Hama 00113985 Manuale del proprietario

00

113985

EWS-880

Weather Station

Wetterstation

D

GB

I

CZ

SK

RUS

Operating Instructions

Bedienungsanleitung

Руководство по эксплуатации

Istruzioni per l‘uso

Návod kpoužití

Návod na použitie

M

DST

B

433

THERMO SENSOR

MHz

MADE IN CHINA

RESETCH 123

19

21

20

22

23

A

SNOOZE /LIGHT

ALARM

SET

SENSO RR CC°C °F RESET

DISPL AY

SET

ME MCH

9

15

10

11

12

13

14

16

17

18

M

DST

1

2

3

4

5

7

6

8

2

G Operating instruction

Controls and Displays

ABase station

1. Weather forecast symbol

2. Channel display

3. Outdoor temperature

4. Room temperature

5. Time

6. Measuring station radio symbol

7. Alarm symbol

8. Radio symbol

9. SNOOZE/LIGHT button

=stop the alarm/activate the backlight (approx. 5seconds)

10. ALARM SET button

=display/set alarm mode

11. CH+ button

=select channel/increase the current set value

12. °C/°F slide switch

=switch between °C and °F

13. SENSOR button

=manual search for asignal from the measuring station

14. DISPLAYSET button

=settings/conrm the set value

15. MEM button

=access the saved maximum/minimum values/reduce of the current set value

16. RESET button

=restorefactory settings

17. RCC button

=activate/deactivate manual radio signal reception

18. Battery compartment

BMeasuring station

19. Transmission indicator lamp

20. Opening for wall mounting

21. RESET button =restorefactory settings

22. CH slide switch =channel selection

23. Battery compartment

3

Thank you for choosing aHama product.

Take your time and read the following instructions and information completely.Please keep

these instructions in asafe place for futurereference. If you sell the device, please pass these

operating instructions on to the new owner.

1. Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specic

hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

2. Package Contents

• Weather station EWS-860

(base station for indoors/measuring station for outdoors)

• 4xAA batteries

• These operating instructions

3. Safety Instructions

• The product is intended for private, non-commercial use only.

• Do not operate the product outside the power limits given in the specications.

• Do not use the product in moist environments and avoid splashes.

• Do not use the product in the immediate vicinity of heaters or other heat sources or in

direct sunlight.

• Do not use the product in areas wherethe use of electronic devices is not permitted.

• Do not place the product near interference elds, metal frames, computers, TVs, etc.

Electronic devices and window frames can negatively affect the product’sfunctionality.

• Do not drop the product and do not expose it to any major shocks.

• Do not open the device or continue to operate it if it becomes damaged.

• Do not attempt to service or repair the product yourself.Leave any and allservice work to

qualied experts.

4

• Keep the packaging material out of the reach of children due to the risk of suffocation.

• Dispose of packaging material immediately according to locally applicable regulations.

• Do not modify the product in any way.Doing so voids the warranty.

Warning –Batteries

• Immediately remove and dispose of dead batteries from the product.

• Only use batteries (or rechargeable batteries) that match the specied type.

• Do not mix old and new batteries or batteries of adifferent type or make.

• When inserting batteries, note the correct polarity (+ and -markings) and insert

the batteries accordingly.Failure to do so could result in the batteries leaking or

exploding.

• Do not charge batteries.

• Keep batteries out of the reach of children.

• Do not short circuit the batteries/rechargeable batteries and keep them away from

uncoated metal objects.

4. Getting Started

4.1. Measuring station

• Open the battery compartment (23) and insert two AA batteries with the correct polarity.

• Move the CH slide switch (22) to the left or right to select the channel on which the

measuring station transmits.

• Once the channel is assigned to one transmitter,you can only change it by removing the

batteries or resetting the unit.

• Close the battery compartment.

Note

Beforeuse, ensureyou insert the batteries in the measuring station rst and then in the

base station.

4.2. Base station

• Remove the screen protector from the display.

• Open the battery compartment (18) and insert two AA batteries with the correct polarity.

5

5. Installation

Note –Installation

• We recommend initially placing the base and measuring stations in the intended

locations without installing them and making all the settings described in

6. Operation –todo.

• Only install the stations once the appropriate settings have been made and astable

wireless connection is established.

Note

• The wireless transmission range between the measuring

and base stations is up to 50 minopen spaces.

• Beforeinstallation, ensurethat wireless transmission will not be disrupted by

interference or obstacles like buildings, trees, vehicles, high-voltage lines, etc.

• Beforethe nal installation, ensurethat thereissucient reception between the

intended installation locations.

• When installing the measuring station, ensurethat it is protected from

direct sunlight and rain.

• The international standardheight for measuring air temperature

is 1.25 m(4ft) above ground.

Warning

• Buy special or suitable installation material from aspecialised dealer for wall-mounting.

• Ensurethat no faulty or damaged parts areinstalled.

• Never apply force during installation. This could damage the product.

• Beforeinstallation, ensurethat the chosen wall is suitable for the weight to be

mounted, and make surethat thereare no electrical wires, water,gas or other lines at

the installation site on the wall.

6

5.1. Base station

• Use the base to position the base station on alevel surface.

5.2. Measuring station

• Youcan also position the measuring station on alevel outdoor surface.

• We recommend installing the measuring station securely on an outdoor wall

using the opening (20).

• Install an anchor,screw,nail, etc. in the wall of your choice.

• Hang the measuring station using the opening intended for this purpose (20).

6. Operation

Note –Input

Hold down the CH+ button (11) or the MEM–button (15) to select the values faster.

6.1. Connection to the measuring station

• After you insert the batteries, the base station automatically searches for aconnection to

the measuring station and performs initial setup.

Note

• Initial setup takes approx. 5minutes.

• During connection, the wireless symbol on the measuring station will ash (6).

• Do not press any buttons during setup. Otherwise, values may not be transmitted

correctly and thereisarisk of value errors and inaccuracies.

• The setup process is completed when the indoor (4) and outdoor (3) measurement data

is displayed.

• If the base station still does not receive asignal from the measuring station, press the

SENSOR button (13) to start the manual search for the signal. During the connection

attempt, the measuring station radio symbol (6) will ash.

• During the manual search, press and hold the SENSOR button (13) for approx. 3seconds

to end the search. The radio symbol (6) disappears.

7

6.2. Selecting the channel/other measuring stations

Note

• Youcan install two moremeasuring stations in addition to the included measuring

station. Ensurethat the base and measuring stations areset to the same channel.

Visit www.hama.com for suitable measuring stations.

• Press the CH+ button (11) repeatedly to set the channel to that set on the respective

measuring station –see 4.1. Measuring station. Either 1, 2 or 3 (2) is displayed.

• The base station now shows the data measured (3) on the selected measuring station (2).

• Press and hold the CH+ button (11) to select the channel scan. The measurement values

of the individual measuring stations/channels (2) aredisplayed consecutively for 4seconds

each.

• Press the CH+ button (11) again to return to normal mode.

6.3. Basic and manual settings

Automatic setting using the DCF signal

After the rst time the base station is switched on and successful transmission is established

between the base station and the measuring station, the clock will automatically search for a

DCF signal. During the search, the wireless symbol (8) will ash.

When the radio signal is received, the date and time areautomatically set.

Radio icon Signal strength

No reception

Poor

Fair

Excellent

8

Radio icon Searching for the DCF signal

Flashing display Active

Constant display Successful –signal is being received

No display Error –signal search ended

Note –Time settings

• If,during initial setup of the device, aDCF radio signal is not received within the rst

few minutes, the search is aborted. The radio symbol disappears.

• If thereare reception problems, we recommend leaving the clock to sit overnight, since

interference is generally less at night.

• In the meantime, you can start amanual search for the DCF radio signal at another

location or you can manually set the time and date.

• The clock automatically continues to search for the DCF radio signal on adaily basis

(2:00 a.m., 8:00 a.m., 2:00 p.m. and 8:00 p.m.). If the signal is received successfully,

the manually set time and date areoverwritten.

• Press the RCC button (17) to start the manual search for the DCF radio signal.

Note –Manual search

• The manual search is automatically aborted after 6-16 minutes.

• Using the RCC button (10) frequently will drain the battery.Werecommend only using

this function to seek out an optimal location for the device.

9

Note –Summer time

• The clock automatically switches to summer time.

DST

appears on the display as long

as summer time is activated.

Manually setting

• Press and hold the DISPLAYSET button (14) for approx. 3seconds

to make the following settings one after the other:

• 12/24-hour format (5)

• Hours (5)

• Minutes (5)

• Seconds (only zeros possible) (5)

• Time zone (5)

• To select the individual values, press the CH+ button (11) or the MEM– button (15) and

conrm each selection by pressing the DISPLAYSET button (14).

• If you do not make an entry for 60 seconds, you automatically exit the setup mode.

Note –Time zone

• The DCF signal can be received over long distances, but always transmits the current

Central European Time in Germany.Make sureyou account for the time difference in

countries with another time zone.

• If you areinMoscow,the time is 3hours later than in Germany.This means that you

should set +3 for the time zone. The clock then automatically sets the time to 3hours

after the DCF signal received or relative to the manually set time.

Alarm

• Press and hold the ALARM SET button (10) for approx. 3seconds to set the time of the

alarm displayed. The hours display begins to ash.

• Press the CH+ button (11) or the MEM– button (15) to select the hour for the alarm time

and conrm your selection by pressing the ALARM SET button (10). The minutes display

begins to ash.

• Repeat the process to set the minutes for the alarm time.

• If you do not make an entry for 60 seconds, you automatically exit the setup mode.

• The alarm function is automatically activated when you set the alarm time.

10

• Alternatively,you can press the ALARM SET button (10) to display the alarm time (AL).

• Press the ALARM SET button (10) as needed to activate/deactivate the alarm.

• The alarm symbol (7) will either be displayed or not displayed accordingly.

• When the alarm is triggered, the alarm symbol (7) begins to ash and an alarm sounds.

• Press the ALARM SET button (10) to stop the alarm. Otherwise, it will stop automatically

after 2minutes.

Note –Snooze function

• While the alarm is sounding, press the SNOOZE/LIGHT button (9) to activate the

snooze function. The alarm symbol (7) begins to ash on the display.The alarm is

stopped for 5minutes, after which it will sound again.

• The snooze function can be used over a24-hour period.

Celsius/Fahrenheit

• Move the °C/°F slide switch (12) to the °C or °F position to display the

temperature(3,4) in the respective unit.

6.4 Weather forecast

Note –Weather forecast

• Based on changes in the atmospheric pressureand the data saved, the base station is

able to make weather forecasts for the next 12 to 24 hours.

• The probability of an accurate weather forecast is around 70–75%.

11

• The weather forecast and the current weather areindicated by four different symbols (1):

Symbol (1) Weather

Sun

Slightly cloudy

Cloudy

Rain

6.5. Maximum and minimum temperature and humidity values

• The base station automatically stores the maximum and minimum outdoor/indoor

temperaturevalues.

• Repeatedly press the MEM– button (15) to switch between the current temperature,

minimum temperature(MIN) and maximum temperature(MAX).

• The maximum and minimum values aredisplayed for 5seconds.

• Press and hold the MEM– button (15) to reset the stored maximum and minimum values.

6.6. Frost warning

• If the outdoor temperature(3) is between -2°C and ~3°C, the frost warning symbol

appears on the LCDand ashes continuously.

• The frost warning symbol disappears once the temperaturerises above this range.

12

6.7. Backlight

Note –Backlight

• If you press the SNOOZE/LIGHT button (9), the display will light up for approx. 5seconds.

6.8. Low battery charge

As soon as the battery symbol

appears on the display of the base station, the capacity of

the batteries in the measuring station is very low.Replace the batteries immediately.

Note –Replacing the batteries

• Note that the stations have to be resynchronised each time after you change the

batteries in the measuring or base station.

• To do this, remove the batteries from the other station and then reinsert them, or

change them as required.

6.9. Reset

• If displays/transmissions continually fail to appear or areincorrect, use apointed object

(paper clip, etc.) to press the RESET button (16) on the base station and the RESET button

(21) on the measuring station to carry out arestart.

• The base station returns to the factory settings and all stored information is lost.

7. Care and Maintenance

Only clean this product with aslightly damp, lint-free cloth and do not use aggressive

cleaning agents. Make surethat water does not get into the product.

8. Warranty Disclaimer

Hama GmbH &CoKGassumes no liability and provides no warranty for damage resulting

from improper installation/mounting, improper use of the product or from failuretoobserve

the operating instructions and/or safety notes.

13

9. Service and Support

Please contact Hama Product Consulting if you have any questions about this product.

Hotline: +49 9091 502-115 (German/English)

Further support information can be found here:

www.hama.com

10. Technical Data

Base station Measuring station

Power supply

3.0 V

2xAAbatteries

3.0 V

2xAAbatteries

Measuring range

Temperature

0°C –+45°C/

32°F –+113°F

-40°C –+70°C/

-40°F –+158°F

Measuring increments

Temperature

0,1°C /°F0,1°C /°F

Temperature

measurement cycle

60-64 s60-64 s

Radio-controlled

DCF clock

YesNo

Radio-controlled

DCF clock

YesYes

Max. number of

measuring stations

3

Frequency 433 MHz

Range ≤50m

14

11. Recycling Information

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU and 2006/66/EU

in the national legal system, the following applies: Electric and electronic devices

as well as batteries must not be disposed of with household waste. Consumers are

obliged by law to return electrical and electronic devices as well as batteries at the

end of their service lives to the public collecting points set up for this purpose or

point of sale. Details to this aredened by the national law of the respective country.This

symbol on the product, the instruction manual or the package indicates that aproduct is

subject to these regulations. By recycling, reusing the materials or other forms of utilising old

devices/Batteries, you aremaking an important contribution to protecting our environment.

12. Declaration of Conformity

Hereby,Hama GmbH &CoKGdeclares that the radio equipment type [00113985]

is in compliance with Directive 2014/53/EU.The full text of the EU declaration of

conformity is available at the following internet address:

www.hama.com-> 00113985-> Downloads.

Frequency band(s)

433 MHz

Maximum radio-frequency

power transmitted

0,501 mW

15

Bedienungselemente und Anzeigen

ABasisstation

1. Wettervorhersagesymbol

2. Kanalanzeige

3. Außentemperatur

4. Raumtemperatur

5. Uhrzeit

6. Funksymbol Messstation

7. Alarmsymbol

8. Funksymbol

9. SNOOZE /LIGHT-Taste

=Unterbrechung des Wecksignals /Aktivierung der Hintergrundbeleuchtung

(ca. 5Sekunden)

10. ALARM SET-Taste

=Anzeige/ Einstellung Alarm-Modus

11. CH+-Taste

=Kanalauswahl /Erhöhung des aktuellen Einstellungswertes

12. °C/°F-Schiebeschalter

=Wechsel zwischen °C und °F

13. SENSOR-Taste

=manuelle Suche nach Signal von der Messstation

14. DISPLAYSET-Taste

=Einstellungen /Bestätigung des Einstellungswerts

15. MEM-Taste

=Abruf der gespeicherten Höchst-/ Tiefstwerte /

Verringerung des aktuellen Einstellungswertes

16. RESET-Knopf =Zurücksetzung auf Werkseinstellung

17. RCC-Taste =Aktivierung/ Deaktivierung manueller Funksignal-Empfang

18. Batteriefach

BMessstation

19. Kontrollleuchte Übertragung

20. Aussparung für Wandmontage

21. RESET-Knopf =Zurücksetzung auf Werkseinstellung

22. CH-Schiebeschalter =Kanalauswahl

23. Batteriefach

D Bedienungsanleitung

16

Vielen Dank, dass Sie sich für ein Hama Produkt entschieden haben!

Nehmen Sie sich Zeit und lesen Sie die folgenden Anweisungen und Hinweise zunächst ganz

durch. Bewahren Sie diese Bedienungsanleitung anschließend an einem sicheren Ort auf,um

bei Bedarf darin nachschlagen zu können. Sollten Sie das Gerät veräußern, geben Sie diese

Bedienungsanleitung an den neuen Eigentümer weiter.

1. Erklärung von Warnsymbolen und Hinweisen

Warnung

Wirdverwendet, um Sicherheitshinweise zu kennzeichnen oder um Aufmerksamkeit auf

besondereGefahren und Risiken zu lenken.

Hinweis

Wirdverwendet, um zusätzlich Informationen oder wichtige Hinweise zu kennzeichnen.

2. Packungsinhalt

• Wetterstation EWS-860

(Basisstation für den Innenbereich /Messstation für den Außenbereich)

• 4AABatterien

• diese Bedienungsanleitung

3. Sicherheitshinweise

• Das Produkt ist für den privaten, nicht-gewerblichen Haushaltsgebrauch vorgesehen.

• Betreiben Sie das Produkt nicht außerhalb seiner in den technischen Daten angegebenen

Leistungsgrenzen.

• Verwenden Sie das Produkt nicht in einer feuchten Umgebung und vermeiden Sie

Spritzwasser.

• Betreiben Sie das Produkt nicht in unmittelbarer Nähe der Heizung, anderer Hitzequellen

oder in direkter Sonneneinstrahlung.

• Benutzen Sie das Produkt nicht in Bereichen, in denen elektronische Produkte nicht erlaubt

sind.

• Positionieren Sie das Produkt nicht in der Nähe von Störfeldern, Metallrahmen, Computern

und Fernsehern etc. Elektronische Geräte sowie Fensterrahmen beeinträchtigen die

Funktion des Produktes negativ.

17

• Lassen Sie das Produkt nicht fallen und setzen Sie es keinen heftigen Erschütterungen aus.

• Öffnen Sie das Produkt nicht und betreiben Sie es bei Beschädigungen nicht weiter.

• Versuchen Sie nicht, das Produkt selbst zu warten oder zu reparieren. Überlassen Sie

jegliche Wartungsarbeit dem zuständigen Fachpersonal.

• Halten Sie Kinder unbedingt von dem Verpackungsmaterial fern, es besteht

Erstickungsgefahr.

• Entsorgen Sie das Verpackungsmaterial sofort gemäß den örtlich gültigen

Entsorgungsvorschriften.

• Nehmen Sie keine Veränderungen am Produkt vor.Dadurch verlieren sie jegliche

Gewährleistungsansprüche.

Warnung -Batterien

• Entfernen und entsorgen Sie verbrauchte Batterien unverzüglich aus dem Produkt.

• Verwenden Sie ausschließlich Akkus (oder Batterien), die dem angegebenen Typ

entsprechen.

• Mischen Sie alte und neue Batterien nicht, sowie Batterien unterschiedlichen Typs oder

Herstellers.

• Beachten Sie unbedingt die korrekte Polarität (Beschriftung +und -) der Batterien

und legen Sie diese entsprechend ein. Bei Nichtbeachtung besteht die Gefahr des

Auslaufens oder einer Explosion der Batterien.

• Laden Sie Batterien nicht.

• Bewahren Sie Batterien außerhalb der Reichweite von Kindern auf.

• Schließen Sie Akkus/Batterien nicht kurz und halten Sie sie von blanken

Metallgegenständen fern.

4. Inbetriebnahme

4.1. Messstation

• Öffnen Sie das Batteriefach (23) und legen Sie zwei AA Batterien polrichtig ein.

• Schieben Sie den CH-Schiebeschalter (22) nach links oder rechts, um den Kanal, auf dem

die Messstation sendet, auszuwählen. Sobald der Kanal einem Sender zugewiesen wurde,

kann dieser nur geändert werden, wenn Sie die Batterien entnehmen oder das Basisgerät

zurücksetzen.

• Schließen Sie die Batteriefachabdeckung anschließend.

18

Hinweis

Beachten Sie, dass Sie bei der Inbetriebnahme immer zuerst die Batterien in die

Messstation, und dann in die Basisstation einlegen.

4.2. Basisstation

• Entfernen Sie die Schutzfolie auf dem Display.

• Öffnen Sie das Batteriefach (18) und legen Sie zwei AA Batterien polrichtig ein.

5. Montage

Hinweis –Montage

• Es wirdempfohlen, die Basis- und Messstation zunächst an den gewünschten

Aufstellorten ohne Montage zu platzieren und alle Einstellungen -wie in 6. Betrieb

beschrieben –vorzunehmen.

• Montieren Sieerstnach korrekter Einstellung und stabilerFunkverbindung die Station/en.

Hinweis

• Die Reichweite der Funkübertragung zwischen der Mess- und Basisstation beträgt im

freien Gelände bis zu 50m.

• Achten Sie vor der Montage darauf,dass die Funkübertragung nicht durch Störsignale

oder Hindernisse wie Gebäude, Bäume, Fahrzeuge, Hochspannungsleitungen, u.a.

beeinusst wird.

• Stellen Sie vor der endgültigen Montage sicher,dass zwischen den gewünschten

Aufstellorten ausreichender Empfang besteht.

• Achten Sie bei der Montage der Messstation darauf,dass diese vor direkter Sonne und

Regen geschützt positioniert ist.

• Die internationale Standardhöhe für die Messung der Lufttemperatur beträgt 1,25 m

(4 ft) über Grund.

19

Warnung

• Besorgen Sie sich spezielles bzw.geeignetes Montagematerial im Fachhandel für die

Montage an der vorgesehenen Wand.

• Stellen Sie sicher,dass keine fehlerhaften oder beschädigten Teile montiert werden.

• Wenden Sie bei der Montage niemals Gewalt oder hohe Kräfte an. Diese können das

Produkt beschädigen.

• Prüfen Sie vor Montage die Eignung der vorgesehenen Wand für das anzubringende

Gewicht und vergewissern Sie sich, dass sich an der Montagestelle in der Wand keine

elektrischen Leitungen, Wasser-, Gas- oder sonstige Leitungen benden.

5.1. Basisstation

• Stellen Sie die Basisstation mithilfe des Standfußes auf einer ebenen Fläche auf.

5.2. Messstation

• Die Messstation können Sie ebenfalls auf einer ebenen Fläche im Außenbereich aufstellen.

• Es wirdempfohlen, die Messstation sicher und fest an einer Außenwand mithilfe der

Aussparung (20) zu montieren.

• Befestigen Sie Dübel, Schraube, Nagel, etc. in der dafür vorgesehenen Wand.

• Hängen Sie die Messstation mit der dafür vorgesehenen Aussparung (20) daran ein.

6. Betrieb

Hinweis –Eingabe

Halten Sie die CH+-Taste (11) oder die MEM– -Taste (15) gedrückt, um die Werte

schneller auswählen zu können.

6.1. Verbindung zur Messstation

• Nach dem Einlegen der Batterien sucht die Basisstation automatisch nach einer

Verbindung zur Messstation und führt die Ersteinrichtung durch.

La pagina sta caricando ...

Hama 00113985 Manuale del proprietario

Hama 00113985 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti