Haier DW12-PFE8 series Istruzioni per l'uso

Index

EN

1

2

4

5

6

9

13

15

16

17

21

26

28

11

19

20

Safety information

Not suitable for the dishwasher

How to keep your dishwasher in shape

Installation

How to remove the top of your dishwasher

Getting to know your dishwasher

How to load the salt

How to load rinse aid

How to load the detergent dispenser

Arranging crockery, glasses, etc. in the dishwasher

Programme overview

Consumption

Washing dishes

Care and maintenance

Trouble Shooting

Technical data

Important information

32

33

EN

Safety information

At time of delivery

Check packaging and dishwasher immediately for signs of transport damage. If

the appliance is damaged, do not put it into use but contact your supplier or

customer service without delay.

Please dispose of packaging materials properly.

Ensure that the domestic wiring is properly earthed.

Site the dishwasher and connect it up in accordance with the installation instructions.

The dishwasher must not be connected to the electricity supply while installation

is being carried out.

The mains electricity supply must conform to the details shown on the dishwasher

nameplate.

Do not connect the dishwasher to the electricity supply via an extension cable.

After the appliance has been installed,the mains plug should still be easily

accessible.

During installation, the power supply cord must not be excessively or dangerously

bent or flattened.

This appliance cannot be installed outdoor, not even if the area in which it is

installed is covered by a roof; it is also very dangerous to leave it exposed to

the rain and elements.

During installation

During normal use

The dishwasher must only be used by adults for the washing of household dishes

and cooking utensils.

Do not place any heavy objects or stand on the door when it is open. The appliance

could tip forward.

The water inside the dishwasher is not suitable for drinking.

Do not use solvents of any kind inside your dishwasher. They could cause an

explosion danger.

Open the door very carefully if the dishwasher is operating. There is a risk of water

squirting out.

Do not touch the heating element during or after a wash cycle.

Fundamental rules to follow when using the appliance:

- Never touch the dishwasher when barefoot or with wet hands or feet;

- We discourage the use of extension cords and multiple sockets;

- If the appliance is not operating properly or maintenance must be performed,

disconnect the appliance from the power supply.

2

EN

If your family includes children

This appliance is not intended for use by persons (including children) with reduced

physical,sensory or mental capcabilities, or lack of experience and knowledge,unless

they have been given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure that they to not play with the appliance.

Keep detergents out of the reach of children, who must also be kept away from

the dishwasher when it is open.

If a fault occurs

If the appliance malfunctions, turn off water supply to the appliance and disconnect

the power supply turn off and the plug from the wall socket. Then, consult the

section entitled, "Fault finding" .If you cannot solve the problem, contact a service

center.

Only specialised personnel are authorised to make repairs.

If the supply cord is damaged, it must be replaced by the manufacture, its service

agent of similarly qualified persons in order to avoid a hazard.

To maintain the EFFICIENCY and SAFETY of this appliance,we recommend:

- call only the Service Centers authorized by the manufacturer, or the approved

Service agents.

- always use original Spare Parts.

When disposing of old appliances

Appliances which are no longer being used must be made inoperable by cutting

the power supply cord and removing the door lock.

Take the appliance to a designated waste disposal center.

Children could get locked in the appliance (risk of

suffocation) or get stuck in other positions. Therefore:

Remove the mains plug, cut the mains wire and set

aside. Damage the door lock so that the door can no

longer be closed.

Warning:

3

EN

Not suitable for the dishwasher

What you should not put into the dishwasher

Cutlery and tableware manufactured in whole or part from wood.They become faded

and unsightly in appearance.Furthermore,the adhesives that are used are not suitable

for the temperature that occur inside the dishwasher.Delicate decorative glassware

and vases,special antique or irreplaceable china. The decorative patterns on such

items will not be dishwasher-proof.

Plastic objects that are not resistant to hot water, copper and pewter utensils are

also not suitable. Decorative patterns printed or painted onto the surface of crockery,

glasses, etc.,aluminium and silver items tend to become discoloured or faded if

washed in the diswasher. Some types of glass can become opaque in appearance

after they have been washed many times in a dishwasher. Highly absorbent materials,

such as sponges and towels,should never be placed in the dishwasher.

Our recommendation

In future, only purchase table or kitchenware that has been confirmed as being

dishwasher-proof.

Dishes or cutlery that have been soiled by tobacco ash,

wax, Iubricating grease or paint, should not be put in the

dishwasher.

Important:

Damage to glassware and other dishes

Possible causes

Type of glass or manufacturing process

Chemical composition of detergent

Water temperature and duration of dishwasher programme.

Suggested remedy

Use glassware or porcelain dishes that have been marked ‘dishwasher-proof’ by

the manufacture.

