Yamaha RX-V385 Manuale utente

RX-V385
Yamaha
Marca
Yamaha
Modello
RX-V385
Categoria
Lettori di cassette
Tipo
Manuale utente
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Natural Sound Stereo Receiver
Ampli-syntoniseur stéréo de la série “Natural Sound”
Natural Sound Stereoreceiver
Natural Sound Stereoreceiver
Ricevitore stereo a suono naturale
Receptor estéreo de Sonido Natural
Natural Sound Stereo Ontvanger
RX-485 RDS/385 /385 RDS
This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or
87/308/EEC.
Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE.
Diese Geräte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.
Dette apparat overholder det gaeldende EF-direktiv vedrørende radiostøj.
Questo apparecchio è conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi.
Este producto está de acuerdo con los requisitos sobre interferencias de radio frecuencia fijados por el Consejo Directivo
87/308 CEE.
Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.
2
●
Indoor FM Antenna
●
Antenne FM intérieure
●
UKW-Innenantenne
●
FM inomhusantenn
●
Antenna FM per interni
●
Antena FM interior
●
FM Binnenantenne
●
Remote Control Transmitter
●
Emetteur de télécommande
●
Fernbedienungsgeber
●
Fjärrkontrollsändare
●
Telecomando
●
Transmisor del control remoto
●
Afstandbediening
SUPPLIED ACCESSORIES
●
After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS
●
Après le déballage, vérifier que les pièces suivantes sont incluses.
MITGELIEFERTE ZUBEHÖRTEILE
●
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
MEDFÖLJANDE TILLBEHÖR
●
Kontrollera effer det apparaten packats upp att följande delar finns med.
ACCESSORI IN DOTAZIONE
●
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
ACCESORIOS INCLUIDOS
●
Desembale el aparato y verifique que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES
●
Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
●
AM Loop Antenna
●
Antenne AM à boucle
●
MW-Rahmenantenne
●
AM ramantenn
●
Antenna AM ad anello
●
Antena de cuadro de AM
●
AM Lusantenne
●
Batteries (size AA, R6, UM-3)
●
Piles (taille AA, R6, UM-3)
●
Batterien (größ AA, R6, UM-3)
●
Batterier (storlek AA, R6, UM-3)
●
Batterie (dimensioni AA, R6, UM-3)
●
Pilas (tamaño AA, R6, UM-3)
●
Batterijen (maat AA, R6, UM-3)
RX-485 RDS
RX-385, RX-385 RDS
Supplied Accessories ......................................2
Caution ............................................................4
Connections ....................................................5
Operations .......................................................9
Tuning Operations .........................................12
Preset tuning .................................................13
Receiving RDS Stations
RX-485 RDS and RX-385 RDS only ..........16
Remote Control Transmitter ..........................21
Notes about the Remote Control
Transmitter ....................................................22
Troubleshooting .............................................23
Specifications ................................................24
Thank you for selecting this YAMAHA stereo receiver.
3
English
How to Use This Manual
This manual describes three YAMAHA receivers, RX-385, RX-385 RDS and RX-485 RDS. There are some differences between
those three models. Especially, RX-385 RDS and RX-485 RDS contain the functions for receiving special data on RDS network
stations.
RX-385, on the other hand, is a receiver with a usual FM/AM tuning function.
Several places in the manual refer to differences in features between the three models. Be sure to follow the procedure for the
model you are using.
* RDS is a data transmitting service system in network which is employed by FM stations. RDS stations are increasing in many
countries (especially in Europe).
FEATURES
CONTENTS
●
RX-485 RDS
65W
+
65W (8Ω) RMS Output Power,
0.04% THD, 20
–
20,000 Hz
RX-385 and RX-385 RDS
40W
+
40W (8Ω) RMS Output Power,
0.04% THD, 20
–
20,000 Hz
●
High Dynamic Power, Low Impedance
Drive Capability
●
Continuously Variable Loudness Control
●
40-Station Random Preset Tuning
●
Automatic Preset Tuning
●
Preset Station Shifting Capability
●
IF Count Direct PLL Synthesizer Tuning
System
●
Remote Control Capability
RX-485 RDS and RX-385 RDS only
●
Multi-Functions for RDS Broadcast
Reception
RX-485 RDS only
●
Pure Direct Switch to Reproduce the
Purest Source Sound
4
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
3. Never open the cabinet. If something drops into the set, contact
your dealer.
4. Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wires themselves.
5. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
6. Always set the VOLUME control to “–
∞
” before starting the audio
source play. Increase the volume gradually to an appropriate level
after playback has been started.
7. Do not attempt to clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
8. Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
9. When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
10.To prevent lightning damage, disconnect the AC power plug and
disconnect the antenna cable when there is an electrical storm.
11.Grounding or polarization – Precautions should be taken so that
the grounding or polarization of an appliance is not defeated.
12.AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
13.Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
IMPORTANT
Please record the serial number of this unit in the space below.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
FOR CANADIAN CUSTOMER
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS SET OUT IN THE RADIO INTERFERENCE
REGULATION OF THE CANADIAN DEPARTMENT OF
COMMUNICATIONS.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wire in the mains lead are coloured in accordance with
the following code:
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug. Proceed as follows: the wire
which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in different
areas, set the FREQUENCY STEP switch (located at the rear)
according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of this unit
from the AC outlet.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
5
English
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
●
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
Connecting the AM loop antenna
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
Notes
●
When connecting the indoor
FM antenna, make sure that
the grooved part of the
connector hole is facing
downward.
●
If you need an outdoor
FM antenna to improve
FM reception quality, either 300-ohm feeder or coaxial cable
may be used. In locations troubled by electrical
interference, coaxial cable is preferable.
CONNECTIONS
75Ω
UNBAL
PHONO CD AUX
FM
ANT
GND
AM
ANT
TAPE
PB
300-ohm
feeder
75-ohm
coaxial cable
75-ohm/300-ohm
antenna adapter
Ground
Outdoor FM antenna
Indoor FM
antenna
(included)
Outdoor AM antenna
AM loop
antenna
(included)
Orient so that the best
reception is obtained.
➀
➁
➂
6
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
AUDIO CONNECTIONS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
* : Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
RX-485 RDS
R L
A
B
75Ω
UNBAL
PHONO CD AUX
A
B
FM
ANT
GND
AM
ANT
TAPE
PB
REC
OUT
TAPE 1
SPEAKERS
Video cassette player etc.
Turntable Compact disc player Tape deck 1
To AC outlet
Speakers A
Right Left
Right Left
Speakers B
TAPE
PB
REC
OUT
TAPE 2
Tape deck 2
R
L
OUTPUT
GND
REMOTE CONTROL
AUDIO OUT
LINE OUT
LINE IN
OUTPUT
LINE IN
LINE OUT
100W MAX. TOTAL
SWITCHED
AC OUTLETS
REMOTE
CONTR0L
PHONO
GND
(Europe model)
7
English
* : Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
RX-385, RX-385 RDS
R L
A
B
75Ω
UNBAL
PHONO CD AUX
A
B
FM
ANT
GND
AM
ANT
TAPE
PB
REC
OUT
TAPE 1
SPEAKERS
Video cassette player etc.
Turntable Compact disc player Tape deck
To AC outlet
Speakers A
Right Left
Right Left
Speakers B
R
L
OUTPUT
GND
AUDIO OUT
OUTPUT
LINE IN
LINE OUT
100W MAX. TOTAL
SWITCHED
AC OUTLETS
GND
(Europe model)
8
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut to be as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
●
One or two speaker systems can be connected to this unit.
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
●
Use speakers with the specified impedance shown on the
rear of this unit.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
Press up the tab.
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
➂
Press down the tab and
secure the wire.
CONNECTING SPEAKERS
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S)
(Europe model) ...................................2 SWITCHED OUTLETS
(U.K. model) ..........................................1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
REMOTE CONTROL (PHONO) connector
RX-485 RDS only
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector by using the cable provided
with the turntable. This connection allows you to control the
turntable from the provided remote control transmitter.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
➀
➁
➂
1
Set to the “
∞
” position.
