Hoover HIES55MCTT Manuale utente

Instruction Manual For Induction Hob

Manuale di istruzioni per piano cottura a induzione

MODEL: CIES55MCTT

Thank you for purchasing the Hoover induction hob. Please read this instruction

manual carefully before using the hob and keep it in a safe place for future reference.

ENGLISH

ITALIAN

EN-1

By placing the mark on this product, we are

confirming compliance to all relevant European

safety, health and environmental requirements

which are applicable in legislation for this

product.

Safety Warnings

Your safety is important to us. Please read this

information before using your cooktop.

Installation

Electrical Shock Hazard

• Disconnect the appliance from the mains

electricity supply before carrying out any work

or maintenance on it.

• Connection to a good earth wiring system is

essential and mandatory.

• Alterations to the domestic wiring system must

only be made by a qualified electrician.

• Failure to follow this advice may result in

electrical shock or death.

Cut Hazard

• Take care - panel edges are sharp.

• Failure to use caution could result in injury or

cuts.

Important safety instructions

• Read these instructions carefully before

installing or using this appliance.

• No combustible material or products should be

EN-2

placed on this appliance at any time.

• Please make this information available to the

person responsible for installing the appliance

as it could reduce your installation costs.

• In order to avoid a hazard, this appliance must

be installed according to these instructions for

installation.

• This appliance is to be properly installed and

earthed only by a suitably qualified person.

• This appliance should be connected to a circuit

which incorporates an isolating switch

providing full disconnection from the power

supply.

• Failure to install the appliance correctly could

invalidate any warranty or liability claims.

Operation and maintenance

Electrical Shock Hazard

• Do not cook on a broken or cracked cooktop. If

the cooktop surface should break or crack, switch

the appliance off immediately at the mains power

supply (wall switch) and contact a qualified

technician.

• Switch the cooktop off at the wall before

cleaning or maintenance.

• Failure to follow this advice may result in

electrical shock or death.

Health Hazard

EN-3

• This appliance complies with electromagnetic

safety standards.

• However, persons with cardiac pacemakers or

other electrical implants (such as insulin

pumps) must consult with their doctor or

implant manufacturer before using this

appliance to make sure that their implants will

not be affected by the electromagnetic field.

• Failure to follow this advice may result in death.

Hot Surface Hazard

• During use, accessible parts of this appliance

will become hot enough to cause burns.

• Do not let your body, clothing or any item other

than suitable cookware contact the Induction

glass until the surface is cool.

• Metallic objects such as knives, forks, spoons

and lids should not be placed on the hob surface

since they can get hot

• Keep children away.

• Handles of saucepans may be hot to touch.

Check saucepan handles do not overhang other

cooking zones that are on. Keep handles out of

reach of children.

• Failure to follow this advice could result in

burns and scalds.

Cut Hazard

• The razor-sharp blade of a cooktop scraper is

exposed when the safety cover is retracted. Use

with extreme care and always store safely and

out of reach of children.

• Failure to use caution could result in injury or

EN-4

cuts.

Important safety instructions

• Never leave the appliance unattended when in

use. Boilover causes smoking and greasy

spillovers that may ignite.

• Never use your appliance as a work or storage

surface.

• Never leave any objects or utensils on the

appliance.

• Do not place or leave any magnetisable objects

(e.g. credit cards, memory cards)or electronic

devices (e.g. computers, MP3 players) near the

appliance, as they may be affected by its

electromagnetic field.

• Never use your appliance for warming or

heating the room.

• After use, always turn off the cooking zones

and the cooktop as described in this manual (i.e.

by using the touch controls). Do not rely on the

pan detection feature to turn off the cooking

zones when you remove the pans.

• Do not allow children to play with the appliance

or sit, stand, or climb on it.

• Do not store items of interest to children in

cabinets above the appliance. Children climbing

on the cooktop could be seriously injured.

• Do not leave children alone or unattended in

the area where the appliance is in use.

• Children or persons with a disability which

EN-5

limits their ability to use the appliance should

have a responsible and competent person to

instruct them in its use. The instructor should be

satisfied that they can use the appliance without

danger to themselves or their surroundings.

• Do not repair or replace any part of the

appliance unless specifically recommended in the

manual. All other servicing should be done by a

qualified technician.

• Do not use a steam cleaner to clean your

cooktop.

• Do not place or drop heavy objects on your

cooktop.

• Do not stand on your cooktop.

• Do not use pans with jagged edges or drag pans

across the Induction glass surface as this can

scratch the glass.

• Do not use scourers or any other harsh

abrasive cleaning agents to clean your cooktop,

as these can scratch the Induction glass.

• If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid a

hazard.

•This appliance is intended to be used in

household and similar applications such as:

-staff kitchen areas in shops, offices and other

working environments; -farm houses; -by

clients in hotels, motels and other residential

type environments; -bed and breakfast type

environments.

EN-6

•WARNING: The appliance and its accessible

parts become hot during use.

Care should be taken to avoid touching heating

elements.

Children less than 8 years of age shall be kept

away unless continuously supervised.

•This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have

been given supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved.

•Children shall not play with the appliance.

Cleaning and user maintenance shall not be

made by children without supervision.

•WARNING: Unattended cooking on a hob with

fat or oil can be dangerous and may result in fire.

NEVER try to extinguish a fire with water, but

switch off the appliance and then cover flame e.g.

with a lid or a fire blanket.

•WARNING: Danger of fire: do not store items on

the cooking surfaces.

• Warning: If the surface is cracked, switch off

the appliance to avoid the possibility of electric

shock, for hob surfaces of glass-ceramic or

similar material which protect live parts

•A steam cleaner is not to be used.

EN-7

•The appliance is not intended to be operated by

means of an external timer or separate

remote-control system.

CAUTION: The cooking process has to be

supervised. A short term cooking process has to

be supervised continuously.

WARNING: In order to prevent tipping of the

appliance, this stabilizing means must be

installed. Refer to the instructions for

installation.

WARNING: Use only hob guards designed by the

manufactuer of the cooking appliance or

indicated by the manufacture of the appliance in

the instruction for use as suitable or hob guards

incorporated in the appliance. The use of

inappropriate guards can cause accidents.

This appliance incorporates an earth connection

for functional purposes only.

Congratulations on the purchase of your new Induction Hob.

We recommend that you spend some time to read this Instruction / Installation

Manual in order to fully understand how to install correctly and operate it.

For installation, please read the installation section.

Read all the safety instructions carefully before use and keep this Instruction /

Installation Manual for future reference.

EN-8

Product Overview

Top View

Control Panel

1.2000 W zone, boost to 2600W

2.1500 W zone, boost to 2000W

3.2000 W zone, boost to 2600W

4.1500 W zone, boost to 1800W

5. 2000 W zone, boost 2600W

6. Flex zone, 2800W boost 3500W

7. Glass plate

8. Control panel

1. Timer control

2. ON/OFF control

3. Power regulating key/booster function control

4. keylock control

5. Keep warm function

6.Pause function control

7. Flex zone

EN-9

A Word on Induction Cooking

Induction cooking is a safe, advanced, efficient, and economical cooking

technology. It works by electromagnetic vibrations generating heat directly in the

pan, rather than indirectly through heating the glass surface. The glass becomes

hot only because the pan eventually warms it up.

Before using your New Induction Hob

• Read this guide, taking special note of the ‘Safety Warnings’ section.

• Remove any protective film that may still be on your Induction hob.

Using the Touch Controls

• The controls respond to touch, so you don’t need to apply any pressure.

• Use the ball of your finger, not its tip.

• You will hear a beep each time a touch is registered.

• Make sure the controls are always clean, dry, and that there is no object (e.g. a

utensil or a cloth) covering them. Even a thin film of water may make the

controls difficult to operate.

iron pot

magnetic circuit

ceramic glass plate

induction coil

induced currents

EN-10

Choosing the right Cookware

• Only use cookware with a base suitable for induction

cooking. Look for the induction symbol on the

packaging or on the bottom of the pan.

• You can check whether your cookware is suitable by carrying out

a magnet test. Move a magnet towards the base of the pan. If it

is attracted, the pan is suitable for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

2. If does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or

copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is

the same size as the cooking zone. Use pans whose diameter is as large as the

graphic of the zone selected. Using a pot a slightly wider energy will be used at its

maximum efficiency. If you use smaller pot efficiency could be less than expected.

Always centre your pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

EN-11

Pan dimensions

The cooking zones are up to a limit, automatically adapted to the diameter of the

pan. However the bottom of this pan must have a minimum of diameter according

to the corresponding cooking zone. To obtain the best efficiency of your hob,

please place the pan in the centre of the cooking zone.

The base diameter of induction cookware

Cooking zone Minimum (mm)

1, 2 (180mm) 120

3，5 (210mm)

140

4 (160mm) 100

Flex zone 240 or 160*270

The above may vary according to the quality of the pan used.

Using your Induction Hob

To start cooking

1. Touch the ON/OFF control.

After power on, the buzzer beeps once, all displays

show “ – “ or “ – – “, indicating that the induction

hob has entered the state of standby mode.

2. Place a suitable pan on the cooking zone that

you wish to use.

• Make sure the bottom of the pan and the surface

of the cooking zone are clean and dry.

3.Set a power level by touching the slider, or slide along the “—”control, or just

touch any point of the “—”.

EN-12

Or

a. If you don’t set the power within 1 minute, the induction hob will

automatically switch off. You will need to start again at step 1.

b. You can modify the heat setting at any time during cooking.

c. If slide along the “—”, power will vary from stage 1 to stage 9.

If the display flashes alternately with the heat

setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centred on the cooking zone.

No heating takes place unless there is a suitable pan on the cooking zone.

The display will automatically turn off after 1 minutes if no suitable pan is placed

on it.

When you have finished cooking

1. Turn the cooking zone off by slide along the “—” to the left point, and then hold

for 1 second.

Make sure the power display shows “0”, then shows “H”.

and then

3. Turn the whole cooktop off by touching the ON/OFF control.

EN-13

4. Beware of hot surfaces

‘H’ will show which cooking zone is hot to touch. It will disappear when the

surface has cooled down to a safe temperature. It can also be used as an

energy saving function if you want to heat further pans, use the hotplate that

is still hot.

Using the Power Management

Using power management you can set the total power to 2.5kW/ 3.0kW/ 4.5kW/

6.5kW and 7.4kW. The default total power setting is the maximum power level.

Setting the total power level to fit your requirement

1. Make sure the cooktop is turned off.

Note: you can only set power management when the cooktop is turned off.

2. Touch the button “Pause” and hold for 5 seconds. You can hear the

buzzer beeps one time.

3. After you hear the beep, touch “+” and “-” button at the same time and hold for

3 second, the timer indicator will show flashing previous total power level, e.g.

‘2.5’. Touch and hold ” +” and ”-” for 1 second again to switch to other power level,

for example 3.0. When the power that you want is flashing, touch the button

“Pause” and hold for 5 seconds. The buzzer will beep 10 times. It means you have

finished the setting.

Note:

1. After step 2, you must touch the “+” and “-” within 3 seconds after you hear

the beep. Otherwise you will need to start again from step 2.

2. Once finish setting, wait till the end of 10 beeps. Do not touch any button during

this period. Otherwise the setting will be invalid.

EN-14

Power management Rules

If total power exceeds the limitation of 2.5kw, 3.0kw, 4.5kw, 6.5kw (depending

on which level you’ve set), you are not able to increase power stage of any zone.

If you increase it, the cooktop will beep 3 times and indicator will show a flashing

‘Pn’. Thus you need to decrease power stage of other zones before increasing the

power of objective zone.

Power Limitation in centre and right zones

• Cooking zones are divided into two groups. Each group has a maximum

electricity loading of 3600 W.

• Only Group b has this limitation. The limitation activates when the total

electricity loading of the cooking zones exceeds 3600 W.

• The limitation decreases the power to the other cooking zones.

• The heat setting display of the reduced zones changes between two levels.

e. g. if all zones are on, the biggest power level of three zones are decrease to

7-level, 7-level, 7-level.

In Group a both two zones can work at full power any time because they are

3500w in total.

In Group b if two zones are working and you switch on the third zone, the power

of third zone will be at largest 7 stage power and the other two zones will drop to

7 stage power automatically. Please turn off the other one or two zones if you want

the third zone to work at 9 stage power.

Using the Boost

Boost is the function that one zone rising to a larger power in one second and

EN-15

lasting for 5 minutes. Thus you can get a more powerful and faster cooking.

Using the Boost to get larger power

1. Touch the control panel button that you wish to boost, then hold the “b” for 3

second. The power display will show “P” to indicate that the zone is boosting.

2. The Boost power will last for 5 minutes and then the zone will go back to the “9”

power stage.

3. If you want to cancel the Boost during this 5 minutes, touch the “B” button for

twice. The heating zone will go back to “9” power stage. Or slide along the “—” to

the left point, the heating zone will go back to the power stage in which you

touched.

or

Restrictions when using

The five zones were divided into two groups. In one group, if use boost on one

zone, first make sure that the other zone is working on/below power level 5.

In Group b, if one zone is working at boost mode, at the same time there is only

one other zone can work.

EN-16

Using the Keep warm

Keep warm is the function that one zone keep a lower power to make the

temperature stable.

Using the Keep warm to get stable temperature

1. Touch the slider of the heating zone that you wish to keep warm, then touch the

keep warm button ,

the cooking zone indicator will display “A”.

2.If you want to cancel the keep warm, touch the slider of the heating zone, then

touch the button , the heating zone will go back to “0” power stage.

Using the Pause function

Pause function can be used at any time during cooking. It allows to stop the

induction cooktop and come back to it.

1. Make sure the cook zone is working.

2. Touch the button pause, the cooking zone indicator will show “ll”.

And then the operation of the induction cooktop will be deactivate within the scope

of all cooking zones, except the pause, on/off and lock keys.

3. To cancel the pause status, touch the pause button, then the cooking zone will

go back to the power stage which you set before.

EN-17

Flex Zone

• This area can be used as a single zone or as two different zones, accordingly to

the cooking needs anytime.

• Flexible area is made of two independent inductors that can be controlled

separately.

• Important: Make sure to place the cookwares centered on the single cooking

zone. In case of big pot, oval, rectangular and elongated pans make sure to place

the pans centered on the cooking zone covering both cross.

Examples for good and bad pot placements:

As big zone

1. Touch the slider of the heating zone (left side) that you wish to go into

flexizone, then touch the flex zone selection button to activate the flexible

area as a single big zone, the indicator next key will be on.

2. Touch the slide along the “—” control, or just touch any point of the “—” to

adjust the power level.

As two independent zones

1. If you want to cancel the flex zone, touch the slider of the heating zone again,

then touch the flex zone selection button, the indicator next to the flex zone

EN-18

button will disappear.

Locking the Controls

• You can lock the controls to prevent unintended use (for example children

accidentally turning the cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are

disabled.

To lock the controls

Touch the keylock control. The timer indicator will show “ Lo “.

To unlock the controls

1. Make sure the Induction hob is turned on.

2. Touch and hold the keylock control for a while

3. You can now start using your Induction hob.

When the hob is in the lock mode, all the controls are disable except the ON/OFF,

you can always turn the induction hob off with the ON/OFF control in an emergency,

but you shall unlock the hob first in the next operation.

Over-Temperature Protection

A temperature sensor equipped can monitor the temperature inside the Induction

hob. When an excessive temperature is monitored, the Induction hob will stop

operation automatically.

Over-spillage Protection

Over-spillage protection is a safety protection function. It switch off the hob

automatically within 10s if the water flow to the control panel, while buzzer will

beep 1 second.

Detection of Small Articles

When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other

small item (e.g. knife, fork, key) has been left on the hob, the hob automatically

go on to standby in 1 minute. The fan will keep cooking down the induction hob for

a further 1 minute.

Auto Shutdown Protection

Auto shut down is a safety protection function for your induction hob. It shut down

EN-19

automatically if ever you forget to turn off your cooking. The default working times

for various power levels are shown in the below table:

Power level

1

2

3

4

5

6

7

8

9

A

II

Default working timer

(hour)

8

4

2

When the pot is removed, the induction hob can stop heating immediately and the

hob automatically switch off after 2 minutes.

People with a heart pace maker should consult with their doctor before

using this unit.

Using the Timer

You can use the timer in two different ways:

• You can use it as a minute minder. In this case, the timer will not turn any

cooking zone off when the set time is up.

• You can set it to turn one cooking zone off after the set time is up.

• You can set the timer up to 99 minutes

Using the Timer as a Minute Minder

If you are not selecting any cooking zone

1. Make sure the cooktop is turned on.

Note: you can use the minute minder even if you’re not selecting any cooking

zone.

2. Touch “-’ or “+” of the timer control, the minder indicator will

start flashing and “30” will show in the timer display.

3. Set the time by touching the “-” or “+” control,

Hint: Touch the “-” or “+” control once to decrease or increase by 1 minute.

Hold the “-” or “+” control of the timer to decrease or increase by 10

minutes.

If the setting time exceeds 99 minutes, the timer will automatically return to 0

minute.

4. Cancel the time by touching the “-” of timer and scrolling down to “0”.

La pagina sta caricando ...

Hoover HIES55MCTT Manuale utente

Hoover HIES55MCTT Manuale utente

in altre lingue

Documenti correlati

Altri documenti