Ubiquiti PowerBeam PBE-5AC-500-ISO Guida Rapida

Marca: Ubiquiti

Modello: PowerBeam PBE-5AC-500-ISO

Categoria: Antenne di rete

Tipo: Guida Rapida

5 GHz airMAX

ac Bridge with

500 mm RF Isolated Reflector

Model: PBE-5AC-500-ISO

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam®acISO. This Quick Start Guide is designed to

guide you through installation and includes warranty terms.

Package Contents

Reflector Radome Antenna Feed Rear Housing

Mounting

Bracket

Adjustment

Bracket

Hex Bolts with Washers

(Qty. 4)

Pole Clamp

(Qty. 2)

Carriage Bolts

(Qty. 4)

Flange Nuts

(Qty. 4)

Screws with Washers

(Qty. 4)

Washers

(Qty. 4)

5 GHz airMAX

ac Bridge with

500 mm RF Isolated Reflector

Model: PBE-5AC-500-ISO

Nylon Insert

Lock Nuts

(Qty. 4)

Gigabit PoE

(24V, 0.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Antenna Feed

Ethernet Port

Release Button Slot

Mounting Bracket

Release Button

Reflector

Alignment Pins

Reset Button

Radome

Technology

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the device is

poweredon. Alternatively, the device may be reset remotely

via a Reset button located on the bottom of the Gigabit

PoE adapter.

Release Button After you assemble the device, check the

Release button; it should be fully engaged in the Release Button

Slot of the Rear Housing. This ensures that the Antenna Feed is

locked into place. If you need to remove the Antenna Feed, you

must depress the Release button first.

LEDs

Power The Power LED will light blue when the

device is connected to a power source.

Ethernet The Ethernet LED will light steady blue

when an active Ethernet connection is made and

flash when there is activity.

Signal In airOS®, you can modify the threshold

value for the wireless signal strength LEDs on the

Wireless tab under Signal LED Thresholds. Each LED

will light when the wireless signal strength is equal

to or greater than the LED’s threshold value. The

default threshold values for these LEDs are shown

below:

-65 dBm

-73 dBm

-80 dBm -94 dBm

Application Examples

The PowerBeam mounted outdoors with the Reflector

installed provides directional outdoor coverage (gain is

reflector‑dependent).

The PowerBeam mounted outdoors without the Reflector

installed provides outdoor‑to‑indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

1. Align and insert the tabs of the Mounting Bracket into

the slots of the Reflector. Rotate the Mounting Bracket

counterclockwise until the alignment holes in the dish and

bracket align with each other.

2. For added support in high‑wind environments, insert four

Screws with Washers into the holes in the Reflector and

Mounting Bracket, and secure each screw with a Washer

and a Nylon Insert Lock Nut.

Mounting Bracket

Reflector

3. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Mounting Bracket. Push the Rear

Housing into the Mounting Bracket.

4. View the Reflector from the front. Ensure that the three

hooks (indicated below) of the Rear Housing are fully

engaged with the inner wall of the Reflector and locked

into place.

IMPORTANT: Before proceeding, lightly pull the Rear

Housing to confirm that it is locked into place.

5. Push in the sides of the Cable Door and detach it from the

Rear Housing.

6. Attach the Antenna Feed.

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release Button is fully engaged.

Release

Button

Bottom View

7. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed. Then re‑attach the Cable Door to the

RearHousing.

8. Attach the Pole Clamps to the Adjustment Bracket.

a. Hold the Adjustment Bracket with its clamps facing you

and the Elevation Indicators towards the top.

b. Insert the Carriage Bolts through the holes of the

Adjustment Bracket.

c. Place the Pole Clamps on the bolts on one side of the

bracket by sliding the hole of the clamp over the bolt.

d. Place one Flange Nut on each bolt.

Elevation

Indicator

9. Mount the Adjustment Bracket on the pole and secure it.

a. Place the Adjustment Bracket against the pole.

b. Slide the slot of each Pole Clamp over the adjacent

Carriage Bolt.

c. Tighten the Flange Nuts of the bolts to 25 N · m to secure

the Adjustment Bracket to the pole.

25 N · m

Note: The mounting assembly can accommodate a

Ø 40 ‑ 80 mm pole.

10. Insert the Pivot Pins on the inside of the Adjustment Bracket

into the Mounting Bracket Slots.

Pivot Pin

(one on each side of

Adjustment Bracket)

Mounting

Bracket Slot

11. Secure the Adjustment Bracket to the Mounting Bracket

using the four Hex Bolts with Washers.

12. Align the Notch on the Reflector with the Arrow at the top

of the Radome. Guide the Radome’s side and top tabs over

the Reflector rim and slide the Radome down onto the

Reflector.

Arrow

Notch

Radome

Side Tab

Reflector

Rim

Radome

Side Tab

Radome

Top Tab

*640-00219-06*

640-00219-06

13. Snap the bottom three tabs of the Radome over the

Reflector rim.

Bottom

Tabs

14. Adjust the elevation angle.

a. Loosen the four Hex Bolts on both sides of the antenna.

b. Pivot the antenna until the Elevation Indicator shows

the desired elevation angle.

c. Tighten the four Hex Bolts.

Elevation

Indicator

Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to

Connecting to the PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet

cable from the device’s Main Ethernet port to a

PoE‑enabled Ethernet port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the device’s Ethernet port

to the POE port of the Gigabit PoE adapter.

2. Connect an Ethernet cable from your LAN to the adapter’s

LAN port.

3. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre‑drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Accessing airOS

Verify connectivity in the airOS Configuration Interface.

1. Make sure that your host system is connected via Ethernet

to the device.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser and type https://192.168.1.20

in the address field. Press enter (PC) or return (Mac).

https://192.168.1.20

4. Enter ubnt in the Username and Password fields. Select

your Country and Language. You must agree to the Terms of

Use to use the product. Click Login.

500 ISO

Note: The Country setting for U.S. product versions

is restricted to a choice of Canada, Puerto Rico, or the

U.S. to ensure compliance with FCC/IC regulations.

The airOS Configuration Interface will appear, allowing you

to customize your settings as needed. For additional details

on the airOS Configuration Interface, refer to the User Guide

available at www.ubnt.com/download/airmax

You can also manage your device using the Ubiquiti Network

Management System. Setup using the UNMS

™

app requires

the U‑Installer, sold separately.

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer’s responsibility to make sure the device is

operated within local country regulatory requirements.

Since Ubiquiti Networks equipment can be paired with a

variety of antennas and cables, the Antenna and Output Power

fields are provided to the professional installer to assist in

meeting regulatory requirements.

Specifications

PBE‑5AC‑500‑ISO

Dimensions (with Radome) 564 x 564 x 308 mm

(22.20 x 22.20 x 12.13")

Weight (Mount Included) 5.2 kg

(11.5 lb)

Gain 27 dBi

Networking Interface (1) 10/100/1000 Ethernet Port

Enclosure Outdoor UV Stabilized Plastic

Max. Power Consumption 8W

Power Supply 24V, 0.5A Gigabit PoE Adapter (Included)

Power Method Passive PoE (Pairs 4, 5+; 7, 8 Return)

Wind Survivability 200 km/h

(125 mph)

Wind Loading 984 N @ 200 km/h

(221.2 lbf @ 125 mph)

Certications CE, FCC, IC

Mounting Pole Mounting Kit Included

Operating Temperature ‑40 to 70° C (‑40 to 158° F)

Operating Humidity 5 to 95% Noncondensing

Shock and Vibrations ETSI300‑019‑1.4

Operating Frequency (MHz)

Worldwide 5150 ‑ 5875

USA

U-NII-1 U‑NII‑2A U‑NII‑2C U‑NII‑3

5150 ‑ 5250 5250 ‑ 5350 5470 ‑ 5725 5725 ‑ 5850

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in a location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2‑wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short‑circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty

La pagina sta caricando ...

Ubiquiti PowerBeam PBE-5AC-500-ISO Guida Rapida

Marca: Ubiquiti

Modello: PowerBeam PBE-5AC-500-ISO

Categoria: Antenne di rete

Tipo: Guida Rapida

Scarica il pdf

rapporto

in altre lingue

English: Ubiquiti PowerBeam PBE-5AC-500-ISO Quick start guide
română: Ubiquiti PowerBeam PBE-5AC-500-ISO Ghid de inițiere rapidă

Ubiquiti PowerBeam PBE-5AC-500-ISO Guida Rapida

Ubiquiti PowerBeam PBE-5AC-500-ISO Guida Rapida

in altre lingue

Documenti correlati

Altri documenti