Use a mild detergent that is described as ‘kind to dishes’. If necessary, seek further

information from detergent manufacturers.

Select a programme with a low temperature and a short duration as possible.

To prevent damage, take glass and cutlery out of the dishwasher as soon as

possible after the programme has ended.

4

EN

How to keep your dishwasher in shape

After every wash

Remove the plug

No solvents or abrasive cleaning products

After every wash, turn off the water supply of the appliance and leave the door

slightly ajar so that moisture and odors are not trapped inside.

Before cleaning or performing maintenance, always switch off the appliance, and

remove the plug from the socket. Do not run risks.

To clean the exterior and rubber parts of the dishwasher, do not use solvents or

abrasive cleaning products. Rather, It is recommended that you use only a cloth

and warm soapy water.

To remove spots or stains from the surface of the interior, use a cloth dampened

with water and a little white vinegar, or cleaning product made specifically for

dishwashers.

Moving the appliance

Seals

When you go on holiday

If the appliance must be moved, try to keep it in a vertical position. If absolutely

necessary, it can be positioned on its back.

One of the factors that cause odors to form in the dishwasher is food that remains

trapped in the seals. Periodic cleaning with a damp sponge will prevent this from

occurring.

The door should not be left in the open position since this could present a tripping

hazard.

When you go on holiday, it is recommended that you run a wash cycle with the

dishwasher empty and then remove the plug from the socket, turn off the water

supply and leave the door of the appliance slightly ajar. This will help the seals last

longer and prevent odors from forming within the appliance.

5

EN

Installation

Positioning the appliance

Positioning the appliance in the desired location. The back of the appliance should

rest against the wall, and the sides, along the adjacent cabinets or wall. The

dishwasher is equipped with water supply and drain hoses that can be positioned

to the right or the left to facilitate proper installation.

Levelling the appliance

Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust

the dishwasher, making it level. The appliance should not be inclined more than

2˚. If the appliance is level, it will help ensure proper performance.

Cold water connection

Connect the water supply hose to a

threaded 3/4 (gas) connector, making sure

that it is fastened tightly in place (see fig.A).

If the water pipes are new or have not

been used for an extended period of time,

let the water run to make sure that the

water is clear and free of impurities. If this

precaution is not taken, there is a risk that

the water inlet can get blocked and damage

the appliance.

The appliance is to be connected to the water mains

using new hose-sets and that old hose-sets should not

be reused.

Warning:

6

fig.A

EN

7

fig.B

Some models are fitted with an "Aquastop"

water supply hose (see fig.B) in which the

small filter is already housed in the

threaded end.

Anti-Flooding protection

The dishwasher is equipped with a system that stops the supply of water in the

event of a problem with the water supply hose, or leaks within the unit, in order to

prevent damage to your home. If for any reason the box containing the electrical

components happens to get damaged, turn off the power supply and remove the

plug for the appliance from the socket immediately. In order to guarantee that the

anti-flooding feature operates properly, the "A" box with water supply hose must

be attached to the water supply tap as shown in fig.B. No other type of connection

is acceptable.The water supply hose must not, under any circumstances, be cut,

as it contains electrical parts which are live. If the length of the hose is not adequate

to make a proper connection, the hose must be replaced with one which is long

enough. This hose is available upon request from specialised retailers and approved

service center.

Anti-Flooding protection

Under no circumstance should the water inlet hose be cut as it

contains live electrical parts.

WARNING:HAZARDOUS VOLTAGE!

EN

Drain hose connection

Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run

into the sink, making sure to avoid bending or crimping it. If necessary, fit a syphon

trap (U-bend) with a connecting piece for the electrical drain hose (fig.C). The free

end of the hose must be at a height between 40 and 100 cm and must not be

immersed in water.

fig.C

Attention:

The connecting piece for syphon trap (U-bend) must be

securely fastened to the wall to prevent the drain hose

from moving and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values for the current in the home

correspond to those on the rating plate (located on the stainless steel inner door

of the appliance) and that the electrical system is correct for the maximum voltage

on the rating plate, insert the plug into an electrical socket which is earthed properly

(the earthing of the appliance is a safety requirement mandated by law).

Caution:

The dishwasher plug must be accessible even when the

appliance is installed as a built-in unit so that maintenance

can be done safely.

min 40 cm

max 100 cm

2m max

8

EN

How to remove the top of your dishwasher

Freestanding dishwasher can also be used as built-in,

according to following processes:

9

EN

10

0120200050

Built In Dishwasher: fixing on top

Built In Dishwasher: fixing on side

EN

Getting to know your dishwasher

Function overview

G

H

I

J

K

L

ON-OFF Indicator

ON-OFF Button

Delay Start Button

Additional option Button

Programme symbols

A

B

C

D

E

F

Time-remaining Indicator

Additional option symbols

Inlet Fault Indicator

Low Rinse Aid Indicator

Low Salt Indicator

Programme Button

Start/Pause Button

55

o

/65

o

70

o

55

o

50

o

45

o

40

o

cold

A C E K

B D F G H I J L

11

Press this two buttons for 3 seconds to concel the programme.

