Hitachi RAK-18QH8W Manuale utente

– 1 –

ENGLISH

DEUTSCH

FRANÇAISITALIANOESPAÑOL

PORTUGUÊS

E



SPLIT TYPE AIR CONDITIONER

INDOOR UNIT

RAK-18QH8S(W)

RAK-18QH8(W)

RAK-25QH8(W)

RAK-35QH8(W)

RAK-50QH8(W)

RAK-18QH8S(B)

RAK-18QH8(B)

RAK-25QH8(B)

RAK-35QH8(B)

RAK-50QH8(B)

RAK-18QH8S(W)

RAK-18QH8(W)

RAK-25QH8(W)

RAK-35QH8(W)

RAK-50QH8(W)

RAK-18QH8S(B)

RAK-18QH8(B)

RAK-25QH8(B)

RAK-35QH8(B)

RAK-50QH8(B)

MODEL

Instruction Manual_part A.indb 1 6/23/2010 12:10:42 PM

– 2 –

SAFETY PRECAUTION

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit. ●

Pay special attention to signs of “ ● Warning” and “ Caution”. The “Warning” section contains matters which,

if not observed strictly, may cause death or serious injury. The “Caution” section contains matters which may

result in serious consequences if not observed properly. Please observe all instructions strictly to ensure safety.

The sign indicate the following meanings.

●

Make sure to connect earth line.

The sign in the ﬁ gure indicates prohibition.

Indicates the instructions that must be followed.

Please keep this manual after reading.

●

WARNING

PRECAUTIONS DURING INSTALLATION

Do not reconstruct the unit. ●

Water leakage, fault, short circuit or ﬁ re may occur if you reconstruct the unit by

yourself.

Please ask your sales agent or qualiﬁ ed technician for the installation of your unit.

●

Water leakage, short circuit or ﬁ re may occur if you install the unit by yourself.

Please use earth line.

●

Do not place the earth line near water or gas pipes, lightning-conductor, or the earth

line of telephone. Improper installation of earth line may cause electric shock.

Be sure to use the speciﬁ ed piping set for R410A. Otherwise, this may result in

●

broken copper pipes or faults.

A circuit breaker should be installed depending on the mounting site of the unit.

●

Without a circuit breaker, the danger of electric shock exists.

Do not install near location where there is ﬂ ammable gas. The outdoor unit may

●

catch ﬁ re if ﬂ ammable gas leaks around it.

Please ensure smooth ﬂ ow of water when installing the drain hose.

●

CAUTION

PRECAUTIONS DURING OPERATION

Avoid an extended period of direct air ﬂ ow for your health. ●

W

A

R

N

I

N

G

Do not insert a ﬁ nger, a rod or other objects into the air outlet or inlet. As the fan ●

is rotating at a high speed, it will cause injury. Before cleaning, be sure to stop the

operation and turn the breaker OFF.

During thunder storm, disconnect and turn off the circuit breaker.

●

Do not use any conductor as fuse wire, this could cause fatal accident. ●

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

Should abnormal situation arises (like burning smell), please stop operating the ●

unit and turn off the circuit breaker. Contact your agent. Fault, short circuit or ﬁ re

may occur if you continue to operate the unit under abnormal situation.

Please contact your agent for maintenance. Improper self maintenance may cause

●

electric shock and ﬁ re.

Please contact your agent if you need to remove and reinstall the unit. Electric

●

shock or ﬁ re may occur if you remove and reinstall the unit yourself improperly.

If the supply cord is damaged, it must be replaced by the special cord obtainable

●

at authorized service/parts centers.

W

A

R

N

I

N

G

Instruction Manual 1649_indb 2.indb 2 6/28/2010 5:39:23 PM

– 3 –

ENGLISH

PRECAUTIONS DURING OPERATION

Do not attempt to operate the unit with wet hands, this could cause fatal ●

accident.

When operating the unit with burning equipments, regularly ventilate the

●

room to avoid oxygen insufﬁ ciency.

Do not direct the cool air coming out from the air-conditioner panel to face ●

household heating apparatus as this may affect the working of apparatus

such as the electric kettle, oven etc.

Do not use any aerosol or hair sprays near the indoor unit. This chemical

●

can adhere on heat exchanger ﬁ n and blocked the evaporation water ﬂ ow to

drain pan. The water will drop on tangential fan and cause water splashing

out from indoor unit.

Please ensure that outdoor mounting frame is always stable, ﬁ rm and ●

without defect. If not, the outdoor unit may collapse and cause danger.

Do not splash or direct water to the body of the unit when cleaning it as this ●

may cause short circuit.

When operating the unit with the door and windows opened, (the room humidity is always above ●

80%) and with the air deﬂ ector facing down or moving automatically for a long period of time,

water will condense on the air deﬂ ector and drips down occasionally. This will wet your furniture.

Therefore, do not operate under such condition for a long time.

If the amount of heat in the room is above the cooling or heating capability of the unit (for example: ●

more people entering the room, using heating equipments and etc.), the preset room temperature

cannot be achieved.

This appliance is not to be used by children or persons with reduced physical, sensory or mental

●

capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction. Children must be supervised not to play with the appliance.

Do not climb on the outdoor unit or put objects on it. ●

Please switch off the unit and turn off the circuit breaker during cleaning, the ●

high-speed fan inside the unit may cause danger.

Turn off the circuit breaker if the unit is not to be operated for a long period.

●

C

A

U

T

I

O

N

The product shall be operated under the manufacturer speciﬁ cation and ●

not for any other intended use.

Do not put water container (like vase) on the indoor unit to avoid water ●

dripping into the unit. Dripping water will damage the insulator inside the unit

and causes short-circuit.

Do not place plants directly under the air ﬂ ow as it is bad for the plants. ●

Do not hang any laundry onto the moveable panels. ●

The moveable panels may get dislodged and may cause serious injuries.

Instruction Manual 1649_indb 2.indb 3 6/28/2010 5:39:25 PM

– 2 –

INDOOR UNIT

NAMES AND FUNCTIONS OF EACH PART

AIR CLEANSING FILTER

(Refer Instruction manual)

AIR FILTER

To prevent dust from coming into the indoor unit.

(Refer Instruction manual)

FRONT PANEL

MOVEABLE PANEL

It will be open when the air conditioner is operate

and close when the air conditioner is not in operation.

(Occasionally it may not be open during the operating

mode)

HORIZONTAL DEFLECTOR

●

VERTICAL

DEFLECTOR (AIR OUTLET)

(Refer Instruction manual)

INDOOR UNIT INDICATORS

Light indicator showing the operating condition.

(Refer page 3)

REMOTE CONTROLLER

Send out operation signal to the indoor unit. So as to

operate the whole unit.

(Refer Instruction manual)

WIDTH (mm)

795

MODEL

RAK-18QH8(W)

RAK-25QH8(W)

RAK-35QH8(W)

RAK-50QH8(W)

RAK-18QH8(B)

RAK-25QH8(B)

RAK-35QH8(B)

RAK-50QH8(B)

HEIGHT (mm)

295

DEPTH (mm)

198

MODEL NAME AND DIMENSIONS

Air cleansing and deodorizing ﬁ lters are washable and reusable up to 20 times by using vacuum cleaner or●

water rinse under running tap water. Type number for this air cleansing ﬁ lter is <SPX-CFH20>. Please use

this number for ordering when you want to renew it.

Air cleansing ﬁ lter should be cleaned every month or sooner if noticeable loading occurs.

When used

●

overtime, it may loose its deodorizing function. For maximum performance, it is recommended to replace it

every 1 year depending on application requirements.

NOTE

Moveable Panel■

It will open up automatically when the air conditioner is in operation and it will close up automatically when the●

air conditioner stopped operating. Avoid physical adjustments as it may damage the panels’ mechanisms.

Please do not touch the moving panel during operations as it may pinch your ﬁ ngers.

●

Instruction Manual_part A.indb 2 6/23/2010 12:10:43 PM

– 3 –

ENGLISH

INDOOR UNIT INDICATORS

FILTER LAMP

When the device is operated for a total of about 200 hours,

the FILTER lamp lights to indicate that it is time to clean the

ﬁ lter. The lamp goes out when the “

(AUTO SWING)”

button is pressed while the device is on “STANDBY

MODE”.

OPERATION LAMP

This lamp lights during operation.

The OPERATION LAMP ﬂ ashes in the following cases

during heating.

(1) During preheating

For about 2–3 minutes after starting up.

(2) During defrosting

Defrosting will be performed about once every one

hour when frost forms on the heat exchanger of the

outdoor unit, for 5–10 minutes each time.

SIGNAL RECEIVING PORT

TIMER LAMP

This lamp lights when the timer is working.

OPERATION INDICATOR

TEMPORARY SWITCH

Use this switch to start and stop when the remote controller does not work.

By pressing the temporary switch, the operation is done in previously set operation mode.

●

When the operation is done using the temporary switch after the power source is turned off and turn on again,●

the operation is done in automatic mode.

Front panel

Moveable panel

Hand grip point

Lift the front panel ●

Hand grip point

Do not hold the moveable panel●

when the front panel is in either

opened/closed position.

1. Opening up the front panel

Never try to force open/close the moveable panel manually.●

Manually opening or closing the moveable panel may cause breakdowns (The moveable panel will

automatically close or open when the power supply is switched on or switched off and whenever the unit is

in operations or has stopped operating.

CAUTION

Instruction Manual_part A.indb 3 6/23/2010 12:10:43 PM

– 4 –

Minimum Maximum Minimum Maximum

Indoor

Dry bulb °C 21 32 20 27

Wet bulb °C 15 23 12 19

Outdoor

Dry bulb °C 21 43 2 21

Wet bulb °C 15 26 1 15

Note

Avoid to use the room air conditioner for cooling operation when the outside temperature is below -10°C (14°F). ●

The recommended maximum and minimum operating temperatures of the hot and cold sides should be as

below:

Cooling Heating

● Pull toward the down direction.

2. Closing the Front Panel

When front panel is shaky, there is a possibility panel coming off and ●

falling down.

Do not apply extra force on the front panel when it is opened up in the

●

upright position.

Also frequent removal of the front panel from the front cover may

cause damage.

CAUTION

Initially press the left and the right sides of the front ●

panel and ﬁ nally press the central portion until you

hear a clicking sound.

Instruction Manual_part A.indb 4 6/23/2010 12:10:44 PM

– 4 –

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

REMOTE CONTROLLER

This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is●

controlled electronically, the range of control may be shorter.

This unit can be ﬁ xed on a wall using the ﬁ xture provided. Before ﬁ xing it, make sure the indoor unit can be

controlled from the remote controller.

Handle the remote controller with care. Dropping it or getting it wet may compromise its signal transmission●

capability.

After new batteries are inserted into the remote controller, the unit will initially require approximately 10●

seconds to respond to commands and operate.

Signal emitting window/transmission sign

●

Point this window toward the indoor unit when controlling it.

The transmission sign blinks when a signal is sent.

Display

●

This indicates the room temperature selected, current time, timer status, function

and intensity of circulation selected.

START/STOP button ●

Press this button to start operation. Press it again to stop operation.

SLEEP button ●

Use this button to set the sleep timer.

TEMPERATURE buttons

●

Use these buttons to raise or lower the temperature setting. (Keep pressed, and

the value will change more quickly.)

TIME button ●

Use this button to set and check the time and date.

RESET buttons

●

FUNCTION selector ●

Use this button to select the operating mode. Every time you press it, the mode

will change from

(AUTO) to (HEAT) to (DEHUMIDIFY) to (COOL) and

to (FAN) cyclically.

FAN SPEED selector ●

This determines the fan speed. Every time you press this button, the intensity of

circulation will change from

(AUTO) to (HI) to (MED) to (LOW) to

(SILENT) (This button allows selecting the optimal or preferred fan speed for

each operation mode).

AUTO SWING button ●

Controls the angle of the horizontal air deﬂ ector.

EXTENDED AIRFLOW ●

Use this button to deliver faster and more comfortable air-conditioning.

TIMER control ●

Use this button to set the timer.

OFF-TIMER button ● Select the turn OFF time.

ON-TIMER button ● Select the turn ON time.

RESERVE button ● Time setting reservation.

CANCEL button ● Cancel time reservation.

Precautions for Use

Do not put the remote controller in the following places.

●

Under direct sunlight.●

In the vicinity of a heater.●

Handle the remote controller carefully. Do not drop it on the ﬂ oor, and●

protect it from water.

Once the outdoor unit stops, it will not restart for about 3 min

utes (unless

●

you turn the power switch off and on or unplug the power cord and plug it

in again).

This is to protect the device and does not indicate a failure.

If you press the FUNCTION selector button during operation, the de

vice

●

may stop for about 3 minutes for protection.

AUTO

HEAT

DEHUMIDIFY

COOL

FAN

FAN SPEED

SILENT

LOW

MED

HI

SLEEPING

STOP (CANCEL)

START (RESERVE)

START/STOP

TIME

TIMER SET

TIMER SELECTOR

ON TIMER

OFF TIMER

AUTO SWING

EXTENDED AIRFLOW

Instruction Manual 1649_indb 2.indb 4 6/28/2010 5:39:27 PM

– 5 –

ENGLISH

AUTOMATIC OPERATION

The device will automatically determine the mode of operation, HEAT, COOL or DEHUMIDIFY depending on

the current room temperature. The selected mode of operation will change when the room temperature varies.

However the mode of operation will not change when indoor unit connected to multi type outdoor unit.

VARIOUS FUNCTIONS

■ Auto Restart Control

If there is a power failure, operation will be automatically restarted when the power is resumed with previous ●

operation mode and airﬂ ow direction.

(As the operation is not stopped by remote controller.)

If you intend not to continue the operation when the power is resumed, switch off the power supply. ●

When you switch on the circuit breaker, the operation will be automatically restarted with previous operation

mode and airﬂ ow direction.

Note: 1. If you do not require Auto Restart Control, please consult your sales agent or OFF by remote

control.

2. Auto Restart Control is not available when Timer or Sleep Timer mode is set.

As the settings are stored in memory in the remote controller, you ■

only have to press the (START/STOP) button next time.

Press the FUNCTION selector so that the display indicates the

(AUTO) mode of operation.

When AUTO has been selected, the device will automatically

●

determine the mode of operation, HEAT, COOL or

DEHUMIDIFY depending on the current room temperature.

However the mode of operation will not change when indoor

unit connected to multi type outdoor unit.

If the mode automatically selected by the unit is not satisfactory, ●

manually change the mode setting (heat, dehumidify, cool or

fan).

You can raise or lower the temperature setting as necessary by

maximum of 3°C.

Press the temperature button and the

temperature setting will change by 1°C each

time.

The preset temperature and the actual room temperature may

●

vary somewhat depending on conditions.

The display does not indicate the preset temperature in the ●

AUTO mode. If you change the setting, the indoor unit will

produce a beep.

START

STOP

Press the (FAN SPEED) button, AUTO, LOW and SILENT is

available.

Press the (START/STOP) button.

Operation starts with a beep.

Press the button again to stop operation.

1

Instruction Manual 1649_indb 2.indb 5 6/28/2010 5:39:30 PM

– 6 –

HEATING OPERATION

Use the device for heating when the outdoor temperature is under 21°C.●

When it is too warm (over 21°C), the heating function may not work in order to protect the device.

In order to keep reliability of the device, please use this device above -15°C of the outdoor temperature. ●

Press the FUNCTION selector so that the display indicates

(HEAT).

Set the desired FAN SPEED with the (FAN SPEED) button (the

display indicates the setting).

(AUTO) : The fan speed changes automatically according

to the temperature of the air which blows out.

(HI) : Economical as the room will become warm

quickly.

But you may feel a chill at the beginning.

(MED) : Fan speed slow.

(LOW) : Fan speed slower.

(SILENT) : Fan speed ultra slower.

Set the desired room temperature with the TEMPERATURE buttons

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

somewhat depending on conditions.

Press the

(START/STOP) button. Heating operation starts with

a beep. Press the button again to stop operation.

As the settings are stored in memory in the remote controller, y

ou only

■

have to press the (START/STOP) button next time.

START

STOP

■ Defrosting

Defrosting will be performed about once an hour when frost forms on the heat exchange of the outdoor unit, for

5~10 minutes each time.

During defrosting operation, the operation lamp blinks in cycle of 3 seconds on and 0.5 second off.

The maximum time for defrosting is 20 minutes.

However, if it is connected to multi type outdoor unit, the maximum time for defrosting is 15 minutes.

(If the piping length used is longer than usual, frost will likely to form.)

2

3

1

Instruction Manual 1649_indb 2.indb 6 6/28/2010 5:39:31 PM

– 7 –

ENGLISH

DEHUMIDIFYING OPERATION

■ Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room, ●

reducing the room temperature to the preset level.

When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the

temperature setting slightly lower than the current room temperature, regardless of the temperature setting.

The function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower

than the setting temperature.

The preset room temperature may not be reached depending on the number of people present in the room

●

or other room conditions.

Set the desired room temperature with the TEMPERATURE button

(the display indicates the setting).

The range of 20-26˚C is recommended as the room

temperature for dehumidifying.

Press the (START/STOP) button. Dehumidifying operation

starts with a beep. Press the button again to stop operation.

As the settings are stored in memory in the remote controller, you only

■

have to press the (START/STOP) button next time.

START

STOP

Press the FUNCTION selector so that the display indicates

(DEHUMIDIFY).

The FAN SPEED is set at LOW or SILENT.

Use the device for dehumidifying when the room temperature is over 16°C.

When it is under 15°C, the dehumidifying function will not work.

1

2

Instruction Manual 1649_indb 2.indb 7 6/28/2010 5:39:31 PM

– 8 –

COOLING OPERATION

Use the device for cooling when the outdoor temperature is

21

~ 43°C.

If in doors humidity is very high (80%), some dew may form on the air outlet grille of the indoor unit.

Press the FUNCTION selector so that the display indicates

(COOL).

Set the desired FAN SPEED with the

(FAN SPEED) button (the

display indicates the setting).

(AUTO) : The FAN SPEED is HI at ﬁ rst and varies to MED

automatically when the preset temperature has

been reached.

(HI) : Economical as the room will become cool

quickly.

(MED) : Fan speed slow.

(LOW) : Fan speed slower.

(SILENT) : Fan speed ultra slower.

Set the desired room temperature with the TEMPERATURE button

(the display indicates the setting).

The temperature setting and the actual room temperature may vary

some how depending on conditions.

Press the

(START/STOP) button. Cooling operation starts with a

beep. Press the button again to stop operation. The cooling function

does not start if the temperature setting is higher than the current

room temperature (even though the

(OPERATION) lamp lights).

The cooling function will start as soon as you set the temperature

below the current room temperature.

As the settings are stored in memory in the remote controller, you only

■

have to press the (START/STOP) button next time.

START

STOP

2

3

1

Instruction Manual 1649_indb 2.indb 8 6/28/2010 5:39:32 PM

– 9 –

ENGLISH

FAN SPEED (AUTO) ..... When the AUTO fan speed mode is set in the cooling/heating operation:

For the heating operation

The fan speed will automatically change according to the temperature of

●

discharged air.

When the difference of room temperature and setting temperature is large,

●

fan starts to run at HI speed.

When the room temperature reaches setting temperature, fan speed changes ●

to LOW automatically.

When the difference of room temperature and setting temperature is large,

●

fan starts to run at HI speed.

After room temperature reaches the preset temperature, the cooling ●

operation, which changes the fan speed and room temperature to obtain

optimum conditions for natural healthful cooling will be performed.

For the cooling operation

FAN OPERATION

You can use the device simply as an air circulator. Use this function to dry the interior of the indoor unit at the

end of summer.

Press the FUNCTION selector so that the display indicates

(FAN).

Press the

(FAN SPEED) button.

(HI) : The strongest air blow.

(MED) : Fan speed slow.

(LOW) : Fan speed slower.

(SILENT) : Fan speed ultra slower.

Press the

(START/STOP) button. Fan operation starts with a

beep. Press the button again to stop operation.

START

STOP

EXTENDED AIRFLOW

During operations, press the ■ button to select the various operating modes

that will set the preferred air ﬂ ow direction and will also adjust the air ﬂ ow speed to

reach the furthest distance within its range. (During the cooling operating mode, the

air ﬂ ow direction and air ﬂ ow speed will return to their original settings after 3 hours

of operations).

If the ● (EXTENDED AIRFLOW) button is pressed while the AUTO SWING

mode is set, the AUTO SWING mode is cancelled and the EXTENDED AIRFLOW

mode is set.

If the

● (AUTO SWING) button is pressed while the EXTENDED AIRFLOW

mode is set, the EXTENDED AIRFLOW mode is cancelled and the AUTO

SWING mode is set.

If the ● (EXTENDED AIRFLOW) button is pressed when the horizontal air

deﬂ ector stops at your preferred angle, the deﬂ ector will change to EXTENDED

AIRFLOW.

As the angle of the horizontal air deﬂ ector changes, the air may blow directly ●

onto the body.

1

2

Instruction Manual 1649_indb 2.indb 9 6/28/2010 5:39:33 PM

– 10 –

PM

AM

PM

HOW TO SET THE TIMER

The device will turn on (off) and off ●

(on) at the designated times.

The switching occurs ﬁ rst at the ●

preset time that comes earlier.

The arrow mark appearing on the ●

display indicates the sequence of

switching operations.

1 Press the (ON-OFF)

button so that the

(OFF)

mark blinks.

You can set the device to turn off at the

preset time.

After you change the

batteries;

How to Cancel Reservation

Point the signal window of the remote controller toward the indoor unit, and press the (CANCEL) button.

The (RESERVED) sign goes out with a beep and the (TIMER) lamp turns off on the indoor unit.

1 Set the (TIME) button.

1 Press the (OFF-TIMER)

button. The

(OFF) mark blinks on

the display.

2 Set the turn-off time

with the TIMER control

button.

Press the

(RESERVE)

button.

3 Press the (ON-

TIMER) button so that the

(OFF) mark lights and

the

(ON) mark blinks.

NOTE

You can set only one of the OFF-timer,

ON-timer and ON/OFF-timer.

The device will turn on at the ●

designated times.

TIME

OFF TIMER

ON TIMER

RESERVE

CANCEL

AM

PM

AM

1 Press the (ON-TIMER)

button the

(ON) mark blinks

on the display.

Start

Stop

STOP

Time

OFF-Timer

ON-Timer

ON/OFF Timer

Instruction Manual 1649_indb 2.indb 10 6/28/2010 5:39:34 PM

– 11 –

ENGLISH

3 Point the signal window of the remote controller toward the indoor unit, and press

the

(RESERVE) button.

The

(OFF) mark starts lighting instead of ﬂ ashing and the sign (RESERVED)

lights. A beep occurs and the

(TIMER) lamp lights on the indoor unit.

The time indication will disappear ●

automatically in 10 second.

To check the current time setting, ●

press the

(TIME) button

twice.

The setting of the current time is

now complete.

The timer may be used in three ways: off-timer, on-timer, and on/off (off/on)-timer. Set the current time at ﬁ rst●

because it serves as a reference.

As the time settings are stored in memory in the remote controller, you only have to press the

● (RESERVE)

button in order to use the same settings next time.

2 Press the

(TIME) b

utton.

3 Set the current time with the

TIMER control button.

Example: The current time is 1:30 p.m.

2 Set the turn-off time with

the TIMER control button.

The setting of turn-off time is now complete.

Example: The device will turn off at 11:00p.m.

Example:

The device will turn on at 7:00 a.m.

The setting of the turn-on time is now complete.

4 Set the turn-on time with

the TIMER control button.

5 Point the signal window of the remote controller toward the indoor unit, and

press the

(RESERVE) button.

The

(ON) mark starts lighting instead of ﬂ ashing and the (RESERVED) sign

lights. A beep occurs and the

(TIMER) lamp lights on the indoor unit.

3 Point the signal window of the remote controller toward the indoor unit, and

press the

(RESERVE) button.

The

(ON) mark starts lighting instead of ﬂ ashing and the (RESERVED) sign

lights. A beep occurs and the

(TIMER) lamp lights on the indoor unit.

2 Set the turn-on time with

the TIMER control button.

Example:

The device will turn off at 10:30 p.m. and it will be turned on

at 7:00 a.m.

The settings of the turn-on/off times are now complete.

4 Press the (TIME) button again.

The time indication starts lighting instead of

ﬂ ashing.

AM

PM

AM

PM

AM

PM

AM

PM

AM

PM

AM

Instruction Manual 1649_indb 2.indb 11 6/28/2010 5:39:35 PM

– 12 –

HOW TO SET THE SLEEP TIMER

1 Set the ON-timer.

Set the current time at ﬁ rst if it is not set before (see the pages for setting the current time). Press the

(SLEEP) b

utton, and the display changes as shown below.

Mode

Sleep timer

Indication

1 hour 2 hours 3 hours 7 hours

Sleep timer off

44 44

1

Sleep Timer: The device will continue working for the designated

number of hours and then turn off.

Point the signal window of the remote controller toward the indoor unit,

and press the SLEEP button.

The timer information will be displayed on the remote controller. The

TIMER lamp lights with a beep from the indoor unit. When the sleep

timer has been set, the display indicates the turn-off time.

Example: If you set 3 hours sleep

time at 11:38 p.m., the turn-off time

is 2:38 a.m.

2 Press the (SLEEP) button and set the sleep timer.

The device will be turned off by the sleep timer

and turned on by on-timer.

How to Cancel Reservation

Point the signal window of the remote controller toward the indoor unit, and press the (CANCEL) button.

The (RESERVED) sign goes out with a beep and the (TIMER) lamp turns off on the indoor unit.

For heating:

In this case, the device will turn off in

2 hours (at 1:38 a.m.) and it will be

turned on 6:00 next morning.

H

AM

H

AM

SLEEP

Sleep

timer

Start

Instruction Manual 1649_indb 2.indb 12 6/28/2010 5:39:37 PM

– 13 –

ENGLISH

HOW TO EXCHANGE THE BATTERIES IN THE REMOTE CONTROLLER

Remove the cover as shown in the ﬁ gure and take out the old

batteries.

=

Install the new batteries.

The direction of the batteries should match the marks in the case.

Do not use new and old batteries, or different kinds of batteries1.

together.

Take out the batteries when you do not use the remote controller for2.

2 or 3 months.

CAUTION

CIRCUIT BREAKER

When you do not use the room air conditioner, set the circuit breaker to “OFF”.

TEMPORARY SWITCH

If the remote controller does not work due to battery failure, press this switch to start and stop operation.

This temporary operation will be at the setting made most recently. (The unit will immediately go into automatic

●

operation once power is switched on.)

Push and pull to the

direction of arrow

1

2

Instruction Manual 1649_indb 2.indb 13 6/28/2010 5:39:37 PM

– 14 –

Suitable Room Temperature Install curtain or blinds

Ventilation Effective Usage Of Timer

Do Not Forget To Clean The Air Filter

Please Adjust Suitable Temperature

For Baby And Children

Warning

Freezing temperature

is bad for health and

a waste of electric

power.

It is possible

to reduce heat

entering the

room through

windows.

At night, please use the “OFF or ON timer

operation mode”, together with your wake up

time in the morning. This will enable you to

enjoy a comfortable room temperature. Please

use the timer effectively.

Dusty air ﬁ lter will reduce the air volume and

the cooling efﬁ ciency. To prevent from wasting

electric energy, please clean the ﬁ lter every 2

weeks.

Please pay attention to the room temperature

and air ﬂ ow direction when operating the unit

for baby, children and old folks who have

difﬁ culty in movement.

Caution

Do not close the room for a long period

of time. Occasionally open the door and

windows to

allow the

entrance of

fresh air.

THE IDEAL WAYS OF OPERATION

Instruction Manual 1649_indb 2.indb 14 6/28/2010 5:39:38 PM

– 15 –

ENGLISH

FOR USER’S INFORMATION

The Air Conditioner And The Heat Source In The Room

Not Operating For A Long Time

When Lightning Occurs

Caution

If the amount of heat in the room is above the cooling

capability of the air conditioner (for example: more

people entering the room, using heating equipments

and etc.), the preset room temperature cannot be

achieved.

When the indoor unit is not to be used for a long

period of time, please switch off the power from the

mains. If the power from mains remains “ON”, the

indoor unit still consumes about 8W in the operation

control circuit even if it is in “OFF” mode.

Warning

To protect the whole unit during lightning, please

stop operating the unit and remove the plug from the

socket.

Interference From Electrical Products

Caution

To avoid noise interference, please place the indoor

unit and its remote controller at least 1m away from

electrical products.

OFF

TV

Inverter-type

ﬂ uorescent

lamp

To prevent

interference,

place at least

1m away.

Instruction Manual 1649_indb 2.indb 15 6/28/2010 5:39:39 PM

– 16 –

ATTACHING THE AIR CLEANSING FILTERS

Cleaning and maintenance must be carried out only by qualiﬁ ed service personal. Before cleaning, stop

operation and switch off the power supply.

CAUTION

Claws

(4 places)

Open the front panel.

Pull up the front panel by holding it at both sides with ●

both hands.

Remove the ﬁ lter.

Push upward to release the claws and pull out the

●

ﬁ lter.

Attaching the air cleansing ﬁ lters to the ﬁ lter.

Attach the air cleansing ﬁ lters to the frame by

●

gently compress its both sides and release after

insertion into ﬁ lter frame.

Attach the ﬁ lters.

Attach the ﬁ lters by ensuring that the surface written

●

“FRONT” is facing front.

After attaching the ﬁ lters, push the front panel at three ●

arrow portion as shown in ﬁ gure and close it.

CAUTION

Do not bend the air cleansing

ﬁ lter as it may cause damage to

the structure.

NOTE

In case of removing the air cleansing ﬁ lters, please follow the above procedures. ●

The cooling capacity is slightly weakened and the cooling speed becomes slower when the air cleansing ●

ﬁ lters are used. So, set the fan speed to "HIGH" when using it in this condition.

Do not operate the air conditioner without ﬁ lter. Dust may enter the air conditioner and fault may occur.

●

1

2

3

4

Instruction Manual 1649_indb 2.indb 16 6/28/2010 5:39:40 PM

– 17 –

ENGLISH

MAINTENANCE

Cleaning and maintenance must be carried out only by qualiﬁ ed service personal. Before

cleaning, stop operation and switch off the power supply.

1. AIR FILTER

Clean the air ﬁ lter, as it removes dust inside the room. In case the air ﬁ lter is full of dust, the air ﬂ ow will

decrease and the cooling capacity will be reduced. Further, noise may occur. Be sure to clean the ﬁ lter

following the procedure below.

CAUTION

Open the front panel and remove the ﬁ lter

Gently lift and remove the air cleansing ﬁ lter

●

from the air ﬁ lter frame.

Vacuum dust from the air ﬁ lter and air cleansing

ﬁ lter using vacuum cleaner. If there is too much

dust, air ﬁ lter only rinse under running tap water

and gently brush it with soft bristle brush. Allow

ﬁ lters to dry in shade.

Re-insert the air cleansing ﬁ lter to the ﬁ

lter

●

frame. Set the ﬁ lter with “FRONT” mark facing

front, and slot them into the original state.

After attaching the ﬁ lters, push the front panel●

at three arrow portions as shown in ﬁ gure and

close it.

CAUTION

Do not wash with hot water at more than 40°C. The ﬁ lter may shrink.●

When washing it, shake off moisture completely and dry it in the shade; do not expose it directly to the sun. ●

The ﬁ lter may shrink.

Do not use detergent on the air cleansing ﬁ lter as some detergent may deteriorate the ﬁ

lter electrostatic

●

performance.

PROCEDURE

1

2

3

Instruction Manual 1649_indb 2.indb 17 6/28/2010 5:39:45 PM

La pagina sta caricando ...

Hitachi RAK-18QH8W Manuale utente

Hitachi RAK-18QH8W Manuale utente

in altre lingue

Documenti correlati

Altri documenti