2
3
Select a desired input source.
* The name of the selected input source will appear in the
display.
* Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
4
Select the speakers to be used.
* If you use two speaker systems, press both the A and B
switches.
5
Play the source. (For detailed information on the tuning
operations, refer to the page 12.)
6
Adjust to the desired output level.
7
If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (Refer to page 11.)
Notes
RX-485 RDS only
●
If you select AUX, TUNER, CD or PHONO, be sure that
TAPE 1 and/or TAPE 2 are not being selected.
●
If you select TAPE 1 and TAPE 2 at the same time, the
result will be the sound from the tape deck 1.
●
For TAPE 1 and TAPE 2, whenever the button is pressed,
the corresponding input source is selected or canceled
alternately.
RX-385 and RX-385 RDS only
●
If both TAPE MONITOR and another input selector button
are selected, TAPE MONITOR has priority.
9
English
OPERATIONS
TO PLAY A SOURCE
TAPE 1
MONITOR
COPY
INPUT
AUX TUNER
CD PHONO
TAPE 2
INPUT
AUX TUNER
CD PHONO
TAPE
MONITOR
SPEAKERS
A
B
ON
OFF
ON
OFF
3
7
1, 6
4
2
— dB
VOLUME
0
POWER
0
— dB
VOLUME
RX-485 RDS
RX-385, RX-385 RDS
10
1
Select the source to be recorded.
* To dub from tape to tape, refer to the “Notes” shown
below.
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE 1 and/or TAPE 2 are not also selected.
2
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 12.)
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the
input selector button for the tape deck being used to
make the recording.
SOURCE
Tape deck connected to
the TAPE 2 terminals.
RECORDER
Tape deck connected to
the TAPE 1 terminals.
Notes
●
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being
recorded.
●
To dub from tape to tape, only the following method of
dubbing can be performed.
TO RECORD A SOURCE TO TAPE
RX-485 RDS
TO RECORD A SOURCE TO TAPE
RX-385, RX-385 RDS
→
COPY
TAPE 1
MONITOR
INPUT
AUX TUNER
CD PHONO
TAPE 2
1, 4
2
1
Select the source to be recorded.
* When you select AUX, TUNER, CD or PHONO, be sure
that TAPE MONITOR is not also selected.
2
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 12.)
3
Begin recording on the tape deck.
4
To monitor the audio signals being recorded, press the
TAPE MONITOR.
Note
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being recorded.
INPUT
AUX TUNER
CD PHONO
TAPE
MONITOR
11
English
Using the PURE DIRECT switch
RX-485 RDS only
You can enjoy the purest possible sound from your audio
sources by setting this switch ON. By doing so, the audio
signal bypasses the BASS, TREBLE, BALANCE and
LOUDNESS controls, eliminating any alterations to the audio
signal.
When you listen with headphones
Connect the headphones to the PHONES jack. When listening
with headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
Adjusting the BASS and TREBLE
controls
Adjusting the BALANCE control Selecting the SPEAKER system
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
BASS : Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
1
Set to the “FLAT” position.
2
Set to the loudest listening level that
you would listen to.
3
Turn so that the desired volume can
be achieved.
BALANCE
0
L5
5R
BASS
DEFEAT
—
5 +
5
TREBLE
DEFEAT
—
5 +
5
LOUDNESS
FLAT
—
30dB
I0
LOUDNESS
FLAT
—
30dB
I0
SPEAKERS
A
B
ON
OFF
ON
OFF
PHONES
PURE DIRECT
0
— dB
VOLUME
12
FM/AM
AM
FM
1 Select the reception band (FM or AM) while watching
the display.
2
3 Tune to a desired station manually.
* To continue tuning search, press and hold the button.
1 Select the reception band (FM or AM) while watching
the display.
2
3
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stopped is not the
desired one, press again.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
Display information
➀
Displays the band and frequency of the received station.
RX-485 RDS and RX-385 RDS only
If an RDS station is received, the frequency is then
replaced by the station name. (However, if the PS data
cannot be received within 5 seconds, “NO PS” flashes,
and then it returns to the frequency display.)
Refer to page 17 for details.
➁
Illuminates when an FM stereo broadcast is received in
stereo.
➂
Indicates the signal level of the received station.
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
AUTOMATIC TUNING MANUAL TUNING
2
3
1
FM/AM
TUNING
MODE
AUTO
/
MAN’L
MONO
TUNING
MODE
AUTO
/
MAN’L
MONO
TUNING
DOWN
UP
TUNING
DOWN
UP
STEREO
0
MHz
40 60
20
l00
FM
➀ ➁
➂
➀➁
➂
STEREO
0
MHz
20
l00
FM
AUTO TUNING
“AUTO TUNING”
goes off.
or
AM
FM
or
RX-385
RX-485 RDS, RX-385 RDS
13
English
11 Select the page where the preset station is stored.
22
Select the preset station number.
1 Tune to a desired station.
(Refer to the previous page for tuning procedures.)
2
3 Select a desired page (A – E) of preset stations while
watching the display.
4
Select a preset station number (1–8) while watching the
display before “MEMORY” goes off from the display.
5
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations on other pages in the
same way by selecting other pages in step 3.
Notes
●
A new setting can be programmed in place of the former
one.
●
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
Memory back-up
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If so,
it can be re-programmed by simply following the PRESET
TUNING steps.
MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only
selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored.
To store stations To recall a preset station
3, 11
4, 22
2, 5
MEMORY
MAN’L/AUTO FM
MEMORY
MAN’L/AUTO FM
PRESET
MEMORY
FM
Flashes on and off
for about 5 seconds.
A/B/C/D/E
PRESET
MEMORY
FM
A/B/C/D/E
PRESET
MEMORY
FM
PRESET
STATIONS
DOWN
UP
PRESET
STATIONS
DOWN
UP
AUTO TUNING
PRESET
STEREO
0
MHz
40 60
20
l00
FM
Shows the displayed station
has been programmed to A1.
AUTO TUNING
PRESET
STEREO
0
MHz
20
l00
FM
Shows the displayed station
has been programmed to A1.
PRESET TUNING
RX-385
RX-485 RDS, RX-385 RDS
14
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 13.
RX-485 RDS and RX-385 RDS only
* Only RDS stations can be stored by this function.
To store stations
Press and
hold for about
3 seconds.
FM/AM
FM
MEMORY
MAN’L/AUTO FM
2
1
PRESET
MEMORY
AUTO TUNING
and
1
2
Flashes. Flashes.
After 5 seconds, the automatic preset tuning begins from A1.
Received stations are programmed to A1, A2 ... A8
sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the received first station to
C5, select “C5” by using the A/B/C/D/E button and the
PRESET STATIONS button soon after the display begins
flashing on/off in step 2. After a few seconds, the automatic
preset tuning begins. The received first station is stored to C5,
and next stations to C6, C7 ... sequentially.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 13.
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 13.
RX-485 RDS and RX-385 RDS only
* A recalled station is shown by the frequency or station name
on the display.
Notes
●
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 13.
RX-385 only
●
If the number of received stations is not enough to be stored
up to E8, the search is finished automatically when it
reaches the highest frequency after searching through all
frequencies.
●
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is week in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 13.
RX-485 RDS and RX-385 RDS only
●
The automatic preset tuning search will be performed
through all RDS network frequencies until stations are
stored up to E8. If the number of received stations is not
enough to be stored up to E8, the search is finished
automatically after searching through all frequencies.
●
With this function, only RDS stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 13.
* There may be a case that this function cannot receive a
station which could be received by the automatic tuning
method. This is because this function receives a large
volume of PI (Program Identification) data along with the
station.
15
English
1 Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 13).
2
3 Next, recall the preset station on A5 by following the
same method with step 1.
4
Shows the exchange of stations is completed.
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations each other by easy operations.
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
Flashes
Flashes
EDIT
EDIT
2, 4
RECEIVING RDS STATIONS
RX-485 RDS
and
RX-385 RDS
only
RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations
using this system transmit an inaudible stream of data in addition to the normal radio signal.
RDS data contains various information, such as AF (Alternative Frequencies for the same program station), PI (Program
Identification), PS (Program Service station name), PTY (Program Type name), etc.
RDS function is carried out among the network stations.
* This unit utilizes AF, PI, PS and PTY to receive RDS broadcast stations.
Displaying RDS data
This unit can be turned into the following two modes to display RDS data.
PS (Program Service station name) mode:
Displays the name of the RDS station now being received instead of the frequency.
PTY (Program Type name) mode:
Displays the program type of the RDS station now being received. There are 15 program types to classify RDS stations as follows.
16
News:
Short accounts of facts, events and publicly
expressed views, reportage and actuality.
Current affairs:
Topical program expanding or enlarging
upon the news, generally in different
presentation style or concept, including
documentary debate, or analysis
Information:
Program whose purpose is to impart advice
in the widest sense, including meteorological
reports and forecasts, consumer affairs,
medical help, etc.
Sport:
Program concerned with any aspect of sport.
Education:
Program intended primarily to educate, of
which the formal element is fundamental.
Drama:
All radio plays and serials.
Culture:
Programs concerned with any aspect of
national or regional culture, including
religious affairs, philosophy, social science,
language, theatre, etc.
Science:
Programs about the natural sciences and
technology.
Varied:
Used for mainly speech-based programs
usually of light-entertainment nature, not
covered by above categories. Examples are:
quizzes, panel games, personality interviews,
comedy and satire.
Pop:
Commercial music, which would generally be
considered to be of current popular appeal,
often featuring in current or recent record
sales charts.
Rock:
Contemporary modern music, usually written
and performed by young musicians.
M.O.R.:
(Middle of the Road Music). Common term to
describe music considered to be “easy-
listening”, as opposed to Pop, Rock or
Classical. Music in this category is often but
not always, vocal, and usually of short
duration (<5 min.)
Light classics:
Classical Musical for general, rather than
specialist appreciation. Examples of music in
this category are instrumental music, and
vocal or choral works.
Serious classics:
Performances of major orchestral works,
symphonies, chamber music etc., and
including Grand Opera.
Other music:
Musical styles not fitting into any of the
above categories. Particularly used for
specialist music, of which Jazz, Rhythm &
Blues, Folk, Country, and Reggae are
examples.
BBC R3
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
MOR M
LIGHT M
CLASSICS
OTHER M
17
English
To turn the unit into the PS mode or PTY mode
Press the FREQ/PS/PTY button. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in
turn.
* When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button
until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that “NO
PS” flashes on the display. This is because the unit has not received all of the RDS data on the station yet.
PS mode The name of the station being received is displayed.
If the station is not an RDS station, “NO PS” flashes on the
display and then returns to usual mode.
PTY mode A program type for the station being received is displayed.
If the RDS station does not employ the PTY data service,
“NO PTY” flashes on the display and then returns to the PS
mode.
If the station is not an RDS station, “NO PTY” flashes on the
display and then returns to usual mode.
Usual mode The frequency of the station being received is displayed.
Note
When PS or PTY data reception is not possible due to poor reception conditions, “NO PS” or “NO PTY” flashes on the display in
each mode. In such a case, press the TUNING MODE button so that “AUTO TUNING” goes off from the display. Though the
reception mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be
displayed.
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
18
1
2 Turn the unit into the PS mode.
* If “NO PS” flashes, proceed to the next step while flashing.
If “NO PS” disappears before you proceed to the next step,
press the FREQ/PS/PTY button again.
3
4 Select the first letter or numeral of the station name.
* By pressing the TUNING button repeatedly or by pressing
and holding it, the display will change letters and numerals
in sequence.
* If you will not input the second letter, skip to step 7.
5 When the first letter or numeral of the station name
appears, press the SHIFT button to proceed to the
selection of the next letter or numeral.
6 Repeat steps 4 and 5 for other letters and/or numerals,
if necessary.
7 When inputting the name is finished, press the ENTER
button.
8
The unit begins searching for the station, and it is
continued until the station is found.
You do not have to input a full name for searching
for the station
You may input only the first letter of the station name. If doing
so, you can skip steps 5 and 6. In step 8, the unit searches
for and calls a nearest station which has the letter you input. If
the station is not the desired one, press the PRESET
STATIONS button again. The unit will begin searching for
another station which has the same letter.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or
MEMORY button.
Notes
●
If no station is found by this function after searching all
preset stations, “NO PS” flashes for about 3 seconds on
the display, and then it returns to the mode which had
been obtained before the searching was performed.
●
This function is useful especially for calling a station with
weak signals which cannot be received by the automatic
tuning method. By only storing such a station, you can call
it any time easily.
Calling a preset RDS station by the station name (PS SEEK)
You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation,
this unit searches all preset stations for the station. You do not have to input a full name, even only the first letter can be used for
calling. As many as 8 letters and/or numerals can be selected for inputting a name.
A station name
is displayed or
“NO PS” flashes.
Flashes.
Flashes.
“A” will flash on the second
letter or numeral position.
Press once.
FM/AM
FM
ENTER
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
PRESET
STATIONS
DOWN
UP
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
TUNING
DOWN
UP
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
2, 3, 5, 7
4 8
1
19
English
Calling a preset RDS station by the program type (PTY SEEK)
By designating a program type, the unit automatically searches all preset stations for RDS stations of that program type.
* There are 15 program types to classify RDS stations. For details, refer to page 16.
1 Turn the unit into the PTY mode.
* If “NO PTY” flashes, proceed to the next step while
flashing. If “NO PTY” disappears before you proceed to the
next step, press the FREQ/PS/PTY button once or twice.
2
3 Select the desired program type.
* By pressing the TUNING button repeatedly or by pressing
and holding it, the display will change program types in
sequence.
4 When the desired program type appears, press the
ENTER button.
5
The unit begins searching all preset stations, and calls a
station of the program type if such a station is found.
* When the right side of the PRESET STATIONS button is
pressed, the search is performed from “A1” toward higher
numbers of the preset stations (A1, A2 ... A8, B1, B2, ...).
If, however, “A3” is currently being called for example, the
search begins from the next station “A4”.
When the left side of the PRESET STATIONS button is
pressed, the search is performed in reverse order.
If the called station is not the desired one, press the
PRESET STATIONS button again to search for another
station of the same program type.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or
MEMORY button.
Note
If no station is found by this function, after searching all preset
stations, “NO PTY” flashes for about 3 seconds on the
display, and then it returns to the mode which had been
obtained before the searching was performed.
Press once or twice until a
program type is displayed
or “NO PTY” flashes.
Flashes.
The program type of the station now being
received or “NEWS” flashes on the display.
Press once.
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
PRESET
STATIONS
DOWN
UP
FREQ/PS/PTY SHIFT ENTER
PS/PTY SEEK
TUNING
DOWN
UP
1, 2, 4
3 5
ENTER
20
Calling the best quality RDS station which broadcasts the
same program (AF SEEK)
This function automatically searches for and calls another RDS station of the best reception quality which broadcasts the same
program now you are listening to.
This function utilizes AF (Alternative Frequencies for the same program station) and PI (Program Identification) of RDS data service.
The search is carried out among the RDS network stations.
1 Tune to a desired RDS station.
* Wait for about 10 seconds before proceeding to the
next step. This is for making this unit carry out
searching more stations.
2
The unit searches network stations for other stations with
the same program.
* If the station is not an RDS station, or there is no other
station with the same program, “NO AF” flashes.
Stations with the same program are all stored and
numbered from the best quality station in sequence.
When the search is finished, the best quality station is
called.
3 If desired, you can call the second station by pressing
the AF button.
Whenever the AF button is pressed, stored stations are
called in sequence.
When pressed after the last station is selected, the first one
is restored.
To cancel this function
Press a button other than the AF button.
All of the stored stations will be also cleared.
AF
AF
2, 3
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25

Yamaha RX-V385 Manuale utente

RX-V385
Yamaha
Marca
Yamaha
Modello
RX-V385
Categoria
Lettori di cassette
Tipo
Manuale utente
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti