Ubiquiti PrismStation AC Guida Rapida

Shielded airMAX

®

ac Radio

with airPrism

®

Technology and

Dedicated Wi-Fi Management

Model: PS-5AC

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Introduction

Thank you for purchasing the Ubiquiti Networks®

PrismStation

™

AC. This Quick Start Guide is designed to guide

you through installation and also includes warrantyterms.

Package Contents

PrismStation AC GPS Antenna Mounting

Bracket

Pole Clamp

Carriage Bolts

(Qty. 2)

Flange Nuts

(Qty. 2)

Allen Wrench

Shielded airMAX

®

ac Radio

with airPrism

®

Technology and

Dedicated Wi-Fi Management

Model: PS-5AC

Gigabit PoE (24V, 1A)

with Mounting Bracket

Power Cord Quick Start Guide

TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet

cable and earth grounding must be used as conditions of product warranty. TOUGHCable

™

is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Installation Requirements

• The PS-5AC must be used with one of the following

horns (not included):

• Prism®AP-5-30

• PrismAP-5-45

• PrismAP-5-60

• PrismAP-5-90

• The GPS Antenna needs to have clear line of sight to thesky

for proper GPS operation.

• 13 mm wrench

• 5 mm hex socket (recommended for the Mounting Bracket)

• Shielded Category 5 (or above) cabling with drain wire

should be used for all wired Ethernet connections and

should be grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit

www.ubnt.com/toughcable

• Surge protection should be used for all outdoor installations.

We recommend that you use two Ethernet Surge Protectors,

model ETH-SP, one near the PrismStation and the other

at the entry point to the building. The ETH-SP will absorb

power surges and safely discharge them into the ground.

To LAN

ETH-SP

ES-8-150W

PS-5AC*

* Shown with the PrismAP-5-45

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Hardware Overview

Reset

Button

Ethernet

Port

Power

LED

GPS Antenna

Connector

GPS Antenna Connector This is used to connect the included

GPS Antenna.

Power LED The LED will light blue when the device is

connected to a power source.

Ethernet Port This Gigabit Ethernet port is used to connect

the power and should be connected to the LAN and DHCP

server.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PrismStation

is poweredon. Alternatively, the PrismStation may be reset

remotely via a Reset button located on the bottom of the

Gigabit PoE Adapter.

Release Button To remove the attached horn, rotate the horn

counterclockwise while depressing the Release Button.

Release

Button

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Hardware Installation

These instructions show the PrismAP-5-45; however, the

PrismStation is also compatible with the following horns:

• PrismAP-5-30

• PrismAP-5-60

• PrismAP-5-90

1. To install the horn, insert the PrismAP into the PrismStation

and align the arrow on the horn with the Release Button.

2. Press down on the horn and rotate it clockwise until you

hear a click.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Pole-Mounting

1. Attach the Pole Clamp to the Mounting Bracket.

a. Hold the Mounting Bracket with its clamps facing you

and the head of the Tightening Bolt facing upward.

b. Insert the two Carriage Bolts through the holes of the

Mounting Bracket.

c. Slide the hole of the Pole Clamp over one bolt of the

Mounting Bracket.

d. Place one Flange Nut on each bolt.

2. Loosen the Tightening Bolt of the Mounting Bracket and

open the bracket 90°.

Tightening Bolt

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

3. Mount the PrismStation on the pole and secure it.

a. Place the Mounting Bracket against the pole.

b. Slide the slot of the Pole Clamp over the adjacent

Carriage Bolt.

c. Tighten the Flange Nuts of the bolts to 25 N ∙ m to

secure the Mounting Bracket to the pole.

25 N ∙ m

4. Insert the PrismStation into the Mounting Bracket, and then

tighten the bolt to lock the PrismStation in place.

Note: The mounting assembly can accommodate a

Ø 25 - 75 mm pole.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

5. Adjust the elevation angle.

a. Loosen the Elevation Screw on the bottom of the

bracket.

Elevation Screw

b. Pivot the PrismStation until the Elevation Indicator

shows the desired elevation angle.

