Wolf ICBDD30 Manuale utente

DOWNDRAFT VENTILATION

INSTALLATION INSTRUCTIONS

INSTRUCCIONES DE INSTALACIÓN

INSTRUCTIONS D’INSTALLATION

ISTRUZIONI PER L’INSTALLAZIONE

INSTALLATIONSANWEISUNGEN

ENGLISH 4

ESPÃNOL 18

FRANÇAIS 32

ITALIANO 46

DEUTSCH 60

3

As you follow these instruc tions, you will

notice WARNING and CAUTION symbols.

This blocked information is impor tant for the

safe and efficient installation of Wolf equip-

ment. There are two types of potential

hazards that may occur during installation.

Another footnote we would like to identify is

IMPORTANT NOTE: This highlights informa-

tion that is especially relevant to a problem-

free installation.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

®

is a registered trademark of Wolf Appliance, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

INSTALLATION REQUIREMENTS

IMPORTANT NOTE:

This installation must be

completed by a qualified installer or Wolf

authorized service center technician.

Installer:

Please read the entire Installation

Instructions prior to installation. Save these

instructions for the local inspector’s refer-

ence, then leave them with the homeowner.

Homeowner:

Please read and keep these

instructions for future reference and be sure

to read the entire Use & Care Information

prior to use.

Any questions or problems regarding the

installation should be directed to your dealer

or visit our website, wolfappliance.com.

IMPORTANT NOTE:

This appliance must be

installed in accordance with National Electrical

Codes, as well as all state, municipal and local

codes. The correct voltage, frequency and

amperage must be supplied to the appliance

from a dedicated, grounded circuit which is

protected by a properly sized circuit breaker or

time delay fuse. The proper voltage, frequency,

and amperage ratings are listed on the product

rating plate.

Record the model and serial numbers before

installing the downdraft ventilation system.

Both numbers are listed on the rating plate,

located above the airbox on the front side of

the unit. Refer to the illustration below.

BEFORE YOU START

Proper installation is the responsibility of

the installer.

Check with local utilities for electrical codes

that apply in your area. Local codes vary.

Installation, electrical connections and

grounding must comply with applicable

codes.

This appliance must be properly grounded.

Refer to Electrical Requirements on

page 7.

Make sure you have the tools and materials

necessary for proper installation.

Any required service must be performed by

a Wolf authorized service center. Wolf is not

responsible for service required to correct a

faulty installation.

WOLF DOWNDRAFT VENTILATION SYSTEMS

RATING PLATE

INFORMATION

Model Number

Serial Number

Rating plate location

Location of

rating plate

(behind filters)

5

OVERALL DIMENSIONS

MODELS ICBDD30I AND ICBDD30R

Overall Width 762 mm

Width of Chimney 667 mm

Overall Height

(above countertop)

230 mm

Overall Depth 60 mm

Depth of Chimney 38 mm

MODELS ICBDD36I AND ICBDD36R

Overall Width 914 mm

Width of Chimney 819 mm

Overall Height

(above countertop)

230 mm

Overall Depth 60 mm

Depth of Chimney 38 mm

6

WOLF DOWNDRAFT VENTILATION SYSTEMS

DOWNDRAFT VENTILATION

IMPORTANT NOTE:

Wolf downdraft ventila-

tion systems are recommended for use with

Wolf framed induction or electric, gas and

multi-function cooktops. They cannot be used

with unframed induction or electric cooktops

and are not recommended for use with the

electric grill, steamer and fryer modules.

A Pro ventilation hood is recommended for

use with Wolf dual fuel ranges, gas ranges

and rangetops.

IMPORTANT NOTE:

A downdraft can be

used with sealed burner rangetop Models

ICBSRT304 and ICBSRT366. An accessory trim

kit (810215) is necessary for this installation.

Contact your Wolf dealer for details.

Wolf downdraft ventilation systems are

available in 762 mm, 914 mm and 1156 mm

widths. The downdraft should be at least as

wide as the cooktop.

Models ICBDD30I, ICBDD36I and ICBDD45I

include an 850 m3/hr internal blower. Models

ICBDD30R, ICBDD36R and ICBDD45R are

shipped without a blower assembly and can

be used with a 1529 m3/hr remote blower

(812307), available through your Wolf dealer.

Models ICBDD30I and ICBDD30R

60 mm

762 mm

230 mm

667 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

914 mm

819 mm

60 mm

230 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

Models ICBDD36I and ICBDD36R

Model ICBDD30

Model ICBDD36

Model ICBDD45

Dimensions may vary to

+

–

3 mm.

7

INSTALLATION INSTRUCTIONS

Models ICBDD45I and ICBDD45R

1156 mm

1048 mm

60 mm

230 mm

38 mm

DEPTH OF

DOWNDRAFT CHIMNEY

ELECTRICAL REQUIREMENTS

Wolf downdraft ventilation systems require a

separate, 240 V 50/60 Hz power supply. The

service should have its own 10A circuit

breaker. The unit is supplied with a 2.5 m CEE

7/7 “Schuko” style Continental European

power cord. The specific location of the outlet

is not critical, as long as it is within reach of

the power cord that is located mid-way, top

and bottom, on the right side of the downdraft.

IMPORTANT NOTE:

If Model ICBDD30 is to be

installed in a 762 mm wide cabinet, Model

ICBDD36 in a 914 mm wide cabinet or Model

ICBDD45 in a 1156 mm wide cabinet, the

electrical outlet cannot be located on the back

wall of the cabinet. The outlet can be placed in

an adjacent cabinet within reach of the power

cord. An access hole for the power cord must

be drilled in the cabinet wall.

Choose the electrical location shown in

the illustration below that best suits your

installation.

Location of electrical

914 mm min

FOR MODEL ICBDD36

1156 mm min

FOR MODEL ICBDD45

762 mm min

FOR MODEL ICBDD30

OPTIONAL

ELECTRICAL

LOCATION IN

ADJACENT RIGHT

SIDE CABINET

E

OVERALL DIMENSIONS

MODELS ICBDD45I AND ICBDD45R

Overall Width 1156 mm

Width of Chimney 1048 mm

Overall Height

(above countertop)

230 mm

Overall Depth 60 mm

Depth of Chimney 38 mm

Dimensions may vary to

+

–

3 mm.

IMPORTANT

NOTE

You must follow

all National

Electrical Code

regulations. In

addition, be aware

of local codes and

ordinances when

installing your

service.

INSTALLATION SPECIFICATIONS

Wolf downdraft Model ICBDD30 will fit most

762 mm wide cabinets, Model ICBDD36 will fit

most 914 mm wide cabinets and Model

ICBDD45 will fit most 1156 mm wide cabinets.

It is recommended that oversized cabinets be

used for easier installation. Cabinet backs may

need to be removed.

Wolf downdraft ventilation systems can be

mounted in an island, peninsula or standard

wall location.

The illustration below provides installation

dimensions for all Wolf downdraft models.

Pay careful attention to the areas of potential

interference as noted in the illustration.

IMPORTANT NOTE:

To install a downdraft

system and a Wolf cooktop, you must allow for

a minimum 638 mm flat counter space from

front to back. A countertop with a raised lip or

backsplash may not allow enough space for

proper installation. 60 mm of flat countertop is

required behind the cooktop and 44 mm is

necessary between the back edge of the

cooktop and inside of cabinet back.

If downdraft Model ICBDD30 is installed in

combination with with two cooktops or inte-

grated modules, an integrated module support

(8603386) for downdraft ventilation is required.

The integrated module support is not required

for Model ICBDD45.

8

WOLF DOWNDRAFT VENTILATION SYSTEMS

54 mm

489 mm

COOKTOP CUT-OUT

DEPTH

914 mm

60 mm

638 mm

min

OF FLAT COUNTERTOP

*

8.7 mm

745 mm

COUNTERTOP

TO BOTTOM OF

AIR BOX

457

mm

92

mm

83 mm

127

mm

197 mm

16 mm

64 mm min

WITH NO

RAISED LIP

*

AREAS OF POTENTIAL INTERFERENCE

610 mm min

CABINET DEPTH

44 mm min

BACK EDGE

OF COOKTOP

TO INSIDE OF

CABINET BACK

*

181 mm

Downdraft installation dimensions

9

INSTALLATION INSTRUCTIONS

INSTALLATION SPECIFICATIONS

For installation of a downdraft system with a

cooktop, refer to the cooktop installation

instructions for the dimensions of the cooktop,

countertop cut-out and cabinet requirements.

The depth of the cooktop may vary and will

affect the location of the downdraft in the

countertop.

The illustration below provides countertop

cut-out dimensions for downdraft Models

ICBDD30, ICBDD36 and ICBDD45 installed with

a Wolf 762 mm or 914 mm cooktop or combi-

nation of cooktop and/or modules.

IMPORTANT NOTE:

For installation of a

downdraft with sealed burner rangetop

Models ICBSRT304 and ICBSRT366, an acces-

sory trim kit (810215) is necessary. Contact

your Wolf dealer for details. To obtain local

dealer information, visit our website, wolfap-

pliance.com.

The control module can be positioned horizon-

tally or vertically and located anywhere within

3 m of the downdraft assembly and a

minimum of 76 mm from edge of cooktop cut-

out. Refer to page 11 for instructions to install

the control module.

IMPORTANT NOTE:

The downdraft must be

used with a Wolf-approved control module and

top cover.

COUNTERTOP CUT-OUT

Layout and cut the cooktop cut-out far

enough forward so the downdraft will fit

behind it.

Set the cooktop in place and slide it as far

forward as possible. Center and square the

cooktop with edges of countertop.

Place the plastic template included with the

downdraft against the back flange of the

cooktop and centered. Trace around the

template to mark the downdraft opening.

Remove the cooktop from countertop.

Cut the downdraft opening. Be careful not

to chip the edges of the countertop.

686 mm

FOR MODEL ICBDD30

838 mm

FOR MODEL ICBDD36

1067 mm

FOR MODEL ICBDD45

64 mm min

76 mm

min FOR

CONTROL

MODULE

COOKTOP CUT-OUT

WIDTH

638 mm min

FLAT

COUNTERTOP

SPACE

489 mm

70 mm

COUNTERTOP TOP VIEW

Countertop cut-out dimensions

WOLF DOWNDRAFT VENTILATION SYSTEMS

leveling bracket – flange facing in

leveling bracket –

flange facing out

mounting screws

Downdraft mounting brackets

CONTROL MODULE

The remote-mounted control module and top

cover are included with the downdraft. Also

included are mounting brackets, RJ45 connec-

tor and mounting hardware.

The control module can be located anywhere

within reach of the 3 m power cable and a

minimum of 76 mm from edge of cooktop

cut-out. The remote-mounted control module

is 60 mm x 168 mm and can be positioned

horizontally or vertically in the countertop.

IMPORTANT NOTE:

Do not place the module

where it will be in the way of cooking, where

hot pans may be placed or where hot liquids

could be spilled on the controls.

To reduce the risk of burns or ignition of

clothing by reaching across burners,

control module must be mounted at least

76 mm from edge of cooktop cut-out.

DOWNDRAFT INSTALLATION

Set the downdraft into the opening. Extend

the leveling brackets to the floor of the

cabinet so the downdraft sits straight.

NOTE: The leveling brackets can be

removed and reattached in other positions.

The flange of the leveling bracket may have

to face inward in tight cabinet installations.

Refer to the illustration below.

Secure the downdraft to the countertop by

holding the downdraft against the back of

the countertop cut-out and tightening the

two mounting screws (one on each end of

unit) on the underside of the countertop.

Screw the leveling brackets to the bottom

of the cabinet. Tighten the screws holding

the leveling brackets to unit on each side.

10

INSTALLATION INSTRUCTIONS

CONTROL MODULE CONNECTION

Connect the RJ45 connector cable to the back

side of the remote-mounted control

module.

Connect the other end of the cable to the

electrical connection located on the right

side of downdraft assembly. Make sure that

all connections are tight.

Refer to the illustration placed on the front

of the downdraft for the correct orientation

of the RJ45 connector during installation

into the downdraft assembly.

CONTROL MODULE

You will be required to drill three holes and

connect the control module to the downdraft

assembly using the cable provided. A 25 mm

diameter hole for the RJ45 connector cable will

be centered horizontally and vertically in the

back side of the control module. Two 6 mm

diameter holes for the mounting screws will be

located 51 mm from the center of the RJ45

connector cable hole, one on each side.

CONTROL MODULE INSTALLATION

Mark the center of the control module on

the counter top. Measure 51 mm up (or left)

and 51 mm down (or right) to locate holes

for the mounting screws.

Carefully drill the three holes through the

countertop. Be careful not to damage or

chip the countertop surface while drilling.

Check the countertop thickness. Set the

control module in place and make sure the

threaded studs are long enough to allow

the nylon thumbnuts to fully engage.

Thicker countertops may require that the

holes be partially counter-sunk from below.

Apply a bead of caulk all the way around

the underside of the control module to

prevent liquids from reaching the electrical

connection or dripping through the holes in

the countertop. Position the control module.

From below the countertop, thread the two

nylon thumbnuts onto the studs of the

control module and hand tighten only.

11

WOLF DOWNDRAFT VENTILATION SYSTEMS

DUCTING CONSIDERATIONS

IMPORTANT NOTE:

Always consult a

qualified HVAC Engineer for specific ducting

applications.

Wolf downdraft models with an internal blower

are designed for use with 83 mm x 254 mm

ductwork and 83 mm x 356 mm ductwork for

models with a remote blower. Each can be

transitioned to 203 mm or 254 mm round

ductwork.

For best performance, 254 mm round ductwork

is recommended. The downdraft will operate

most efficiently when the ductwork does not

exceed 12 m in length.

Choose the ducting option that allows the

shortest length of ductwork and a minimum

number of elbows and transitions. Check the

location of floor joists, wall studs, electrical

wiring or plumbing for possible interference

with the ductwork. Refer to the illustrations

below for ducting options.

305 mm

MIN TO

GROUND

WALL CAP

INTERNAL BLOWER

INSTALLATION THROUGH WALL

Downdraft ducting options

305 mm

MIN TO

GROUND

INTERNAL BLOWER

INSTALLATION THROUGH WALL

305 mm

MIN TO

GROUND

254 mm

ROUND

REMOTE BLOWER

INSTALLATION THROUGH WALL

REMOTE

BLOWER

REMOTE BLOWER

ROOF MOUNT INSTALLATION

REMOTE

BLOWER

254 mm

ROUND

BLOWER OPTIONS

Wolf downdraft Models ICBDD30I, ICBDD36I

and ICBDD45I include an 850 m3/hr internal

blower. Models ICBDD30R, ICBDD36R and

ICBDD45R are shipped without a blower

assembly and can be used with a 1529 m3/hr

remote blower (812307), available through

your Wolf dealer.

IMPORTANT NOTE:

Blower options vary with

the cooking surface. For recommendations,

refer to the Wolf Design Guide found on the

Wolf website, wolfappliance.com.

IMPORTANT NOTE:

Install this downdraft

ventilation system only with a Wolf blower.

The blower will vary in size and is dictated by

the cooking surface, the volume of air that

needs to be moved and the length of the duct

run. A straight, short duct run with a limited

number of elbows and transitions will allow

the downdraft to perform most efficiently.

A remote-mounted blower will minimize the

amount of blower noise, but will not eliminate

the noise completely.

ACCESSORIES

Optional acces-

sories are available

through your

Wolf dealer. To

obtain local dealer

information, visit

our website,

wolfappliance.com.

12

INSTALLATION INSTRUCTIONS

IMPORTANT NOTE:

For installations where

the ductwork is riveted to the unit, an 83 mm x

254 mm collar is provided for models with an

internal blower and an 83 mm x 356 mm collar

is provided for models with a remote blower.

This will allow the blower to be removed and

replaced easily for service without disturbing

the ductwork.

IMPORTANT NOTE:

Use duct tape to seal the

connection between the blower outlet and

ductwork. Support the weight of the ductwork

as necessary to ensure sealed joints.

DUCTWORK INSTALLATION

IMPORTANT NOTE:

Wolf ventilation down-

draft systems must be vented to the outside.

IMPORTANT NOTE:

Before cutting the hole in

the cabinet for ductwork, check for interference

with floor joists, wall studs, electrical wiring or

plumbing.

Cut the hole in the cabinet as well as holes

in wall or floor as necessary for the

ductwork.

Mount the roof or wall cap and work back

towards the cabinet, attaching all ductwork,

elbows and transitions as previously

planned. Tape all ductwork connections to

make them secure and air tight.

Connect the ductwork and transition (if

required) to the downdraft. If necessary,

loosen the nuts and screws that hold the

blower in place, and slide the blower left or

right to align with the ductwork. Retighten

the screws and nuts.

To reduce the risk of fire, use only metal

ductwork.

13

WOLF DOWNDRAFT VENTILATION SYSTEMS

ADJUSTABLE DISCHARGE

Wolf downdraft systems have an adjustable

discharge that will allow you to negotiate

ducting around floor joists and other obstacles.

DISCHARGE CUT-OUT

DIMENSIONS:

260 mm x 89 mm

INTERNAL BLOWER

362 mm x 89 mm

IN-LINE OR

REMOTE BLOWER

CENTERLINE OF COUNTERTOP CUT-OUT

416 mm

INTERNAL BLOWER

546 mm

IN-LINE OR

REMOTE BLOWER

140 mm

INTERNAL BLOWER

108 mm

IN-LINE OR

REMOTE BLOWER

C

L

562 mm

INTERNAL BLOWER

483 mm

IN-LINE OR

REMOTE BLOWER

RIGHT

DISCHARGE

LOCATION

LEFT

DISCHARGE

LOCATION

CENTERLINE OF COUNTERTOP CUT-OUT

362 mm x 89 mm

IN-LINE OR

REMOTE BLOWER

CENTERLINE OF COUNTERTOP CUT-OUT

140 mm

INTERNAL BLOWER

108 mm

IN-LINE OR

REMOTE BLOWER

C

L

NOTE: Measurements are to centerline of duct cut-outs

ADJUSTMENT:

127 mm MAX

IN-LINE OR

REMOTE BLOWER

ADJUSTMENT:

25 mm – 178 mm

INTERNAL BLOWER

165 mm MAX

IN-LINE OR

REMOTE BLOWER

BOTTOM

DISCHARGE

LOCATION

Downdraft adjustable discharge

Three different discharge locations are avail-

able with side-to-side adjustment for accurate

alignment of ductwork. The blower is shipped

with the discharge facing down. Refer to the

illustration below for the discharge location

and adjustment that best suits your installa-

tion.

14

INSTALLATION INSTRUCTIONS

bottom

flange

clamp

channel

nuts

sheet metal

screw

blower

cover plate

clamp

channel

nut

sheet metal

screw

blower

motor plug

Down blower discharge adjustment Left or right blower discharge

ADJUSTING BLOWER DISCHARGE

DOWN DISCHARGE LEFT TO RIGHT

Adjusting the down discharge left to right will

keep the blower discharge in the down

position but allows some side-to-side adjust-

ment.

Follow these steps if the position of the blower

discharge needs to be moved left to right so

that ductwork does not interfere with floor

joists, plumbing or wiring below the unit. Refer

to the illustration below.

Place the downdraft assembly on its back

on a flat work surface.

Loosen the 4 nuts and 2 clamp channels.

Slide the blower to the desired position.

Use the supplied cover plate to close any

open space.

Tighten nuts to secure the top of blower

and use sheet metal screws through the

bottom flange to secure the bottom of the

blower.

DOWN TO LEFT OR RIGHT DISCHARGE

Substituting down discharge with left or right

discharge will switch the blower discharge

from the down position to the left or right of

downdraft assembly.

Follow these steps if it is necessary to rotate

the blower to the left or right discharge

location. Refer to the illustration below.

Place the downdraft assembly on its back

on a flat work surface.

Remove the 4 nuts and 2 clamp channels.

Remove the gear motor cover.

Carefully lift the blower and disconnect the

motor plug if necessary. Reposition the

blower and reconnect the motor plug.

Use the supplied cover plate to close any

open space.

Replace the clamp channels and use the

nuts to secure the blower in its new

position.

Reinstall the gear motor cover.

Use sheet metal screws (not supplied with

unit) through the bottom flange to secure

the bottom of the blower.

15

16

WOLF DOWNDRAFT VENTILATION SYSTEMS

INTERNAL BLOWER WIRING

ICBDD30I, ICBDD36I AND ICBDD45I

Mount a standard 220-240 V AC electrical

box, with 3-pronged grounded receptacle,

inside the cabinet or adjacent cabinet. Make

sure it is located within the reach of the

downdraft’s 2.5 m power cord.

Run the appropriate power cable into the

cabinet and connect it to electrical box and

outlet.

Plug the power cord of the downdraft into

the outlet.

brown to brown

blue to blue

green/yellow to

green/yellow

220-240 V AC

line in

Wiring connections

REMOTE BLOWER WIRING

ICBDD30R, ICBDD36R AND ICBDD45R

Mount a standard 220-240 V AC electrical

box, with 3-pronged grounded receptacle,

inside the cabinet or adjacent cabinet. Make

sure it is located within the reach of the

downdraft’s 2.5 m power cord.

Run the appropriate power cable into the

cabinet and connect it to electrical box and

outlet.

The remote blower may not exceed a 3.0

amp rating.

Run 2-wire plus ground power cable from

the remote blower to the electrical box on

the remote blower adapter plate.

Connect the downdraft wiring to the power

cable from the remote blower. Wire brown

to brown, blue to blue and green/yellow to

green/yellow. Refer to the illustration below.

Replace the electrical box cover.

Plug the power cord of the downdraft into

the outlet.

IMPORTANT NOTE:

For mounting and

installation of the remote blower, refer to the

installation instructions for your specific

blower.

17

TROUBLESHOOTING

IMPORTANT NOTE:

If the downdraft ventila-

tion system does not operate properly, follow

these troubleshooting steps:

Verify that power is being supplied to the

downdraft.

Check electrical connections to ensure that

the installation has been completed

correctly.

Refer to the Troubleshooting Guide in the

Wolf Downdraft Ventilation Use & Care

Information.

If the downdraft still does not work, contact

a Wolf authorized service center. Do not

attempt to repair the downdraft yourself.

Wolf is not responsible for service required

to correct a faulty installation.

IF YOU NEED SERVICE

Maintain the quality built into your down-

draft ventilation system by calling a Wolf

authorized service center.

For service in your area, contact your

Wolf dealer or visit our website,

wolfappliance.com

to find the regional

distributor by country.

When calling for service, you will need the

model and serial number of your down-

draft. This information is found on the

product rating plate, located above the

airbox on the front side of the unit. Refer to

the illustration on page 5.

The information and images in this book are the

copyright property of Wolf Appliance, Inc., an

affiliate of Sub-Zero, Inc. Neither this book nor any

information or images contained herein may be

copied or used in whole or in part without the

express written permission of Wolf Appliance, Inc.,

an affiliate of Sub-Zero, Inc.

CONTACT

INFORMATION

Website:

wolfappliance.com

INSTALLATION INSTRUCTIONS

Cuando consulte las instrucciones que aparecen

en esta guía, encontrará símbolos de ADVER-

TENCIA y PRECAUCIÓN. Esta información en

recuadros es importante para instalar el equipo

de Wolf de forma segura y eficaz. Existen dos

tipos de posibles riesgos que pueden producirse

durante una instalación.

Otro tipo de anotación que es importante

resaltar es la que se incluye en NOTA IMPOR-

TANTE: En esta nota se resalta la información

que resulta especialmente importante para que

la instalación se realice sin problemas.

indica una situación en la que se pueden

sufrir heridas leves o provocar daños secun-

darios al producto si no se siguen las

instrucciones.

indica peligro de que se produzcan heridas

personales graves o incluso puede provocar

la muerte si no se siguen las precauciones

especificadas.

WOLF

®

es una marca comercial registrada de Wolf Appliance, Inc.

INFORMACIÓN

DE CONTACTO

Página Web:

wolfappliance.com

REQUISITOS DE INSTALACIÓN

NOTA IMPORTANTE:

Esta instalación debe ser

realizada por un técnico cualificado o por un

técnico de mantenimiento autorizado de Wolf.

Instalador:

Lea las instrucciones de insta-

lación antes de llevar a cabo la instalación.

Guarde estas instrucciones para que el inspec-

tor local pueda utilizarlas como referencia y, a

continuación, entréguelas al propietario del

aparato.

Propietario:

Lea y guarde estas instrucciones

para que pueda utilizarlas como referencia en

el futuro y asegúrese de leer la guía de uso y

mantenimiento antes de utilizar el aparato.

Si tiene alguna pregunta o problema relacionado

con la instalación, debe ponerse en contacto con

su distribuidor o visite nuestra página Web

wolfappliance.com.

NOTA IMPORTANTE:

Este aparato debe insta-

larse siguiendo las normativas y reglamentos

nacionales vigentes sobre instalaciones eléctricas

así como todos los reglamentos estatales, munici-

pales y nacionales. Se debe aplicar al aparato el

voltaje, la frecuencia y el amperaje adecuados

desde una instalación eléctrica resistente con

toma de tierra protegida por un fusible de

retardo. El voltaje, la frecuencia y el amperaje se

muestran en la placa de datos del producto.

Apunte la referencia del modelo y los números de

serie antes de instalar la campana extractora de

encimera. Esta información se encuentra en la

placa de datos del producto que está situada en

la caja de aire de la parte delantera de la unidad.

Observe la siguiente ilustración.

ANTES DE COMENZAR

Llevar a cabo una instalación correcta es

responsabilidad del instalador.

Consulte la normativa eléctrica correspon-

diente a su área con los servicios públicos

locales. La normativa local puede variar. La

instalación, las conexiones eléctricas y la

conexión a tierra deben cumplir la normativa

aplicable.

Este aparato debe estar conectado a tierra de

manera correcta. Consulte la sección Requisi-

tos eléctricos en la página 21.

Compruebe que tiene las herramientas y los

materiales necesarios para realizar la insta-

lación de manera correcta.

Cualquier tarea de mantenimiento debe ser

realizada por un centro de asistencia técnica

autorizado de Wolf. Wolf no se hace respon-

sable de las tareas de mantenimiento que

deban realizarse para corregir una instalación

defectuosa.

CAMPANAS EXTRACTORAS DE ENCIMERA DE WOLF

INFORMACIÓN

DE LA PLACA

DE DATOS

Referencia del

modelo

Número de serie

Ubicación de la placa de datos

Ubicación de la placa

de datos (detrás de los filtros)

19

MEDIDAS GENERALES

MODELOS ICBDD30I E ICBDD30R

Anchura total 762 mm

Anchura de chimenea 667 mm

Altura total

(sobre encimera)

230 mm

Profundidad total 60 mm

Profundidad de chimenea 38 mm

MODELOS ICBDD36I E ICBDD36R

Anchura total 914 mm

Anchura de chimenea 819 mm

Altura total

(sobre encimera)

230 mm

Profundidad total 60 mm

Profundidad de chimenea 38 mm

CAMPANAS

EXTRACTORAS DE ENCIMERA DE WOLF

CAMPANA

EXTRACTORA DE

ENCIMERA

NOTA IMPORTANTE:

Se recomienda utilizar las

campanas extractoras de encimera de Wolf con

placas de inducción, vitrocerámicas, placas de

gas y placas multifunción con marco. Estas

campanas no se puede utilizar con vitrocerámicas

o placas de inducción sin marco y no se

recomienda utilizar esta campana extractora con

los módulos de freidora, vaporizador ni con el

módulo de parrilla eléctrico. Para las cocinas

mixtas, las cocinas de gas y las encimeras de

cocción a gas se recomienda utilizar una

campana extractora Pro.

NOTA IMPORTANTE:

Con la encimera de

cocción con quemadores herméticos modelo

ICBSRT304 e ICBSRT366 se puede utilizar una

campana extractora de encimera. Es necesario

utilizar un kit de marco para campana (810215)

para realizar esta instalación. Póngase en

contacto con su distribuidor de Wolf para

obtener más detalles.

Las campanas extractoras de encimera de Wolf

están disponibles en anchos de 762 mm, 914 mm

y 1.156 mm. La campana extractora debe tener al

menos la misma anchura que la placa.

Los modelos ICBDD30I, ICBDD36I e ICBDD45I

incluyen un ventilador interno de 850 m3/hr. Los

modelos ICBDD30R, ICBDD36R e ICBDD45R se

envían sin ventilador y se pueden utilizar con

un ventilador remoto de 1.529 m3/hr (812307)

disponible a través de su distribuidor de Wolf.

Modelos ICBDD30I e ICBDD30R

60 mm

762 mm

230 mm

667 mm

38 mm

PROFUNDIDAD DE

CHIMENEA DE CAMPANA

914 mm

819 mm

60 mm

230 mm

38 mm

PROFUNDIDAD DE

CHIMENEA DE CAMPANA

Modelos ICBDD36I e ICBDD36R

Modelo ICBDD30

Modelo ICBDD36

Modelo ICBDD45

Las medidas pueden variar

+

–

3 mm.

20

La pagina sta caricando ...

Wolf ICBDD30 Manuale utente

Wolf ICBDD30 Manuale utente

in altre lingue

Documenti correlati

Altri documenti