Dell S520 Projector Guida Rapida

Dell™ | Interactive Projector

S520

Laser Touch Setup Guide

Příručka pro zprovoznění laserového

ukazovátka

Opsætningsguide for Laser Touch

Laser Touch instelgids

Guide d'installation du pointeur laser

Laser-kosketusasetusopas

Laserberührung-Einrichtungsanleitung

Οδηγός εγκατάστασης λέιζερ αφής

Laserberührung-Einrichtungsanleitung

Guida all'installazione di Laser Touch

Installasjonsveiledning for laserberøring

Przewodnik konfiguracji laserowej

funkcji dotykowej

Guia de Instalação do Laser Touch

Guía de configuración de la función táctil del

láser

Installationsguide för Laser Touch

Руководство по установке Laser

Touch

lazer Dokunmatik Kurulum Kılavuzu

S520 Laser Touch QSC_A02-EMEA.book Page 1 Wednesday, May 14, 2014 6:56 PM

S520 Laser Touch QSC_A02-EMEA.book Page 2 Wednesday, May 14, 2014 6:56 PM

Dell™ | Interactive Projector

S520

Laser Touch Setup Guide

S520 Laser Touch QSC_A02-EMEA.book Page 1 Wednesday, May 14, 2014 6:56 PM

About Notes

NOTE: A NOTE indicates important information that helps you make better use of your

projector.

__________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of

Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; Microsoft,

Windows 7, and Windows Vista are trademarks or registered trademarks of Microsoft Corporation

in the United States and/or other countries.

Other trademarks and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in

trademarks and trade names other than its own.

June 2014 P/N 1MK9T Rev. A02

S520 Laser Touch QSC_A02-EMEA.book Page 2 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

3

NOTE: You computer must have the

following minimum system requirements:

Operating System:

• Windows XP Professional service pack 3

32-bit, Windows 7 32-bit/64-bit, and

Windows 8 32-bit/64-bit

• Windows .NET Framework 4.0

installation is required (You can

download it from the Microsoft site)

• MacOS 10.6 and above

Minimum Hardware:

• Windows processor type: Intel Core i3

or above

• MAC processor type: Intel Core i2 duo

or above

• Windows/MAC RAM: 2 GB of RAM

required or more are recommended

• Windows/MAC Min. HDD space: 110 MB

of available hard-disk space

Part A: Install the Whiteboard

1 Install the whiteboard.

NOTE: Refer to "whiteboard installation

instructions".

Set Up Laser Touch on Your Projector

S520 Laser Touch QSC_A02-EMEA.book Page 3 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

4

Part B: Mount the Projector

2 Install the wall mount and the projector.

NOTE: The wall mount is shipped with your

projector. Please refer "wall mount

installation instructions".

NOTE: Project at 87" for a maximum image

size projection or ~84" if you would like to

leave a border around the projector image

for optimal touch experience.

Part C: Attach Laser Curtain Kit

3 Attach the laser curtain kit onto the

whiteboard.

NOTES:

a Attachment is aided with locating pin

and magnets.

b You can also lock the kit in place with a

security screw.

c There is a cover for the laser curtain kit.

(b) Screw

(a)

S520 Laser Touch QSC_A02-EMEA.book Page 4 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

5

Part D: Connect Necessary

Cables

4 Connect power, video, Mini USB, and DC-

to-DC cables to the projector.

5 Connect the power cable to the power

outlet.

6 Connect the DC-to-DC cable to the laser

curtain kit.

2m DC-to-DC cable

S520 Laser Touch QSC_A02-EMEA.book Page 5 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

6

7 Connect the VGA cable to your computer.

NOTE: You can also project the image

through VGA-B and HDMI. Press the left

button on your control panel for auto

searching and selecting the correct input

source.

8 Connect the Mini USB cable to your

computer.

9 Power on the projector by pressing the

power button on the remote control.

MOLEX

5 m Mini USB cable

S520 Laser Touch QSC_A02-EMEA.book Page 6 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

7

Part E: Install the Touch Driver

on Your Computer

10 The TouchDriver install message will pop-

up automatically after you plug in the USB

cable to your computer. Follow the on-

screen instruction to complete setup.

The driver icon will appear in your

computer's notification area if the driver has

installed successfully.

If the Touch driver is not automatically installed,

go to My Computer and run "TouchDriver.exe".

NOTE: You may require administrator-level

access to install the driver. Contact your

network administrator for support.

Part F: Initialize the Touch

Control Function: Auto Adjust

Touch

This is recommended for first-time use, and

necessary when touch screen responds

inaccurately or erratically.

NOTE: You have to project in duplicate or

projector only modes.

11 When executing driver, click the icon.

The following menu appears on-screen.

S520 Laser Touch QSC_A02-EMEA.book Page 7 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

8

Select "Auto adjust touch for this computer"

option to execute the auto "calibration and

touch area" procedure.

If the "auto adjust touch failed" message

prompts, please take the steps below for

troubleshooting, then do auto adjust touch

again.

a Turn lights off or reduce stray light to

whiteboard

b Do not walk in front of or move the

projector

c Adjust focus to sharpen the projected

image

If the "auto adjust touch still failed" message

appears on screen, please change to manual

calibrate touch and manual touch area.

Calibrate Touch by Manual:

Executing driver, click the icon, and go

to Advanced Settings menu, click the

Calibrate touch option to execute the

manual calibrate touch mode.

Touch the target marks on the screen.

(Press the "ESC" key to exit the calibration

process). After the 4

th

point of calibration

is finished, please wait for 2 seconds while

the calibration data is saved.

1

3

4

2

S520 Laser Touch QSC_A02-EMEA.book Page 8 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

9

Touch Area by Manual:

Executing driver, click the icon, and go

to Advanced Settings menu, click the Set

touch area option to execute the manual

calibrate touch mode.

Touch area window will pop up.

Drag the 4 points, in the order of P1 to P4.

The green frame should lie slightly outside

the projected image area and there should

not be any reflected light spot within this

frame. Once you have completed this task,

click "Exit".

S520 Laser Touch QSC_A02-EMEA.book Page 9 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

10

Part G: Touch Sensitivity

Adjust

When laser curtain has been operative for a

long period of time, the sensitivity might be

slightly reduced. Touch sensitivity functions to

re-sensitize the laser curtain by restoring the

initial setting.

Executing driver, click the icon, and go to

Advanced Settings menu, click the Set touch

Sensitivity option to re-sensitize laser curtain

by restoring the initial setting.

Default value for Touch Sensitivity is 4.

Increasing the value increases the Touch

Sensitivity and Decreasing the Touch Sensitivity

values reduces it.

S520 Laser Touch QSC_A02-EMEA.book Page 10 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

11

Part H: Reset All Touch

Settings

When auto or manual "calibrate touch and

touch area" settings still are incorrect, you can

to execute the Reset all touch settings option

to reset all settings to its factory default.

Executing driver, click the icon, and go to

Advanced Settings menu, click the Reset all

touch settings option to re-sensitize laser

curtain by restoring the initial setting.

Part I: Touch Sensor Adjust

When your touch sensor setting is incorrect,

you can to execute the Adjust touch sensor

option to manual adjust touch sensor area.

Executing driver, click the icon, and go to

Advanced Settings menu, click the Adjust

touch sensor option to manual adjust touch

sensor area.

S520 Laser Touch QSC_A02-EMEA.book Page 11 Wednesday, May 14, 2014 6:56 PM

Set Up Laser Touch on Your Projector

12

Touch sensor adjustment instruction screen

shown below appears, and follow the on-

screen instruction to complete settings.

Part J: Install the Workspace

Application Software on Your

Computer

The WorkSpace Application software is

bundled along with the CD that shipped with

your projector. Install the WorkSpace

Application Software and follow the on-screen

instructions to complete the setup. For more

instructions, refer to "WorkSpace Getting

Started Guide".

S520 Laser Touch QSC_A02-EMEA.book Page 12 Wednesday, May 14, 2014 6:56 PM

Troubleshooting

13

Troubleshooting

If you experience problems with Touch, see the following troubleshooting tips. If the problem

persists, contact Dell (see Projector User's Guide Contacting Dell on page 122).

Problem Possible Solution

The touch functionality on the edge or

corner of image is not working.

Please refer to Part F to execute the auto adjust

touch or touch area by manual or project at ~84" if

whiteboard bezel is affecting touch functionality on

the edge of the image.

If there is a big gap between the cursor

and touch point.

Please refer to Part F to execute the auto adjust

touch.

S520 Laser Touch QSC_A02-EMEA.book Page 13 Wednesday, May 14, 2014 6:56 PM

Troubleshooting

14

If the line drawn is not continuos, broken,

or if you encounter problems with the

Touch function in other areas of the

projected image.

1 Check for presence of foreign objects on the

whiteboard.

2 Please refer to Part I to execute the Adjust

touch sensor area.

3 If there is halogen lamp near the projector and

whiteboard, light from the halogen lamp may

affect touch performance. If so,

a Turn off the halogen lamp.

b Shielding the halogen lamp light to

whiteboard or camera.

c Reduce Touch Sensitivity in driver. Doing so

may however affect touch performance at

whiteboard corners.

Problem (continued) Possible Solution (continued)

S520 Laser Touch QSC_A02-EMEA.book Page 14 Wednesday, May 14, 2014 6:56 PM

Dell™ | Interaktivní projektor

S520

Příručka pro zprovoznění laserového ukazovátka

S520 Laser Touch QSC_A02-EMEA.book Page 1 Wednesday, May 14, 2014 6:56 PM

O poznámkách

POZNÁMKA: Slovo POZNÁMKA označuje důležité informace, které vám pomohou projektor

lépe používat.

__________________

Informace uvedené v tomto dokumentu podléhají zminám bez upozorniní.

Jakákoli reprodukce těchto písemných materiálů bez písemného souhlasu společnosti Dell Inc. je

přísně zakázána.

Ochranné známky použité v tomto textu: Dell a logo DELL jsou ochranné známky společnosti Dell

Inc.; Microsoft, Windows 7 a Windows Vista jsou ochranné známky nebo registrované ochranné

známky společnosti Microsoft Corporation v USA a/nebo v dalších zemích.

Ostatní ochranné známky a obchodní názvy použité v tomto dokumentu mohou odkazovat na

majitele těchto známek, názvů nebo jejich produktů. Společnost Dell Inc. se zříká jakýchkoli nároků

na jiné než vlastní obchodní známky a názvy.

Červen 2014 P/N 1MK9T Rev. A02

S520 Laser Touch QSC_A02-EMEA.book Page 2 Wednesday, May 14, 2014 6:56 PM

Připojení laserového ukazovátka k vašemu projektoru a jeho zprovoznění

3

POZNÁMKA: Váš počítač musí splňovat

následující minimální nároky na systém:

Operační systém:

• Operační systém Windows XP

Professional s aktualizací Service Pack 3

32 bitů, operační systém Windows 7 32/

64 bitů a operační systém Windows 8 32/

64 bitů

• Je vyžadována instalace prostředí

Windows .NET Framework 4.0

(k dispozici ke stažení na stránkách

společnosti Microsoft)

• Operační systém MacOS 10.6 a novější

Minimální hardware:

• Typ procesoru Windows: Intel Core i3

nebo výkonnější

• Typ procesoru MAC: Intel Core i2 duo

nebo výkonnější

• Windows/MAC RAM: Vyžadováno 2 GB

paměti RAM, doporučeno více

• Min. prostor na HDD Windows/MAC: 110

MB volného místa na pevném disku

Část A: Instalace bílé tabule

1 Nainstalujte bílou tabuli.

POZNÁMKA: Viz „pokyny pro instalaci bílé

tabule“.

Připojení laserového ukazovátka k vašemu projektoru a jeho

S520 Laser Touch QSC_A02-EMEA.book Page 3 Wednesday, May 14, 2014 6:56 PM

Připojení laserového ukazovátka k vašemu projektoru a jeho zprovoznění

4

Část B: Montáž projektoru

2 Nainstalujte nástěnný držák a projektor.

POZNÁMKA: Nástěnný držák je dodáván s

projektorem. Viz „pokyny pro instalaci

nástěnného držáku“.

POZNÁMKA: Pro dosažení maximální

velikosti obrazu promítejte z 87"; chcete-li,

aby byly okolo obrazu okraje pro optimální

dotykové ovládání, promítejte z ~84".

Část C: Připevnění sady

laserové opony

3 Připevněte sadu laserové opony na bílou

tabuli.

POZNÁMKY:

a Pro usnadnění připevnění je k dispozici

vodící čep a magnety.

b Sadu lze rovněž zajistit na místě

bezpečnostním šroubkem.

c K dispozici je kryt pro sadu laserové

opony.

(b) Šroubek

(a)

S520 Laser Touch QSC_A02-EMEA.book Page 4 Wednesday, May 14, 2014 6:56 PM

La pagina sta caricando ...

Dell S520 Projector Guida Rapida

Questo manuale è adatto anche per

Dell S520 Projector Guida Rapida

in altre lingue

Documenti correlati

Altri documenti