COLOR 000

LENS SHAD. OFF

2DNR ON

MIRROR ON

FONT COLOR

CONTRAST 000

SHARPNESS 000

DISPLAY CRT

NEG. IMAGE ON

Attention When select ON,

AREA 1 always turns on

* LENS SHAD: LENS SHADING COMPENSATION

* 2 DNR: SIGNAL NOISE REDUCTION (2D)

* NEG IMAGE: NEGATIVE IMAGE

* GAMMA

* PED LEVEL

* COLOR GAIN

NVT INSTRUCTIONS

The cameras included in the QView™ series have the option of transmitting video signals to NVT receivers via unshielded twisted pair cable. You must purchase the receiver

separately. Instructions for connecting the receiver end of the unshielded twisted pair cable will be included with the NVT receiver. Following are instructions for connecting the

unshielded twisted pair cables to the RJ45 (Cat. 5) cable running outside your housing.

UNSHIELDED TWISTED PAIR VIDEO WIRING

1. Video for all four cameras is contained in the one RJ45 (Cat. 5) cable. An RJ45 female coupling is provided so that all connections can be made with an RJ45 connector. The

following is the wiring diagram for the four twisted pair wires that are included with the Cat. 5 cable.

2. Connect the other end of the unshielded twisted pair cable to the NVT receiver.

CAUTION: The unshielded twisted pair video signal is polarity dependent. The positive video wire for each camera MUST be connected to the positive terminal on the NVT receiver,

and negative MUST be connected to negative.

3. When using unshielded twisted pair cable you DO NOT need the BNC connector. All four BNC connectors are provided inside the housing for testing purposes. Be sure that there

is no video connection other than the unshielded twisted pair cable.

NOTE: The customer must purchase the Video Transceiver from

NVT. Part numbers are:

• NV-212A (500 ft.)

* NV-213A or NV-213A-M (1000 ft.)

• NV-652R, NV-862R, or NV-1662R (3000 ft.)

PIN WIRE COLOR CAMERA NUMBER

1 White/Green Camera 1 +

2 Green Camera 1 -

3 White/Orange Camera 2 +

6 Orange Camera 2 -

5 White/Blue Camera 3 +

4 Blue Camera 3 -

7 White/Brown Camera 4 +

8 Brown Camera 4 -

!

3

Wiring Notes

Wire — What to DO

1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or thicker, stranded

or solid, Category 2, 3, 4, or 5.

2. The video signal may co-exist in the same wire bundle as other video, telephone,

data, control signals, or low-voltage power. It is also OK to run NVT video signals in

or near electromagnetic fields (in accordance with National Electrical Code, local, or

other local safety requirements).

3. DO measure the wire distance. Use only transceivers that are designed for that

distance.

4. DO make sure the pair of wires carrying the video signal is sent as a twisted pair

(e.g. the blue-white/white-blue wires twisted together as a pair), not a “split-pair”

(e.g. blue-white conductor, part of one pair/orange-white conductor, part of another

pair).

Wire — What NOT to DO

1. DO NOT USE SHIELDED TWISTED PAIR WIRE. It will severely degrade the

distance performance. Short runs may be used with some signal degradation (for

example elevator traveler cables). Multi-pair wire with an overall shield is OK.

2. DO NOT USE UN-TWISTED WIRE. It will reduce the NVT product’s inherent

interference immunity.

3. DO NOT allow your installation to have “bridge-taps”, loading coils, talk-battery,

or MOV type protectors. Bridge-taps are where a twisted pair is connected to two

twisted pairs (such as an extension phone at home). Bridge-taps cause reflections

as the signal propagates, resulting in “ghosts” in the video image, and are to be

avoided.

4. If the phone company is providing the cable runs between buildings, make sure

it’s “dry copper” i.e. it should have none of the following: dial-tone, 48 volts, loading

coils, bridge-taps, switching, or long paths to the phone company’s central office and

back.

5. Due to near-end crosstalk, DO NOT send a transmit and a receive signal in the

same wire bundle. Exceptions: Less than 1,000 ft (300m), or Category 5 cable, up to

2,000 ft (600m) are OK.

6. DO NOT send “Up-the-Coax” Pan/Tilt/Zoom signals through active (amplified)

NVT transceivers.

Measure your wire distance

Note: All NVT quoted distance specifications include any coax in the run. It is

recommended that the wire distance be measured to ensure that the capability of the

NVT product is correct.

Wire resistance may be measured with an ohm-meter by shorting the two conductors

together at the far end, and measuring the loop-resistance out and back. Compare

your readings with the charts in the next column.

7. For safety, never put NVT signals in the same conduit as high-voltage

wiring.

8. WARNING — to reduce a risk of fire or electrical shock, do not expose

this product to rain or moisture.

28

27

26

25 24

23

22

21

20

19

18

17

33

31

32

30

29

16

15

7

13

12

11

10

9

8

7

6

5

4

3

2

17 1/4 x 20 FH SS Bolt 90-BTSR01 1

18 Housing Pendant Bracket 30-VL926 1

19 1/4 Split Lock Washer 92-WSSL01 1

20 1/4 Flat Washer 92-WSFL01 1

21 Housing Gasket 96-PSGK05 1

22 1/4 x 20 x 1/2" Set Screw 90-BTSS05 2

23 1/4 Flat Washer 92-WSFL01 4

24 1/4 Split Lock Washer 92-WSSL01 4

25 1/4 x 20 x .75" HH Bolts 90-BTHH27 4

26 1 1/2" Housing Coupling 30-VL917 1

27 Upper Housing Gasket 96-PSGK04 1

28 1/4 x 20 x .375" HH Bolts 90-BTHH39 2

n/s 1/4 Flat Washer 92-WSFL01 2

n/s 1/4 Split Lock Washer 92-WSSL01 2

Item No. Description Part No. Qty

2 FD8 Housing Top 30-VL1697 1

3 Dome Support Ring 30-VL1695 1

4 25W, 24Vac w/Leads 72-HT1752 1

5 FD8 Clear Dome 20-DCFD8 1

n/s FD8 Tinted Dome 20-DTFD8 1

n/s 9.25" O-ring 96-RSORG11 2

6 Plastic Ring Plugs 30-VL1696 6

7 FD8 PCB 76-FPD8PB 1

8 FD8 Upper Housing Bracket 30-VL1744 1

9 Housing Gasket 96-PSGK05 3

10 Housing Fan 71-VLBL03 1

11 Adapter Bracket (In Housing Packet) 40-PKFD8 1

12 1/4 x 20 x .75" HH Bolts 90-BTHH27 4

12 1/4 Split Lock Washer 92-WSSL01 4

12 1/4 Flat Washer 92-WSFL01 4

13 10 x 32 x .75 Phil PH SS 90-BTRP28 3

15 Captive Screw 30-VL1749 3

n/s Captive Screw Spring 92-SPR01 3

n/s Captive Screw Retainer 94-FSRT04 3

16 Main Housing Bracket 30-VL1742 1

n/s Housing Ring 1" Lanyard Spring 92-SPR02 1

n/s Lanyard Spring Screws 90-BTPEM01 2

n/s Packet Assembly 40-PKFD8 1

n/s Power/Control/Video Input Cable 40-CAFD802 1

n/s Product Instructions 81-IN5215 1

Pendant Assembly

EXPLODED VIEWS OF HOUSING

29 FD8 Upper Housing Bracket 30-VL1013 1

30 Indoor Housing Coupling 30-VL1744 1

31 1/4 Flat Washer 92-WSFL01 1

32 1/4 Split Lock Washer 92-WSSL01 4

33 1/4 x 20 x .75" HH Bolts 90-BTHH27 4

Indoor Pendant Assembly

34

36

37

35

38

34 PC Board and Input Cables Video/Power RPQF01

35 Multi Camera Metal Base Bracket RPQF02

36 Plastic Articulated Bracket RPQRH71000

37 Camera Bracket and Hardware RPQRH71010

38 Hi-Res Lens RPQF8ONA

Camera Arm Assembly

Use the formula below to select the correct power supply for cameras connected in parallel (positive to positive, negative to negative):

Total current for a 24 Vac system:

TOTAL CURRENT = (202mA x total number of cameras) Example: 202mA x 5 total cameras = 1010mA

Note: 202mA is camera plus power supply

CAMERAS VOLTAGE CURRENT POWER

1 24 Vac/Vdc 102mA 2.5W

2 24 Vac/Vdc 210mA 5W

3 24 Vac/Vdc 331mA 7.9W

4 24 Vac/Vdc 487mA 10.9W

CABLE AND POWER GUIDELINES

This chart shows the proper current needed for power supplies for QView Series cameras. Use Class 2 Power only. Input voltage must be 24 Vac/Vdc.

Power Supply Cable Maximum Length (feet/meters)

CAMERAS TOTAL LOAD POWER SUPPLY 24 AWG 22 AWG 18 AWG 16 AWG

1 2.5W 24 Vac/Vdc 1718/523 2733/833 6909/2106 10985/3348

2 5W 24 Vac/Vdc 834/254 1327/404 3356/1023 5335/1626

3 7.9W 24 Vac/Vdc 529/161 842/256 2129/649 3385/1032

4 10.9W 24 Vac/Vdc 359/109 572/174 1447/441 2300/701

NOTE: The above table is based on a "worst-case" power supply. Using a regulated or switching power supply can increase your cable distance. Moog recommends using our

PS24 power supply, or a CSA/UL listed Class 2 power supply.

Video Cable Maximum Length (feet/meters)

Cable Type RG-59 RG-6 RG-11

Wire Gauge 23 AWG* 18 AWG* 16 AWG*

Max. Length 750/229 1500/457 2000/610

* Copper clad steel core, 95% braided shield

AWG 250/76 500/152 1000/305 1500/457 2000/610 3000/914

18 3Ω 6Ω 13Ω 19Ω 26Ω 40Ω

20 5Ω 10Ω 20Ω 30Ω 40Ω 59Ω

22 8Ω 17Ω 33Ω 48Ω 66Ω 99Ω

24 13Ω 26Ω 52Ω 78Ω 108Ω 163Ω

Maximum Length (feet/meters)