Press this button to delay the start of programme.

Press this button to select the Additional option function.

Upper Rack Wash function

Lower Rack Wash function

Combi-detergent tablets option

Press this button to select the programme.

Press this button to start or pause the programme.

EN

a

c

e

k

b

d

f

g

h

i

j

g

h

i

j

k

Upper Rack

Top Spray Arm

Lower Rack

Silverware Basket

Bottom Spray Arm

a

b

c

d

e

f

Salt Container Cap

Water Inlet Hose

Drain Hose

Power Supply Cord

Washing Filter

Detergent and Rinse Aid Dispenser

Dishwasher interior

12

EN

How to load the salt

Salt

The hardness of the water varies from place to

place. If hard water is used in the dishwasher,

deposits will form on the dishes and utensils.

The appliance is equipped with a special softener

that uses a salt specifically designed to eliminate

lime and minerals from the water.

Loading the salt into the container

J

When the low salt indicator “J” lights, you must

fill the salt.

Remove the lower rack and then unscrew and

remove the cap from the salt container;

If you are filling the container for the first time,

fill it with water;

Place the end of the funnel (supplied) into the

hole and introduce about 2 kg of salt. It is normal

for a small amount of water to come out of the

salt container.

Carefully screw the cap back on.

Important:

To prevent the formation of rust, load the salt just before

beginning a wash cycle.

Always use salt intended for use with dishwashers.

The salt container is located beneath the lower rack and should be filled as follows:

13

EN

Adjusting salt consumption

The dishwasher is designed to allow for adjusting the amount of salt consumed

based on the hardness of the water used. This is intended to optimize and customize

the level of salt consumption so that it remains at a minimum.

To adjust salt consumption, proceed as follows:

Unscrew the cap from the salt container;

There is a ring on the container with an arrow on

it (see figure to the side).

If necessary, rotate the ring in an anticlockwise

direction from the "-" setting towards the "+"

sign, based on the hardness of the water being

used.

It is recommended that adjustments be made in accordance with the following

table:

14

The default setting of the water softening system is -.

- If using multi-functional tablets fill the salt dispenser and set the adjuster to -; if

the hardness of the water is greater than 60ºfH, set it to +.

Hardness of the water

ºdH ºfH °mmol/l

0 -10

/ 0 /

- 20 60

40 40

>89

+ 60 25

Selector

knob

position

Salt

consumption

(grams/cycle)

Autonomy

(cycles/2 kg)

0-17

10-25

25-50

>50

18-44

45-89

0-1,7

1,8-4,4

4,5-8,9

>8,9

MED

EN

How to load rinse ald

Rinse aid

I

This product makes dishes sparkle and helps them

to dry without spotting. The dispenser is located

on the inside panel of the door .When the low rinse

aid indicator " I "on the control panel and the

mechanical indicator " 1 " on the dispenser light,

you must load rinse aid.

Loading the rinse aid

Regardless of the type of detergent dispenser

installed on your appliance, you must proceed as

indicated below when loading the rinse aid.

To open the dispenser, turn the "2" cap in an anti-

clockwise direction and then pour in the rinse aid,

making sure not to overfill. The amount of rinse

aid used for each cycle can be regulated by turning

the " 3" dose adjustor, located beneath the "2"

cap, with a screwdriver. There are 6 different

settings; the normal dosage setting is 3.

2

3

1

Notice:

When using combi-detergent tablets,like "3 in 1", "4 in 1",

"5 in 1"... the rinse-aid is no longer useful.

Important:

Proper dosage of the rinse aid improves drying. If drops

of water remain on the dishes or spotting occurs, the

dosage adjustor should be turned to a higher setting. If

the dishes have white streaks, turn the dosage adjustor

to a lower setting.

15

EN

Loading the detergent

Notice:

How to load the detergent

4

5

6

7

Detergent

Detergent specifically intended for use with

dishwashers must be used. The dispenser must

be refilled before the start of each wash cycle

following the instructions provided in the

"Programme overview". The detergent dispenser

is located on the inside panel of the door.

If you use normal detergent ...

To open the " 4 " cover on the dispenser, press

the "5" button.

The detergent for the wash cycle should be

poured into the " 6 " compartment.

The detergent for the pre-wash cycle should be

poured into the “ 7 ” compartment.

After the detergent has been placed in the

dispenser, close the cover and press down until

it clicks in place.

If you use "combi-detergent tablets" , like "3 in 1", "4 in 1", "5 in 1"...

Notice:

To facilitate closing the cover, remove any excess

detergent on the edges of the dispenser.

If you use "combi detergent tablets" , you have to select

combi-detergent tablets option function.

To open the " 4 " cover on the dispenser, press the "5" button.

The "tablets" should be poured into the " 6 " compartment.

After the detergent has been placed in the dispenser, close the cover and press

down until it clicks in place.

16

EN

Arranging crockery, glasses, etc. in the dishwasher

Before placing the dishes in the dishwasher, remove larger food particles to prevent

the filter from becoming clogged, which results in reduced performance.

If the pots and pans have baked-on food that is extremely hard to remove, we

recommend that they are soaked before washed. This will eliminate the need for

extra wash cycles.

Pull out the rack to load the dishwasher.

How to use the lower rack

We recommend that you place the most difficult to

clean items on the bottom rack: pots, pans, lids,

serving dishes and bowls, as shown in the figure

to the right.

It is preferable to place serving dishes and lids on

the sides of the racks in order to avoid blocking the

rotation of the top spray arm.

fig.D

Pots, serving bowls, etc. must always be placed

face down(see fig.D).

Deep pots should be slanted to allow the water

to flow out.

Some models: the lower rack features fold down

tine rows (see fig.E) so that larger or more pots

and pans can be loaded.

The silverware basket can be doubled (see fig.F)

so that only one section may be used when the

silverware load is light. This also makes space

for additional pots and pans and it can also be

placed in the upper rack.

Silverware should be placed in the silverware

basket with the handles at the bottom; if the rack

has side baskets, the spoons should be located

individually into the appropriate slots. Especially

long utensils should be placed in the horizontal

position at the front of the upper rack.

17

fig.F

E1 E2 E3

fig.E

EN

fig.I

How to use the upper rack

The upper rack is designed to hold more delicate

and lighter dishware, such as glasses, cups and

saucers, plates, small bowls and shallow pans (as

long as they are not too dirty).

The dishes and cookware shall be arranged, so

that they do not get moved by the spray of water.

The upper rack can be adjusted for height by

using the knobs located on both sides of the rack

itself (see fig.G).

Adjust the upper basket to the higher level and you

have more space to accommodate those taller pans

and trays in the bottom basket.

Shelf

Lean tall glasses and those with long stems against

the shelf-not against other items to be washed.

Place glasses, cups and small bowls on the

additional cup rack. The additional cup rack can be

swivelled in or out as required(see fig.H).

fig.G

fig.H

18

Warning:

knives and other utensils with

sharp points must be loaded in

the basket with their points

down or placed in a horizontal

position.

Knife rack

The knife rack clips onto the side of the top basket,

giving you the freedom to wash your large sharp

knives separately and out of harm’s way (see fig.I).

(Some models)

EN

Programme overview

19

Automatic

Prewash with cold water.

Main wash at 55°C or 65°C.

1 or 2 rinses with cold water.

Rinse with hot water.

Drying.

Pre-wash with warm water.

Extended wash at 70°C.

Rinses with cold water.

Rinse with hot water.

Drying.

55

o

/65

o

70

o

55

o

50

o

45

o

40

o

cold

Wash

programme

Type of

crokery

Nondelicate

( e.g.china,

pots/pans,

cutlery, etc)

Mixed

( e.g.china,

pots/pans,

cutlery,

glasses,

etc)

Amount

of food

remains

Condition

of food

remains

a lot

a little

Very

little

Description of cycle

Pre-wash use cold water.

Extended wash at 55°C.

Rinse with cold water.

Rinse with hot water.

Drying.

Pre-wash use cold water.

Extended wash at 50°C.

Rinse with cold water.

Rinse with hot water.

Drying.

Wash at 45°C.

Rinse with warm water.

Hot rinse.

Drying.

Short wash at 40°C.

Hot rinse.

Short cold wash to prevent

food residue from drying

on the dishes .

stuck

on hard

loosely

attached

loosely

attached

Type of

food

remains

Soups,

casseroles,

sauces,

potatoes,

pasts, rice,

eggs,

roastor

fried food.

Soups,

potatoes,

pasta, rice,

eggs, roastor

fried food.

Coffee,

cakes,

milk,

sausage,

cold drinks,

salads

Rinse off if the dishes have

been stacked for several

days in the dishwasher prior

to washing.

Intensive

Normal

Light

Glass

Rapid

Green

Soak

Extended wash at 48°C.

Rinse with cold water.

Rinse with hot water.

Drying.

Soups,

potatoes,

pasta, rice,

eggs, roastor

fried food.

La pagina si sta caricando...

Haier DW12-PFE8 series Istruzioni per l'uso

Haier DW12-PFE8 series Istruzioni per l'uso

in altre lingue

Documenti correlati

Altri documenti