Garmin Fusion, MS-BB300OEM Guida d'installazione

Marca: Garmin

Modello: Fusion, MS-BB300OEM

Tipo: Guida d'installazione

FUSION

MS-BB300 Installation

Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in

personal injury, damage to the vessel, or poor product

performance.

See the Important Safety and Product Information guide in the

product box for product warnings and other important

information.

This device must be installed according to these instructions.

Disconnect the vessel's power supply before beginning to install

this product.

Before applying power to this product, make sure it has been

correctly grounded, following the instructions in the guide.

CAUTION

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation,

contact FUSION Product Support.

Software Updates

For best results, you should update the software in all FUSION

devices at the time of installation to ensure compatibility.

Go to www.fusionentertainment.com/marine to download the

latest software. Software updates and instructions are available

on your device product page.

Mounting Considerations

CAUTION

In high ambient temperatures and after extended use, the

device enclosure may reach temperatures deemed dangerous

to touch. Therefore the unit must be installed in a location where

it will not be touched during operation.

NOTICE

This device should be mounted in a location that is not exposed

to extreme temperatures or conditions. The temperature range

for this device is listed in the product specifications. Extended

exposure to temperatures exceeding the specified temperature

range, in storage or operating conditions, may cause device

failure. Extreme-temperature-induced damage and related

consequences are not covered by the warranty.

• The device must be mounted in a location where it is not

submerged.

• The device must be mounted in a location with adequate

ventilation where it is not exposed to extreme temperatures.

• The device should be mounted so that the cables can be

connected easily.

• To achieve IPX3 water ingress protection and optimal heat

sink cooling, the device must be mounted on a vertical

surface with the connectors pointing downward.

• The device can be mounted on a horizontal surface, but such

positioning might not achieve IPX3 water ingress protection.

• To avoid interference with a magnetic compass, the device

should be installed at least 203 mm (8 in.) away from a

compass.

Mounting the FUSION BB300 Device

NOTICE

If you are mounting the device in fiberglass, when drilling the

pilot holes, it is recommended to use a countersink bit to drill a

clearance counterbore through only the top gel-coat layer. This

will help to avoid cracking in the gel-coat layer when the screws

are tightened.

NOTE: Stainless-steel screws may bind when screwed into

fiberglass and overtightened. It is recommended to apply an

anti-seize lubricant to the screws before installing them.

NOTE: Screws are included with the device, but they may not

be suitable for the mounting surface.

Before you mount the device, you must select a mounting

location and determine what screws and other mounting

hardware are needed for the surface.

Place the device in the mounting location and mark the

location of the pilot holes.

Drill a pilot hole for one corner of the device.

Loosely fasten the device to the mounting surface with one

corner and examine the other three pilot-hole marks.

Mark new pilot-hole locations if necessary, and remove the

device from the mounting surface.

Drill the remaining pilot holes.

Secure the device to the mounting location.

Connection Considerations

The device must be connected to power, either the boat ignition

or an external switch, a NMEA 2000

network, speakers, and

media input sources to function correctly. You should carefully

plan the layout of the device, the NMEA 2000 network, the

speakers, and your input sources before making any

connections.

Connector Identification

Connector Connects to

ANT External AM/FM antenna

AUX IN 1 Stereo line-level RCA auxiliary source

AUX IN 2 Stereo line-level RCA auxiliary source

ZONE 3 Separate amplifier and speakers

SUB OUT Mono line-level subwoofer (tied to ZONE 3)

for amplifier

WIRED REMOTE NMEA

2000

FUSION NRX or NMEA 2000 network

SXM TUNER SiriusXM

tuner

USB USB-compatible media device

Power and speakers

Reserved for future use

Wire Identification

Wire Function Wire Color Notes

Power (+) Yellow This should be connected to a

constant 12 Vdc source capable of

supplying 15 A.

Ground (-) Black

February 2017 Printed in Thailand 190-01914-02_0B

Wire Function Wire Color Notes

Ignition Red This should be connected to a

separate switched 12 Vdc

connection, such as an ignition

bus, to turn the device on and off.

If you are not using a switched

12 Vdc connection, you must

connect this to the same source

as the yellow (power) wire.

Amplifier on Blue/white This is connected only when using

an external amplifier on ZONE 3

and on SUB OUT (optional).

Mute Brown/white When connected to ground, this

mutes the audio or switches the

input to AUX2. This is available in

the settings menu.

Speaker zone 1 left

(+)

White

Speaker zone 1 left

(-)

White/black

Speaker zone 1 right

(+)

Gray

Speaker zone 1 right

(-)

Gray/black

Speaker zone 2 left

(+)

Green

Speaker zone 2 left

(-)

Green/black

Speaker zone 2 right

(+)

Purple

Speaker zone 2 right

(-)

Purple/black

Connecting to Power

When connecting the stereo to power, you must connect both

power wires. The yellow power wire should be connected

directly to the battery, or connected using a 15 A isolator switch.

This provides power to the stereo and a constant trickle-power

standby feed. The red signal wire should be connected to the

same battery through the ignition or another manual switch to

turn the stereo on and off.

If you are not routing the red wire to the ignition or another

manual switch, you can connect the yellow to the red, and

connect them to the positive (+) battery terminal. You should put

a fuse on the red wire.

If it is necessary to extend the yellow power and black ground

wires, use 14 AWG (2.08 mm

) wire. For extensions longer than

1 m (3 ft.), use 12 AWG (3.31 mm²) wire.

If it is necessary to extend the red signal wire, use 22 AWG

(0.33 mm

) wire.

Route the yellow power

and black ground

wires to the

battery and route the wiring-harness plug to the stereo.

Do not connect the wiring harness to the stereo until all of the

bare wire connections have been made.

Connect the black wire to the negative (-) battery terminal.

Select an option:

• Connect the yellow wire to the positive (+) battery

terminal, and route the red signal wire

to the ignition or

another manual switch

• Connect the yellow wire to the red, and connect them to

the positive (+) battery terminal.

NMEA 2000 Connection Considerations

NOTICE

If you purchased the stereo and remote as a bundle (FUSION

MS-BB300R), do not use the included adapter cable

(CAB000862) to connect the FUSION BB300 stereo to an

existing NMEA 2000 network. Existing networks are normally

powered separately. You must obtain a non-powered drop cable

(CAB000863) from FUSION to connect to existing NMEA 2000

networks.

The FUSION MS-BB300 stereo can connect to an existing

NMEA 2000 network or to a FUSION NRX remote control.

Through the NMEA 2000 network, you control the FUSION MS-

BB300 device using a compatible chartplotter or FUSION NRX

remote control.

The FUSION MS-BB300R stereo and remote bundle package

includes the cables needed to connect the FUSION BB300

stereo to a stand-alone FUSION remote control network. If you

need to connect the FUSION MS-BB300R stereo and remote

bundle to an existing NMEA 2000 network, you must obtain a

non-powered drop cable (CAB000863) from FUSION.

The FUSION MS-BB300 stereo package includes a NMEA 2000

drop cable to connect the FUSION BB300 stereo to an existing

NMEA 2000 network. A standard NMEA 2000 drop cable is not

compatible with the connector on the device, although the

included cable can be extended to a maximum length of 2 m

(6 ft.) using a standard NMEA 2000 cable.

Item Description

FUSION BB300 device

Compatible chartplotter

FUSION NRX remote control

12 Vdc power source with an ignition or in-line switch

FUSION BB300 NMEA 2000 drop cable

This can be extended to a maximum length of 2 m (6 ft.) using a

standard NMEA 2000 cable.

NMEA 2000 drop cable

FUSION NRX remote control drop cable.

This can be extended to a maximum length of 2 m (6 ft.) using a

standard NMEA 2000 cable.

NMEA 2000 power cable

NMEA 2000 terminator or backbone cable

NMEA 2000 T-connector

Subwoofer Connection Considerations

This device supports output to a powered subwoofer from ZONE

3 (optional).

2 FUSION MS-BB300 Installation Instructions

The subwoofer port on the device outputs a mono line-level

signal from both RCA connectors. The port output audio level is

linked to ZONE 3.

• If your subwoofer amplifier has two RCA input connectors,

you should connect both connectors to the device.

• If your subwoofer amplifier has one RCA input connector, you

can connect it to either subwoofer output RCA connector on

the device, because the two RCA subwoofer outputs are

parallel.

• Because the subwoofer output is linked to the ZONE 3

output, you must connect the blue wire from the wiring

harness to the subwoofer amplifier to provide a signal to turn

it on.

Speaker Amplifier Connection Considerations

In addition to the two stereo speaker zones available through

the wiring harness, this stereo can be connected to a separate

amplifier and speakers through the ZONE 3 connection

(optional).

• The blue wire from the wiring harness must be connected to

the amplifier to provide a signal to turn on the amplifier with

the stereo. If it is necessary to extend this blue signal wire,

use 22 AWG (0.33 mm

) wire.

• The audio output is a stereo line-level output over standard

RCA cable.

Installing the USB and 3.5 mm Socket

The USB and 3.5 mm socket is provided only with the FUSION

MS-BB300R stereo and remote bundle. You may purchase the

USB and 3.5 mm socket as an accessory (MS-CBUSB3.5).

Before installing the socket, make sure the cables will reach the

mounting location and the ports on the back of the device. If

needed, the RCA cables can be extended using a standard

stereo RCA extension cable.

To allow for a proper seal, the mounting surface should be no

thicker than 15 mm (

in.).

Remove the nut

from the socket and separate it from the

connected cable by pulling through one connector

at a

time.

Do not remove the protective cover

from the socket.