Elevation Indicator

c. Tighten the Elevation Screw to 15 N ∙ m.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Connecting to Power and GPS

1. Remove the port cover by lifting up the latch of the cover

and sliding the cover out.

2. Remove the rubber gasket from the port cover.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

3. Connect an Ethernet cable to the Ethernet port.

4. Connect the GPS Antenna to the GPS Antenna Connector.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

5. Punch out the cutout for the GPS cable.

6. Replace the port cover.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

7. Fit the rubber gasket over the Ethernet cable, and then

slide the gasket into the port cover.

8. Place the magnetic GPS Antenna on a steel surface near the

PrismStation.

Note: Ensure that the GPS Antenna has clear line of

sight to the sky for proper GPS reception.

9. Connect the power using one of the following options:

• Using the included Gigabit PoE Adapter: Go to

Connecting to the PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet

cable from the PrismStation’s Ethernet port to a

PoE-enabled Ethernet port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the PrismStation to the

POE port on the PoEAdapter.

2. Connect an Ethernet cable from your LAN to the LAN port

on the PoE Adapter.

3. Connect the Power Cord to the PoE Adapter, and then plug

the Power Cord into a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

*640-00330-03*

640-00330-03

Accessing airOS via Wi-Fi

Verify connectivity in the airOS® Configuration Interface.

There are two methods, the UNMS

™

and Web Portal. Both

are available for 15 minutes immediately after you power

on the PrismStation. If necessary, you can power cycle the

PrismStation to re-enable its Wi-Fi.

Proceed to the appropriate instructions:

UNMS App

1. Download the UNMS app from the AppStore (iOS) or

Google Play

™

(Android).

2. Connect your device’s Wi-Fi to the PrismStation SSID

named: PS-5AC:<MAC Address>

Note: Ensure that DHCP is enabled on your

Wi-Fiadapter.

3. Launch the app.

4. Tap the PrismStation on the Connections screen.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

5. Tap Connect on the Login screen.

6. Select your Country and tap Done.

7. Customize your settings as needed.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Web Portal

1. Connect your device’s Wi-Fi to the PrismStation SSID

named: PS-5AC:<MAC Address>

Note: Ensure that your Wi-Fi connection has DHCP

enabled.

2. Launch your web browser and go to:

http://setup.ubnt.com

3. Enter ubnt in the Username and Password fields. Select

your Country and Language. You must agree to the Terms of

Use to use the product. Click Login.

Note: The Country setting for U.S. product versions is

restricted to a choice of Canada, Puerto Rico, or the

U.S. to ensure compliance with FCC/IC regulations.

The airOS Configuration Interface will appear, allowing you

to customize your settings as needed. For additional details

on the airOS Configuration Interface, refer to the User Guide

available at www.ubnt.com/download/airmax

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Installer Compliance Responsibility

Devices must be professionally installed and it is the

professional installer's responsibility to make sure the device is

operated within local country regulatory requirements.

The Antenna and Output Power fields are provided to

the professional installer to assist in meeting regulatory

requirements.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Specifications

PS-5AC

Dimensions

Mounting Hardware Only

155 x 155 x 104 mm

(5.16 x 5.16 x 4.09")

83 x 117 x 69 mm

(3.27 x 4.61 x 2.72")

Weight

Mounting Hardware Only

0.77 kg (1.70 lb)

0.79 kg (1.74 lb)

Networking Interface (1) 10/100/1000 Ethernet Port

RF Connector (1) GPS

LED Power

Max. Power Consumption 10W

Power Supply 24V, 1A Gigabit PoE Adapter (Included)

Power Method 24V Passive PoE (Pairs 4, 5+; 7, 8 Return)

Supported Voltage Range 20 to 26VDC

Wind Loading 31 N @ 200 km/h (7 lbf @ 125 mph)

Wind Survivability 200 km/h (125 mph)

Operating Temperature -40 to 70° C (-40 to 158° F)

Operating Humidity 5 to 95% Noncondensing

Mounting Pole-Mount (Kit Included)

ESD/EMP Protection ± 24kV Contact/Air

Certications CE, FCC, IC

Operating Frequency (MHz)

Worldwide 5150 - 5875

USA

U-NII-1:

5150 - 5250

U-NII-2A:

5250 - 5350

U-NII-2C:

5470 - 5725

U-NII-3:

5725 - 5850

Management Radio (MHz)

Worldwide 2412 - 2472

USA 2412 - 2462

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Safety Notices

1. Read, follow, and keep these instructions.

2. Heed all warnings.

3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in a location that can

be submerged by water.

WARNING: Avoid using this product during an electrical

storm. There may be a remote risk of electric shock from

lightning.

Electrical Safety Information

1. Compliance is required with respect to voltage, frequency, and current

requirements indicated on the manufacturer’s label. Connection to a

different power source than those specified may result in improper

operation, damage to the equipment or pose a fire hazard if the

limitations are not followed.

2. There are no operator serviceable parts inside this equipment. Service

should be provided only by a qualified service technician.

3. This equipment is provided with a detachable power cord which has

an integral safety ground wire intended for connection to a grounded

safety outlet.

a. Do not substitute the power cord with one that is not the provided

approved type. Never use an adapter plug to connect to a 2-wire

outlet as this will defeat the continuity of the grounding wire.

b. The equipment requires the use of the ground wire as a part of the

safety certification, modification or misuse can provide a shock

hazard that can result in serious injury or death.

c. Contact a qualified electrician or the manufacturer if there

are questions about the installation prior to connecting the

equipment.

d. Protective earthing is provided by Listed AC adapter. Building

installation shall provide appropriate short-circuit backup

protection.

e. Protective bonding must be installed in accordance with local

national wiring rules and regulations.

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

Limited Warranty

UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the

product(s) furnished hereunder (the “Product(s)”) shall be free from defects

in material and workmanship for a period of one (1) year from the date

of shipment by UBIQUITI NETWORKS under normal use and operation.

UBIQUITI NETWORKS’ sole and exclusive obligation and liability under

the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,

to repair or replace any Product that fails to conform to the above

warranty during the above warranty period. The expense of removal and

reinstallation of any Product is not included in this warranty. The warranty

period of any repaired or replaced Product shall not extend beyond its

original term.

Warranty Conditions

The above warranty does not apply if the Product:

(I) has been modified and/or altered, or an addition made thereto,

except by Ubiquiti Networks, or Ubiquiti Networks’ authorized

representatives, or as approved by Ubiquiti Networks in writing;

(II) has been painted, rebranded or physically modified in any way;

(III) has been damaged due to errors or defects in cabling;

(IV) has been subjected to misuse, abuse, negligence, abnormal

physical, electromagnetic or electrical stress, including lightning

strikes, or accident;

(V) has been damaged or impaired as a result of using third party

firmware;

(VI) has no original Ubiquiti MAC label, or is missing any other original

Ubiquiti label(s); or

(VII) has not been received by Ubiquiti within 30 days of issuance of

the RMA.

In addition, the above warranty shall apply only if: the product has been

properly installed and used at all times in accordance, and in all material

respects, with the applicable Product documentation; all Ethernet cabling

runs use CAT5 (or above), and for outdoor installations, shielded Ethernet

cabling is used, and for indoor installations, indoor cabling requirements

are followed.

Returns

No Products will be accepted for replacement or repair without obtaining

a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS

during the warranty period, and the Products being received at UBIQUITI

NETWORKS’ facility freight prepaid in accordance with the RMA process of

UBIQUITI NETWORKS. Products returned without an RMA number will not

be processed and will be returned freight collect or subject to disposal.

Information on the RMA process and obtaining an RMA number can be

found at: www.ubnt.com/support/warranty

Available from A1 Security Cameras

www.a1securitycameras.com email: [email protected]

La pagina sta caricando ...

Ubiquiti PrismStation AC Guida Rapida

Ubiquiti PrismStation AC Guida Rapida

in altre lingue

Documenti correlati

Altri documenti