Danfoss ORT-10 Guida d'installazione

RET B + RF

Electronic dial setting thermostat with LCD display

User & Installation Instructions

®

Certification Mark

2

Installation Instructions 3-9

User Instructions 10-14

Instructions d’installation 15-20

Instructions d’utilisateur 21-23

Installationsanweisungen 24-29

Inbetriebnahme-Instruktion 30-32

Instrucciones de instalación 33-38

Instrucciones del usuario 39-41

Instruktions vejledning 42-47

Brugervejleding 48-50

Installatie handleiding 51-56

Instructiesevoor Gebruik 57-59

Ïäçãßåò åãêáôÜóôáóçò 60-65

Ïäçãßåò ÷ñÞóçò 66-68

Instrukcja instalacji 69-74

Instrukcja Użytkownika 75-77

Montavimo instrukcijos 78-83

Informacija Vartotojui 84-86

Istruzioni per l’uso 87-92

Istruzioni per l’utente 93-95

GB

F

D

ES

DK

NL

G

P

LT

I

3

Installation Instructions

Important note RF products: Ensure that there are no large metal objects, such as boiler

cases or other large appliances, in line of sight between the transmitter and receiver as

these will prevent communication between thermostat and receiver.

Installation Instructions

GB

Features

RET B (RF) / RET B-LS (RF) / RET B-NSB

(RF)

Contact rating 10 - 230 Vac, 3 (1) (excl. North America)

Contact rating

(N.America)

10 - 24 Vac, 50/60Hz, 3(1)A

Temperature Accuracy ±1°C

Contact Type SPDT Type 1B

Transmitter frequency 433.92 MHz (RF models)

Transmitter range 30m max (RF models)

Power Supply 2 x AA/MN1500 alkaline batteries

Control Pollution

Situation

Degree 2

Rated Impulse Voltage 2.5 kV

Designed to meet BS EN 60730-2-9 (EN 300220 for RF)

Ball Pressure Test 75°C

Temperature Range 5-30°C

4

Mounting

Fix at a height of 1.5m

approx from the oor,

away from draughts or

heat sources such as

radiators, open res or

direct sunlight.

Installation Instructions

GB

5

Wiring (not RF models)

RET-B (3050 12/01)

3

7

Installation Instructions

GB

6

DIL switch settings

Heating selection

Slide the DIL switches to the settings

required (see below)

Cooling selection

COOL

ON/OFF

6 CYCLES

°F

COOL

NO DELAY

4 MIN DELAY

°F

HEAT

CHRONO

3 CYCLES

°C

HEAT

2 MIN DELAY

°C

ON/OFF - boiler switches ON

when below set temperature

and OFF when above

CHRONO -

energy saving

feature which res the boiler

at regular intervals to maintain

a set temperature, achieving a

constant ambient environment

for the user.

l use 6 Cycles for radiator

systems

l use 3 Cycles for

underoor heating

COMPRESSOR

DELAY

Installation Instructions

GB

7

Receiver Wiring (RF only)

RX1 & 2 (3055 12/01)

COM

RX3 (3056 12/01)

RX1 & RX2 RX3

Note: 1) For mains voltage operated systems, link terminal 2 to mains live supply

2) Power supply to unit must not be switched by timeswitch

Locking & Limiting

Installation Instructions

GB

8

Commissioning (RF only)

If the thermostat and the receiver have been supplied

together in a combined pack, the units have been paired in

the factory and no commissioning is required (RX1 only).

Step 1 RET B-RF

Position the setting dial to number

1. Remove dial, press & hold LEARN

button for 3 seconds (located under

setting dial).

Do not replace the setting dial yet

NOTE: Thermostat now transmits

signal continuously for 5 mins.

Step 2 RX1

Press and hold buttons PROG and CH1 until green light

ashes.

LEARN

Installation Instructions

GB

9

Step 3 RX2/RX3

For RX2 or RX3 repeat steps 1 and 2 for each thermostat and

channel, leaving at least 5 mins between the commissioning

of each thermostat.

Step 4 RET B-RF

To replace the thermostat setting dial, position the dial to

number 1.

Installation Instructions

GB

10

What is a room thermostat?

... an explanation for householders

A room thermostat simply switches the heating system on and o

as necessary. It works by sensing the air temperature, switching on

the heating when the air temperature falls below the thermostat

setting, and switching it o once this set temperature has been

reached.

Turning a room thermostat to a higher setting will not make the

room heat up any faster. How quickly the room heats up depends

on the design of the heating system, for example, the size of boiler

and radiators.

Neither does the setting aect how quickly the room cools down.

Turning a room thermostat to a lower setting will result in the room

User Instructions

GB

11

being controlled at a lower temperature, and saves energy.

The heating system will not work if a timeswitch or programmer has

switched it o.

The way to set and use your room thermostat is to nd the lowest

temperature setting that you are comfortable with, and then leave it

alone to do its job. The best way to do this is to set the room thermo-

stat to a low temperature – say 18°C – and then turn it up by one de-

gree each day until you are comfortable with the temperature. You

won’t have to adjust the thermostat further. Any adjustment above

this setting will waste energy and cost you more money.

If your heating system is a boiler with radiators, there will usually be

only one room thermostat to control the whole house. But you can

have dierent temperatures in individual rooms by installing ther-

mostatic radiator valves (TRVs) on individual radiators. If you don’t

have TRVs, you should choose a temperature that is reasonable for

the whole house. If you do have TRVs, you can choose a slightly

higher setting to make sure that even the coldest room is comfort-

able, then prevent any overheating in other rooms by adjusting the

TRVs.

Room thermostats need a free ow of air to sense the temperature,

so they must not be covered by curtains or blocked by furniture.

Nearby electric res, televisions, wall or table lamps may prevent

User Instructions

GB

12

User Instructions

Display

The LCD displays actual room temperature until the setting dial

is moved.

Setting the temperature

Turn setting dial to required temperature. The selected

temperature will ash in the LCD to signify it is showing set

temperature.

After a short period the display stops ashing and shows actual

room temperature.

Thermostat status (heat mode only)

A ame symbol will be lit whenever the thermostat is calling

for heat.

User Instructions

GB

13

Thermostat status (cool mode only)

A snowake symbol will be lit whenever the thermostat is

calling for cooling. If this is seen to ash, the thermostat output

is delayed for a short period to prevent compressor damage.

Low battery indication

A battery symbol will ash in the display when batteries require

replacement. Batteries should be replaced within 15 days, after

which the thermostat will turn o the load it is controlling. When

this happens “Of” will be displayed.

IMPORTANT: alkaline batteries must be used.

User Instructions

GB

14

RET B-LS model only

This model is tted with an Auto/O switch.

When the switch is set in “I” position the thermostat

controls at the temperature set by the setting dial.

When set to “O” the thermostat output is turned o and

“Of” is displayed.

RET B-NSB model only

This model is tted with a Day/Night switch.

When the switch is set to the “Sun Symbol”, the thermostat

controls at the temperature set by the setting dial.

When set to the “Moon symbol”, the thermostat controls

at 4°C below the temperature set by the setting dial.

NOTE: if used to control cooling, thermostat controls 4°C higher, with

switch in MOON position.

User Instructions

GB

15

Instructions d’installation

Remarque importante pour version sans l (RF):Veiller à ce qu’aucun gros objet métal-

lique (caisson de chaudière ou autres gros appareils domestiques) ne fasse obstacle aux

communications entre le thermostat et le récepteur.

Instructions d’installation

F

Caractéristiques

RET B (RF), RET B-LS (RF)

& RET B-NSB (RF)

Caractéristique de contact 10 - 230 Vca, 3 (1) A

Précision de la température ±1°C

Type de contact SPDT Type 1B (inverseur)

Fréquence de fonctionnement 433.92 MHz (RF)

Portée émetteur 30m max (RF)

Alimentation 2 piles alcalines x AA / MN1500

Niveau de recyclage Degré 2

Tension de choc nominale 2.5 kV

Normes de fabrication BS EN 60730-2-9

Essai à la bille 75°C

Plage de témperatures 5-30°C

Dimensions (mm) 85 larg x 86 haut x 42 épaiss

16

Montage

Fixez l’appareil à une

hauteur d’environ 1,5

m du sol, à l’écart des

courants d’air ou des

sources de chaleur telles

que radiateurs, ammes

nues ou lumière directe du

soleil.

Instructions d’installation

F

17

Câblage (versions câblées seulement)

RET-B (3050 12/01)

3

7

Instructions d’installation

F

18

Réglages d’installateur

Chauage

Faites glisser les microcontacts dans

les positions requises (voir ci-dessous).

Froid

COOL

ON/OFF

6 CYCLES

°F

COOL

NO DELAY

4 MIN DELAY

°F

HEAT

CHRONO

3 CYCLES

°C

HEAT

2 MIN DELAY

°C

ON/OFF (Marche/Arrêt) – la

chaudière se met en marche

lorsque la température est

inférieure à la température

dénie et s’arrête lorsque la

température est supérieure.

Chrono-proportionnel

l fonction d’économie

d’énergie qui déclenche

la chaudière à intervalles

réguliers pour maintenir une

température dénie, orant

un environnement ambiant

constant à l’utilisateur.

l Utilisez 6 cycles pour les

systèmes de radiateur.

l Utilisez 3 cycles pour le

chauage sous plancher.

COMPRESSOR

DELAY

Instructions d’installation

F

19

Câblage du Récepteur RX (modèles RF uniquement)

RX1 & 2 (3055 12/01)

COM

RX3 (3056 12/01)

RX1 & RX2 RX3

Verrouillage & Limitation

NB. Pour les systèmes alimentés sur secteur, reliez la borne 2 à la phase du secteur.

Instructions d’installation

F

20

Instructions

Si le thermostat émetteur et le récepteur ont été fournis

ensemble dans un kit, ces deux éléments peuvent

communiquer directement sans manipulation particulière

(Modèles RX1 uniquement).

Etape 1 RET B-RF - Régler la molette

sur position 1. Pressez la touche LEARN

pendant 3 secondes (situé sous le cadran

de réglage). Ne pas replacer le cadran de

réglage pour l’instant.

Remarque : Le thermostat transmet

maintenant en continu pendant 5 minutes.

Etape 2 RX1 - Appuyez sur les touches PROG et CH1 en les

maintenant enfoncées pendant 3 secondes jusqu’à ce que le

voyant vert clignote une fois.

Etape 3 RX2/RX3 - Pour RX2 ou RX3, répétez les points 1 et 2

pour chaque thermostat et canal, en laissant au moins 5 min entre

la mise en service de chaque thermostat.

Etape 4 RET B-RF - Replacer la molette en l’ayant réglée sur 1.

LEARN

(modèles RF uniquement)

Instructions d’installation

F

La pagina sta caricando ...

Danfoss ORT-10 Guida d'installazione

Danfoss ORT-10 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti