Ariston AS 60 V Manuale del proprietario

Categoria
Asciugatrici elettriche
Tipo
Manuale del proprietario

Questo manuale è adatto anche per

Contents
TUMBLE DRYER
AS60V
Instruction booklet
Installation, 2-3
Where to put your dryer
Ventilation
Electrical connection
Before you start using your dryer
Dryer description, 4
The front
The back
Control panel
Start and programmes, 5-6
Choosing a programme
Table of programmes
Laundry, 7-8
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 9
General safety
Disposal
Saving energy and respecting the environment
Maintenance and Care, 10
Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Cleaning the dryer
Troubleshooting, 11
Service, 12
Spare parts
GB
English, 1
I
Italiano, 13
F
Français, 25
D
Deutsch, 37
E
Español, 49
NL
Nederlands, 73
A
Arabic, 96
P
Português, 61
GB
1
! Ensure that the end of the tube is not directed toward
the air intake vent at the rear of the dryer.
! The vent tube should not exceed 2.4 metres in length
and should be kept free of any possible
accumulation of fluff, lint and water by shaking it out
frequently. Always ensure that the tube is not
squashed.
Permanent venting
In conjunction with the vent tube we recommend using
a Wall/Window Vent Kit, available at a retail location or
the nearest Spare Parts Dealer.
Wall mounting
1. Leave an opening in
the wall to the left of the
dryers proposed position.
2. Keep the tube as short
and straight as possible to
prevent condensed
moisture from backing up
into the dryer.
3. Similarly, the duct in the
wall should slope
downwards towards the
outside.
Window mounting
1. With a stacked dryer
the hole in the window
should ideally be made
below the vent.
2. The tube should be
kept as short as possible.
Depending on how often you use your dryer, it is
essential that areas A and B are checked periodically
to remove lint or debris.
The vent tube adaptor must be fitted securely thus
preventing any humid air from being emitted back into
the room.
! The Dryer should not be pushed so far back that the
tube adaptor is pulled out of position or the tube is
squashed or bent.
! The tube should be kept clear of the air intake vent
and kinks or ‘U’ bends must be avoided as these will
obstruct the tube or trap condensation.
Installation
2
GB
! Keep this instruction booklet on hand in order to
refer to it when necessary. Take it with you when you
move, and, should you sell this appliance or pass it
on to another party, make sure that this booklet is
supplied along with the dryer so that the new owner
may be informed about warnings and suggestions on
how the dryer works.
! Read these instructions carefully; the following
pages contain important information on installation
and suggestions on how the appliance works.
Where to put your dryer
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
If you are going to install the appliance under a
work counter, be sure to leave a 10mm space
between the top and any other objects on or
above the machine and a 15mm space between
the sides and lateral furnishings or walls. This is
to ensure proper air circulation. Make sure that
the back vents are not obstructed.
Make sure you put your dryer in an environment
that is not damp and has proper air circulation
throughout.
Ventilation
The Dryer dries your laundry by drawing in cool, clean
and relatively dry air, heating it, and then
distributing it through the clothes as they are gently
tumbled. For optimum performance, the moist air is
then blown out through a vent tube at the back of the
dryer.
When the dryer is in use, there has to be adequate
ventilation to avoid the back flow of gases into the
room from appliances burning other fuels, including
open fires.
Mobile venting
A vent tube must always be fitted when the dryer is
used in conjunction with Mobile Venting.
The tube must be fitted securely into the back of the
dryer (see Dryer Description). If possible, it is always
best to connect the tube to a permanent
outlet close to the dryer. If permanent installation is
not possible, the dryer will work just as well with the
tube passing through a partly-opened window.
Installation
Description
Start and
Programmes Laundry
Warnings and
Suggestions
Maintenance and
Care Troubleshooting Service
GB
3
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this dryer
and fitted only by authorised technicians (see
Service). New or longer power cords are supplied at
an extra charge by authorised dealers..
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.
Levelling your dryer
The dryer must be installed level for correct operation.
When you have installed
your dryer in its final
location check that it is
level first side to side,
then front to back.
If the dryer is not level,
use a wooden block to
support it while adjusting
the two front legs up or
down, until your dryer is
level.
Before you start using your dryer
Once you have installed your dryer and before you
use it, clean the inside of the drum to remove any
dust that could have accumulated during transport.
Open window venting
The end of the tube
should be directed
downwards, to prevent
warm moist air from
condensing in the room
or in the dryer.
! Ensure that the dryer is adequately ventilated and
that the end of the vent tube is not directed towards
the air intake duct.
! The vent tube must always be fitted for optimum
performance.
! Make sure that the vent tube and air intake vents
are not obstructed or blocked.
! The dryer must not recycle exhaust air.
! Misusing a tumble dryer may create a fire hazard.
! Do not discharge exhaust air into a flue which is
used for exhaust fumes from other appliances that
burn gas or other fuels.
Electrical connections
Make sure of the following before you insert the plug
into the the electrical socket:
The socket must be grounded.
The socket must be able to sustain the machines
maximum power, which is indicated on the rating
label (see Dryer Description).
Power voltage must be within the values indicated
on the rating label (see Dryer Description).
The socket must be compatible with the dryers
plug. Should this not be the case, replace the
plug or the socket.
! The dryer must not be installed outdoors, even if
the space is sheltered. It can be very dangerous if it
is exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
Control panel
The front The back
Drying Guide
PROGRAMMES
Knob
TIMER
Knob
START
Button
Indicator
ACTIVE
Light
Control Panel
Drum
Model & Serial
numbers
Filter
The Drying Guide allows you to consult a user
friendly table of fabric types and load capacities.
The TIMER knob sets a delay on the dryer’s start time.
Rotate it clockwise until you reach the number of
hours you want to delay the start time: If you have
gone too far, turn the knob counter-clockwise (see
Start and Programmes).
The PROGRAMMES knob sets the programme: rotate
it clockwise, never counter-clockwise, until the
indicator is pointing to the programme you want to
select (see Start and Programmes).
Dryer Description
4
GB
The START button begins drying a selected
programme (see Start and Programmes).
The HEAT button selects drying temperature (see
Start and Programmes).
OUT: HIGH heat. IN: LOW heat.
The ALARM buzzer signals the end of a drying cycle.
OUT: Buzzer ON. IN: Buzzer OFF.
The ACTIVE indicator light signals that your dryer is in
use. This light will glow when the START button is
pressed. It will remain on until the door is opened or
the power is turned off. This light will be on during a
delayed start programme.
HEAT
Button
ALARM
Button
Air Intake Vent
Vent Tube fitted here
Caution: Hot!
Rating plate
Choosing a programme
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
3. Open the door and make sure the filter is clean
and in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. Choose the drying programme by checking the
Programmes table (see Programmes) as well as
the indications for each type of fabric (see
Laundry).
- Set the temperature with the HEAT button.
- Select a programme or drying time by rotating
the PROGRAMMES knob clockwise.
6. Set a delay time by using the TIMER knob if
necessary.
Installation
Description
Start and
Programmes Laundry
Warnings and
Suggestions
Maintenance and
Care Troubleshooting Service
GB
5
7. If you wish to eliminate the buzzer sound, press
the ALARM button.
8. Press the START button to begin. The DRYING
indicator light will turn on and will stay on, even
during the delay. The indicator light will remain
on until you open the dryer door.
During the drying programme, you can check on
your laundry and take out items that are dry
while others continue drying. When you close
the door again, press the START button in order
to resume drying.
9. About 10 minutes before the programme is
completed, it enters the final COOL TUMBLE
phase (fabrics are cooled), which should always
be allowed to complete.
10. The buzzer will warn you when drying is
complete. Open the door, take the laundry out,
clean the filter and replace it (see Maintenance).
11. Unplug the dryer.
Start and Programmes
1. Select HIGH HEAT by pressing
the HEAT button.
2. Position the PROGRAMMES knob
on .
3. Press the START button , the
ACTIVE light will turn on.
1. Select HIGH HEAT by pressing
the HEAT button.
2. Position the PROGRAMMES knob
on .
3. Press the START button , the
ACTIVE light will turn on.
Programmes
Programme
What it does... How to set it...
Note:
Automatic
Drying
(average loads)
Dries completely:
your clothes are ready to be
worn. For average loads (from 1
to 3kg) of Cotton ,
polycotton or synthetics .
! If you select LOW HEAT,
this programme will not dry
your clothes. For Acrylic
fibres or small loads select
Timed Drying.
This programme can also be
used for large loads if you
require a slightly drier result.
1. Select HIGH HEAT by pressing
the HEAT button.
2. Position the PROGRAMMES knob
on .
3. Press the START button , the
ACTIVE light will turn on.
Automatic
Drying
(large loads)
Dries completely:
your clothes are ready to be
worn. For large loads (from 3 to
6kg) of Cotton .
! If you select LOW HEAT,
this programme will not dry
your clothes. For Acrylic
fibres or small loads select
Timed Drying.
This programme can also be
used for average loads if you
prefer a damper result.
Timed Drying
up to 120 minutes
Dries wet clothes that will be
ironed, Acrylic fibres , or
small loads (less than 1kg).
Consult suggested drying
times (see Laundry).
Always allow the dryer to
complete this phase.
This is the programmes final phase.
Approximately 10 minutes before the
finish, the knob advances
automatically to the Cool Tumble
Phase. After the Buzzer will sound (if
selected) and the clothing is ready
to be taken out.
Heating elements turn
themselves off and clothing is
cooled down.
1. Select required heat setting HIGH
HEAT or LOW HEAT by
pressing the HEAT button.
2. Position the PROGRAMMES knob
on the desired time.
3. Press the START button , the
ACTIVE light will turn on.
Easy Iron
Cool Tumble
Phase
Brief programme (approximately
10 minutes) that softens fibres of
clothing that is ready for ironing.
! This is not a drying
programme (see below).
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time. The cycle
relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric Maximum load
Cotton and Cotton mixtures 2.5kg
Synthetics 2kg
Denim 2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put
them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or Cotton mix,
and less well on acrylic fibres and on materials such as Tencel®.
6
GB
Start and Programmes
Sorting your laundry
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Empty pockets and check buttons.
Close zippers and hooks and tie loose belts and
strings.
Wring out each item in order to eliminate as much
excess water as possible.
! Do not load dripping wet clothes into the dryer.
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres: 6kg max (13lb)
Synthetic fibres: 3kg max (6.6lb)
! DO NOT overload the dryer as this could result in
reduced drying performance.
Typical load
Clothes
Blouse Cotton 150g 5oz
Other 100g 3oz
Dress Cotton 500g 1lb 2oz
Other 350g 12oz
Jeans 700g 1lb 6oz
10 nappies 1000g 2lb 3oz
Shirt Cotton 300g 10oz
Other 200g 7oz
T-Shirt 125g 4oz
Household Items
Duvet cover Cotton 1500g 3lb 5oz
(Double) Other 1000g 2lb3oz
Large Tablecloth 700g 1lb 6oz
Small Tablecloth 250g 9oz
Tea Towel 100g 3oz
Bath Towel 700g 1lb 6oz
Hand Towel 350g 12oz
Double Sheet 500g 1lb 2oz
Single Sheet 350g 12oz
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
Wash Care Labels
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
May be tumble dried
Do not tumble dry
Tumble dry at high heat setting
Tumble dry at low heat setting
Items not suitable for tumble drying
Articles that containing rubber or rubber-like
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Glass fibres (certain types of draperies)
Items which have been dry cleaned
Items with the ITCL Code (see Special
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Laundry
Installation
Description
Start and
Programmes Laundry
Warnings and
Suggestions
Maintenance and
Care Troubleshooting Service
GB
7
Special clothing items
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
Starched articles: do not dry these with non-starched
items. Make sure that as much of the starch solution is
removed from the load as possible before placing it in
the dryer. Do not over-dry: the starch will become
powdery and leave your clothing limp, which defeats
the purpose of starch.
Drying times
The table below presents APPROXIMATE drying times
in minutes. Weights refer to dry garments:
Cottons
High (full) Heat
Drying times 800-1000rpm in washing machine
Half Load Full Load
1kg 2kg 3kg 4kg 5kg 6kg
20-30 35-45 45-60 60-70 70-80 80-100
Synthetics
High (full) Heat
Drying times on reduced spin in washing machine
Half Load Full Load
1kg 2kg 3kg
20-30 35-45 45-60
Acrylics /
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load Full Load
1kg 2kg
25-40 40-60
Times are approximate and can vary depending
upon:
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
Fabrics: items that are the same type of fabric but
different textures and thicknesses may not have
the same drying time.
Quantity of laundry: single items or small loads
may take longer to dry.
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
Heat setting.
Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to
dry your clothes.
Bulk: some bulky items can be tumble dried with
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
! Do not over-dry your clothes.
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
8
GB
Laundry
! The appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons and
must be read carefully.
This appliance conforms to the following
EEC Directives:
- 72/23/EEC and 93/68/EEC (Low Voltage Equipment)
- 89/336/EEC, 92/31/EEC and 93/68/EEC
(Electromagnetic Compatibility)
General safety
This tumble dryer has been designed for home,
and not professional use.
This dryer must be used by adults, and the
instructions in this booklet should be followed carefully.
Do not touch the appliance while barefoot or with
wet hands or feet.
Unplug the machine by pulling on the plug, not
the cord.
Children must not be in proximity of the dryer
when in use. After using the dryer, turn it off and
unplug it. Keep the door closed to make sure that
children do not use it as a toy.
The appliance must be installed correctly and
have proper ventilation. The air intake vents
behind the machine, the outlet vents and the vent
tube should never be obstructed (see Installation).
Never direct the vent tube outlet towards the air
intake at the back of the machine.
Never allow the tumble dryer to recycle exhaust air.
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
Check to see if the dryer is empty before loading it.
The back of the dryer could become very
hot. Never touch it while in use.
Do not use the dryer unless the filter is securely
in place (see Maintenance).
Do not use liquid fabric softeners in the dryer, add
it to the final rinse of your wash.
Do not overload the dryer (see Laundry) for
maximum loads.
Do not load items that are dripping wet.
Tumble dry items only if they have been washed
with detergent and water, rinsed and been through
the spin cycle. It is a fire hazard to dry items that
HAVE NOT been washed with water.
Carefully check all instructions on clothing labels
(see Laundry).
Do not dry garments that have been treated with
chemical products.
Never dry articles that are contaminated with
flammable substances (petrol, oil, paint, hair
spray, creams, cooking fat or oils).
Do not tumble dry rubber, foam rubber, plastic, plastic
foam, nappy pants or liners, polythene or paper.
Installation
Description
Start and
Programmes
Laundry
Warnings and
Suggestions
Maintenance and
Care Troubleshooting Service
GB
9
Do not tumble dry large, very bulky items.
Do not tumble dry acrylic fibres at high temperatures.
Complete each programme with its Cool Tumble Phase.
Do not turn off the dryer when there are still warm
items inside.
Clean the filter after each use (see Maintenance).
Do not allow lint to collect around the dryer.
Never climb on top of the dryer. It could result in
damage.
Always follow electrical standards and requirements
(see Installation).
Always buy original spare parts and accessories
(see Service).
Recycling and disposal information
As part of our continued commitment to helping the
environment, we reserve the right to use quality recycled
components to keep down customer costs and minimise
material wastage.
Disposing of the packaging material: follow local
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream.
Old appliances must be collected separately in order
to optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
The crossed out “wheeled bin” symbol on
the product reminds you of your obligation,
that when you dispose of the appliance it
must be separately collected.
Consumers should contact their local authority or
retailer for information concerning the correct disposal
of their old appliance.
Saving energy and respecting the
environment
Wring out items to eliminate excess water before
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
Always dry full loads - you save energy: single
items or small loads take longer to dry.
Clean the filter after each use to contain energy
consumption costs (see Maintenance).
