Sony MEX-N5200BT Istruzioni per l'uso

MEX-N5200BT/MEX-N4200BT

4-597-143-23(1)

Bluetooth®

Audio System

Аудиосистема Bluetooth®

Аудіосистема з Bluetooth®

Operating Instructions

GB

Bedienungsanleitung

DE

Mode d’emploi

FR

Istruzioni per l’uso

IT

Gebruiksaanwijzing

NL

Инструкция по

эксплуатации

RU

Інcтpyкції з

eкcплyaтaції

UA

To cancel the demonstration (DEMO) display, see

page 18.

For the connection/installation, see page 33.

Zum Deaktivieren der Demo-Anzeige (DEMO)

schlagen Sie bitte auf Seite 21 nach.

Informationen zum Anschluss und zur Installation

finden Sie auf Seite 37.

Pour annuler la démonstration (DEMO), reportez-

vous à la page 20.

Pour le raccordement/l’installation, reportez-vous à

la page 37.

Per annullare la dimostrazione (DEMO), vedere

pagina 21.

Per l’installazione e i collegamenti, consultare

pagina 36.

Om de demonstratie (DEMO) te annuleren, zie

pagina 20.

Raadpleeg pagina 36 voor meer informatie over de

aansluiting/installatie.

Для отмены демонстрации на дисплее (режим

DEMO) см. стр. 22.

Инструкции по установке/подключению см. на

стр. 39.

Щоб відмінити демонстраційний екран (DEMO),

див. стoр. 22.

Інструкції з підключення/встановлення див. на

стoр. 39.

2GB

Made in Thailand

Laser Diode Properties

 Emission Duration: Continuous

 Laser Output: Less than 53.3 W

(This output is the value measurement at a

distance of 200 mm from the objective lens

surface on the Optical Pick-up Block with

7 mm aperture.)

The nameplate indicating operating voltage,

etc., is located on the bottom of the chassis.

Hereby, Sony Corporation declares that this

equipment is in compliance with Directive

2014/53/EU.

The full text of the EU declaration of

conformity is available at the following

internet address:

http://www.compliance.sony.de/

This equipment is intended to be used with

the approved version(s) of software that are

indicated in the EU Declaration of

Conformity.

The software loaded on this equipment is

verified to comply with the essential

requirements of the Directive 2014/53/EU.

Software version: 1_

The software version can be checked in the

firmware setup item of the general setup

menu.

Notice for customers: the following

information is only applicable to

equipment sold in countries applying

EU Directives

Manufacturer: Sony Corporation, 1-7-1 Konan

Minato-ku Tokyo, 108-0075 Japan

For EU product compliance: Sony Belgium,

bijkantoor van Sony Europe Limited, Da

Vincilaan 7-D1, 1935 Zaventem, Belgium

Disposal of waste batteries

and electrical and electronic

equipment (applicable in

the European Union and

other European countries

with separate collection systems)

This symbol on the product, the battery or

on the packaging indicates that the product

and the battery shall not be treated as

household waste. On certain batteries this

symbol might be used in combination with a

chemical symbol. The chemical symbols for

mercury (Hg) or lead (Pb) are added if the

battery contains more than 0.0005%

mercury or 0.004% lead.

By ensuring these products and batteries

are disposed of correctly, you will help

prevent potentially negative consequences

for the environment and human health

which could otherwise be caused by

inappropriate waste handling. The recycling

of the materials will help to conserve natural

resources.

In case of products that for safety,

performance or data integrity reasons

require a permanent connection with an

incorporated battery, this battery should be

replaced by qualified service staff only.

To ensure that the battery and the electrical

and electronic equipment will be treated

properly, hand over these products at end-

of-life to the applicable collection point for

the recycling of electrical and electronic

equipment.

For all other batteries, please view the

section on how to remove the battery from

the product safely. Hand the battery over to

the applicable collection point for the

recycling of waste batteries.

For more detailed information about

recycling of this product or battery, please

contact your local Civic Office, your

household waste disposal service or the

shop where you purchased the product or

battery.

For safety, be sure to install this unit in the

dashboard of the car as the rear side of

the unit becomes hot during use.

For details, see “Connection/Installation”

(page 33).

3GB

CAUTION

The following frequency 65 – 74 MHz range

is not allocated to sound broadcasting in the

European Common Allocations table and

cannot be used in Europe.

Disclaimer regarding services offered

by third parties

Services offered by third parties may be

changed, suspended, or terminated without

prior notice. Sony does not bear any

responsibility in these sorts of situations.

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR

ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL DAMAGES OR OTHER

DAMAGES INCLUDING, WITHOUT

LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF

THE PRODUCT OR ANY ASSOCIATED

EQUIPMENT, DOWNTIME, AND PURCHASER’S

TIME RELATED TO OR ARISING OUT OF THE

USE OF THIS PRODUCT, ITS HARDWARE

AND/OR ITS SOFTWARE.

Dear customer, this product includes a radio

transmitter.

According to UNECE Regulation no. 10, a

vehicle manufacturers may impose specific

conditions for installation of radio

transmitters into vehicles.

Please check your vehicle operation manual

or contact the manufacturer of your vehicle

or your vehicle dealer, before you install this

product into your vehicle.

Emergency calls

This BLUETOOTH car handsfree and the

electronic device connected to the

handsfree operate using radio signals,

cellular, and landline networks as well as

user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any

electronic device for essential

communications (such as medical

emergencies).

On BLUETOOTH communication

 Microwaves emitting from a BLUETOOTH

device may affect the operation of

electronic medical devices. Turn off this

unit and other BLUETOOTH devices in the

following locations, as it may cause an

accident.

– where inflammable gas is present, in a

hospital, train, airplane, or petrol station

– near automatic doors or a fire alarm

 This unit supports security capabilities that

comply with the BLUETOOTH standard to

provide a secure connection when the

BLUETOOTH wireless technology is used,

but security may not be enough

depending on the setting. Be careful when

communicating using BLUETOOTH wireless

technology.

 We do not take any responsibility for the

leakage of information during BLUETOOTH

communication.

If you have any questions or problems

concerning your unit that are not covered in

this manual, consult your nearest Sony

dealer.

Warning if your car’s ignition has no

ACC position

Be sure to set the AUTO OFF function

(page 19). The unit will shut off completely

and automatically in the set time after the

unit is turned off, which prevents battery

drain. If you do not set the AUTO OFF

function, press and hold OFF until the

display disappears each time you turn the

ignition off.

Important notice

4GB

Table of Contents

Guide to Parts and Controls. . . . . . . . . . . . . 5

Getting Started

Detaching the Front Panel . . . . . . . . . . . . . . 6

Resetting the Unit. . . . . . . . . . . . . . . . . . . . . 6

Setting the Clock. . . . . . . . . . . . . . . . . . . . . . 7

Preparing a BLUETOOTH Device . . . . . . . . . 7

Connecting a USB Device. . . . . . . . . . . . . . . 9

Connecting Other Portable Audio

Device . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Listening to the Radio

Listening to the Radio . . . . . . . . . . . . . . . . 10

Using Radio Data System (RDS). . . . . . . . . . 11

Playback

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . 12

Playing a USB Device . . . . . . . . . . . . . . . . . 12

Playing a BLUETOOTH Device . . . . . . . . . . 12

Searching and Playing Tracks . . . . . . . . . . 13

Handsfree Calling (via

BLUETOOTH only)

Receiving a Call. . . . . . . . . . . . . . . . . . . . . . 14

Making a Call. . . . . . . . . . . . . . . . . . . . . . . . 14

Available Operations during Call. . . . . . . . 15

Useful Functions

SongPal with iPhone/Android smartphone

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using Siri Eyes Free. . . . . . . . . . . . . . . . . . . 17

Settings

Canceling the DEMO Mode . . . . . . . . . . . . 18

Basic Setting Operation . . . . . . . . . . . . . . . 18

General Setup (GENERAL) . . . . . . . . . . . . . 19

Sound Setup (SOUND) . . . . . . . . . . . . . . . . 20

Display Setup (DISPLAY). . . . . . . . . . . . . . . 20

BLUETOOTH Setup (BLUETOOTH) . . . . . . . 21

SongPal Setup (SONGPAL) . . . . . . . . . . . . . 22

Additional Information

Updating the Firmware . . . . . . . . . . . . . . . 22

Precautions. . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . 24

Specifications . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . 27

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Connection/Installation

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Parts List for Installation . . . . . . . . . . . . . . 33

Connection (For MEX-N5200BT) . . . . . . . . 34

Connection (For MEX-N4200BT) . . . . . . . . 35

Installation . . . . . . . . . . . . . . . . . . . . . . . . . 38

5GB

Guide to Parts and Controls

 Front panel release button

 SRC (source)

Turn on the power.

Change the source.

OFF

Press and hold for 1 second to turn the

source off and display the clock.

Press and hold for more than 2 seconds

to turn off the power and the display.

 Control dial

Rotate to adjust the volume.

PUSH ENTER

Enter the selected item.

Press SRC, rotate then press to change

the source (timeout in 2 seconds).

MENU

Open the setup menu.

VOICE (page 15, 17, 18)

Press and hold for more than 2 seconds

to activate voice dial, voice recognition

(Android™ smartphone only), or the Siri

function (iPhone only).

N-Mark

Touch the control dial with Android

smartphone to make BLUETOOTH

connection.

 Disc slot

 Display window

 / (SEEK –/+)

Tune in radio stations automatically.

Press and hold to tune manually.

/ (prev/next)

/ (fast-reverse/fast-forward)

 (disc eject)

 PTY (program type)

Select PTY in RDS.

(browse) (page 13)

Enter the browse mode during playback.

(Not available when a USB device in

Android mode or iPod is connected.)

 CALL

Enter the call menu. Receive/end a call.

Press and hold for more than 2 seconds

to switch the BLUETOOTH signal.

 (back)

Return to the previous display.

MODE (page 7, 10, 15)

 Receptor for the remote commander

 Number buttons (1 to 6)

Receive stored radio stations. Press and

hold to store stations.

Main unit

6GB

ALBUM /

Skip an album for audio device. Press and

hold to skip albums continuously.

(Not available when a USB device in

Android mode or iPod is connected.)

(repeat)

(Not available when a USB device in

Android mode is connected.)

(shuffle)

(Not available when a USB device in

Android mode is connected.)

MIC (page 15)

 (play/pause)

 EXTRA BASS

Reinforce bass sound in synchronization

with the volume level. Press to change

the EXTRA BASS setting: [1], [2], [OFF].

 AUX input jack

 DSPL (display)

Change display items.

SCRL (scroll)

Press and hold to scroll a display item.

 USB port

Detaching the Front Panel

You can detach the front panel of this unit to

prevent theft.

1 Press and hold OFF  until the unit

turns off, press the front panel

release button , then pull the panel

towards you to remove.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel,

the caution alarm will sound for a few

seconds. The alarm will only sound if the

built-in amplifier is used.

Serial numbers

Make sure the serial numbers on the bottom

of the unit and the back of the front panel

are matched correctly. Otherwise you cannot

make BLUETOOTH pairing, connection and

disconnection by NFC.

Resetting the Unit

Before operating the unit for the first time,

or after replacing the car battery or

changing connections, you must reset the

unit.

Getting Started

Attaching the front panel

7GB

1 Press DSPL and (back)/MODE for

more than 2 seconds.

Note

Resetting the unit will erase the clock setting and

some stored contents.

Setting the area/region

After resetting the unit, the area/region

setting display appears.

1 Press ENTER while [SET AREA] is

displayed.

The area/region currently set appears.

2 Rotate the control dial to select

[EUROPE] or [RUSSIA], then press it.

3 Rotate the control dial to select [YES]

or [NO], then press it.

If the setting area/region is changed, the

unit is reset, then the clock is displayed.

This setting can be configured in the general

setup menu (page 19).

Setting the Clock

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

CLOCK-ADJ], then press it.

The hour indication flashes.

3 Rotate the control dial to set the hour

and minute.

To move the digital indication, press

/ (SEEK –/+).

4 After setting the minute, press MENU.

The setup is complete and the clock

starts.

To display the clock

Press DSPL.

Preparing a BLUETOOTH

Device

You can enjoy music, or perform handsfree

calling depending on the BLUETOOTH

compatible device such as a smartphone,

cellular phone and audio device (hereafter

“BLUETOOTH device” if not otherwise

specified). For details on connecting, refer to

the operating instructions supplied with the

device.

Before connecting the device, turn down the

volume of this unit; otherwise, loud sound

may result.

By touching the control dial on the unit with

an NFC* compatible smartphone, the unit is

paired and connected with the smartphone

automatically.

* NFC (Near Field Communication) is a technology

enabling short-range wireless communication

between various devices, such as mobile phones

and IC tags. Thanks to the NFC function, data

communication can be achieved easily just by

touching the relevant symbol or designated

location on NFC compatible devices.

For a smartphone with Android OS 4.0 or

lower installed, downloading the app “NFC

Easy Connect” available at Google Play™ is

required. The app may not be downloadable

in some countries/regions.

1 Activate the NFC function on the

smartphone.

For details, refer to the operating

instructions supplied with the

smartphone.

2 Touch the N-Mark part of the unit

with the N-Mark part of the

smartphone.

Connecting with a Smartphone by

One touch (NFC)

8GB

Make sure that lights up on the display

of the unit.

To disconnect by One touch

Touch the N-Mark part of the unit with the

N-Mark part of the smartphone again.

Notes

• When making the connection, handle the

smartphone carefully to prevent scratches.

• One touch connection is not possible when the

unit is already connected to two NFC compatible

devices. In this case, disconnect either device, and

make connection with the smartphone again.

When connecting a BLUETOOTH device for

the first time, mutual registration (called

“pairing”) is required. Pairing enables this

unit and other devices to recognize each

other. This unit can connect two BLUETOOTH

devices (two cellular phones, or a cellular

phone and an audio device).

1 Place the BLUETOOTH device within

1 m (3 ft) of this unit.

2 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

3 Rotate the control dial to select [SET

PAIRING], then press it.

4 Rotate the control dial to select [SET

DEVICE 1]* or [SET DEVICE 2]*, then

press it.

flashes while the unit is in pairing

standby mode.

* [SET DEVICE 1] or [SET DEVICE 2] will be

changed to the paired device name after

pairing is complete.

5 Perform pairing on the BLUETOOTH

device so it detects this unit.

6 Select [MEX-XXXX] (your model

name) shown in the display of the

BLUETOOTH device.

If your model name does not appear,

repeat from step 2.

7 If passkey* input is required on the

BLUETOOTH device, input [0000].

* Passkey may be called “Passcode,” “PIN code,”

“PIN number” or “Password,” etc., depending

on the device.

When pairing is made, stays lit.

8 Select this unit on the BLUETOOTH

device to establish the BLUETOOTH

connection.

or lights up when the connection is

made.

Note

While connecting to a BLUETOOTH device, this unit

cannot be detected from another device. To enable

detection, enter the pairing mode and search for

this unit from another device.

To start playback

For details, see “Playing a BLUETOOTH

Device” (page 12).

To disconnect the paired device

Perform steps 2 to 4 to disconnect after this

unit and the BLUETOOTH device are paired.

To use a paired device, connection with this

unit is required. Some paired devices will

connect automatically.

Pairing and connecting with a

BLUETOOTH device

Connecting with a paired

BLUETOOTH device

[0000]

Input passkey

9GB

1 Press MENU, rotate the control dial to

select [BLUETOOTH], then press it.

2 Rotate the control dial to select [SET

BT SIGNL], then press it.

Make sure that lights up.

3 Activate the BLUETOOTH function on

the BLUETOOTH device.

4 Operate the BLUETOOTH device to

connect to this unit.

or lights up.

Icons in the display:

To connect the last-connected device

from this unit

Activate the BLUETOOTH function on the

BLUETOOTH device.

To connect with the audio device, press SRC

to select [BT AUDIO] and press  (play/

pause).

To connect with the cellular phone, press

CALL.

Note

While streaming BLUETOOTH audio, you cannot

connect from this unit to the cellular phone.

Connect from the cellular phone to this unit instead.

Tip

With BLUETOOTH signal on: when the ignition is

turned to on, this unit reconnects automatically to

the last-connected cellular phone.

To install the microphone

For details, see “Installing the microphone

(MEX-N5200BT only)” (page 37).

When an iPhone/iPod with iOS5 or later

installed is connected to the USB port, the

unit is paired and connected with the

iPhone/iPod automatically.

To enable BLUETOOTH Auto Pairing, make

sure [SET AUTOPAIR] in [BLUETOOTH] is set

to [ON] (page 21).

1 Activate the BLUETOOTH function on

the iPhone/iPod.

2 Connect an iPhone/iPod to the USB

port.

Make sure that lights up on the display

of the unit.

Notes

• BLUETOOTH Auto Pairing is not possible if the unit

is already connected to two BLUETOOTH devices.

In this case, disconnect either device, then

connect the iPhone/iPod again.

• If BLUETOOTH Auto Pairing is not established, see

“Preparing a BLUETOOTH Device” (page 7).

Connecting a USB Device

1 Turn down the volume on the unit.

2 Connect the USB device to the unit.

To connect an iPod/iPhone, use the USB

connection cable for iPod (not supplied).

Lights up when handsfree calling is

available by enabling the HFP

(Handsfree Profile).

Lights up when the audio device is

playable by enabling the A2DP

(Advanced Audio Distribution

Profile).

Connecting with an iPhone/iPod

(BLUETOOTH Auto Pairing)

10GB

Connecting Other Portable

Audio Device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect the portable audio device to

the AUX input jack (stereo mini jack)

on the unit with a connecting cord

(not supplied)*.

* Be sure to use a straight type plug.

4 Press SRC to select [AUX].

To match the volume level of the

connected device to other sources

Start playback of the portable audio device

at a moderate volume, and set your usual

listening volume on the unit.

Press MENU, then select [SOUND]  [SET AUX

VOL] (page 20).

Listening to the Radio

To listen to the radio, press SRC to select

[TUNER].

1 Press MODE to change the band (FM1,

FM2, FM3, MW or LW).

2 Press MENU, rotate the control dial to

select [GENERAL], then press it.

3 Rotate the control dial to select [SET

BTM], then press it.

The unit stores stations in order of

frequency on the number buttons.

1 Press MODE to change the band (FM1,

FM2, FM3, MW or LW).

2 Perform tuning.

To tune manually

Press and hold / (SEEK –/+) to

locate the approximate frequency, then

press / (SEEK –/+) repeatedly to

finely adjust to the desired frequency.

To tune automatically

Press / (SEEK –/+).

Scanning stops when the unit receives a

station.

1 While receiving the station that you

want to store, press and hold a

number button (1 to 6) until [MEM]

appears.

1 Select the band, then press a number

button (1 to 6).

Listening to the Radio

Storing automatically (BTM)

Tuning

Storing manually

Receiving the stored stations

11GB

Using Radio Data System

(RDS)

AF continuously retunes the station to the

strongest signal in a network, and TA

provides current traffic information or traffic

programs (TP) if received.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

AF/TA], then press it.

3 Rotate the control dial to select [SET

AF-ON], [SET TA-ON], [SET AF/TA-ON]

or [SET AF/TA-OFF], then press it.

To store RDS stations with the AF and

TA setting

You can preset RDS stations along with an

AF/TA setting. Set AF/TA, then store the

station with BTM or manually. If you preset

manually, you can also preset non-RDS

stations.

To receive emergency announcements

With AF or TA on, emergency

announcements will automatically interrupt

the currently selected source.

To adjust the volume level during a

traffic announcement

Level will be stored into memory for

subsequent traffic announcements,

independently from the regular volume

level.

To stay with one regional program

(REGIONAL)

When the AF and REGIONAL functions are

on, you will not be switched to another

regional station with a stronger frequency. If

you leave this regional program’s reception

area, set [SET REG-OFF] in [GENERAL] during

FM reception (page 19).

This function does not work in the UK and

some other areas.

Local Link function (UK only)

This function enables you to select other

local stations in the area, even if they are not

stored on your number buttons.

During FM reception, press a number button

(1 to 6) on which a local station is stored.

Within 5 seconds, press again a number

button of the local station. Repeat this

procedure until the local station is received.

1 Press PTY during FM reception.

2 Rotate the control dial until the

desired program type appears, then

press it.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

The CT data from the RDS transmission sets

the clock.

1 Set [SET CT-ON] in [GENERAL]

(page 19).

Setting alternative frequencies

(AF) and traffic announcement

(TA)

Selecting program types (PTY)

NEWS (News), AFFAIRS (Current Affairs), INFO

(Information), SPORT (Sports), EDUCATE

(Education), DRAMA (Drama), CULTURE

(Culture), SCIENCE (Science), VARIED (Varied),

POP M (Pop Music), ROCK M (Rock Music),

EASY M (M.O.R. Music), LIGHT M (Light

classical), CLASSICS (Serious classical), OTHER

M (Other Music), WEATHER (Weather), FINANCE

(Finance), CHILDREN (Children’s program),

SOCIAL A (Social Affairs), RELIGION (Religion),

PHONE IN (Phone In), TRAVEL (Travel), LEISURE

(Leisure), JAZZ (Jazz Music), COUNTRY (Country

Music), NATION M (National Music), OLDIES

(Oldies Music), FOLK M (Folk Music),

DOCUMENT (Documentary)

Setting clock time (CT)

12GB

Playing a Disc

1 Insert the disc (label side up).

Playback starts automatically.

Playing a USB Device

In these Operating Instructions, “iPod” is

used as a general reference for the iPod

functions on an iPod and iPhone, unless

otherwise specified by the text or

illustrations.

For details on the compatibility of your iPod,

see “About iPod” (page 23) or visit the

support site on the back cover.

AOA (Android Open Accessory) 2.0, MSC

(Mass Storage Class) and MTP (Media

Transfer Protocol) type USB devices*

compliant with the USB standard can be

used. Depending on the USB device, the

Android mode or MSC/MTP mode can be

selected on the unit.

Some digital media players or Android

smartphones may require setting to MTP

mode.

* e.g., a USB flash drive, digital media player,

Android smartphone

Notes

• For details on the compatibility of your USB device,

visit the support site on the back cover.

• Smartphones with Android OS 4.1 or higher

installed support Android Open Accessory 2.0

(AOA 2.0). However, some smartphones may not

fully support AOA 2.0 even if Android OS 4.1 or

higher is installed.

For details on the compatibility of your Android

smartphone, visit the support site on the back

cover.

• Playback of the following files is not supported.

MP3/WMA/FLAC:

– copyright-protected files

– DRM (Digital Rights Management) files

– Multi-channel audio files

MP3/WMA:

– lossless compression files

Before making a connection, select the USB

mode (Android mode or MSC/MTP mode)

depending on the USB device (page 19).

1 Connect a USB device to the USB port

(page 9).

Playback starts.

If a device is already connected, to start

playback, press SRC to select [USB] ([IPD]

appears in the display when the iPod is

recognized).

2 Adjust the volume on this unit.

To stop playback

Press and hold OFF for 1 second.

To remove the device

Stop playback, then remove the device.

Caution for iPhone

When you connect an iPhone via USB,

phone call volume is controlled by the

iPhone, not the unit. Do not inadvertently

increase the volume on the unit during a

call, as a sudden loud sound may result

when the call ends.

Playing a BLUETOOTH Device

You can play contents on a connected

device that supports BLUETOOTH A2DP

(Advanced Audio Distribution Profile).

1 Make BLUETOOTH connection with

the audio device (page 7).

To select the audio device, press MENU,

then select [BLUETOOTH]  [SET

AUDIODEV] (page 21).

2 Press SRC to select [BT AUDIO].

3 Operate the audio device to start

playback.

Playback

13GB

4 Adjust the volume on this unit.

Notes

• Depending on the audio device, information such

as title, track number/time and playback status

may not be displayed on this unit.

• Even if the source is changed on this unit,

playback of the audio device does not stop.

• [BT AUDIO] does not appear in the display while

running the “SongPal” application via the

BLUETOOTH function.

To match the volume level of the

BLUETOOTH device to other sources

Start playback of the BLUETOOTH audio

device at a moderate volume, and set your

usual listening volume on the unit.

Press MENU, then select [SOUND]  [SET BTA

VOL] (page 20).

Searching and Playing

Tracks

Not available when a USB device in Android

mode is connected.

1 During playback, press (repeat) or

(shuffle) repeatedly to select the

desired play mode.

Playback in the selected play mode may

take time to start.

Available play modes differ depending on

the selected sound source.

Not available when a USB device in Android

mode or iPod is connected.

1 During CD or USB playback, press

(browse)* to display the list of search

categories.

When the track list appears, press

(back) repeatedly to display the desired

search category.

* During USB playback, press (browse) for

more than 2 seconds to directly return to the

beginning of the category list.

2 Rotate the control dial to select the

desired search category, then press it

to confirm.

3 Repeat step 2 to search the desired

track.

Playback starts.

To exit the Quick-BrowZer mode

Press (browse).

Not available when a USB device in Android

mode or iPod is connected.

1 Press (browse).

2 Press  (SEEK +).

3 Rotate the control dial to select the

item.

The list is jumped in steps of 10% of the

total number of items.

4 Press ENTER to return to the Quick-

BrowZer mode.

The selected item appears.

5 Rotate the control dial to select the

desired item, then press it.

Playback starts.

Repeat play and shuffle play

Searching a track by name (Quick-

BrowZer™)

Searching by skipping items

(Jump mode)

14GB

To use a cellular phone, connect it with this

unit. You can connect two cellular phones to

the unit. For details, see “Preparing a

BLUETOOTH Device” (page 7).

Receiving a Call

1 Press CALL when a call is received

with a ringtone.

The phone call starts.

Note

The ringtone and talker’s voice are output only from

the front speakers.

To reject the call

Press and hold OFF for 1 second.

To end the call

Press CALL again.

Making a Call

You can make a call from the phonebook or

call history when a cellular phone

supporting PBAP (Phone Book Access

Profile) is connected.

When two cellular phones are connected to

the unit, select either phone.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[PHONE BOOK], then press it.

3 Rotate the control dial to select an

initial from the initial list, then press

it.

4 Rotate the control dial to select a

name from the name list, then press

it.

5 Rotate the control dial to select a

number from the number list, then

press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[RECENT CALL], then press it.

A list of the call history appears.

3 Rotate the control dial to select a

name or phone number from the call

history, then press it.

The phone call starts.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select [DIAL

NUMBER], then press it.

3 Rotate the control dial to enter the

phone number, and lastly select [ ]

(space), then press ENTER*.

The phone call starts.

* To move the digital indication, press /

(SEEK –/+).

Note

[_] appears instead of [#] on the display.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

Handsfree Calling (via

BLUETOOTH only)

From the phonebook

From the call history

By phone number input

By redial

15GB

2 Rotate the control dial to select

[REDIAL], then press it.

The phone call starts.

You can make a call by saying the voice tag

stored in a connected cellular phone that

has a voice dialing function.

1 Press CALL.

When two cellular phones are connected

to the unit, rotate the control dial to

select either phone, then press it.

2 Rotate the control dial to select

[VOICE DIAL], then press it.

Alternatively, press and hold VOICE for

more than 2 seconds.

3 Say the voice tag stored on the

cellular phone.

Your voice is recognized, and the call is

made.

To cancel voice dialing

Press VOICE.

Available Operations during

Call

To adjust the ringtone volume

Rotate the control dial while receiving a call.

To adjust the talker’s voice volume

Rotate the control dial during a call.

To adjust the volume for the other party

(Mic gain adjustment)

Press MIC.

Adjustable volume levels: [MIC-LOW], [MIC-

MID], [MIC-HI].

To reduce echo and noise (Echo

Canceler/Noise Canceler Mode)

Press and hold MIC.

Settable mode: [EC/NC-1], [EC/NC-2].

To switch between handsfree mode

and handheld mode

During a call, press MODE to switch the

phone call audio between the unit and

cellular phone.

Note

Depending on the cellular phone, this operation

may not be available.

By voice tags

16GB

SongPal with iPhone/

Android smartphone

Downloading the latest

version of “SongPal”

application is required

from the App Store for

iPhone or from Google

Play for Android

smartphone.

Notes

• For your safety, follow your

local traffic laws and

regulations, and do not

operate the application

while driving.

• “SongPal” is an app for controlling Sony audio

devices which are compatible with “SongPal”, by

your iPhone/Android smartphone.

• What you can control with “SongPal” varies

depending on the connected device.

• To make use of “SongPal” features, see the details

on your iPhone/Android smartphone.

• For further details on “SongPal,” visit the following

URL: http://rd1.sony.net/help/speaker/songpal/

• Visit the website below and check the compatible

iPhone/Android smartphone models.

For iPhone: visit the App Store

For Android smartphone: visit Google Play

1 Make the BLUETOOTH connection

with iPhone/Android smartphone

(page 7).

To select the audio device, press MENU,

then select [BLUETOOTH]  [SET

AUDIODEV] (page 21).

2 Launch the “SongPal” application.

3 Press MENU, rotate the control dial to

select [SONGPAL], then press it.

4 Rotate the control dial to select

[CONNECT], then press it.

Connection to iPhone/Android

smartphone starts.

For details on the operations on iPhone/

Android smartphone, see the help of the

application.

If the device number appears

Make sure that the number is displayed

(e.g., 123456), then select [Yes] on the

iPhone/Android smartphone.

To terminate connection

1

Press MENU, rotate the control dial to select

[SONGPAL], then press it.

2 Rotate the control dial to select [CONNECT],

then press it.

Selecting the source or application

You can operate to select the desired source

or application on iPhone/Android

smartphone.

To select the source

Press SRC repeatedly. Alternatively, press

SRC, rotate the control dial to select the

desired source, then press ENTER.

To display the source list

Press SRC.

Useful Functions

Establishing the SongPal

connection

17GB

Announcement of various

information by voice guide

(Android smartphone only)

When SMS, Twitter/Facebook/Calendar

notifications, etc., are received, they are

automatically announced through the car

speakers.

For details on settings, refer to the help of the

application.

Activating voice recognition

(Android smartphone only)

By registering applications, you can control

an application by voice command. For

details, refer to the help of the application.

To activate voice recognition

1

Press and hold VOICE to activate voice

recognition.

2 Say the desired voice command into the

microphone when [Say Source or App]

appears on the Android smartphone.

Notes

• Voice recognition may not be available in some

cases.

• Voice recognition may not work properly

depending on the performance of the connected

Android smartphone.

• Operate under conditions where noise such as

engine sound is minimized during voice

recognition.

Replying a message of SMS

(Android smartphone only)

You can reply a message by voice

recognition.

1 Activate voice recognition, then input

“Reply.”

The message input display appears on the

“SongPal” application.

2 Input a reply message by voice recognition.

The list of message candidates appears on the

“SongPal” application.

3 Rotate the control dial to select the desired

message, then press it.

The message is sent out.

Making sound and display settings

You can adjust the settings relating to sound

and display via iPhone/Android

smartphone.

For details on settings, refer to the help of the

application.

Using Siri Eyes Free

Siri Eyes Free allows you to use an iPhone

handsfree by simply speaking into the

microphone. This function requires you to

connect an iPhone to the unit via

BLUETOOTH. Availability is limited to iPhone

4s or later. Make sure that your iPhone is

running the latest iOS version.

You must complete BLUETOOTH registration

and connection configurations for the

iPhone with the unit in advance. For details,

see “Preparing a BLUETOOTH Device”

(page 7). To select the iPhone, press MENU,

then select [BLUETOOTH]  [SET AUDIODEV]

(page 21).

18GB

1 Activate the Siri function on the

iPhone.

For details, refer to the operating

instructions supplied with the iPhone.

2 Press and hold VOICE for more than

2 seconds.

The voice command display appears.

3 After the iPhone beeps, speak into

the microphone.

The iPhone beeps again, then Siri starts

responding.

To deactivate Siri Eyes Free

Press VOICE.

Notes

• The iPhone may not recognize your voice

depending on usage conditions. (For example, if

you are in a moving car.)

• Siri Eyes Free may not function properly, or the

response time may lag in locations where iPhone

signals are difficult to receive.

• Depending on the iPhone’s operating condition,

Siri Eyes Free may not function properly, or may

quit.

• If you play a track with an iPhone using the

BLUETOOTH audio connection, when the track

starts playback via BLUETOOTH, Siri Eyes Free

automatically quits and the unit switches to the

BLUETOOTH audio source.

• When Siri Eyes Free is activated during audio

playback, the unit may switch to the BLUETOOTH

audio source even if you do not specify a track to

play.

• When connecting the iPhone to the USB port, Siri

Eyes Free may not function properly, or may quit.

• When connecting the iPhone to the unit via USB,

do not activate Siri with the iPhone. Siri Eyes Free

may not function properly, or may quit.

• There is no audio sound while Siri Eyes Free is

activated.

Canceling the DEMO Mode

You can cancel the demonstration display

which appears when the source is off and

the clock is displayed.

1 Press MENU, rotate the control dial to

select [GENERAL], then press it.

2 Rotate the control dial to select [SET

DEMO], then press it.

3 Rotate the control dial to select [SET

DEMO-OFF], then press it.

The setting is complete.

4 Press (back) twice.

The display returns to normal reception/

play mode.

Basic Setting Operation

You can set items in the following setup

categories:

General setup (GENERAL), Sound setup

(SOUND), Display setup (DISPLAY),

BLUETOOTH setup (BLUETOOTH), SongPal

setup (SONGPAL)

1 Press MENU.

2 Rotate the control dial to select the

setup category, then press it.

The items that can be set differ

depending on the source and settings.

3 Rotate the control dial to select the

options, then press it.

To return to the previous display

Press (back).

Settings

19GB

General Setup (GENERAL)

AREA

Specifies the area/region to use this unit:

[EUROPE], [RUSSIA].

If the area/region currently set is

changed, this unit is reset, then the clock

is displayed.

(Available only while the source is off and

the clock is displayed.)

DEMO (demonstration)

Activates the demonstration: [ON], [OFF].

CLOCK-ADJ (clock adjust) (page 7)

CAUT ALM (caution alarm)

Activates the caution alarm: [ON], [OFF]

(page 6).

(Available only while the source is off and

the clock is displayed.)

BEEP

Activates the beep sound: [ON], [OFF].

AUTO OFF

Shuts off automatically after a desired

time when the unit is turned off: [ON]

(30 minutes), [OFF].

STEERING

Registers/resets the setting of the

steering wheel remote control.

(Available when connected with the

connection cable (not supplied).)

(Available only while the source is off and

the clock is displayed.)

STR CONTROL (steering control)

Selects the input mode of the connected

remote control. To prevent a malfunction,

be sure to match the input mode with the

connected remote control before use.

CUSTOM

Input mode for the steering wheel

remote control

PRESET

Input mode for the wired remote

control excluding the steering wheel

remote control (automatically selected

when [RESET CUSTOM] is performed.)

EDIT CUSTOM

Registers the functions (SOURCE, ATT,

VOL +/–, SEEK +/–, VOICE, ON HOOK, OFF

HOOK) to the steering wheel remote

control:

 Rotate the control dial to select the

function you want to assign to the

steering wheel remote control, then

press it.

 While [REGISTER] is blinking, press and

hold the button on the steering wheel

remote control you want to assign the

function to. When registration is

complete, [REGISTERED] is displayed.

 To register other functions, repeat

steps  and .

(Available only when [STR CONTROL] is

set to [CUSTOM].)

RESET CUSTOM

Resets the setting of the steering wheel

remote control: [YES], [NO].

(Available only when [STR CONTROL] is

set to [CUSTOM].)

Notes

• While making settings, only button operation

on the unit is available. For safety, park your car

before making this setting.

• If an error occurs while registering, all the

previously-registered information remains.

Restart registration from the function where

the error occurred.

• This function may not be available on some

vehicles. For details on the compatibility of

your vehicle, visit the support site on the back

cover.

USB MODE

Changes the USB mode: [ANDROID],

[MSC/MTP].

(Available only when the USB source is

selected.)

CT (clock time)

Activates the CT function: [ON], [OFF].

AF/TA (alternative frequencies/traffic

announcement)

Selects the alternative frequencies (AF)

and traffic announcement (TA) setting:

[AF-ON], [TA-ON], [AF/TA-ON],

[AF/TA-OFF].

REGIONAL

Restricts reception to a specific region:

[ON], [OFF].

(Available only when FM is received.)

20GB

BTM (best tuning memory) (page 10)

(Available only when the tuner is

selected.)

FIRMWARE

(Available only while the source is off and

the clock is displayed.)

Checks/updates the firmware version. For

details, visit the support site on the back

cover.

FW VERSION (firmware version)

Displays current firmware version.

FW UPDATE (firmware update)

Enters firmware update process: [YES],

[NO].

Updating the firmware takes a few

minutes to complete. During the update,

do not turn the ignition to the OFF

position, nor remove the USB device.

Sound Setup (SOUND)

This setup menu is not available when the

source is off and the clock is displayed.

EQ10 PRESET

Selects an equalizer curve from 10

equalizer curves or off:

[OFF], [R&B], [ROCK], [POP], [HIP-HOP],

[ELECTRONICA], [JAZZ], [SOUL],

[COUNTRY], [KARAOKE]*, [CUSTOM].

The equalizer curve setting can be

memorized for each source.

* [KARAOKE] reduces the vocal sound but

cannot fully remove it during playback. Also,

using a microphone is not supported.

EQ10 CUSTOM

Sets [CUSTOM] of EQ10.

Selects the equalizer curve: [BAND1] 32

Hz, [BAND2] 63 Hz, [BAND3] 125 Hz,

[BAND4] 250 Hz, [BAND5] 500 Hz,

[BAND6] 1 kHz, [BAND7] 2 kHz, [BAND8] 4

kHz, [BAND9] 8 kHz, [BAND10] 16 kHz.

The volume level is adjustable in 1 dB

steps, from -6 dB to +6 dB.

BALANCE

Adjusts the sound balance: [RIGHT-15] –

[CENTER] – [LEFT-15].

FADER

Adjusts the relative level: [FRONT-15] –

[CENTER] – [REAR-15].

S.WOOFER (subwoofer)

SW LEVEL (subwoofer level)

Adjusts the subwoofer volume level:

[+6 dB] – [0 dB] – [-6 dB].

([ATT] is displayed at the lowest setting.)

SW PHASE (subwoofer phase)

Selects the subwoofer phase: [NORM],

[REV].

LPF FREQ (low pass filter frequency)

Selects the subwoofer cut-off frequency:

[80Hz], [100Hz], [120Hz].

HPF FREQ (high pass filter frequency)

Selects the front/rear speaker cut-off

frequency: [OFF], [80Hz], [100Hz], [120Hz].

AUX VOL (AUX volume level)

Adjusts the volume level for each

connected auxiliary device: [+18 dB] –

[0 dB] – [-8 dB].

This setting negates the need to adjust

the volume level between sources.

(Available only when the AUX is selected.)

BTA VOL (BLUETOOTH audio volume level)

Adjusts the volume level for each

connected BLUETOOTH device: [+6 dB] –

[0 dB] – [-6 dB].

This setting negates the need to adjust

the volume level between sources.

(Available only when the BT audio or

application is selected.)

Display Setup (DISPLAY)

DIMMER

Changes the display brightness:

For MEX-N5200BT: [OFF], [ON], [AT] (auto),

[CLK].

([AT] is available only when the

illumination control lead is connected,

and the head light is turned on.)

For MEX-N4200BT: [OFF], [ON], [CLK].

To set this function to be active only

during a fixed period, select [CLK], then

set the start and end times.

La pagina sta caricando ...

Sony MEX-N5200BT Istruzioni per l'uso

Questo manuale è adatto anche per

Sony MEX-N5200BT Istruzioni per l'uso

in altre lingue

Documenti correlati