Ubiquiti airFiber 5X AF-5X Manuale utente

Marca: Ubiquiti

Modello: airFiber 5X AF-5X

Categoria: Networking

Tipo: Manuale utente

Questo manuale è adatto anche per

airFiber AF-5X

DATA

MGMT

GPS

LINK

DATA

MGMT

GPS

LINK

5 GHz Carrier

Backhaul Radio

Model: AF-5X

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

airFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Table of Contents

Chapter 1: Overview ................................................1

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Package Contents ................................................................1

airFiber Configuration Interface SystemRequirements ............................1

Hardware Overview ..............................................................1

Chapter 2: Installation ..............................................3

Installation Requirements ........................................................3

Installation Overview .............................................................3

Connecting Power over Ethernet ..................................................3

airFiber Configuration ............................................................4

Hardware Installation .............................................................5

Alignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installer Compliance Responsibility ..............................................10

Chapter 3: Navigation .............................................11

Accessing the airFiber Configuration Interface ...................................11

Product Verification .............................................................12

Interface Tabs ...................................................................12

Chapter 4: Main Tab ...............................................13

Status ...........................................................................13

Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Monitor .........................................................................15

Chapter 5: Wireless Tab ............................................16

Basic Wireless Settings ...........................................................16

Frequency Settings ..............................................................17

Wireless Security ................................................................18

Chapter 6: Network Tab ...........................................19

Management Network Settings ..................................................19

Chapter 7: Advanced Tab ..........................................21

Wireless Settings ................................................................21

DATA Port Ethernet Settings .....................................................21

MGMT Port Ethernet Settings ....................................................23

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

airFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Chapter 8: Services Tab ...........................................24

Ping Watchdog ..................................................................24

SNMP Agent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Telnet Server ....................................................................26

NTP Client .......................................................................26

Dynamic DNS ...................................................................26

System Log ......................................................................26

Device Discovery ................................................................26

Chapter 9: System Tab ............................................27

Firmware Update ................................................................27

Device ..........................................................................28

Date Settings ....................................................................28

System Accounts ................................................................28

Miscellaneous ...................................................................28

Location ........................................................................29

Device Maintenance .............................................................29

Configuration Management .....................................................29

Chapter 10: Tools ..................................................30

Align Antenna ...................................................................30

Discovery .......................................................................31

Ping .............................................................................31

Traceroute ......................................................................31

airView ..........................................................................31

Appendix A: Specifications ........................................35

Appendix B: Safety Notices ........................................36

Electrical Safety Information .....................................................36

Appendix C: Warranty .............................................37

Limited Warranty ................................................................37

Appendix D: Compliance Information .............................39

Installer Compliance Responsibility ..............................................39

FCC

.............................................................................39

Industry Canada

.................................................................39

RF Exposure Warning ............................................................40

Australia and New Zealand ......................................................40

CE Marking ......................................................................40

Frequency Ranges and Power Levels per Country/Region

........................41

RoHS/WEEE Compliance Statement

..............................................44

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

iii

airFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Appendix E: Declaration of Conformity ............................45

Appendix F: Contact Information ..................................46

Ubiquiti Networks Support ......................................................46

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 1: OverviewairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Hardware Overview

Port Cover

LED

Panel

Connects to

External GPS

Antenna

Chain 0:

Connects to

+45° on

airFiber Antenna

Chain 1:

Connects to

-45° on

airFiber Antenna

Chapter 1: Overview

Introduction

Thank you for purchasing the Ubiquiti Networks®

airFiber® AF-5X 5GHz Carrier Backhaul Radio. This User

Guide is for use with airFiber model AF-5X, and provides

installation instructions, explains how to set up an airFiber

link, and shows how to access and use the airFiber

Configuration Interface.

Package Contents

airFiber AF-5X GPS Antenna

Mount

External GPS Antenna Metal Strap

GHz Carrier

Backhaul Radio

Model: AF-5X

DATA

MGMT

GPS

LINK

DATA

MGMT

GPS

LINK

Cable Ties

(Qty. 2)

airFiber PoE Adapter

with Mounting Bracket

(24V, 1A)

Power Cord Quick Start Guide

earth grounding must be used as conditions of product warranty. TOUGHCable

™

is designed for

outdoor installations. It is the customer’s responsibility to follow local country regulations, including

operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS)

requirements.

airFiber Configuration Interface

SystemRequirements

• Microsoft Windows 7, Windows 8; Linux; or Mac OS X

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Apple Safari, Google

Chrome, or Microsoft Internet Explorer 8 (or above)

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 1: OverviewairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Ports

Reset

Button

Management

Port

Data

Port

Management Port 10/100 Mbps, secured Ethernet

port for configuration. In-Band Management is enabled

by default in the airFiber Configuration Interface. When

In-Band Management is disabled, the MGMT port is the

only port that can monitor, configure, and/or update

firmware.

Reset Button To reset to factory defaults, press and hold

the Reset button for more than 10 seconds while the

device is already poweredon.

Data Port Gigabit PoE port for handling all user traffic

and powering the device.

LEDs

Signal LEDs

Signal 4 LED will light blue when on.

Signal 3 LED will light green when on.

Signal 2 LED will light yellow when on.

Signal 1 LED will light red when on.

Bootup to airOS When powering on, the Power, GPS,

LINK, and Signal 1-4 LEDs light on. Once the CPU code

takes over, the GPS, LINK, and Signal 1-3 LEDs turn off.

Signal 4 LED remains on to indicate the boot sequence is

underway.

Initializing airFiber Software When the airFiber

application begins to boot under airOS, the Signal 4 LED

goes from solidly on to a 2.5 Hz flash. This continues until

the AF-5X is fully booted.

Signal Level Once fully booted, the Signal 1-4 LEDs act

as a bar graph showing how close the AF-5X is to ideal

aiming. This is auto-scaled based on the link range, the

antenna gains, and the configured TX power of the

remote AF-5X. Each Signal LED has three possible states:

On, Flashing, and Off. All Signal LEDs would be solidly on in

an ideal link. If the link has a 1 dB loss, the Signal4 LED will

flash; a 2 dB loss and the Signal 4 LED will turn off. The full

bar graph LED states are shown below.

loss

0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13

1 F 0 0 0 0 0 0 0 0 0 0 0 0

1 1 1 F 0 0 0 0 0 0 0 0 0 0

1 1 1 1 1 F F 0 0 0 0 0 0 0

1 1 1 1 1 1 1 1 1 1 F F F 0

0 = Off, 1 = On, F = Flashing

Additional LEDs

LED State Status

LINK

Off RF Off

Short Flash* Syncing

Normal Flash* Beaconing

Long Flash* Registering

On Operational

GPS

Off No GPS Synchronization

Normal Flash* Non-Operational (Weak Signal)

On Operational (Strong Signal)

MGMT

Off No Ethernet Link

On Ethernet Link Established

Random Flashing Ethernet Activity

DATA

Off No Ethernet Link

On Ethernet Link Established

Random Flashing Ethernet Activity

Off No Power

On Powered On

* Short Flash (1:3 on/off cycle)

Normal Flash (1:1 on/off cycle)

Long Flash (3:1 on/off cycle)

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Chapter 2: Installation

Installation Requirements

The airFiber AF-5X radio operates only with an airFiber

antenna or a retrofitted RocketDish™ antenna.

airFiber antenna models:

• AF-5G23-S45

• AF-5G30-S45

• AF-5G34-S45

Retrofit accessory for RocketDish (RD-5G30/RD-5G34):

• AF-5G-OMT-S45

See the antenna’s Quick Start Guide for antenna

installation instructions.

Other Requirements

• Clear line of sight between airFiber radios

• Clear view of the sky for proper GPS operation

• Vertical mounting orientation

• Mounting point:

• At least 1 m below the highest point on the structure

• For tower installations, at least 3 m below the top of

thetower

• Ground wires – min. 10 AWG (5 mm

) and max. length:

1m. Asa safety precaution, ground the airFiber radio to

grounded masts, poles, towers, or grounding bars.

WARNING: Failure to properly ground your

airFiber radio will void your warranty.

• (Recommended) 2 Outdoor Gigabit PoE surge protectors

Note: For guidelines about grounding and

lightning protection, follow your local electrical

regulatory codes.

• Outdoor, shielded Category 6 (or above) cabling and

shielded RJ-45 connectors are required for all wired

Ethernet connections.

Installation Overview

We recommend that you configure your paired airFiber

AF-5X radios before site installation. Below is an overview

of the installation with specific details in the following

instructions:

• Connect Power over Ethernet to the DATA port, and

connect an Ethernet cable between your computer and

the MGMTport.

• Configure the device settings in the airFiber

Configuration Interface.

• Install a ground wire and mount the AF-5X on an

airFiber compatible antenna.

• At the installation site, install the dish antenna (see the

antenna’s Quick Start Guide for installation instructions).

• Secure the ground wire and mount the GPS antenna.

• Establish and optimize the RF link.

Connecting Power over Ethernet

1. Lift the release latch on the bottom of the AF-5X and

slide the Port Cover off.

2. Connect an Ethernet cable to the DATA port.

3. Connect the Ethernet cable from the DATA port to the

Ethernet port labeled POE on the airFiber PoE Adapter.

WARNING: Use only the included airFiber PoE

adapter, Model: GP-H240-100G-4. Failure to do

so can damage the unit and void the product

warranty.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

4. Connect the Power Cord to the power port on the

airFiber PoE Adapter. Connect the other end of the

Power Cord to a powersource.

airFiber Configuration

The instructions in this section explain how to access

the airFiber Configuration Interface and configure the

following settings:

• Wireless Mode Configure one AF-5X as the Master and

the other as the Slave.

• Frequency Setting The operating Frequency must be

the same on both the Master and the Slave.

1. Connect an Ethernet cable from your computer to the

MGMT port on the AF-5X.

2. Configure the Ethernet adapter on your computer with

a static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type http://192.168.1.20 in

the address field and press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the

Username and Password fields. Select your Country and

Language. You must agree to the Terms of Use to use

the product. Click Login.

Note: U.S. product versions are locked to the U.S.

Country Code to ensure compliance with FCC

regulations.

5. The Main tab will appear. Click the Tools drop-down

and select Link Calculator. This tool will guide you

on how to best minimize bandwidth and power/

interference issues.

6. Enter the requirements of your link, and then click

Calculate. Adjust the values as needed to get the

optimal result, and then write down the settings

needed for your configuration.

7. Click the Wireless tab.

8. Configure the Basic Wireless Settings:

a. For one AF-5X, select Master as the Wireless Mode. For

the other AF‑5X, keep the default,Slave.

b. Enter a name in the Link Name field. This should be the

same on both the Master and the Slave.

c. If needed, change the Channel Bandwidth, (Master) Duty

Cycle, Output Power and/or Maximum Modulation Rate

settings.

9. Configure the Frequency Settings. The selected

Frequency must be the same on both airFiber radios.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

10. Configure the Wireless Security:

a. Select the AES Key Type, HEX or ASCII.

b. For the Key field:

- HEX Enter 16 bytes (eight, 16-bit HEX values: 0-9, A-F,

or a-f). You can omit zeroes and use colons, similar to

the IPv6 format.

Note: The airFiber Configuration Interface

supports IPv6 formats excluding dotted quad

and "::" (double-colon) notation.

- ASCII Enter a combination of alphanumeric

characters (0-9, A-Z, or a-z).

11. Click Change and then click Apply.

12. In-Band Management is enabled by default, so each

airFiber radio must have a unique IP Address. (If the

airFiber radios use the same IP Address, you may lose

access to the airFiber radios via the DATA ports.) Click

the Network tab.

a. For the Management IP Address option:

- DHCP Keep the default, DHCP, to use DHCP

reservation on your router to assign a unique IP

Address.

- Static Change the IP Address, Netmask, and other

settings to make them compatible with your network.

b. Click Change and then click Apply.

Repeat the instructions in the airFiber Configuration

section on your other AF-5X. After you have configured

the airFiber radios, disconnect them and move them to

your installation site.

Hardware Installation

Install a Ground Wire

1. Remove the nut from the Ground Bonding Point located

on the back of the AF-5X.

Ground

Bonding

Point

2. Attach a ground wire (min. 10 AWG or 5 mm

) to the

lug and replace the nut to secure the wire.

3. At the installation site, secure the other end of the

ground wire to a grounded mast, pole, tower, or

grounding bar.

WARNING: Failure to properly ground your

airFiber radio will void your warranty.

Note: The ground wire should be as short as

possible and no longer than one meter in

length.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Mount to an Antenna

The AF-5X can be mounted to an airFiber antenna or a

retrofitted RocketDish. The airFiber Dish Antenna

(AF-5G30-S45) is shown in the following steps:

1. Attach the AF-5X to the mounting bracket.

a. Align the mounting tabs on the back of the AF-5X

with the mounting bracket.

b. Slide the AF-5X down to lock it into place.

2. Attach the RF cables from the antenna feed to the RF

connectors on the AF-5X in this combination: +45°to

Chain 0 and -45° to Chain 1.

3. Attach the External GPS Antenna to the RF connector

labeled GPS. Then, place the magnetic External GPS

Antenna on the bracket (this is temporary; you will

mount the External GPS Antenna on the GPS Antenna

Mount at the site).

4. Attach the protective shroud.

a. Align the hash mark on the top of the shroud with the

notch on the dish antenna.

b. Rotate the shroud clockwise until it locks into place.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Mount the External GPS Antenna

Locate a mounting point that has a clear view to the sky,

and is above and as far away as possible from the AF-5X.

1. Attach the GPS Antenna Mount to the pole using the

metal strap, or attach it to a wall using the appropriate

fasteners (notincluded).

2. Place the External GPS Antenna on the mount.

3. Secure the cable of the External GPS Antenna to the

mount with a Cable Tie.

Connecting Power over Ethernet

1. Lift the release latch on the bottom of the AF-5X and

slide the Port Cover off.

2. Connect an outdoor, shielded Ethernet cable to the

DATA port.

3. Connect the other end of the cable from the DATA port

to the Ethernet port labeled POE on the airFiber PoE

Adapter.

WARNING: Use only the included airFiber PoE

adapter, Model: GP-H240-100G-4. Failure to do

so can damage the unit and void the product

warranty.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

4. Connect an Ethernet cable from your network to the

Ethernet port labeled LAN on the airFiber PoE Adapter.

5. Connect the Power Cord to the power port on the

airFiber PoE Adapter. Connect the other end of the

Power Cord to a power source.

Mount the PoE Adapter (Optional)

1. Remove the Mounting Bracket from the adapter by

sliding the bracket downward.

2. Place the Mounting Bracket at the desired location and

mark the holes for the fasteners. Pre-drill the holes if

necessary, then secure the bracket to wall using two

fasteners (not included).

3. Attach the airFiber PoE Adapter to the bracket by

aligning the four slots and tabs, and then slide the

adapter downward.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Surge Protection

For added protection, install two surge suppressors, such

as the Ubiquiti Ethernet Surge Protector, model ETH-SP,

at the end of each link. Install the first surge protector

within one meter of the airFiber DATA port, and install the

second surge protector at the ingress point of the location

housing the wired network equipment.

Ground to Pole, Tower,

or Grounding Block:

Max. 1 m from AF-5X

Max. 1 m

airFiber

PoE Adapter

EdgeRouter

™

Power Source

ETH-SP

GPS Antenna

ETH-SP

AF-5X

Mounted on

AF-5G30-S45

Alignment

Tips

• To accurately align the airFiber radios for best

performance, you MUST align only one end of the link at

a time.

• You may need to use additional hardware to

compensate for issues such as the improper orientation

of a mounting pole or significant elevation differences

between airFiber radios.

Establishing a Link

Adjust the positions of the Master and the Slave to

establish a link. The following guide features the airFiber

antenna, AF-5G30-S45:

Note: The Master must be aimed first at the Slave

because the Slave does not transmit any RF signal

until it detects transmissions from the Master.