Warnings and Suggestions
Check the drum after each cycle
Turn the drum manually in order to remove small items
(handkerchiefs) that could have been left behind.
Cleaning the drum
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
Cleaning
External parts in metal or plastic and rubber parts
can be cleaned with a damp cloth.
Periodically check the vent tube and any
permanent venting fixture to make sure that there
has been no accumulation of fluff or lint, and
remove it.
Remove lint that collects around the filter and the
outlet vents.
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
Maintenance and Care
10
GB
Switching off the electricity
Unplug your dryer when not using it, when cleaning it
and during all maintenance operations.
Clean the filter after each cycle
The filter is an important part of your dryer:
it accumulates lint and fluff that is formed while drying.
Small items could also become trapped in the filter.
When finished drying, therefore, clean the filter by
rinsing it under running water or with your vacuum
cleaner. Should the filter become clogged up, the airflow
inside the dryer will be seriously compromised: drying
times lengthen and you will consume more energy. It
may also damage your dryer.
The filter is found in front
of the dryer trim
(see diagram).
Removing the filter:
1. Pull the plastic grip of
the filter upwards (see
diagram).
2. Clean the filter and
replace it correctly.
Ensure the filter is fully
located flush into the
tumble dryer trim.
! Do not use the dryer without replacing the filter.
Troubleshooting
Problem:
The tumble dryer won’t start.
Drying cycle will not begin.
Its taking a long time to dry.
Possible causes / Solution:
The plug is not plugged into the socket, or not making contact.
There has been a power failure.
The fuse has blown. Try to plug another appliance into the socket.
You are using an extension cord? Try to plug the dryer’s power cord
directly into the socket.
The door is not closed securely?
The PROGRAMMES knob has not been set properly (see Start and
Programmes).
The START button has not been pressed (see Start and Programmes).
You have set a delayed time (see Start and Programmes).
The filter has not been cleaned (see Maintenance).
The temperature setting is not ideal for the type of fabric you are drying
(see Start and Programmes).
Auto Programmes require a HIGH temperature setting (see Start and
Programmes).
The correct programme has not been selected for the load (see Start
and Programmes).
The flexible vent tube is obstructed (see Installation).
The air intake vent is obstructed (see Installation).
The permanent ventilation flap on the storm cover is obstructed (see
Installation).
The items were too wet (see Laundry).
The dryer was overloaded (see Laundry).
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
Installation Description
Start and
Programmes Laundry
Warnings and
Suggestions
Maintenance and
Care Troubleshooting Service
GB
11
Service
Spare Parts
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
Call an authorised technician if you experience problems
while using the machine.
The spare parts have been designed exclusively for
this appliance and not for other uses.
Service
12
GB
Before calling the Service Centre:
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service Centre
closest to you.
What to tell the Service Centre:
name, address and post code.
telephone number.
the type of problem.
the date of purchase.
the appliance model (Mod.).
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
Indice
ASCIUGATRICE
AS60V
Libretto di istruzioni
Installazione, 14-15
Dove installare l’asciugatrice
Aerazione
Collegamento elettrico
Informazioni preliminari
Descrizione del prodotto, 16
Lato anteriore
Lato posteriore
Pannello di controllo
Avvio e programmi, 17-18
Scelta del programma
Tabella dei programmi
Bucato, 19-20
Controllo del bucato
Etichette con le istruzioni per il lavaggio
Tessuti particolari
Tempi di asciugatura
Avvertenze e suggerimenti, 21
Sicurezza
Smaltimento
Risparmio energetico e rispetto dell’ambiente
Cura e manutenzione, 22
Scollegamento dell’apparecchio dalla rete elettrica
Pulizia del filtro al termine di ogni ciclo
Controllo del cestello al termine di ogni ciclo
Pulizia dell’asciugatrice
Ricerca guasti, 23
Assistenza, 24
Ricambi
GB
English, 1
I
Italiano, 13
F
Français, 25
D
Deutsch, 37
E
Español, 49
NL
Nederlands, 73
A
Arabic, 96
P
Português, 61
I
13
! Fare attenzione a non rivolgere il tubo di aerazione
verso la presa d’aria, che si trova nel lato posteriore
dell’asciugatrice.
! Il tubo di aerazione non deve superare la lunghezza
massima di 2,4 metri; deve inoltre essere scosso con
frequenza per rimuovere eventuali depositi di laniccio,
polvere o acqua. Fare attenzione a non calpestare il tubo.
Sistema di aerazione fisso
Si consiglia di collegare il tubo di aerazione ad uno
dei sistemi di aerazione per finestra o porta, disponibili
presso il rivenditore da cui è stata acquistata
l’asciugatrice o presso il più vicino rivenditore di parti
di ricambio.
Foro di aerazione su parete
1. Lasciare un’apertura
nella parete alla sinistra
del punto in cui verrà
installata l’asciugatrice.
2. Fare in modo che il
tubo sia quanto più
corto e dritto possibile,
così da evitare che
l’umidità, condensandosi,
possa rifluire
nell’asciugatrice.
3. Allo stesso modo, anche il foro nella parete deve essere
dritto e in discesa, così do non ostacolare il deflusso dell’aria
verso l’esterno.
Foro di aerazione su finestra
1. In linea teorica, quando
l’asciugatrice è a pieno
carico, il foro di
aerazione dovrebbe
trovarsi direttamente
dietro la ventola.
2. È importante quindi
che il tubo sia il più
corto possibile.
Le aree A e B devono essere controllate frequentemente,
per prevenire il formarsi di laniccio o detriti, specialmente
nei casi di uso frequente dell’asciugatrice. L’adattatore
per il tubo di aerazione deve essere montato
correttamente, così da evitare che l’aria umida possa
rientrare nella stanza.
! Fare attenzione a non spingere troppo indietro l’asciugatrice,
perché in questo modo si rischia di schiacciare, piegare
o addirittura scollegare il tubo di aerazione.
! Il tubo non deve presentare tagli, strozzature o curve
a “U” che potrebbero ostruire la ventilazione o intrappolare
la condensa.
Installazione
14
I
! Tenere a portata di mano il presente libretto, così da
poterlo consultare facilmente ad ogni evenienza.
Tenere il libretto sempre vicino all’asciugatrice; nel
caso in cui l’apparecchio venga venduto o ceduto ad
altre persone, ricordarsi di consegnare loro questo
libretto, così da permettere anche ai nuovi possessori
di conoscere le avvertenze e i suggerimenti sull’utilizzo
dell’asciugatrice.
! Leggere attentamente queste istruzioni: le pagine
che seguono contengono importanti informazioni
sull’installazione e utili suggerimenti sul funzionamento
dell’elettrodomestico.
Dove installare l’asciugatrice
Le fiamme possono danneggiare l’asciugatrice che
deve pertanto essere installata lontano da cucine a
gas, stufe, termosifoni o piani di cottura.
Se l’elettrodomestico verrà installato sotto un banco
da lavoro, è necessario lasciare uno spazio vuoto
di almeno 10 mm sopra il pannello superiore
dell’elettrodomestico; i pannelli laterali dovranno
invece avere uno spazio libero intorno di almeno 15
mm. In questo modo sarà garantita la circolazione
dell’aria. Controllare che le prese d’aria del pannello
posteriore non siano ostruite.
Assicurarsi inoltre che l’ambiente in cui viene installata
l’asciugatrice non sia umido e che vi sia un
adeguato ricambio di aria.
Aerazione
Questo elettrodomestico asciuga il bucato
immettendo aria fredda, pulita e relativamente
asciutta, riscaldandola e facendola passare attraverso
i tessuti, che vengono così delicatamente asciugati.
Per agevolare l’asciugatura, l’aria umida viene espulsa
dalla parte posteriore attraverso un tubo di aerazione.
È importante che l’ambiente in cui si utilizza
l’asciugatrice sia sufficientemente aerato, così da
evitare il riciclo dei gas combusti da altri apparecchi.
Sistema di aerazione mobile
Quando si utilizza l’asciugatrice con il sistema di
aerazione mobile, è necessario collegare un tubo di
aerazione. Il tubo va fissato saldamente al foro di
ventilazione posteriore dell’asciugatrice (vedere la
sezione Descrizione del prodotto). Se possibile, si
consiglia di fissare il tubo ad uno scarico vicino
all’asciugatrice. Quando non può essere installata in
modo fisso, l’asciugatrice assicurerà comunque ottime
prestazioni facendo passare il tubo di aerazione
attraverso una finestra parzialmente aperta.
Installazione
Descrizione
Avvio e
programmi Bucato
Avvertenze e
suggerimenti
Cura e
manutenzione Ricerca guasti Assistenza
I
15
Aerazione attraverso una finestra aperta
1. L’estremità del tubo
deve essere rivolto verso
il basso, così da evitare
che l’aria calda umida
possa condensarsi nella
stanza o
nell’asciugatrice.
! Assicurarsi che l’asciugatrice sia sufficientemente
ventilata e che l’estremità del tubo di aerazione non
sia rivolto verso il condotto della presa d’aria posteriore.
! Per il corretto funzionamento dell’asciugatrice è
indispensabile montare sempre il tubo di aerazione.
! Controllare che il tubo di aerazione e i condotti
delle prese d’aria non siano ostruiti o intasati.
! Evitare che l’asciugatrice ricicli aria viziata.
! L’uso scorretto dell’asciugatrice può creare il pericolo
di incendio.
! Non scaricare l’aria emessa dall’asciugatrice nello
stesso canale in cui viene scaricato il fumo emesso
da altri apparecchi che bruciano gas o altri
combustibili.
Collegamento elettrico
Prima di inserire la spina nella presa elettrica,
verificare che:
la presa sia dotata di messa a terra
la presa sia in grado di supportare la potenza
massima prevista per l’asciugatrice, così come
indicata sull’etichetta che riporta le prestazioni di
esercizio (vedere la sezione Descrizione del
prodotto)
la tensione di alimentazione sia compresa nei valori
indicati dall’etichetta che riporta le prestazioni di
esercizio (vedere la sezione Descrizione del
prodotto)
la presa sia compatibile con il tipo di spina
dell’asciugatrice. In caso contrario, sostituire la
spina o la presa.
! L’asciugatrice non può essere installata in ambienti
all’aperto, anche se riparati. Può essere molto
pericoloso esporre questo elettrodomestico alla pioggia
o a un temporale.
! Dopo l’installazione dell’elettrodomestico, il cavo e
la spina elettrica devono rimanere a portata di mano.
! Non utilizzare prolunghe.
! Il cavo elettrico non deve essere tagliato né
calpestato.
! Controllare regolarmente il cavo elettrico e, se
necessario, farlo sostituire solo da tecnici qualificati
che installeranno un altro cavo specifico per questo
elettrodomestico (vedere la sezione Assistenza).
Presso i rivenditori autorizzati è possibile acquistare
cavi di ricambio e cavi più lunghi di quelli montati in
fabbrica.
! Il produttore declina ogni responsabilità nei casi in
cui le presenti regole non vengano rispettate.
! Se si nutrono dei dubbi a riguardo, consultare un
elettricista.
Livellamento dell’asciugatrice
L’asciugatrice deve essere installata in piano per
funzionare correttamente.
Dopo aver installato
l’asciugatrice nella
posizione definitiva,
controllare il suo livello
prima da lato a lato,
quindi da davanti a
dietro.
Se l’asciugatrice non è in
piano, utilizzare un
blocco di legno per
sostenerla mentre si
regolano i due piedini
anteriori in alto o in
basso, finché non si
posiziona in piano.
Informazioni preliminari
Una volta installata l’asciugatrice, prima di metterla in
funzione, pulire l’interno del cestello, così da
rimuovere lo sporco che può essersi accumulato
durante il trasporto.
Descrizione del prodotto
16
I
Pannello di controllo
Lato anteriore Lato posteriore
Guida di asciugatura
manopola
PROGRAMMI
manopola
TIMER
pulsante
START
Indicatore
indicatore
luminoso
ATTIVO
Pannello di controllo
Cestello
Numero di
serie e numero
di modello
Filtro
La Guida di asciugatura è una tabella di facile
comprensione che indica il rapporto tra i tipi di
tessuto e le capacità di carico.
La manopola TIMER imposta l’intervallo di tempo che
deve trascorrere prima dell’avvio del programma di
asciugatura. Ruotare la manopola in senso orario fino
a impostare il numero di ore che si desidera attendere
prima dell’avvio dell’asciugatrice; per tornare indietro,
basta ruotare la manopola in senso antiorario (vedere
la sezione Avvio e programmi).
La manopola PROGRAMMI consente di impostare il
programma desiderato: ruotarla in senso orario, mai in
senso antiorario, fino a quando l’indicatore si troverà
sul programma che si desidera selezionare (vedere la
sezione Avvio e programmi).
Il pulsante START avvia il programma di asciugatura
selezionato (vedere la sezione Avvio e programmi).
Il pulsante TEMPERATURA consente di selezionare
la temperatura di asciugatura (vedere la sezione Avvio
e programmi).
FUORI: temperatura ALTA.
DENTRO: temperatura BASSA.
L’avvisatore acustico ALLARME segnala la fine di un
ciclo di asciugatura.
FUORI: avvisatore ACCESO.
DENTRO: avvisatore SPENTO.
L’indicatore luminoso ATTIVO segnala che
l’asciugatrice è in funzione. Premendo il pulsante
START, l’indicatore si illumina e resta attivo fino a
quando viene aperto lo sportello o viene spenta
l’asciugatrice. L’indicatore luminoso resterà attivo
anche in attesa di un avvio temporizzato.
pulsante
TEMPERATURA
pulsante
ALLARME
Presa d’aria
Collegamento per
tubo di aerazione
Attenzione,
alta temperaturan
Prestazioni di
esercizio
Scelta del programma
1. Inserire la spina dell’asciugatrice nella presa di
alimentazione elettrica.
2. Selezionare il bucato in base al tipo di tessuto
(vedere la sezione Bucato).
3. Aprire lo sportello e controllare la corretta
posizione e la pulizia del filtro (vedere la sezione
Manutenzione).
4. Caricare l’elettrodomestico, facendo attenzione
ad evitare che qualche indumento possa
frapporsi tra lo sportello e la relativa guarnizione.
Chiudere lo sportello.
5. Scegliere il programma di asciugatura
controllando la tabella dei programmi (vedere la
sezione Programmi) e le indicazioni riportate per
i diversi tipi di tessuti (vedere la sezione Bucato).
- Impostare la temperatura mediante il pulsante
TEMPERATURA.
- Selezionare un programma o il tempo di
asciugatura, ruotando in senso orario la
manopola PROGRAMMI.
6. Se necessario, impostare un intervallo di tempo
mediante la manopola TIMER.
Installazione
Descrizione
Avvio e
programmi Bucato
Avvertenze e
suggerimenti
Cura e
manutenzione Ricerca guasti Assistenza
I
17
7. Se si desidera disattivare l’avvisatore acustico,
premere il pulsante ALLARME.
8. Premere il pulsante START per avviare il
programma. L’indicatore luminoso ATTIVO si
accende e resta acceso, anche durante
l’eventuale intervallo di tempo impostato con la
manopola TIMER. Questo indicatore si spegnerà
solo quando verrà aperto lo sportello.
Durante il funzionamento, è possibile aprire lo
sportello per estrarre i capi che nel frattempo si
sono asciugati e lasciare asciugare gli altri. Dopo
aver richiuso lo sportello, è necessario ripremere
il pulsante START, per mettere nuovamente in
funzione l’asciugatrice.
9. Circa 10 minuti prima della fine del programma,
viene attivata la fase di asciugatura finale ad aria
fredda, che consente di raffreddare i tessuti: si
consiglia di non estrarre il bucato prima del
completamento di questa fase.
10. La fine del ciclo di asciugatura viene segnalato
dall’avvisatore acustico. Aprire lo sportello,
estrarre il bucato, pulire il filtro e metterlo
nuovamente in posizione (vedere la sezione
Manutenzione).
11. Scollegare l’asciugatrice dalla rete elettrica.
Avvio e programmi
1. Selezionare la TEMPERATURA ALTA
premendo il pulsante TEMPERATURA.
2. Posizionare la manopola PROGRAMMI su
.
3. Premere il pulsante START :
l’indicatore luminoso ATTIVO si
accenderà.
1. Selezionare la TEMPERATURA ALTA
premendo il pulsante TEMPERATURA.
2. Posizionare la manopola PROGRAMMI su
.
3. Premere il pulsante START :
l’indicatore luminoso ATTIVO si
accenderà.
Programmi
Programma
Funzione Impostazione
Note:
Asciugatura
automatica
(medio carico)
Asciuga completamente: i
capi sono pronti per essere
indossati. Per medi carichi
(da 1 a 3 kg) di tessuti di
Cotone , Misto cotone e
poliestere o Sintetico .
!
Impostando la TEMPERATURA
BASSA, questo programma non
riuscirà ad asciugare i capi. Per fibre
Acriliche o piccole quantità,
selezionare il programma
Asciugatura a tempo. Questo
programma può essere utilizzato
anche con carichi maggiori, se è
necessaria solo un’asciugatura di
base.
1. Selezionare TEMPERATURA ALTA
premendo il pulsante
TEMPERATURA.
2. Posizionare la manopola
PROGRAMMI su .
3. Premere il pulsante START :
l’indicatore luminoso ATTIVO si
accenderà .
Asciugatura
automatica
(pieno carico)
Asciuga completamente: i capi
sono pronti per essere indossati.
Per il pieno carico (da 3 a 6 kg)
di tessuti di Cotone .
! Impostando la TEMPERATURA
BASSA, questo programma non
riuscirà ad asciugare i capi. Per
fibre Acriliche o piccole quantità,
selezionare il programma
Asciugatura a tempo. Questo
programma può essere utilizzato
anche con medio carico, se è
sufficiente un’asciugatura di base.
Asciugatura
temporizzata
fino a 120 minuti
Ideale per asciugare i capi
bagnati da stirare, le fibre
acriliche o i piccoli carichi
(meno di 1 kg).
Leggere i tempi di
asciugatura consigliati
(vedere la sezione Bucato).
Attendere sempre il
completamento di questa
fase.
Questa è la fase conclusiva dei
programmi. Circa 10 minuti prima della
fine del ciclo di asciugatura, la manopola
si sposta automaticamente in questa
posizione. Dopo il suono dell’avvisatore
acustico (se selezionato), sarà possibile
estrarre i capi.
Gli elementi che producono
calore si spengono, così da
consentire il raffreddamento
dei capi.
1. Scegliere se impostare la TEMPERATURA
ALTA o, in alternativa, premere il
pulsante TEMPERATURA per impostare
la temperatura BASSA .
2. Posizionare la manopola PROGRAMMI
sul tempo desiderato.
3. Premere il pulsante START :
l’indicatore luminoso ATTIVO si
accenderà.
Stiratura
facile
Fase di
asciugatura
a freddo
Programma breve (dura circa 10
minuti) che ammorbidisce le
fibre dei tessuti così da
agevolarne la stiratura.
!
Non è un programma di
asciugatura (vedere di
seguito).
Programma di stiratura facile
“Stiratura facile” è un breve programma di 10 minuti (8 minuti di riscaldamento seguiti da 2 minuti di asciugatura a
freddo) che gonfia le fibre dei tessuti rimasti immobili per un lungo periodo di tempo. Il ciclo distende le fibre dei
capi in modo da agevolarne la stiratura e la piegatura.
! Questo non è un programma di asciugatura e non va quindi utilizzato con capi ancora bagnati.
Per risultati ottimali:
1. Non caricare il cestello oltre la capacità massima.
I seguenti valori si riferiscono al peso degli indumenti asciutti:
Tessuto Carico massimo
Cotone e Misto cotone 2,5 kg
Sintetico 2 kg
Denim 2 kg
2. Svuotare l’asciugatrice subito dopo la fine del programma; appendere, piegare o stirare i capi per poi
riporli nell’armadio. Se ciò non fosse possibile, ripetere il programma.
L’effetto prodotto dal programma “Stiratura facile” varia da tessuto a tessuto. I migliori effetti si ottengono su tessuti
tradizionali, quali Cotone o Misto cotone; invece, le caratteristiche di tessuti quali le fibre acriliche o il Tencel® non
consentono di ottenere gli stessi risultati.
18
I
Avvio e programmi
Controllo del bucato
Controllare i simboli riportati sulle etichette dei vari
capi, per verificare se l’indumento può essere
introdotto nell’asciugatrice.
Distinguere il bucato in base al tipo di tessuto.
Svuotare la tasche e controllare i bottoni.
Chiudere le lampo e i ganci e allacciare senza
stringere cinture e lacci.
Strizzare gli indumenti per eliminare la maggior
quantità di acqua possibile.
! Non caricare l’asciugatrice con capi totalmente
pieni d’acqua.
Dimensioni massimi di carico
Non caricare il cestello oltre la capacità massima. I
seguenti valori si riferiscono al peso degli indumenti
asciutti:
Fibre naturali: massimo 6 kg
Fibre sintetiche: massimo 3 kg
! NON sovraccaricare l’asciugatrice perché ciò ridurrà
l’efficienza dell’elettrodomestico.
Carico tipo
Indumenti
Camicetta Cotone 150 g
Altro 100 g
Abito Cotone 500 g
Altro 350 g
Jeans 700 g
10 pannolini 1000 g
Camicia Cotone 300 g
Altro 200 g
T-Shirt 125 g
Biancheria da casa
Coperta Cotone 1500 g
(Matrimoniale) Altro 1000 g
Tovaglia grande 700 g
Tovaglia piccola 250 g
Straccio da cucina 100 g
Telo da bagno 700 g
Asciugamano 350 g
Lenzuolo matrimoniale 500 g
Lenzuolo singolo 350 g
Se si mischiano i capi in tessuto sintetico con capi in
cotone, questi ultimi potrebbero risultare ancora
bagnati al termine del ciclo di asciugatura. In questo
caso, avviare un ulteriore breve ciclo di asciugatura.
Etichette con le istruzioni per il lavaggio
Controllare con attenzione le etichette degli
indumenti, specialmente se si tratta della prima volta
che si introduce il capo in un’asciugatrice. Di seguito
sono riportati i simboli più comuni:
Può essere inserito nell’asciugatrice
Non inserire nell’asciugatrice
Asciugare ad alta temperatura
Asciugare a bassa temperatura
Indumenti non adatti al trattamento di
asciugatura
Capi che contengono parti in gomma o materiali
simili, membrane di plastica (cuscini, imbottiture o
impermeabili in PVC) e ogni tipo di tessuto
infiammabile o che contenga sostanze
infiammabili (asciugamani sporche di lacca).
Fibre di vetro (alcuni tipi di tendaggi)
Indumenti completamente asciutti
Tessuti contrassegnati con il simbolo
(vedere la sezione Tessuti particolari), che
possono essere puliti con prodotti speciali di pulizia
domestica. Seguire attentamente le istruzioni.
Elementi troppo voluminosi (piumoni, sacchi a
pelo, cuscini, imbottiture, copriletto e così via), che
si espandono durante l’asciugatura ed impediscono
così all’aria di circolare nell’asciugatrice.
Bucato
Installazione
Descrizione
Avvio e
programmi Bucato
Avvertenze e
suggerimenti
Cura e
manutenzione Ricerca guasti Assistenza
I
19
Tessuti particolari
Coperte e copriletti: tessuti in acrilico (Acilan,
Courtelle, Orion, Dralon) devono essere asciugati
con estrema cura a temperatura BASSA. Non
impostare mai tempi di asciugatura lunghi.
Indumenti con pieghe o plissettati: leggere le
istruzioni di asciugatura fornite dal produttore.
Capi inamidati: non mischiare questi capi con altri
capi non inamidati. Rimuovere la maggiore quantità
possibile della soluzione iniziale prima di inserire i
capi nell’asciugatrice. Non asciugare questi capi per
troppo tempo: l’amido diverrebbe polvere lasciando
gli abiti troppo morbidi e venendo meno la sua stessa
funzione.
Tempi di asciugatura
La tabella riportata di seguito indica i tempi
APPROSSIMATIVI di asciugatura espressi in minuti. I
valori si riferiscono ad indumenti asciutti:
Cotone
Alta temperatura
Tempi di asciugatura dopo lavaggi in lavatrici da 800-1.000 giri al minuto
Mezzo carico Pieno carico
1 kg 2 kg 3 kg 4 kg 5 kg 6 kg
20-30 35-45 45-60 60-70 70-80 80-100
Sintetici
Alta temperatura
Tempi di asciugatura dopo lavaggi in lavatrici a velocità inferiori
Mezzo carico Pieno carico
1 kg 2 kg 3 kg
20-30 35-45 45-60
Acrilico /
Bassa temperatura
Tempi di asciugatura dopo lavaggi in lavatrici a velocità inferiori
Mezzo carico Pieno carico
1 kg 2 kg
25-40 40-60
I tempi sono approssimativi e possono variare in base a:
Quantità di acqua trattenuta dai capi dopo la
centrifuga: le asciugamani e in genere i capi
delicati trattengono molta acqua.
Tessuto: i capi dello stesso tessuto, ma con trama
e spessore differente, avranno sicuramente tempi
di asciugatura diversi.
Quantità di bucato: capi singoli e piccoli carichi,
impiegano più tempo ad asciugarsi.
Asciugatura: se i capi devono essere stirati, è
consigliabile estrarli dall’asciugatrice quando sono
ancora umidi. I capi che devono essere
completamente asciutti, possono invece essere
lasciati più a lungo.
• Temperatura impostata.
Temperatura della stanza: più è bassa la
temperatura della stanza in cui si trova
l’asciugatrice, più tempo sarà necessario per
l’asciugatura degli indumenti.
Volume: alcuni capi voluminosi richiedono
particolare cura nel processo di asciugatura. È
consigliabile rimuovere questi capi, scuoterli e
inserirli nuovamente nell’asciugatrice: questa
operazione deve essere ripetuta diverse volte
durante il ciclo di asciugatura.
! Non asciugare troppo gli indumenti.
L’umidità naturale contenuta nei tessuti serve a
conservarne la morbidezza e la vaporosità.
20
I
Bucato
1 / 1

Ariston AS 60 V Manuale del proprietario

Categoria
Asciugatrici elettriche
Tipo
Manuale del proprietario
Questo manuale è adatto anche per