This product supports GPS positioning and is recommended for outdoor flight!
* This wifi camera pinpoint is 5G, please confirm whether the phone is supported.
This product is suitable for users over 14 years old.
Stay away from the rotating propeller
Please read the guidelines before using them, and
follow all security precautions.
Note
Li-Po Battery Disposal & Recycling
Wasted Lithium-Polymer batteries must not be placed with household
trash. Please contact local environmentalor waste agency or the
supplier of your model or your nearest Li-Po battery recycling center.
Our company's products are improving all the time, design and specifications
are subject to change without notice. All the information in this manual has
been carefully checked to ensure accuracy, if any printing errors, our company
reserve the final interpretation right.
Important
Notice
U39S / U43 / U43S
V1.0
QUICK START GUIDE
SD card slot
Download the
Operation Guide
Drone preparation
Navigation lights (Red)
Navigation lights (Red)Navigation lights (Red)
Propeller A
Propeller A
Battery
indicator
Power switch
Front folding arm
Propeller B
Propeller B
Rear folding arm
Front
Camera gimbal
Bottom view
Navigation lights (Green)
Rear
Tripod
Tripod
Drone
battery
Operation
tutorial
02
Drone battery
Unfolding Instruction
① ②
Folding State 1) Rear folding arms unfold
2) Front folding arms unfold 3) Open the tripod
Drone battery charging
Connect the Drone-battery to charging port with
included USB charger cable, and then connect to other
USB output port (Output: 5V, ≥2A). Battery indicator
flashes when charged, and always on when fully
charged. Support QC3.0 fast charging protocol.
Battery power is low in the original factory, It must be fully charged before use.
Power adapter (not included)
Input: 5V, ≥2A
Warning: Must be supervised while charging
Please use the included USB charging cable and make sure it is properly connected.
03
Battery
Compartment
Drone battery
Insert batteries along the tail.
Remove: Press the double unlock and pull out the battery backwards.
When the drone's battery put into the
battery compartment and the contact
is connected, it will sound "ka", that it
indication the battery is successfully
installed.
Insert the SD card into the slot in the drone's body.
Please make sure the metal contact facing. After
installation, the SD card can be used normally only
after formating in "Setting-other" of the APP.
Note:
High-quality video or photo shooting requires the
storage device to support fast writing. Use a micro
SD card with UHS-I Speed Grade 3 or higher
specifications to ensure the shooting performance.
Please do not insert or remove the SD card when
the drone is turned on or remove the battery when
the power is turned on. Otherwise, the SD card may
be damaged and data may be lost.
Installation of drone battery
Install an SD card (Not Include)
04
Input: ≤5V, ≥1A
Transmitter preparation
Phone Holder
Video
Left stick
Gimbal back to
central/down GPS switch
Right Stick
Power switch
The GPS indicator is White when using ordinary transmitter
( The GPS indicator is Green when using PA transmitter)
Transmitter power
indicator
Return/Pause
Speed switch
Gimbal Rotary Button Photo
Battery power is low in the original factory, It must be fully charged before use.
Power adapter (not included)
Transmitter charging
Connect the transmitter to charging port with included USB charger
cable, and then connect to other USB output port (Output: ≤5V, ≥1A).
the transmitter indicator flashes circularly when charged, and always
on when fully charged.
Warning: Must be supervised while charging
Please use the included USB charging cable and make sure it is properly connected.
①②
05
Pull up
Back of transmitter
Top of transmitter
Bottom support clamp
Upper support clamp
Installation of phone holder and phone
Flight Operations
Mobile phone connect with Drone
Download and install APP: UDIRC-X
This software is suitable for mobile phones in the
IOS 9.0 or later and Android 4.4 or later system.
For detailed operation, please check the system
“HELP” of APP.
Place the phone in the upper and bottom support clamps Between, the
clamp will automatically clamp the mobile phone .
Notice:
Don't clip the buttons on
the side of the phone.
Phone
06
Horizontal Ground
GPS Signal Search
After the frequency paring is successful, the drone will search for GPS
signal automatically. When the transmitter sounds "di", it indicating the
GPS connection is successful.
(When the GPS signal is weak or flying indoors, the flight height defaults
to about 4m.)
Transmitter connect with Drone
Frequency Pairing
1) Press 2 seconds to turn on
the power of the transmitter and
the indicator will flash, then enter
to wait for frequency pairing.
Press 2 seconds to turn off the power.
2) Press 2 seconds to turn on the power of the drone and the
front navigation will keep bright. When the transmitter sounds "didi"
indicates that the frequency is successful. The indicator light of the
transmitter will keep bright and the navigation light flashes cyclically
to enter GPS signal search state.
Press 2 seconds to turn off the power.
The frequency paring time of PA transmitter is 30-60 seconds, please
make sure no operation during frequency pairing.
07
①
②
Unlocking/locking the motor
Push the left and right stick inward to
the 45° angle simultaneously.
When the compass is affected by geomagnetic interference, it will be
notified in APP. Please follow the instructions.
On standby drone, motor rotation,
drone unlocked.
When the drone is not take off, the
motor stops rotating and the drone
is locked.
The drone can only take off when the motor is unlocked.
Counter-
clockwise
turn
Clockwise
turn
Go up
Go down
Fly to
the left
Fly to
the right
Forward
Backward
Control stick operation
Left stick Right stick
Compass calibration
08
After unlocking the motor,
the left stick slowly pushes up
and the drone slowly rises.
Press at once,
gimbal turn down;
Press again,
gimbal back to center
During the flight, press " " button, and the transmitter
will sound "di" then the drone will return to the take off point
automatically. During the drone return, the power indicator of the
transmitter flashes circularly.
To stop the return, press this button again.
Note:
During the return, the right sitck are not able to control the drone.
It must wait until the drone returns to the take off point and keeps
in the same direction as the take off, the right stick can control the
drone.
Landing
During the flight, the left stick
slowly pull down , and the drone
slowly lands until landing.
Return
Stop Return
Take off
09
Long press, the transmitter will sound "di..." to turn off the GPS.
After repeated operation, the transmitter will sound "di" to turn
on the GPS.
Note:
this function is only
used when the motor
is locked. If you want
to fly indoor please
turn off the GPS
function first.
GPS is on by default.
GPS ON /OFF
Roll Gimbal Rotary Button, adjust Camera Angle.
Photo
Press the button once
to take a picture and
the transmitter will
sound "di".
Video
Press the button for 2 seconds, the
transmitter will sound "di..." to start
recording. Repeat this action to stop
recording and save the video.
CINE: Low speed
NORMAL: Medium speed
SPORT: High speed
Gimbal Adjustment
10
1) Photos taken will be saved to mobile picture library and drone SD
card; Video can be saved in SD card first.
2) The APP must be authorized to read the phone gallery to view the
aerial photos.
3) Turn off the power supply of the drone before taking out the SD card.
4) When aerial video is read by computer, it must have corresponding
playback software.
The function is standard by the mobile phone App signal, so it’s a must
to make the drone and App connected normally, turn on the mobile
location service at the same time, otherwise this function is invalid.
Follow the APP guide to operate.
Follow the APP guide to operate.
Following Function
Encircling flight
In the state of encircling flying, the left stick could only control the height of the drone.
Notes for Filming
Low Battery Alarm
When the battery power of the transmitter is running out, it will sound
of "didi" and the power indicator flashes. This moment, please return
soon and charge the transmitter.
Turn left, the drone
flies clockwise; Move
further, the flying
speed will become
faster.
Go downside to enlarge the radius of encircling.
Go upward to narrow the radius of encircling.
Turn right, the drone
flies counterclockwise;
Move further, the
speed will become
faster.
11
Stuck Protection
When the propeller is stuck and does not rotate, the drone will start the
automatic protection function to stop the motor working.
Out of Control Protection
Out of control protection refers to the flight control system automatically
controls the drone to fly back to the return point after receiving the
remote control signal (ie, out of control), the drone does not have the
function of avoiding obstacles during the uncontrolled return flight. The
user can set the return altitude value to avoid obstacles on the way back.
* The remote control is off.
* Flight distance exceeds the effective distance of remote control signal
transmission.
* There is an obstacle between the transmitter and the drone.
* Transmitter signal is disturbed.
Possibility of entry into runaway protection mode
Automatic Return
When the drone is out of the remote control distance, the transmitter
will sound "di-di" to alarm the user to return the drone immediately.
When the battery power of the drone is runnign out, there will be an
alarm on the APP interface and the navigation light will change from
long bright to flash light. This moment, the drone will automatiocally
return to the air above take off point.
Out of range alarm
12
FCC Note
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interferencein a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving a ntenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which
thereceiver is connected.
WARNING: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
The equipment may generate or use radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless the modifications are expressly
approved in the instruction manual. Modifications not authorized by the manufacturer may
void user’s authorityto operate this device.
1) Switching sequence. At first, turn on the power of the transmitter, then turn on
the power of the drone. After the end, turn off the power of the drone first, and
then turn off the power of the transmitter.
2) Improper operation caused the crash. It is necessary to check and confirm the
connection of the motor, blade or electric pool of the drone and the damage
degree, so that the drone can fly again. If it is damaged, please replace it with
new accessories, otherwise it will easily cause flight accidents.
3) Battery must be removed when the drone is not in use.
Attention
13
DANGER!
Only suitable
for age 14+
Warning: The product should only be used by adults and children over 14 years.
Adult supervision is required for children under 14 years.
Hinweis: Dieses Produkt ist für die Erwachsene und die Kinder ab 14 Jahren.
Die kinder unter 14 Jahren müssen von Erwachsenen beaufsichtigt werden.
Avertissement: Ce produit est destiné aux adultes et aux enfants de plus de 14 ans.
Les enfants de moins de 14 ans doivent être surveillés par des adultes.
Avvertimento: Questo prodotto è destinato all'uso per i adulti e bambini di età superiore ai 14 anni.
I bambini di età inferiore ai 14 anni devono essere sorvegliati da un adulto.
Advertencia: Este producto es para adultos y niños mayores de 14 años.
Los niños menores de 14 años deben ser supervisados por adultos.
WARNING
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition with out restriction.
FCC Radiation Exposure Statement
MADE IN CHINA
Address: Guangfeng Industrial Zone, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, CN
Manufacturer: UDIRC TECHNOLOGY CO., LTD
14
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
in altre lingue
- English: udiR C U39S User guide
Altri documenti
-
dji Matrice 600 Pro Guida utente
-
dji Phantom 3 SE Guida utente
-
dji Mavic Air 2 Guida utente
-
dji Mavic 2 Pro Istruzioni per l'uso
-
dji Mavic 2 Zoom Istruzioni per l'uso
-
QIMMIQ FREON Guida Rapida
-
dji AIR 2S Guida utente
-
-
-