Mark the mounting location of the socket and drill a 30 mm

in.) hole through the mounting surface.

From the front of the mounting surface, feed the cables

through the hole by inserting one connector at a time, and

pull the cables through until the socket rests in the hole.

To ensure proper orientation, the USB socket

should be on

the top.

Place the nut over both the USB and 3.5 mm audio cables,

thread it along the cables to the USB and 3.5 mm socket, and

fasten the socket to the surface.

If necessary, route the USB cable to the stereo and connect it

to the USB port.

If necessary, route the 3.5 mm connector cable to the stereo

and connect it to the AUX IN 1 or AUX IN 2 port.

Stereo Information

Specifications

General

Dimensions (L × W × H) 99.6 × 235 × 66 mm (3.94 × 9.25 × 2.63 in.)

Weight 0.88 kg (1.96 lb.)

Water resistance IPX3: Protected against spraying water when

tilted up to 60 degrees vertically.

Operating temperature From 0 to 50°C (from 32 to 122°F)

Storage temperature From -20 to 70°C (from -4 to 158°F)

Input voltage 10.8 to 16 Vdc negative ground

Fuse rating 15 A

NMEA 2000 LEN 1 (50 mA)

Compass-safe distance 203 mm (8 in.)

Audio Amplifier

Output music power per channel 50 W

Total output music power 200 W

Speaker impedance 4 Ohm per channel

Total harmonic distortion (1 W output, 4 ohm load,

from 20 Hz to 20 kHz)

0.04 typical

< 0.1% max.

Pre-output voltage 3 V peak

Current (standby with ignition off) < 3 mA

Current (max.) 15 A

Current (muted) < 800 mA

Inputs and Outputs

AUX IN 1 and

AUX IN 2

RCA stereo line input for sources such as CD, DVD,

and MP3 player

ZONE 3 RCA stereo line output

SUB OUT RCA dual mono line output (ZONE 3)

ANT Motorola connector (standard AM/FM antenna

connector)

USB USB-A industry standard

Compatible with USB flash drives audio playback with

supported audio formats and MTP devices

USB works with iPod touch

(2nd through 5th

generation), iPod classic

, iPod nano

(4th through 7th

generation), iPhone

5, iPhone 4s, iPhone 4, iPhone

3Gs, iPhone 3G

Tuner Europe and

Australasia

USA Japan

FM radio

frequency range

87.5 to 108 MHz 87.5 to

107.9 MHz

76 to 95 MHz

FM frequency

step

50 kHz 200 kHz 50 kHz

AM radio

frequency range

522 to 1620 kHz 530 to

1710 kHz

522 to

1620 kHz

AM frequency

step

9 kHz 10 kHz 9 kHz

Registering Your FUSION MS-BB300

Help us better support you by completing our online registration

today.

• Go to www.fusionentertainment.com.

• Keep the original sales receipt, or a photocopy, in a safe

place.

Getting the Owner's Manual

You can get the latest owner's manual and translations of

manuals from the web.

Go to www.fusionentertainment.com/marine.

Select your product.

Select Manuals & Downloads.

FUSION MS-BB300 Installation Instructions 3

Select a manual.

Garmin®, the Garmin logo, and the FUSION® logo are trademarks of Garmin Ltd. or its

subsidiaries, registered in the USA and other countries. Fusion and FUSION-Link™ are

trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used

without the express permission of Garmin.

Apple®, the Apple logo, iPod®, iPod touch®, iPod classic®, iPod nano®, and iPhone®

are trademarks of Apple Inc., registered in the U.S. and other countries. Android™ is a

trademark of Google Inc.

Bluetooth® word mark and logos are owned by the Bluetooth

SIG, Inc. and any use of such marks by Garmin is under license. NMEA®, NMEA

2000®, and the NMEA 2000 logo are registered trademarks of the National Marine

Electronics Association. Sirius, XM and all related marks and logos are trademarks of

their respective owners.

Made for iPhone 5, iPhone 4s, iPhone 4, iPhone 3GS, iPhone 3G, iPod touch (2nd

through 5th generation), iPod classic, and iPod nano (4th through 7th generation).

"Made for iPod and iPhone" means that an electronic accessory has been designed to

connect specifically to an iPod or an iPhone respectively, and has been certified by the

developer to meet Apple performance standards. Apple is not responsible for the

operation of this device or its compliance with safety and regulatory standards. Please

note that the use of this accessory with an iPhone may affect wireless performance.

www.fusionentertainment.com

TA-2013/2178

Garmin Fusion, MS-BB300OEM Guida d'installazione

Marca: Garmin

Modello: Fusion, MS-BB300OEM

Tipo: Guida d'installazione

Scarica il pdf

rapporto

in altre lingue

English: Garmin Fusion, MS-BB300OEM Installation guide

Garmin Fusion, MS-BB300OEM Guida d'installazione

Garmin Fusion, MS-BB300OEM Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti