Ubiquiti airFiber AF-5XHD Quick Start Manuals

5 GHz Carrier Radio

with LTU Technology

Model: AF-5XHD

DATA

MGMT

GPS

LINK

DATA

MGMT

GPS

LINK

Introduction

Thank you for purchasing the Ubiquiti Networks® airFiber®

AF-5XHD. This Quick Start Guide is designed to guide you

through installation. Warranty terms, safety notices, and

compliance information are in the airFiberAF-5XHD User

Guide, available at: www.ubnt.com/download/airfiber

Package Contents

airFiber AF-5XHD GPS Antenna

Mount

External GPS

Antenna

Metal Strap Cable Ties

(Qty. 2)

Universal Bracket

5 GHz Carrier Radio

with LTU Technology

Model: AF-5XHD

DATA

MGMT

GPS

LINK

DATA

MGMT

GPS

LINK

Gigabit PoE (24V, 1A)

with Mounting Bracket

Power Cord Quick Start Guide

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Antenna Compatibility

The airFiber AF-5XHD radio is designed for use with the

following airFiber X antenna models:

• AF-5G23-S45

• AF-5G30-S45

• AF-5G34-S45

The AF-5XHD can also operate with the following RocketDish

™

antenna models:

• RD-5G30*

• RD-5G34*

* Requires Universal Bracket (included) or AF-5G-OMT-S45 Conversion

Kit (not included).

Installation Requirements

• Clear line of sight between airFiber radios

• Clear view of the sky for proper GPS operation

• Vertical mounting orientation

• Mounting point:

• At least 1 m below the highest point on the structure

• For tower installations, at least 3 m below the top of

thetower

• Ground wires – min. 10 AWG (5 mm

2

) and max. length:

1m. Asa safety precaution, ground the airFiber radio to

grounded masts, poles, towers, or grounding bars.

WARNING: Failure to properly ground your

airFiber radio will void your warranty.

• (Recommended) 2 Outdoor Gigabit PoE surge protectors

Note: For guidelines about grounding and lightning

protection, follow your local electrical regulatory

codes.

• Outdoor, shielded Category 6 (or above) cabling and

shielded RJ-45 connectors are required for all wired Ethernet

connections.

Hardware Overview

Port Cover

LED

Panel

Connects to

External GPS

Antenna

Chain 1: Connects to

- 45° on

airFiber Antenna

Chain 0: Connects to

+ 45° on

airFiber Antenna

Ports

Reset

Button

Management

Port

Data

Port

Management Port 10/100/1000 Mbps, secured Ethernet

port for configuration. In-Band Management is enabled by

default in the airFiber Configuration Interface. When In-Band

Management is disabled, the MGMT port is the only port that

can monitor, configure, and/or update firmware. This port can

also be used to provide redundant PoE power.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the device is

already poweredon.

Data Port Gigabit PoE port for handling all user traffic and

powering the device.

LEDs

Signal LEDs

Signal 4 LED will light blue when on.

Signal 3 LED will light green when on.

Signal 2 LED will light yellow when on.

Signal 1 LED will light red when on.

Bootup to airOS When powering on, the Power, GPS, LINK,

and Signal 1-4 LEDs light on. Once the CPU code takes over, the

GPS, LINK, and Signal 1-3 LEDs turn off. Signal 4 LED remains on

to indicate the boot sequence is underway.

Initializing airFiber Software When the airFiber application

begins to boot under airOS, the Signal 4 LED goes from solidly

on to a 2.5 Hz flash. This continues until the AF-5XHD is fully

booted.

Signal Level Once fully booted, the Signal 1-4 LEDs act as a

bar graph showing how close the AF-5XHD is to ideal aiming.

This is auto-scaled based on the link range, the antenna gains,

and the configured TX power of the remote AF-5XHD. Each

Signal LED has three possible states: On, Flashing, and Off. All

Signal LEDs would be solidly on in an ideal link. If the link has a

1 dB loss, the Signal4 LED will flash; a 2 dB loss and the Signal

4 LED will turn off. The full bar graph LED states are shown

below.

dB

loss

0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 -11 -12 -13

1 F 0 0 0 0 0 0 0 0 0 0 0 0

1 1 1 F 0 0 0 0 0 0 0 0 0 0

1 1 1 1 1 F F 0 0 0 0 0 0 0

1 1 1 1 1 1 1 1 1 1 F F F 0

0 = Off, 1 = On, F = Flashing

Additional LEDs

LED State Status

LINK

Off RF Off

Short Flash* Syncing

Normal Flash* Beaconing

Long Flash* Registering

On Operational

GPS

Off No GPS Synchronization

Normal Flash* Non-Operational (Weak Signal)

On Operational (Strong Signal)

MGMT

Off No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

DATA

Off No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

Off No Power

On Powered On

* Short Flash (1:3 on/off cycle)

Normal Flash (1:1 on/off cycle)

Long Flash (3:1 on/off cycle)

*640-00338-01*

640-00338-01

Installation Overview

We recommend that you configure your paired AF-5XHD

radios before site installation. The overview below summarizes

the installation procedure, and the subsequent sections

provide detailed installation information.

• Connect the airFiber PoE Adapter to the DATA port, and

connect your computer to the MGMTport.

• Configure the AF-5XHD.

• Install a ground wire and mount the AF-5XHD on an

airFiberX or RocketDish antenna.

• At the installation site, install the airFiber X or RocketDish

antenna with the mounted AF-5XHD radio (see the antenna’s

Quick Start Guide for installation instructions).

• Secure the ground wire and mount the GPS antenna.

• Establish and optimize the RF link.

Connecting Power over Ethernet

1. Lift the release latch on the bottom of the AF-5XHD and

slide the Port Cover off.

2. Connect an Ethernet cable to the DATA port.

3. Connect the Ethernet cable from the DATA port of the

AF-5XHD to the POE port of the adapter.

WARNING: Use only the included adapter, model

GP‑H240‑100G‑WH‑03. Failure to do so can damage

the unit and void the product warranty.

4. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a poweroutlet.

airFiber Configuration

The instructions in this section explain how to access the

airFiber Configuration Interface and configure the following

settings:

• Wireless Mode Configure one AF-5XHD as the AP and the

other as the CPE.

• Frequency Setting The operating Frequency must be the

same on both the AP and the CPE.

1. Connect an Ethernet cable from your computer to the

MGMT port on the AF-5XHD.

2. Configure the Ethernet adapter on your computer with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type http://192.168.1.20 in the

address field and press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Select your Country and Language.

You must agree to the Terms of Use to use the product.

Click Login.

Note: U.S. product versions are locked to the U.S.

Country Code to ensure compliance with FCC

regulations.

5. Click the Wireless tab.

6. Configure the Basic Wireless Settings:

a. For one AF-5XHD, select AP PTP as the Wireless Mode.

For the other AF-5XHD, select CPE PTP as the Wireless

Mode.

b. Enter a name in the SSID field. This should be the same

on both the AP and the CPE.

c. Select USA for the Country code to ensure compliance

with FCC regulations.

d. Change the Distance Scale to be larger than the

anticipated distance between the AP and CPE.

e. If needed, change the Channel Width, Frequency,

Output Power (EIRP), Antenna Gain, and Maximum TX

Modulation settings. The Channel Width and Frequency

should be the same on both the AP and the CPE.

7. Configure the Wireless Security:

a. Select WPA2‑AES for the Security mode.

b. Select PSK for the WPA Authentication mode.

c. In the WPA Preshared Key field, enter a combination of

alphanumeric characters (0-9, A-Z, or a-z).

Note: Currently only ASCII mode is supported.

8. Configure the Advanced wireless settings:

a. Enter the Duty Cycle on the AP.

b. Enter the Frame Length on both the AP and the CPE.

This should be the same on both the AP and the CPE.

9. Click Save Changes.

10. Configure each airFiber radio with a unique IP address for

the DATA port:

a. Click the Network tab.

b. For both the Data LAN Address and Management IP

Address options:

- DHCP Keep the default, DHCP, to use DHCP

reservation on your router to assign a unique

IPAddress.

- Static Change the IP Address, Netmask, and other

settings to make them compatible with your

network.

c. Enable the Ethernet Carrier Drop settings if needed.

d. Click Save Changes.

Repeat the instructions in the airFiber Configuration section on

the other AF-5XHD radio.

For details on the airFiber Configuration Interface, refer to the

airFiber AF-5XHD User Guide, available at:

www.ubnt.com/download/airfiber

Hardware Installation

Install a Ground Wire

1. Remove the nut from the Ground Bonding Point located on

the back of the AF-5XHD.

Ground

Bonding

Point

2. Attach a ground wire (min. 10 AWG or 5 mm

2

) to the lug

and replace the nut to secure the wire.

3. At the installation site, secure the other end of the ground

wire to a grounded mast, pole, tower, or grounding bar.

WARNING: Failure to properly ground your

airFiber radio will void your warranty.

Note: The ground wire should be as short as

possible and no longer than one meter in length.

Mount to an airFiber X Antenna

Follow the instructions in this section to mount the AF-5XHD

to an airFiber X antenna or to a RocketDish antenna equipped

with the AF-5G-OMT-S45 Conversion Kit.

Note: To mount the AF-5XHD to a RocketDish using the

included Universal Bracket, see the Mount to a RocketDish

Antenna section.

The airFiber X antenna AF-5G23-S45 is shown in this section:

1. Attach the airFiber X radio to the antenna by aligning the

four tabs on the back of the radio with the slots of the radio

mount. Then slide the radio down to lock it into place.

2. Attach the RF connectors to the radio in this combination:

+45° to Chain0 and -45° to Chain 1. Then slide the jackets

over the RF connectors to protect them.

3. Attach the external GPS antenna (included with the radio)

to the RF connector labeled GPS on the radio.

4. Attach the Protective Shroud by sliding it down over the

radio until it locks into the radio mount.

Mount to a RocketDish Antenna

Note: If you are mounting the AF-5XHD on a RocketDish

equipped with the AF-5G-OMT-S45 Conversion Kit, the

Universal Bracket is not needed. Refer instead to the

Mount to an airFiber X Antenna section for instructions.

The RocketDish RD-5G30 antenna is shown in this section:

1. Position the Universal Bracket over the back of the AF-5XHD

with the bracket clips over the AF-5XHD mounting tabs.

2. Push the bracket onto the AF-5XHD until it locks in place.

3. Attach the AF-5XHD to the RocketDish mounting bracket.

a. Align the mounting tabs on the Universal Bracket with

the RocketDish mounting bracket.

b. Slide the AF-5XHD down to lock it into place.

Mount the External GPS Antenna

Locate a mounting point that has a clear view to the sky, and is

above and as far away as possible from the AF-5XHD.

1. Attach the GPS Antenna Mount to the pole using the metal

strap, or attach it to a wall using the appropriate fasteners

(notincluded).

2. Place the External GPS Antenna on the mount.

3. Secure the cable of the External GPS Antenna to the mount

with a Cable Tie.

Connecting Power over Ethernet

1. Lift the release latch on the bottom of the AF-5XHD and

slide the Port Cover off.

2. Connect an outdoor, shielded Ethernet cable to the

DATAport.

3. Connect the Ethernet cable from the DATA port of the

AF-5XHD to the POE port of the adapter.

WARNING: Use only the included adapter, model

GP‑H240‑100G‑WH‑03. Failure to do so can damage

the unit and void the product warranty.

4. Connect an Ethernet cable from your LAN to the adapter’s

LAN port.

5. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mount the PoE Adapter (Optional)

1. Remove the Mounting Bracket from the adapter, place the

bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the Mounting

Bracket, and then slide the adapter down.

Surge Protection

For added protection, install two surge suppressors, such as

the Ubiquiti Ethernet Surge Protector, model ETH-SP, at the

end of each link. Install the first surge protector within one

meter of the airFiber DATA port, and install the second surge

protector at the ingress point of the location housing the

wired network equipment.

La pagina sta caricando ...

Ubiquiti airFiber AF-5XHD Quick Start Manuals

Ubiquiti airFiber AF-5XHD Quick Start Manuals

in altre lingue

Documenti correlati

Altri documenti