1. Master Visually aim the Master at the Slave. To adjust

the Master’s position:

a. Loosen the four pole clamp nuts, and rotate the

airFiber antenna on the pole to align the azimuth.

b. Loosen the six elevation bolts, and use the hex nut on

the elevation rod to adjust the elevation.

Note: Do NOT make simultaneous adjustments on

the Master and Slave.

2. Slave Visually aim the Slave at the Master. To adjust the

Slave’s position:

a. Loosen the four pole clamp nuts, and rotate the

airFiber antenna on the pole to align the azimuth.

b. Loosen the six elevation bolts, and use the hex nut on

the elevation rod to adjust the elevation.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 2: InstallationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

3. Check to see if a link is established. Ensure that the LINK

LED is solidly lit green and the Signal LEDs of the Slave

are displaying signal levels.

4. Slave Aim the Slave at the Master to achieve the

strongest signal level on the Master.

Note: Refer to “Signal LEDs” on page 2 for

details on the signal values.

Note: Maximum signal strength can best be

achieved by iteratively sweeping through both

azimuth and elevation.

5. Master Aim the Master at the Slave to achieve the

strongest signal level on the Slave.

6. Repeat steps 4 and 5 until you achieve an optimal link,

with all four Signal LEDs solidly lit. This ensures the best

possible data rate between the airFiber radios.

7. Lock the alignment on both airFiber antennas by

tightening all the nuts and bolts.

8. Observe the Signal LEDs of each airFiber radio

to ensure that the values remain constant while

tightening the nuts and bolts. If any LED value changes

during the locking process, loosen the nuts and bolts,

finalize the alignment of each airFiber antenna again,

and retighten the nuts and bolts.

Refer to the following chapters of this User Guide for

details on the airFiber Configuration Interface:

• “Main Tab” on page 13

• “Wireless Tab” on page 16

• “Network Tab” on page 19

• “Advanced Tab” on page 21

• “Services Tab” on page 24

• “System Tab” on page 27

• “Tools” on page 30

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer’s responsibility to make sure the

device is operated within local country regulatory

requirements.

The Output Power, Antenna Gain, Cable Loss, and Frequency

fields are provided to the professional installer to assist in

meeting regulatory requirements.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 3: NavigationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Chapter 3: Navigation

The airFiber Configuration Interface is an advanced

operating system capable of powerful wireless and

routing features, built upon a simple and intuitive user

interface foundation.

The AF-5X uses the airFiber Configuration Interface for

easy configuration and management via a web browser.

There are two ways to access the airFiber Configuration

Interface:

• Management Port Enabled by default. Use a direct

connection to the Management port for out-of-band

management.

• In-Band Management Enabled by default. In-band

management is available through the local Data port

or the Data port at the other end of the link. You can

disable it on the Network tab. (See “Management

Network Settings” on page 19 for more details.)

Accessing the airFiber Configuration

Interface

Connect to the airFiber Configuration Interface.

1. Make sure that your host machine is connected to the

LAN that is connected to the Management port on the

AF-5X.

2. Configure the Ethernet adapter on your host system

with a static IP address on the 192.168.1.x subnet (for

example, 192.168.1.100).

3. Launch your web browser. Type http://192.168.1.20 in

the address field and press enter (PC) or return (Mac).

4. Upon initial login, the Terms of Use appear on the login

screen. Enter ubnt in the Username and Password fields,

and select the appropriate choices from the Country

and Language drop-down lists. Check the box next to

Iagree to these terms of use, and click Login.

Note: U.S. product versions are locked to the U.S.

Country Code to ensure compliance with FCC

regulations.

5. The airFiber Configuration Interface will appear,

allowing you to customize your settings as needed.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 3: NavigationairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Product Verification

The airFiber Configuration Interface will verify whether a

product is genuine or counterfeit.

For a genuine airFiber AF-5X, the airFiber Configuration

Interface will display a Genuine Product logo in the lower

left corner of the screen.

For any product that is not an official Ubiquiti product, the

airFiber Configuration Interface will display a counterfeit

warning. Please contact Ubiquiti at [email protected]

regarding this product.

Note: For product models introduced prior to 2012,

the airFiber Configuration Interface will NOT display

any logo in the lower left corner of the screen.

Interface Tabs

The airFiber Configuration Interface contains six main tabs,

each of which provides a web-based management page

to configure a specific aspect of the AF-5X. This User Guide

covers each tab with a chapter. For details on a specific

tab, refer to the appropriate chapter.

• Main The “Main Tab” on page 13 displays device

status, statistics, and network monitoring links.

• Wireless The “Wireless Tab” on page 16 configures

basic wireless settings, including the wireless mode, link

name, frequency, output power, speed, and wireless

security.

• Network The “Network Tab” on page 19 configures

the management network settings, Internet Protocol (IP)

settings, management VLAN, and automatic IP aliasing.

• Advanced The “Advanced Tab” on page 21

provides more precise wireless interface controls,

including advanced wireless settings and advanced

Ethernet settings.

• Services The “Services Tab” on page 24 configures

system management services: Ping Watchdog, Simple

Network Management Protocol (SNMP), servers (web,

SSH, telnet), Network Time Protocol (NTP) client,

Dynamic Domain Name System (DDNS) client, system

log, and device discovery.

• System The “System Tab” on page 27 controls

system maintenance routines, administrator account

management, location management, device

customization, firmware update, and configuration

backup. You can also change the language of the web

management interface.

Each page also contains network administration and

monitoring tools:

• “Align Antenna” on page 30

• “Discovery” on page 31

• “Ping” on page 31

• “Traceroute” on page 31

• “airView” on page 31

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 4: Main TabairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Chapter 4: Main Tab

The Main tab displays a summary of the link status

information, current values of the basic configuration

settings, network settings and information, and traffic

statistics.

Status

Device Name Displays the customizable name or

identifier of the device. The Device Name (also known

as host name) is displayed in registration screens and

discovery tools.

Operating Mode Displays the mode of the AF-5X: Slave,

Master, or Reset.

RF Link Status Displays the status of the AF-5X: RFOff,

Syncing, Beaconing, Registering, Enabling, Listening,

Operational, DFS CAC, or RADAR Detected.

Note: Most of the RF Link Statuses map to specific

flash rates of the Link Status LED (See “LEDs” on

page 2 for more details.)

Status Flash Rate of LED

RF Off Off

Syncing

DFS countries only:

• DFS CAC

• RADAR Detected

Short Flash (1:3 on/off cycle)

Beaconing Normal Flash (1:1 on/off cycle)

Registering Long Flash (3:1 on/off cycle)

Operational On

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 4: Main TabairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

When the AF-5X operates in a DFS country, it performs a

Channel Availability Check (CAC) before operating. The

rules vary by country and frequency, but in general:

• FCC domains If the AF-5X operates in the DFS band (5.4

GHz band), then the following rule applies:

• If the TX and RX Frequencies are the same, then the

AF-5X performs a 60-second check on the Masteronly.

• If the TX and RX Frequencies are different, then the

AF-5X performs a 60-second check on both the Master

and Slave.

• ETSI domains For most frequencies, the AF-5X

performs a 60-second check on the Master and Slave;

however, if it operates in the 5600-5650 MHz range, then

the AF-5X performs a 10-minute check.

While the AF-5X is performing this check, the RF Link Status

displays DFS CAC, and the RF Link Timeout is displayed.

If radar is detected, the RF Link Status displays RADAR

Detected, and the RF Link Timeout is displayed.

RF Link Timeout (Available only if the RF Link Status is

DFS CAC or RADAR Detected.) During the DFS CAC or RADAR

Detected state, the RF Link Timeout counts down the time

remaining before the AF-5X can move to the next RF link

state.

Link Name Displays the name of your link.

Security AES-128 is enabled at all times.

Version Displays the airFiber Configuration Interface

software version.

Uptime This is the total time the device has been running

since the latest reboot (when the device was powered up)

or software upgrade. The time is displayed in days, hours,

minutes, and seconds.

Link Uptime This is the total time the airFiber link has

been continuously operational. The time is displayed in

days, hours, minutes, and seconds.

Remote MAC Displays the Management Ethernet MAC

address of the remote AF-5X.

Remote IP Displays the Management Ethernet IP address

of the remote AF-5X.

Date Displays the current system date and time. The

date and time are displayed in YEAR-MONTH-DAY

HOURS:MINUTES:SECONDS format. The system date and

time is retrieved from the Internet using NTP (Network

Time Protocol). The NTP Client is enabled by default on

the Services tab. The AF-5X doesn’t have an internal clock,

and the date and time may be inaccurate if the NTP Client

is disabled or the device isn’t connected to the Internet.

Frequency Displays the current frequency. The AF-5X

uses the radio frequency specified to transmit and

receivedata.

Channel Width Size of the channel in MHz.

Duty Cycle Displays the duty cycle.

Regulatory Domain Displays the regulatory domain

(FCC/IC, ETSI, or Other), as determined by country

selection.

Chain 0/1 Signal Strength Displays the absolute power

level (in dBm) of the received signal for each chain.

The software calculates the proper signal strength based

on the measured distance and power levels, and then it

scales the Signal Strength bar graphs so that when the link

is aimed correctly, the bar graphs are full-scale. If the bar

graphs are not full-scale, then they indicate that your link

is not optimally aimed.

Remote Chain 0/1 Signal Strength Displays the absolute

power level (in dBm) of the received signal for each chain

of the remote AF-5X. The bar graphs will display as full-

scale once the link is aimed correctly.

Local Modulation Rate Displays the modulation rate:

• 8x (256QAM MIMO)

• 6x (64QAM MIMO)

• 4x (16QAM MIMO)

• 2x (QPSK MIMO)

• 1x (½ Rate QPSK xRT

™

• ¼x (¼ Rate QPSK xRT)

*xtreme Range Technology

If Automatic Rate Adaptation is enabled on the Wireless

tab, then Local Modulation Rate displays the current speed

in use and depends on the Maximum Modulation Rate

specified on the Wireless tab and current link conditions.

Remote Modulation Rate Displays the modulation rate

of the remote AF-5X:

• 8x (256QAM MIMO)

• 6x (64QAM MIMO)

• 4x (16QAM MIMO)

• 2x (QPSK MIMO)

• 1x (½ Rate QPSK xRT)

• ¼x (¼ Rate QPSK xRT)

TX Capacity Displays the potential TX throughput,

how much the AF-5X can send, after accounting for the

modulation and error rates.

RX Capacity Displays the potential RX throughput, how

much the AF-5X can receive, after accounting for the

modulation and error rates.

TX Power (EIRP) Displays the current average transmit

output power (in dBm) of the AF-5X.

Note: If “(Limited)” is displayed, then the transmit

output power has been limited to a value less than

the selected value, to comply with regulatory region

requirements. For a list of maximum output power

values by country and region, refer to “Frequency

Ranges and Power Levels per Country/Region” on

page 41.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 4: Main TabairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Remote TX Power (EIRP) Displays the current average

transmit output power (in dBm) of the remote AF-5X.

Distance Displays the distance between the airFiber

radios.

GPS Signal Quality Displays Global Positioning System

(GPS) signal quality as a percentage value on a scale of

0-100%.

Latitude/Longitude Based on GPS tracking, reports the

device’s current latitude and longitude. Clicking the link

opens the reported latitude and longitude in a browser

using Google Maps

™

(http://maps.google.com).

Altitude Based on GPS tracking, reports the device’s

current altitude relative to sea level.

Synchronization airFiber uses GPS to synchronize the

timing of its transmissions. By default, this option is

disabled.

Ethernet

MGMT MAC Displays the MAC address of the

Management port.

MGMT Displays the speed and duplex of the Management

port.

DATA Displays the speed and duplex of the Data port.

DATA Cable Length Displays the Ethernet cable length

from radio to remote port. This is displayed only for cables

longer than 20 m.

DATA Pair 0 (Pins 1,2) If the cable is functioning properly,

displays the SNR of the twisted pair; if the cable has a

fault, displays the fault (“open” or “short”) and the distance

at which the fault has occurred. If the remote port is

administratively shut down, this field displays “normal”.

DATA Pair 1 (Pins 3,6) If the cable is functioning properly,

displays the SNR of the twisted pair; if the cable has a

fault, displays the fault (“open” or “short”) and the distance

at which the fault has occurred. If the remote port is

administratively shut down, this field displays “normal”.

DATA Pair 2 (Pins 4,5) If the cable is functioning properly,

displays the SNR of the twisted pair; if the cable has a

fault, displays the fault (“open” or “short”) and the distance

at which the fault has occurred. If the remote port is

administratively shut down, this field displays “normal”.

DATA Pair 3 (Pins 7,8) If the cable is functioning properly,

displays the SNR of the twisted pair; if the cable has a

fault, displays the fault (“open” or “short”) and the distance

at which the fault has occurred. If the remote port is

administratively shut down, this field displays “normal”.

Monitor

There are two monitoring tools accessible via the links

on the Main tab. The default is Performance, which is

displayed when you first open the Main tab.

Performance

Throughput and Capacity charts display the current and

potential data traffic.

Throughput

Throughput displays the current data traffic on the Data

port in both graphical and numerical form. The chart scale

and throughput dimension (Bps, Kbps, Mbps) change

dynamically depending on the mean throughput value.

The statistics are updated automatically.

Capacity

Capacity displays the potential data traffic on the Data

port in both graphical and numerical form. The chart scale

and throughput dimension (Bps, Kbps, Mbps) change

dynamically depending on the mean throughput value.

The statistics are updated automatically.

Refresh If there is a delay in the automatic update, click

Refresh to manually update the statistics.

Log

When logging is enabled (see “System Log” on page

26 to enable logging), this option lists all registered

system events. By default, logging is not enabled.

Clear To delete all entries in the system log, click Clear.

Refresh To update the log content, click Refresh.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

Chapter 5: Wireless TabairFiber

AF-5X User Guide

Ubiquiti Networks, Inc.

Chapter 5: Wireless Tab

The Wireless tab contains options to set up the wireless

part of the link. This includes wireless mode, link name,

frequencies, output power, speed, and wireless security.

Change To save or test your changes, click Change.

A new message appears. You have three options:

• Apply To immediately save your changes, click Apply.

• Test To try the changes without saving them, click

Test. To keep the changes, click Apply. If you do not

click Apply within 180 seconds (the countdown is

displayed), the AF-5X times out and resumes its earlier

configuration.

• Discard To cancel your changes, click Discard.

Write down the settings you configure on the Wireless

tab. You will need to enter the same settings on the AF-5X

at the other end of your PtP link. The exceptions are as

follows:

• Wireless Mode Configure one AF-5X as the Master and

the other as the Slave.

Basic Wireless Settings

In this section, configure the basic wireless settings, such

as wireless mode, link name, country code, frequencies,

output power, speed, and gain.

Wireless Mode By default, the Wireless Mode is Slave. You

must configure one AF-5X as Master because each PtP

link must have one Master.

Link Name Enter a name for your PtP link. This name

must be the same on both Master and Slave radios in

order for them to connect.

Country Code Each country has its own power level and

frequency regulations. To ensure the airFiber AF‑5X operates

under the necessary regulatory compliance rules, you must

select the country where your device will be used. The

frequency settings and output power limits will be tuned

according to the regulations of the selected country. For

details, refer to this table, “Frequency Ranges and Power

Levels per Country/Region” on page 41.

This radio is restricted to use with a license and to use only in

certain EU countries or geographical areas of EU countries.

www.4Gon.co.uk [email protected] Tel: +44 (0)1245 808295 Fax: +44 (0)1245 808299

La pagina sta caricando ...

Ubiquiti airFiber 5X AF-5X Manuale utente

Marca: Ubiquiti

Modello: airFiber 5X AF-5X

Categoria: Networking

Tipo: Manuale utente

Questo manuale è adatto anche per

airFiber AF-5X

Scarica il pdf

rapporto

in altre lingue

English: Ubiquiti airFiber 5X AF-5X User manual

Ubiquiti airFiber 5X AF-5X Manuale utente

Questo manuale è adatto anche per

Ubiquiti airFiber 5X AF-5X Manuale utente

in altre lingue

Documenti correlati

Altri documenti