CAME S500R Manuale utente

S500R

W

A

R

A

N

T

Y

•

G

A

R

A

N

T

I

E

•

G

A

R

A

N

Z

I

A

•

G

A

R

A

N

T

I

A

•

G

A

R

A

N

T

I

E

•

G

A

R

A

N

T

I

E

•

Y

E

A

R

S

•

A

N

S

•

A

N

I

•

A

Ñ

O

S

•

A

N

O

•

J

A

H

R

E

•

3

Installation

manual

OPERATOR

FOR

OVERHEAD GARAGE

OR SECTIONAL DOORS

surface area

of the door

9 m2 max

English

Français

Italiano

Español

Português

Deutsch

Türk

2

-

FG00705M07

-

1

- 09/2017

ENGLISH

SUMMARY

GENERAL PRECAUTIONS .. .............................................................3

KEY ...............................................................................................5

DESCRIPTION . ..............................................................................5

Intended use ............................................................5

Operating limits .......................................................5

Technical data ... .......................................................6

Dimensions .. ............................................................ 6

Description of parts ... ..............................................7

Standard installation .. ..............................................8

INSTALLATION ..............................................................................9

Preliminary checks . ..................................................9

Applicative examples .. ............................................ 10

Cable type and minimum thicknesses ... .................... 11

Assembling the traction guide .... .............................. 12

Positioning the traction guide .................................. 12

Fastening the traction guide . .................................. 13

Fitting the transmission arm to the door . ................. 14

Fitting the operator to the guide .............................. 14

Moving the micro switch . ....................................... 15

ELECTRICAL CONNECTIONS .... .....................................................17

Input voltage .......................................................... 17

Movement control and obstacle detection ......... ........ 17

Description of parts ... ............................................ 18

Command and control devices .... .............................. 19

Safety devices .. ..................................................... 19

Signaling devices .... ................................................20

Preparing for programming ... ..................................20

Description of keys ................................................21

Obligatory functions ... ............................................ 21

Optional functions .. ................................................23

Additional external antenna ... ..................................26

Radio frequency card . ............................................26

Memorizing the transmitters ..................................27

Deleting transmitters . ............................................27

DISMANTLING AND DISPOSAL .....................................................28

DECLARATION OF CONFORMITY ....................................................28

3

-

FG00705M07

-

1

- 09/2017

ENGLISH

CAUTION: Important safety instructions.

Follow all instructions. Improper installation may lead to serious

bodily injuries. Before continuing, also read the precautions in the

operating and maintenance manual.

GENERAL PRECAUTIONS

This product must only be used for its speciﬁ cally intended

purpose. Any other use is dangerous. LABEL HABITAT SAS

is not liable for any damage caused by improper, wrongful or

unreasonable use of this product. • This manual's product

is deﬁ ned by machinery directive 2006/42/CEas "partly-

completed machinery". Partly-completed machinery is a set

that almost constitutes a machine, but which, alone, cannot

ensure a clearly deﬁ ned application. Partly-completed

machinery is only destined to be incorporated or assembled

to other machinery or other partly-completed machinery or

apparatuses to build machinery that is regulated by Directive

2006/42/CE. The ﬁ nal installation must be compliant with

European directive 2006/42/CE and European reference

standards: EN 13241-1, EN 12453, EN 12445 and

EN 12635. Given these considerations, all procedures

stated in this manual must be exclusively performed

by expert, qualiﬁ ed staff.• The operator cannot be

used with gates ﬁ tted with pedestrian doors, unless

its operation can be activated only when the pedestrian

door is in safety position • Make sure that people are not

entrapped between the gate's moving and ﬁ xed parts due

to the gate's movement • Before installing the operator,

check that the gate is in proper mechanical conditions, that

it is properly balanced and that it properly closes: if any of

these conditions are not met, do not continue before having

met all safety requirements • Make sure that opening and

closing limiters are ﬁ tted • Make sure the operator is

installed onto a sturdy surface that is protected from any

impacting shocks • Make sure that mechanical stops are

already installed • If the operator is installed lower than

2.5 from the ground or from any other access level, ﬁ t any

protections and signs to prevent hazardous situations •

Do not ﬁ t the operator upside down or onto elements that

could yield to its weight If necessary, add reinforcements

to the fastening points • Do not install door or gate leaves

on tilted surfaces • Check that no lawn watering devices

spray the operator with water from the bottom up •

Suitably section off and demarcate the entire installation

site to prevent unauthorized persons from entering the

area, especially minors and children • Fit cautionary signs,

4

-

FG00705M07

-

1

- 09/2017

ENGLISH

such as the gate plate, wherever needed and in plain sight.

• Use proper protections to prevent mechanical hazards

when people are loitering around the machinery's range

of action, for example avoid crushing of ﬁ ngers between

the drive shaft and the mechanical stops, avoid crushing

when the gate is opening • The electrical cables must run

through the cable glands and not touch any parts that may

overheat, such as the motor, transformer, and so on • All

command and control devices must be installed at least

1.85 m from the perimeter of the gate's range of action

or where they cannot be reached through the gate from

the outside • All switches in maintained action mode must

be positioned so that the moving gates leaves, the transit

areas and vehicle thru-ways are completely visible, and yet

the switches must be also away from any moving parts •

Unless a key switch is used, all control devices must be

ﬁ tted at a height of at least 1.5 mand wherethey are not

accessible to the public • Before handing over to users,

check that the system is compliant with the 2006/42/

CEuniformed Machinery Directive.Make sure that the

operator has been properly adjusted and that the safety

and protection devices, and the manual release, are working

properly • Afﬁ x a permanent tag, that describes how to

use the manual release mechanism, close to the mechanism

• Make sure to hand over to the end user, all operating

manuals for the products that make up the ﬁ nal machinery

• Set up a suitable dual pole cut off device along the power

supply that is compliant with the installation rules. It should

completely cut off the powersupply according to category III

surcharge conditions • The gearmotor must be exclusively

powered by very low safety voltage, which corresponds to

what is stated in the markings on the motor itself, and by

using the control panel supplied in the KIT.

5

-

FG00705M07

-

1

- 09/2017

ENGLISH

KEY

This symbol shows which parts to read carefully.

This symbol shows which parts describe safety issues

This symbol shows which parts to tell users about.

THE MEASUREMENTS, UNLESS OTHERWISE STATED, ARE IN MILLIMETERS. THE CONTENTS OF THIS MANUAL MAY CHANGE, AT ANY TIME, AND WITHOUT NOTICE.

DESCRIPTION

Complete system with control board, device for controlling the movement and the obstruction detection for overhead garage and

sectional doors with maximum surface area of 9 m2.

Intended use

This operator is designed to power overhead garage and sectional doors used in homes and apartment buildings.

 Any installation and/or use other than that speciﬁ ed in this manual is forbidden.

Operating limits

Model S500R

Door surface area (m2) 9

Maximum height of counterbalanced overhead doors (m) 2.4

Maximum height of spring-balanced overhead doors (m) 3.25

Maximum height of door (m) 3.20

6

-

FG00705M07

-

1

- 09/2017

ENGLISH

Dimensions

(mm)

Technical data

Model S500R

Protection rating (IP) 40

Power supply (V - 50/60 Hz) 230 AC

Motor power supply (V) 24 DC

Draw when in stand-by (W) 7

Power (W) 100

Opening speed (m/min) 6

Thrust (N) 600

Cycles/hr 30

Operating temperature (°C) -20 ÷ +40

Apparatus class II

Weight (Kg) 4.9

Acoustic pressure level (dB (A)) ≤70

210115

365

3020 ÷ 4020

7

-

FG00705M07

-

1

- 09/2017

ENGLISH

Description of parts

1. Operator

2. Power supply cable

3. Chain operated slide rail

4. Rail-supporting braces

5. Head braces for rails

6. Door fastening brace

7. Supporting braces

8. Perforated tabs for fastening the rail

9. Curved lever

10. Transmission arm

Release cord

8

-

FG00705M07

-

1

- 09/2017

RX

TX

6

1

57

6

2

3

4

ENGLISH

Standard installation

1. Operator with receiver

2. Slide guide

3. Release device

4. Transmission arm

5. Key-switch selector

6. Photocells

7. Keypad

9

-

FG00705M07

-

1

- 09/2017

ENGLISH

Preliminary checks

Before beginning the installation, do the following:

• make sure you have set up a suitable dual pole cut off device along the power supply that is compliant with the installation rules.

It should completely cut off the power supply according to category

III surcharge conditions (that is, with minimum contact openings of

3 mm);

• Setup suitable tubes and conduits for the electric cables to pass

through, making sure they are protected from any mechanical

damage;

• make sure that any connections inside the container (ones that

ensure continuity to the protection circuit) are fitted with additional

insulation with respect to those of other electrical parts inside:

• make sure that the door is properly balanced. When stopped at any

point, it must maintain its position.

INSTALLATION

Only skilled, qualiﬁ ed staff must install this product.

If the door is ﬁ tted with a pedestrian door, you must also ﬁ t a safety switch at the entrance, to stop the operator from working

when the pedestrian door is open.

10

-

FG00705M07

-

1

- 09/2017

(

H - 100 mm

H

H - 100 mm

H

((

ENGLISH

Applicative examples

* single rail

sectional door

* double rain

sectional door

SECTIONAL DOOR

COUNTERBALANCED OVERHEAD,

protruding and partially-retracting door (needs the 801XC-0060

adapter arm)

SPRING-BALANCED OVERHEAD DOOR,

fully retracting and protruding

11

-

FG00705M07

-

1

- 09/2017

ENGLISH

Cable type and minimum thicknesses

Connection cable length

< 20 m 20 < 30 m

Control board power supply 230 V AC (1P+N) 2 x 1.5 mm22 x 2.5 mm2

Flashing light 2 x 0.5 mm2

Command and control devices 2 x 0.5 mm2

TX Photocells 2 x 0.5 mm2

RX photocells 4 x 0.5 mm2

 When operating at 230 V and outdoors, use H05RN-F-type cables that are 60245 IEC 57 (IEC) compliant; whereas indoors, use

H05VV-F-type cables that are 60227 IEC 53 (IEC) compliant. For power supplies up to 48 V, you can use FROR 20-22 II-type cables

that comply with EN 50267-2-1 (CEI).

 If cable lengths differ from those specified in the table, establish the cable sections depending on the actual power draw of the

connected devices and according to the provisions of regulation CEI EN 60204-1.

 For multiple, sequential loads along the same line, the dimensions on the table need to be recalculated according to the actual power

draw and distances. For connecting products that are not contemplated in this manual, see the literature accompanying said products

12

-

FG00705M07

-

1

- 09/2017

M6x80 M6

10 ÷ 20

801XC-0060

20 ÷ 30

max 330

ENGLISH

The following illustrations are just examples, in that the space available for fitting the operator and accessories varies depending on the

overall dimensions. It is up to the installer to find the most suitable solution.

Assembling the traction guide

Fitting the brace to the transmission guide use the supplied nut and bolt .

Positioning the traction guide

for sectional doors exceeding the overall dimensions of the spring-pole brace.

for overhead doors between 10 and 20 mm from the apex point of the leaf's slide arc.

for partially retracting protruding counter-balanced overhead doors, use the 801XC-0060 arm (see the enclosed technical literature).

13

-

FG00705M07

-

1

- 09/2017

?

ENGLISH

Fastening the traction guide

Fasten the traction guide to the center of the doorway, using suitable screws.

Raise the guide and position in horizontally to measure the distance to the ceiling, then fasten it.

Instal the support braces and the U-shaped brace onto the guide.

Bend the perforated flat tabs so they fit snugly and so as to compensate for the distance between the guide and ceiling.

Fasten the flat tabs to the support braces and to the U-shaped brace using the supplied screws and washers. Drill the ceiling so the

holes match those on the flat tabs.

Fasten the flat tabs to the ceiling using suitable dowels and screws.

14

-

FG00705M07

-

1

- 09/2017

ENGLISH

Guide

Drive shaft with adapter

Self-drilling 6 x 15 screw

U-shaped brace

Micro

Fitting the operator to the guide

Fit the adapter to the drive shaft.

The operator can be fitted onto the guide:

either in standard position or at a right

angle .

Fit the transmission arm brace to the upper beam of the door, perpendicularly to the traction guide and fasten it using the supplied

screws or other suitable fasteners.

If mounting the curved lever fit it to the transmission arm by using the supplied nuts and bolts

Fitting the transmission arm to the door

15

-

FG00705M07

-

1

- 09/2017

ENGLISH

Moving the micro switch

Disconnect the cables of the micro switch and remove the latter.

If the operator is to be fitted at a right angle, before

installing it, set the micro-switch (see the corresponding

paragraph).

Self-drilling 6 x 15 screw

U-shaped brace

Guide

Drive shaft with adapter

Micro

16

-

FG00705M07

-

1

- 09/2017

ENGLISH

Remove the operator's cover and the gable brace. Pull out the electrical cable and fit it through the hole.

Refit the cable brace so as to block the hole.

Use a screwdriver to open up the predrilled hole for the electrical cables of the micro switch and fir the cables to the micro switch. Fit

the micro switch to the operator.

Connect the connectors to the corresponding positions on the micro switch.

Reconnect the cables as originally connected (NO - C).

Fit the cover back onto the operator.

17

-

FG00705M07

-

1

- 09/2017

ENGLISH

When CLOSING: inverts the direction of travel until opening is

complete.

After three consecutive inversions, the door stays open and exclu-

des the automatic closing: to close, either use the transmitter or

button.

When OPENING; the door stops. To resume movement, either press

a button or use the transmitter.

Movement control and obstacle detection

ELECTRICAL CONNECTIONS

Before powering up the board, cut off the mains power supply.

Power supply (V - 50/60 Hz): 230 AC

Board functions:

• Movement control and obstacle detection

• Reopening during closing

• Adjustable automatic reclosing time

• Open-stop-close-stop from transmitter and/or from button

• Courtesy light (at each opening command, the courtesy light stays on for three

minutes))

FUSES

- Line 5 A F

LIGHTS

LED courtesy (W) ≤ 1

Input voltage

The operator is supplied with an electrical cable (L = 1.2 m) with an already connected Shuko plug.

18

-

FG00705M07

-

1

- 09/2017

AF

4

2

8

91011

3

1

13

14 16

7

15

6

5

12

ENGLISH

Description of parts

1. Line fuse

2. Gearmotor

3. Transformer

4. Cables input

5. AF card connector

6. Antenna cable

7. Photocells connection terminal board

8. STOP button connection terminal board

9. Limit switch connection terminal board

10. Encoder connection terminals

11. Display connection terminal board

12. Motor connections

13. Transformer connections

14. Courtesy light connection terminal board

15. Antenna connection terminals

16. Flashing light connection terminal boards

19

-

FG00705M07

-

1

- 09/2017

RX

TX

ENGLISH

Command and control devices

Function OPEN-STOP-CLOSE-STOP from a control device (NO contact).

STOP button (NC contact). FOR stopping the door while excluding the automa-

tic closing. To resume movement either press the control button or any other

control device.

If a device is connected, remove the bridge

If a device is connected, remove

the bridge

Safety devices

- Marketed buttons.

- Optional key-switch selector, KEYSTAR item.

20

-

FG00705M07

-

1

- 09/2017

ENGLISH

Flashing light (contact rated for: 24 V - 25 W max).

It flashes during opening and closing.

Signaling devices

Preparing for programming

Manually hook up the door to the skid.

Power up the operator. After emitting a sound signal, the control board is ready for programming.

Remove the transparent panel to access the programming keys.

Memorizing (function 5) must always be the last phase of programming, otherwise the settings will not be saved.

In the case of errors, cut off and the power up again the mains power and reprogram.

PROGRAMMING DEVICE -

La pagina sta caricando ...

CAME S500R Manuale utente

Questo manuale è adatto anche per

CAME S500R Manuale utente

in altre lingue

Documenti correlati

Altri documenti