Bosch PXX895GA6(00) Istruzioni per l'uso
- Categoria
- Piani cottura
- Tipo
- Istruzioni per l'uso
3FHJTUFS
ZPVS
OFXEFWJDFPO
.Z#PTDIOPXBOE
HFUGSFFCFOFGJUT
CPTDIIPNFDPN
XFMDPNF
[en] Instruction manual Hob
Induction hob with integrated
ventilation system
PXX...D6..
2 Ø = cm
:
: :
:
:
,(&
2 Ø = cm
:
: :
:
:
,(&
en
3
Table of contents
[en]I ns t r u ct i on manual Hob
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
( Important safety information . . . . . . . . . . . . . . . 6
] Causes of damage . . . . . . . . . . . . . . . . . . . . . . . . 8
7 Environmental protection . . . . . . . . . . . . . . . . . . 8
Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Environmentally-friendly disposal . . . . . . . . . . . . . . . . . 8
f Induction cooking . . . . . . . . . . . . . . . . . . . . . . . . 9
Advantages of induction cooking . . . . . . . . . . . . . . . . . 9
Cookware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
* Getting to know your appliance . . . . . . . . . . . . 11
Your new appliance . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Special accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 11
The control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
The hotplates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Residual heat indicator. . . . . . . . . . . . . . . . . . . . . . . . 13
Ç Operating modes . . . . . . . . . . . . . . . . . . . . . . . . 14
Exhaust air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Air recirculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
K Before using for the first time. . . . . . . . . . . . . . 14
Setting Home Connect . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the operating mode . . . . . . . . . . . . . . . . . . . . 14
1 Operating the appliance . . . . . . . . . . . . . . . . . . 15
Switching the hob on and off . . . . . . . . . . . . . . . . . . . 15
Setting a hotplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Chef's recommendations . . . . . . . . . . . . . . . . . . . . . . 16
Manual hood control . . . . . . . . . . . . . . . . . . . . . . . . . 18
Intensive setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Automatic start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Automatic mode with sensor control . . . . . . . . . . . . . 18
Run-on function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
| Flex Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Advice on using cookware . . . . . . . . . . . . . . . . . . . . . 19
As two independent hotplates . . . . . . . . . . . . . . . . . . 19
As a single hotplate . . . . . . . . . . . . . . . . . . . . . . . . . . 19
u Move function. . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
O Time-setting options . . . . . . . . . . . . . . . . . . . . . 21
Programming the cooking time . . . . . . . . . . . . . . . . .21
The kitchen timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Stopwatch function . . . . . . . . . . . . . . . . . . . . . . . . . . .22
v PowerBoost function . . . . . . . . . . . . . . . . . . . . . 22
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
x ShortBoost function . . . . . . . . . . . . . . . . . . . . . 23
Recommendations for use . . . . . . . . . . . . . . . . . . . . .23
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
z Keep warm function. . . . . . . . . . . . . . . . . . . . . . 23
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
s Transferring settings . . . . . . . . . . . . . . . . . . . . . 24
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Ü Cooking assist functions . . . . . . . . . . . . . . . . . 25
Cooking assistant function types . . . . . . . . . . . . . . . .25
Suitable cookware . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Sensors and special accessories . . . . . . . . . . . . . . . .26
Functions and heat settings . . . . . . . . . . . . . . . . . . . .26
Recommended dishes . . . . . . . . . . . . . . . . . . . . . . . .30
Teppan Yaki and Grill for the Flex Zone . . . . . . . . . .38
‚ Wireless temperature sensor . . . . . . . . . . . . . . 40
Preparing and maintaining the wireless temperature
sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Connecting the wireless temperature sensor to the
control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Changing the battery . . . . . . . . . . . . . . . . . . . . . . . . .41
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . .42
A Childproof lock. . . . . . . . . . . . . . . . . . . . . . . . . . 42
Activating and deactivating the childproof lock . . . . .42
Childproof lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
k Wipe protection . . . . . . . . . . . . . . . . . . . . . . . . . 43
b Automatic safety cut-out . . . . . . . . . . . . . . . . . . 43
Q Basic settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 44
To access the basic settings: . . . . . . . . . . . . . . . . . . .46
en
4
[ Energy consumption indicator . . . . . . . . . . . . . 46
t Cookware check. . . . . . . . . . . . . . . . . . . . . . . . . 47
h Power manager . . . . . . . . . . . . . . . . . . . . . . . . . 47
o Home Connect . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Home Connect settings . . . . . . . . . . . . . . . . . . . . . . . 49
Software update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Remote diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . .51
About data protection. . . . . . . . . . . . . . . . . . . . . . . . . 52
Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . 52
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Components to clean . . . . . . . . . . . . . . . . . . . . . . . . .53
Hob surround (only on appliances with hob surrounds)
53
Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Ventilation system . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Cleaning the overflow container . . . . . . . . . . . . . . . . . 55
{ Frequently Asked Questions (FAQ) . . . . . . . . . 56
3 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . 58
4 Customer service. . . . . . . . . . . . . . . . . . . . . . . . 60
Product number (E no.) and production number (FD
no.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
E Test dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.bosch-home.com and in the online shop
www.bosch-eshop.com
en
4
[ Energy consumption indicator . . . . . . . . . . . . . 46
t Cookware check. . . . . . . . . . . . . . . . . . . . . . . . . 47
h Power manager . . . . . . . . . . . . . . . . . . . . . . . . . 47
o Home Connect . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Setting up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Home Connect settings . . . . . . . . . . . . . . . . . . . . . . . 49
Software update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Remote diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . .51
About data protection. . . . . . . . . . . . . . . . . . . . . . . . . 52
Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . 52
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Cleaning agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Components to clean . . . . . . . . . . . . . . . . . . . . . . . . .53
Hob surround (only on appliances with hob surrounds)
53
Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Ventilation system . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Cleaning the overflow container . . . . . . . . . . . . . . . . . 55
{ Frequently Asked Questions (FAQ) . . . . . . . . . 56
3 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . 58
4 Customer service. . . . . . . . . . . . . . . . . . . . . . . . 60
Product number (E no.) and production number (FD
no.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
E Test dishes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.bosch-home.com and in the online shop
www.bosch-eshop.com
Intended use en
5
8Intended use
I nt ended us e
Read these instructions carefully. Please keep
the instruction and installation manual, as well
as the appliance certificate, in a safe place for
later use or for subsequent owners.
Check the appliance after removing it from the
packaging. If it has suffered any damage in
transport, do not connect the appliance,
contact the Technical Assistance Service and
provide written notification of the damage
caused, otherwise you will lose your right to
any type of compensation.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
This appliance must be installed according to
the installation instructions included.
This appliance is intended for private domestic
use and the household environment only. The
appliance must only be used for the
preparation of food and beverages. The
cooking process must be supervised. A short
cooking process must be supervised without
interruption. Only use the appliance in
enclosed spaces.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
Do not use covers. These can cause
accidents, for example due to overheating,
catching fire or materials shattering.
Only use safety devices or child protection
grilles approved by ourselves. Unsuitable
safety devices or child protection grilles may
result in accidents.
This appliance is not intended for operation
with an external clock timer or a remote
control.
Dangerous or explosive materials and vapours
must not be extracted.
Ensure that no small parts or liquids get into
the appliance.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 15 years old and are
being supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
When using the cooking functions, set the
hotplate on which you have placed the
saucepan with the temperature sensor.
If you wear an active implantable medical
device (e.g. a pacemaker or defibrillator),
check with your doctor that it complies with
Council Directive 90/385/EEC of 20th June
1990, DIN EN 45502-2-1 and DIN EN 45502-
2-2, and that it has been chosen, implanted
and programmed in accordance with VDE-AR-
E 2750-10. If these conditions are satisfied,
and if, in addition, non-metal cooking utensils
and cookware with non-metal handles are
used, it is safe to use this induction hob as
intended.
en Important safety information
6
(Important safety
information
Impor t ant s af et y i nf or mat i on
:Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
:Warning – Danger of death!
Risk of poisoning from flue gases being drawn
back in.
Always ensure that there is an adequate
supply of fresh air to the room if the appliance
is being operated in air extraction mode at the
same time as a non-room-sealed heating
appliance is being operated.
Non-room-sealed heating appliances (e.g.
gas-, oil-, wood- or coal-burning heaters,
continuous flow heaters or water heaters)
draw in combustion air from the room in which
they are installed and discharge the exhaust
gases outdoors through an exhaust gas
system (e.g. a chimney).
With the extractor hood switched on, air is
extracted from the kitchen and the adjacent
rooms – without an adequate supply of air, the
air pressure falls below atmospheric pressure.
Toxic gases from the chimney or the
extraction shaft are sucked backed into the
living space.
■ There must therefore always be an
adequate supply of air.
■ A supply-air/air-extraction duct alone is not
sufficient to ensure compliance with the
limit.
It is only possible to safely operate the
appliance if the pressure in the room in which
the heating appliance is installed does not
drop more than 4 Pa (0.04 mbar) below
atmospheric pressure. This can be achieved if
the air needed for combustion is able to enter
through openings that cannot be sealed, for
example through doors, windows, by means of
a supply-air/air-extraction duct or by other
technical means.
The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into
a shaft that is used to ventilate rooms in which
heating appliances are installed.
If the exhaust air is to be conveyed into a non-
functioning smoke or exhaust gas flue, you
must obtain the consent of the heating
engineer responsible.
Always consult the heating engineer
responsible. They will be able to assess the
house's entire ventilation setup and suggest
the most appropriate ventilation measures.
Unrestricted operation is possible if the
extractor hood is operated exclusively in air
recirculation mode.
:Warning – Risk of fire!
■ Hot oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk of fire!
■ The hotplates become very hot. Never
place combustible items on the hob. Never
place objects on the hob.
Risk of fire!
■ The appliance gets hot. Do not keep
combustible objects or aerosol cans in
drawers directly underneath the hob.
Risk of fire!
■ The hob switches off automatically and can
no longer be operated. It may switch on
unintentionally at a later point. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Risk of fire!
■ Fatty deposits in the grease filter may catch
fire. Regularly clean the grease filter. Never
operate the appliance without a grease
filter.
Risk of fire!
■ When the ventilation system is switched on,
fatty deposits in the grease filter may catch
fire. Never work with naked flames close to
the appliance (e.g. flambéing). Do not install
the appliance near a solid fuel heating
appliance (e.g. wood- or coal-burning)
unless a sealed, non-removable cover is
fitted. There must be no flying sparks.
en Important safety information
6
(Important safety
information
Impor t ant s af et y i nf or mat i on
:Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
:Warning – Danger of death!
Risk of poisoning from flue gases being drawn
back in.
Always ensure that there is an adequate
supply of fresh air to the room if the appliance
is being operated in air extraction mode at the
same time as a non-room-sealed heating
appliance is being operated.
Non-room-sealed heating appliances (e.g.
gas-, oil-, wood- or coal-burning heaters,
continuous flow heaters or water heaters)
draw in combustion air from the room in which
they are installed and discharge the exhaust
gases outdoors through an exhaust gas
system (e.g. a chimney).
With the extractor hood switched on, air is
extracted from the kitchen and the adjacent
rooms – without an adequate supply of air, the
air pressure falls below atmospheric pressure.
Toxic gases from the chimney or the
extraction shaft are sucked backed into the
living space.
■ There must therefore always be an
adequate supply of air.
■ A supply-air/air-extraction duct alone is not
sufficient to ensure compliance with the
limit.
It is only possible to safely operate the
appliance if the pressure in the room in which
the heating appliance is installed does not
drop more than 4 Pa (0.04 mbar) below
atmospheric pressure. This can be achieved if
the air needed for combustion is able to enter
through openings that cannot be sealed, for
example through doors, windows, by means of
a supply-air/air-extraction duct or by other
technical means.
The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into
a shaft that is used to ventilate rooms in which
heating appliances are installed.
If the exhaust air is to be conveyed into a non-
functioning smoke or exhaust gas flue, you
must obtain the consent of the heating
engineer responsible.
Always consult the heating engineer
responsible. They will be able to assess the
house's entire ventilation setup and suggest
the most appropriate ventilation measures.
Unrestricted operation is possible if the
extractor hood is operated exclusively in air
recirculation mode.
:Warning – Risk of fire!
■ Hot oil and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk of fire!
■ The hotplates become very hot. Never
place combustible items on the hob. Never
place objects on the hob.
Risk of fire!
■ The appliance gets hot. Do not keep
combustible objects or aerosol cans in
drawers directly underneath the hob.
Risk of fire!
■ The hob switches off automatically and can
no longer be operated. It may switch on
unintentionally at a later point. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Risk of fire!
■ Fatty deposits in the grease filter may catch
fire. Regularly clean the grease filter. Never
operate the appliance without a grease
filter.
Risk of fire!
■ When the ventilation system is switched on,
fatty deposits in the grease filter may catch
fire. Never work with naked flames close to
the appliance (e.g. flambéing). Do not install
the appliance near a solid fuel heating
appliance (e.g. wood- or coal-burning)
unless a sealed, non-removable cover is
fitted. There must be no flying sparks.
Important safety information en
7
:Warning – Risk of burns!
■ The hotplates and surrounding area
(particularly the hob surround, if fitted)
become very hot. Never touch the hot
surfaces. Keep children at a safe distance.
Risk of burns!
■ The hotplate heats up but the display does
not work. Switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
Risk of burns!
■ Metal objects on the hob quickly become
very hot. Never place metal objects (such
as knives, forks, spoons and lids) on the
hob.
Risk of fire!!
■ After each use, always turn off the hob at
the main switch. Do not wait until the hob
turns off automatically after the pan is
removed.
Risk of burns!
■ The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk of burns!
■ The appliance becomes hot during
operation. If hot liquids penetrate the
appliance, leave the appliance to cool
before removing the metal grease filter or
the overflow container.
:Warning – Risk of electric shock!
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the after-
sales service.
Risk of electric shock!
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk of electric shock!
■ Cracks or fractures in the glass ceramic
may cause electric shocks. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
:Warning – Hazard due to magnetism!
The wireless temperature sensor is magnetic.
The magnetic elements in it may damage
electronic implants, e.g. pacemakers or insulin
pumps. People fitted with electronic implants
should therefore not carry the temperature
sensor in their pockets and always keep it at
least 10 cm away from their pacemaker or
similar medical device.
:Warning – Risk of injury!
■ The wireless cooking sensor is equipped
with a battery, which may become
damaged if it is exposed to high
temperatures. Remove the sensor from the
cookware and store it away from any heat
sources.
Risk of injury!
■ The temperature sensor may be very hot
when removing it from the saucepan. Wear
oven gloves or use a tea towel to remove it.
Risk of injury!
■ When cooking in a bain marie, the hob and
cooking container could shatter due to
overheating. The cooking container in the
bain marie must not directly touch the
bottom of the water-filled pot. Only use heat-
resistant cookware.
Risk of injury!
■ Saucepans may suddenly jump due to
liquid between the pan base and the
hotplate. Always keep the hotplate and
saucepan bases dry.
en Causes of damage
8
]Causes of damage
Caus es of damage
Caution!
■ Rough pan bases may scratch the hob.
■ Objects that are hard or sharp may damage the hob.
Do not allow hard or sharp objects to fall on the hob.
■ Heating cookware when empty may cause surface
damage. Never leave empty cookware on the heat.
■ Do not place hot pans on the control panel, the
indicator area, or the hob frame. Doing so may
cause damage.
■ Never leave aluminium foil or plastic containers on
hot hotplates as this may damage the hob. No not
use oven liners.
■ Using unsuitable cleaning products may cause
surface damage, discolouration and stains. Only use
cleaning products that are suitable for this type of
hob.
■ Friction from pots and pans may cause surface
damage and discolouration. Always lift pots and
pans up before repositioning them; do not slide
them across the surface of the hob.
■ Burnt-on food may cause surface damage and
staining. Immediately remove any food that has
boiled over using a glass scraper.
■ Salt, sugar and sand may cause surface damage.
Do not use the hob as a work surface or storage
space.
■ Using cookware with a rough base may cause
surface damage. Check all cookware before use.
■ Sugar and foods with a high sugar content may
cause surface damage or conchoidal fracturing.
Immediately remove any food that has boiled over
using a glass scraper.
7Environmental protection
Envi r onment al pr ot ect i on
In this section, you can find information about saving
energy and disposing of the appliance.
Energy saving tips
■ Always use a matching lid for every item of
cookware. Cooking without a lid consumes
significantly more energy. Use a glass lid. Then you
can see into the pan without raising the lid.
■ Use cookware with a flat base. Uneven bases
increase the energy consumption.
■ Make sure that the diameter of the cookware base
corresponds to the size of the cooking zone. Please
note: Cookware manufacturers often specify the
diameter of the top of the pan, which is usually larger
than the diameter of the base of the pan.
■ For small quantities, use small items of cookware.
Using cookware that is large but barely filled
requires a lot of energy.
■ Cook with as little water as possible. This saves
energy and preserves the vitamins and minerals in
vegetables.
■ Switch to a lower heat setting in good time. This
prevents energy from being wasted.
■ During cooking, ensure that there is a sufficient
supply of air to enable the ventilation system to work
efficiently and with a low level of operating noise.
■ Adjust the fan speed to the amount of cooking
vapour produced during cooking.Only use the
intensive setting if needed. A lower fan speed
consumes less energy.
■ If cooking produces large amounts of vapour, select
a higher fan speed in good time. If the cooking
vapour has already spread around the kitchen, the
ventilation system will need to be operated for
longer.
■ Switch the appliance off when you are not using it.
■ Clean and (if required) replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
The wireless temperature sensor is battery-powered.
Dispose of used batteries in an environmentally
responsible manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
en Causes of damage
8
]Causes of damage
Caus es of damage
Caution!
■ Rough pan bases may scratch the hob.
■ Objects that are hard or sharp may damage the hob.
Do not allow hard or sharp objects to fall on the hob.
■ Heating cookware when empty may cause surface
damage. Never leave empty cookware on the heat.
■ Do not place hot pans on the control panel, the
indicator area, or the hob frame. Doing so may
cause damage.
■ Never leave aluminium foil or plastic containers on
hot hotplates as this may damage the hob. No not
use oven liners.
■ Using unsuitable cleaning products may cause
surface damage, discolouration and stains. Only use
cleaning products that are suitable for this type of
hob.
■ Friction from pots and pans may cause surface
damage and discolouration. Always lift pots and
pans up before repositioning them; do not slide
them across the surface of the hob.
■ Burnt-on food may cause surface damage and
staining. Immediately remove any food that has
boiled over using a glass scraper.
■ Salt, sugar and sand may cause surface damage.
Do not use the hob as a work surface or storage
space.
■ Using cookware with a rough base may cause
surface damage. Check all cookware before use.
■ Sugar and foods with a high sugar content may
cause surface damage or conchoidal fracturing.
Immediately remove any food that has boiled over
using a glass scraper.
7Environmental protection
Envi r onment al pr ot ect i on
In this section, you can find information about saving
energy and disposing of the appliance.
Energy saving tips
■ Always use a matching lid for every item of
cookware. Cooking without a lid consumes
significantly more energy. Use a glass lid. Then you
can see into the pan without raising the lid.
■ Use cookware with a flat base. Uneven bases
increase the energy consumption.
■ Make sure that the diameter of the cookware base
corresponds to the size of the cooking zone. Please
note: Cookware manufacturers often specify the
diameter of the top of the pan, which is usually larger
than the diameter of the base of the pan.
■ For small quantities, use small items of cookware.
Using cookware that is large but barely filled
requires a lot of energy.
■ Cook with as little water as possible. This saves
energy and preserves the vitamins and minerals in
vegetables.
■ Switch to a lower heat setting in good time. This
prevents energy from being wasted.
■ During cooking, ensure that there is a sufficient
supply of air to enable the ventilation system to work
efficiently and with a low level of operating noise.
■ Adjust the fan speed to the amount of cooking
vapour produced during cooking.Only use the
intensive setting if needed. A lower fan speed
consumes less energy.
■ If cooking produces large amounts of vapour, select
a higher fan speed in good time. If the cooking
vapour has already spread around the kitchen, the
ventilation system will need to be operated for
longer.
■ Switch the appliance off when you are not using it.
■ Clean and (if required) replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
The wireless temperature sensor is battery-powered.
Dispose of used batteries in an environmentally
responsible manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment -
WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Induction cooking en
9
fInduction cooking
I nduct i on cook i ng
Advantages of induction cooking
Induction cooking is very different from traditional
cooking methods, as heat builds up directly in the item
of cookware. This offers numerous advantages:
■ Saves time when boiling and frying.
■ Saves energy.
■ Easier to care for and clean. Spilled food does not
burn on as quickly.
■ Heat control and safety – the hob increases or
decreases the heat supply as soon as the user
changes the setting. The induction hotplate stops the
heat supply as soon as the cookware is removed
from the hotplate, without having to switch it off first.
Cookware
Only use ferromagnetic cookware for induction cooking,
such as:
■ Cookware made from enamelled steel
■ Cookware made from cast iron
■ Special induction-compatible cookware made from
stainless steel.
To check whether your cookware is suitable for
induction cooking, refer to the section on
~ "Cookware check".
To achieve a good cooking result, the ferromagnetic
area on the base of the pan should match the size of
the hotplate. If a hotplate does not detect an item of
cookware, try placing it on another hotplate with a
smaller diameter.
If the only hotplate being used is the flexible cooking
zone, larger cookware that is particularly suited to this
zone can be used. You can find information on
positioning cookware in the section on ~ "Flex Zone".
Some induction cookware does not have a fully
ferromagnetic base:
■ If the base of the cookware is only partially
ferromagnetic, only the area that is ferromagnetic will
heat up. This may mean that heat will not be
distributed evenly. The non-ferromagnetic area may
not heat up to a sufficient temperature for cooking.
■ The ferromagnetic area will also be reduced if the
material from which the base of the cookware is
made contains aluminium, for example. This may
mean that the cookware will not become sufficiently
hot or even that it will not be detected.
Unsuitable pans
Never use diffuser hobs or pans made from:
■ common thin steel
■ glass
■ earthenware
■ copper
■ aluminium
Properties of the base of the cookware
The material(s) from which the base of the cookware is
made can affect the cooking result. Using pots and
pans made from materials that distribute heat evenly
through them, such as stainless-steel pans with a three-
layer base, saves time and energy.
Use cookware with a flat base; if the base of the
cookware is uneven, this may impair the heat supply.
Absence of pan or unsuitable size
If no pan is placed on the selected hotplate, or if it is
made of unsuitable material or is not the correct size,
the power level displayed on the hotplate indicator will
flash. Place a suitable pan on the hotplate to stop the
flashing. If this takes more than 90 seconds, the
hotplate will switch off automatically.
Empty pans or those with a thin base
Do not heat empty pans, nor use pans with a thin base.
The hob is equipped with an internal safety system.
However, an empty pan may heat up so quickly that the
"automatic switch off" function may not have time to
react and the pan may reach very high temperatures.
The base of the pan could melt and damage the glass
on the hob. In this case, do not touch the pan and
switch the hotplate off. If it fails to work after it has
cooled down, please contact the Technical Assistance
Service.
FP
FP
FP
en Induction cooking
10
Pan detection
Each hotplate has a lower limit for pan detection. This
depends on the diameter of the ferromagnetic area of
the cookware and the material from which its base is
made. For this reason, you should always use the
hotplate that best matches the diameter of the base of
the pan.
en Induction cooking
10
Pan detection
Each hotplate has a lower limit for pan detection. This
depends on the diameter of the ferromagnetic area of
the cookware and the material from which its base is
made. For this reason, you should always use the
hotplate that best matches the diameter of the base of
the pan.
Getting to know your appliance en
11
*Getting to know your
appliance
Get t i ng to know your appl i anc e
You can find information on the dimensions and power
of the hotplates in~ Page 2
Note: . Depending on the appliance model, individual
details and colours may differ.
Your new appliance
Special accessories
Depending on the appliance model, various
accessories are available and you can obtain these
from specialist retailers, from our after-sales service or
from our official website:
■ Air extraction set
■ Air recirculation set
■ Activated charcoal filter: For air circulation
■ Acoustics filter: For air extraction mode
No. Designation
1 Metal grease filter
2 Activated charcoal filter for air recirculation or acoustics fil-
ter for air extraction*
3 Hob
4 Control panel
5 Overflow container
*Depending on the appliance specifications
#
+
en Getting to know your appliance
12
The control panel
Controls
When the hob heats up, the symbols for the controls
available at this time light up.
Touching a symbol activates the respective function.
Notes
■ The corresponding symbols for the controls light up
depending on whether they are available.
The displays for the hotplates or the selected
functions get brighter.
■ Always keep the control panel clean and dry.
Moisture can prevent it from working properly.
■ Do not place any cookware near the indicators or
sensors. The electronics could overheat.
Z
Selection sensors
#
Main switch
ã
Selecting the cooking zone
0 1Ê2Ê...Ê8Ê9
Settings area
á
PowerBoost and ShortBoost functions
Intensive ventilation settings
>
Locking the control panel for cleaning
Š
Childproof lock
Û
Keep-warm function
é
Frying sensor
è
FlexZone
ç
Move function
t
Timer
y
Cooking timer
x
Stopwatch function
D
Wi-Fi
:
Manual hood control
w
Sensor hood control
Display
‹.‹
Operating status
‚-Š
Power levels
•/œ
Residual heat
‹‹
Time-setting options
‹‹‹ ºC
Temperature for cooking functions
>
Locking the control panel for cleaning
Š
Childproof lock
y
Cooking timer
ö/ô
Timer displays
›.
PowerBoost function
˜›.
ShortBoost function
å
Cooking functions
é
Frying sensor
£
Transferring settings
–©
Keep-warm function
D
Wi-Fi
en Getting to know your appliance
12
The control panel
Controls
When the hob heats up, the symbols for the controls
available at this time light up.
Touching a symbol activates the respective function.
Notes
■ The corresponding symbols for the controls light up
depending on whether they are available.
The displays for the hotplates or the selected
functions get brighter.
■ Always keep the control panel clean and dry.
Moisture can prevent it from working properly.
■ Do not place any cookware near the indicators or
sensors. The electronics could overheat.
Z
Selection sensors
#
Main switch
ã
Selecting the cooking zone
0 1Ê2Ê...Ê8Ê9
Settings area
á
PowerBoost and ShortBoost functions
Intensive ventilation settings
>
Locking the control panel for cleaning
Š
Childproof lock
Û
Keep-warm function
é
Frying sensor
è
FlexZone
ç
Move function
t
Timer
y
Cooking timer
x
Stopwatch function
D
Wi-Fi
:
Manual hood control
w
Sensor hood control
Display
‹.‹
Operating status
‚-Š
Power levels
•/œ
Residual heat
‹‹
Time-setting options
‹‹‹ ºC
Temperature for cooking functions
>
Locking the control panel for cleaning
Š
Childproof lock
y
Cooking timer
ö/ô
Timer displays
›.
PowerBoost function
˜›.
ShortBoost function
å
Cooking functions
é
Frying sensor
£
Transferring settings
–©
Keep-warm function
D
Wi-Fi
Getting to know your appliance en
13
The hotplates
Residual heat indicator
The hob has a residual heat indicator for each hotplate.
This indicates that a hotplate is still hot. Do not touch a
hotplate while the residual heat indicator is lit up.
The following indicators are shown depending on the
amount of residual heat:
■ Display •: High temperature
■ Display œ: Low temperature
If you remove the cookware from the hotplate during
cooking, the residual heat indicator and the selected
heat setting will flash alternately.
When the hotplate is switched off, the residual heat
indicator will light up. Even after the hob has been
switched off, the residual heat indicator will stay lit for as
long as the hotplate is still warm.
Hotplate
Û
Simple hotplate Use cookware that is a suitable size
á
Flexible cooking zone See section ~ "Flex Zone"
Only use cookware that is suitable for induction cooking; see section ~ "Induction cooking"
en Operating modes
14
ÇOperating modes
Oper at i ng modes
This appliance can be used in air extraction mode or
circulating-air mode.
Exhaust air mode
Note: The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into a shaft
which is used to ventilate installation rooms which
contain heat-producing appliances.
■ Before conveying the exhaust air into a non-
functioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
■ If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Air recirculation
Note: To bind odours in air recirculation, you must
install an activated carbon filter. The different options for
operating the appliance in air recirculation can be found
in the brochure. Alternatively, ask your dealer. The
required accessories are available from specialist
retailers, from after-sales service or from the Online
Shop.
KBefore using for the first
time
Bef or e usi ng f or t he f i r st time
Please read the following information before using the
appliance for the first time:
Clean the appliance and all accessory parts thoroughly.
Before you can use your new appliance, you must apply
certain settings.
Switch the hob on and off using the main switch
#.
Setting Home Connect
When you first switch on the appliance, you will be
prompted to set up your home network. The
D symbol
will be lit dimly for a few seconds on the display panel.
To begin setting up the connection, touch the
D sensor and proceed in accordance with the
information given in the section entitled ~ "Home
Connect".To exit initial set-up, touch any sensor.
Setting the operating mode
The appliance is supplied with a preset air recirculation
mode.
When the hob is installed with an air outlet to the
outside, you must configure the setting
™‚ˆ in this
mode. See section ~ "Basic settings".
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
The air that is drawn in is cleaned by the
grease filters and the activated carbon filter,
and conveyed back into the kitchen.
en Operating modes
14
ÇOperating modes
Oper at i ng modes
This appliance can be used in air extraction mode or
circulating-air mode.
Exhaust air mode
Note: The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into a shaft
which is used to ventilate installation rooms which
contain heat-producing appliances.
■ Before conveying the exhaust air into a non-
functioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
■ If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Air recirculation
Note: To bind odours in air recirculation, you must
install an activated carbon filter. The different options for
operating the appliance in air recirculation can be found
in the brochure. Alternatively, ask your dealer. The
required accessories are available from specialist
retailers, from after-sales service or from the Online
Shop.
KBefore using for the first
time
Bef or e usi ng f or t he f i r st time
Please read the following information before using the
appliance for the first time:
Clean the appliance and all accessory parts thoroughly.
Before you can use your new appliance, you must apply
certain settings.
Switch the hob on and off using the main switch
#.
Setting Home Connect
When you first switch on the appliance, you will be
prompted to set up your home network. The
D symbol
will be lit dimly for a few seconds on the display panel.
To begin setting up the connection, touch the
D sensor and proceed in accordance with the
information given in the section entitled ~ "Home
Connect".To exit initial set-up, touch any sensor.
Setting the operating mode
The appliance is supplied with a preset air recirculation
mode.
When the hob is installed with an air outlet to the
outside, you must configure the setting
™‚ˆ in this
mode. See section ~ "Basic settings".
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
The air that is drawn in is cleaned by the
grease filters and the activated carbon filter,
and conveyed back into the kitchen.
Operating the appliance en
15
1Operating the appliance
Oper at i ng t he appl i anc e
This chapter explains how to set a hotplate. The table
shows heat settings and cooking times for various
meals.
Tip: Switch on the ventilation system when you start
cooking and only switch it off a few minutes after you
have finished cooking. This is the most effective way to
remove the cooking vapours.
Note: Never operate the appliance without the metal
grease filter and the overflow container.
Switching the hob on and off
The main switch is used to switch the hob on and off.
To switch on: Touch the
# symbol. An audible signal
sounds. The symbols for the hotplates and the functions
available at this time light up. The ‹.‹ symbol lights up
next to the hotplates. The hob is ready to use.
To switch off: Touch the # symbol until the indicators
go out. The residual heat indicator remains lit until the
hotplates have cooled down sufficiently.
Notes
■ If the appliance has not been connected to your
home network or the connection has been broken,
network connection initial set-up will be activated
whenever you switch on the hob.
■ The hob will automatically switch itself off if the
cooking zones have been switched off for a few
seconds.
■ The settings are stored for 4 seconds after the hob
has been switched off. If you switch the hob back on
during this time, the hob will operate using the
stored settings.
Setting a hotplate
Set the required heat setting using the ò to ê symbols.
Heat setting ò = lowest setting.
Heat setting ê = highest setting.
Every heat setting has an intermediate setting. This is
marked in the control panel with the Ê symbol.
Notes
■ To protect the fragile parts of your appliance from
overheating and electrical overloading, the hob may
temporarily reduce the power.
■ In order to prevent the appliance from producing
excess noise, the hob may temporarily reduce the
power.
Selecting a hotplate and heat setting
The hob must be switched on.
1. Touch the ã symbol for the required hotplate.
The ‹.‹ display gets brighter.
2. Then select the required heat setting from the
settings range.
The heat setting is set.
Note: When you place a pot or pan on the Flex Zone,
the hob detects it and the hob is selected automatically.
You will find more information about the Flex Zone in
the section entitled ~ "Flex Zone".
Changing the heat setting
Select the hotplate and then set the required heat
setting in the control panel.
Switching off the hotplate
Select the hotplate and set it to ‹.‹ in the settings
range. The hotplate switches itself off and the residual
heat indicator appears.
Notes
■ If no pan has been placed on the hotplate, the
selected power level flashes. After a certain time has
elapsed, the hotplate switches off.
■ If a pan has been placed on the hotplate before
switching on the hob, it will be detected within
20 seconds of pressing the main switch and the
hotplate will be selected automatically. Once
detected, select the power level within the next
20 seconds or the hotplate will switch off.
If more than one pan is placed on the hob, only one
will be detected when switching it on.
en Operating the appliance
16
Chef's recommendations
Recommendations
■ When heating up puree, cream soups and thick
sauces, stir occasionally.
■ Set heat setting 8 to 9 for preheating.
■ When cooking with the lid on, turn the heat setting
down as soon as steam escapes between the lid
and the cookware. Steam does not need to escape
for a good cooking result.
■ After cooking, keep the lid on the cookware until you
serve the food.
■ To cook with the pressure cooker, observe the
manufacturer's instructions.
■ Do not cook food for too long, otherwise the
nutrients will be lost. The kitchen clock can be used
to set the optimum cooking time.
■ For a more healthy cooking result, smoking oil
should be avoided.
■ To brown food, fry small portions in succession.
■ Cookware may reach high temperatures while the
food is cooking. We recommend that you use oven
gloves.
■ You can find recommendations for energy-efficient
cooking in section ~ "Environmental protection"
Cooking table
The table shows which heat setting is suitable for each
type of food. The cooking time may vary depending on
the type, weight, thickness and quality of the food.
Heat setting Cooking time
(mins)
Melting
Chocolate coating 1 - 1.5 -
Butter, honey, gelatine 1 - 2 -
Heating and keeping warm
Stew, e.g. lentil stew 1.5 - 2 -
Milk* 1.5 - 2.5 -
Heating sausages in water* 3 - 4 -
Defrosting and heating
Spinach, frozen 3 - 4 15 - 25
Goulash, frozen 3 - 4 35 - 55
Poaching, simmering
Potato dumplings* 4.5 - 5.5 20 - 30
Fish* 4 - 5 10 - 15
White sauces, e.g. Béchamel sauce 1 - 2 3 - 6
Whisked sauces, e.g. sauce béarnaise, hollandaise 3 - 4 8 - 12
* Without lid
** Turn several times
*** Preheat to heat setting 8 - 8.5
en Operating the appliance
16
Chef's recommendations
Recommendations
■ When heating up puree, cream soups and thick
sauces, stir occasionally.
■ Set heat setting 8 to 9 for preheating.
■ When cooking with the lid on, turn the heat setting
down as soon as steam escapes between the lid
and the cookware. Steam does not need to escape
for a good cooking result.
■ After cooking, keep the lid on the cookware until you
serve the food.
■ To cook with the pressure cooker, observe the
manufacturer's instructions.
■ Do not cook food for too long, otherwise the
nutrients will be lost. The kitchen clock can be used
to set the optimum cooking time.
■ For a more healthy cooking result, smoking oil
should be avoided.
■ To brown food, fry small portions in succession.
■ Cookware may reach high temperatures while the
food is cooking. We recommend that you use oven
gloves.
■ You can find recommendations for energy-efficient
cooking in section ~ "Environmental protection"
Cooking table
The table shows which heat setting is suitable for each
type of food. The cooking time may vary depending on
the type, weight, thickness and quality of the food.
Heat setting Cooking time
(mins)
Melting
Chocolate coating 1 - 1.5 -
Butter, honey, gelatine 1 - 2 -
Heating and keeping warm
Stew, e.g. lentil stew 1.5 - 2 -
Milk* 1.5 - 2.5 -
Heating sausages in water* 3 - 4 -
Defrosting and heating
Spinach, frozen 3 - 4 15 - 25
Goulash, frozen 3 - 4 35 - 55
Poaching, simmering
Potato dumplings* 4.5 - 5.5 20 - 30
Fish* 4 - 5 10 - 15
White sauces, e.g. Béchamel sauce 1 - 2 3 - 6
Whisked sauces, e.g. sauce béarnaise, hollandaise 3 - 4 8 - 12
* Without lid
** Turn several times
*** Preheat to heat setting 8 - 8.5
Operating the appliance en
17
Boiling, steaming, braising
Rice (with double the volume of water) 2.5 - 3.5 15 - 30
Rice pudding*** 2 - 3 30 - 40
Unpeeled boiled potatoes 4.5 - 5.5 25 - 35
Boiled potatoes 4.5 - 5.5 15 - 30
Pasta, noodles* 6 - 7 6 - 10
Stew 3.5 - 4.5 120 - 180
Soups 3.5 - 4.5 15 - 60
Vegetables 2.5 - 3.5 10 - 20
Vegetables, frozen 3.5 - 4.5 7 - 20
Cooking in a pressure cooker 4.5 - 5.5 -
Braising
Roulades 4 - 5 50 - 65
Pot roast 4 - 5 60 - 100
Goulash*** 3 - 4 50 - 60
Roasting/frying with little oil*
Escalope, plain or breaded 6 - 7 6 - 10
Escalope, frozen 6 - 7 6 - 12
Chop, plain or breaded** 6 - 7 8 - 12
Steak (3 cm thick) 7 - 8 8 - 12
Poultry breast (2 cm thick)** 5 - 6 10 - 20
Poultry breast, frozen** 5 - 6 10 - 30
Rissoles (3 cm thick)** 4.5 - 5.5 20 - 30
Hamburgers (2 cm thick)** 6 - 7 10 - 20
Fish and fish fillet, plain 5 - 6 8 - 20
Fish and fish fillet, breaded 6 - 7 8 - 20
Fish, breaded and frozen, e.g. fish fingers 6 - 7 8 - 15
Scampi, prawns 7 - 8 4 - 10
Sautéeing fresh vegetables and mushrooms 7 - 8 10 - 20
Stir-fry, vegetables, meat cut in Asian-style strips 7 - 8 15 - 20
Stir fry, frozen 6 - 7 6 - 10
Pancakes (baked in succession) 6.5 - 7.5 -
Omelette (cooked in succession) 3.5 - 4.5 3 - 10
Fried eggs 5 - 6 3 - 6
Deep-fat frying* (150-200 g per portion in 1-2 l oil, deep-fat fried in portions)
Frozen products, e.g. chips, chicken nuggets 8 - 9 -
Croquettes, frozen 7 - 8 -
Meat, e.g. chicken portions 6 - 7 -
Fish, breaded or in beer batter 6 - 7 -
Vegetables, mushrooms, breaded or battered, tempura 6 - 7 -
Small baked items, e.g. doughnuts, fruit in batter 4 - 5 -
Heat setting Cooking time
(mins)
* Without lid
** Turn several times
*** Preheat to heat setting 8 - 8.5
en Operating the appliance
18
Manual hood control
You can control the ventilation setting manually.
Note: Using tall items of cookware may prevent the
extraction system from working at optimum power. The
extraction power can be improved by placing a lid on
the cookware at an angle.
Activation
1. Touch the : symbol.
The ventilation system starts at the preset power
level.
2. Within the next 10 seconds, select the required
power level in the settings area.
The power level that is selected is displayed in the
settings area.
3. Touch the : symbol to confirm the selected setting.
The ventilation system switched on.
Changing and switching off
Touch the : symbol and select the required power
level or set it to ‹ in the settings area.
Intensive setting
There are two intensive modes for the ventilation
system. If you activate the intensive settings, the
ventilation system works at maximum output for a short
time.
Activation
Touch the
: symbol and select the required intensive
setting.
■ Intensive setting I : Touch the á symbol. The line
above the symbol lights up. The intensive setting is
activated.
■ Intensive setting II: Touch the á symbol twice. The
line above the symbol flashes. The intensive setting
is activated.
Note: After eight minutes, the appliance automatically
switches back to fan setting Š.
Changing and switching off
Touch the
: symbol and select the required power
level or set it to ‹ in the settings area.
Automatic start
If you select a power level for a cooking zone, the
automatic start switches on.
The hob comes with sensor-controlled automatic start
as standard. You can find out how to change this
setting in section ~ "Basic settings".
Automatic start with sensor control
The air quality sensor registers the cooking vapours
automatically, selects the optimum power level, and the
line above the w symbol lights up.
Automatic start via power levels
The ventilation system switches on at a power level in
accordance with the respective power level for the
cooking zone.
Automatic mode with sensor control
The hob has an air quality sensor that automatically
registers the cooking vapours and switches on the
ventilation system.
If the automatic start is switched off or is set in
accordance with the power levels, you can switch on
operation with sensor control manually at any time.
Activation
Touch the
w symbol. The line above the symbol lights
up more brightly and the optimum power level is set
automatically with the help of the sensor.
Deactivating
Touch the w symbol. The line above the symbol goes
out. The sensor control is switched off.
Note: You can find out how to set the sensor sensitivity
in section ~ "Basic settings".
Run-on function
The run-on function allows the ventilation system to
continue operating for a few minutes after the hob has
been switched off. This removes any remaining cooking
vapours. The ventilation system then automatically
switches off.
The hob is supplied as standard with the run-on time
with a maximum switch-off time. You can find out how to
change this setting in section ~ "Basic settings".
Activation
The run-on time is possible depending on the
configured basic settings:
■ Via the control for the air quality sensor. The w
symbol lights up.
■ With a maximum switch-off time. The : symbol
lights up.
Note: The run-on function only switches on if at least
one cooking zone has been switched on for at least one
minute.
Deactivating
Manual
Touch the
: or w symbols. The run-on function is
switched off.
Automatic
The run-on function is switched off in the following
cases:
■ The run-on time has elapsed.
■ The appliance is switched on again.
■ The sensor ensures that the air quality is in order.
en Operating the appliance
18
Manual hood control
You can control the ventilation setting manually.
Note: Using tall items of cookware may prevent the
extraction system from working at optimum power. The
extraction power can be improved by placing a lid on
the cookware at an angle.
Activation
1. Touch the : symbol.
The ventilation system starts at the preset power
level.
2. Within the next 10 seconds, select the required
power level in the settings area.
The power level that is selected is displayed in the
settings area.
3. Touch the : symbol to confirm the selected setting.
The ventilation system switched on.
Changing and switching off
Touch the : symbol and select the required power
level or set it to ‹ in the settings area.
Intensive setting
There are two intensive modes for the ventilation
system. If you activate the intensive settings, the
ventilation system works at maximum output for a short
time.
Activation
Touch the
: symbol and select the required intensive
setting.
■ Intensive setting I : Touch the á symbol. The line
above the symbol lights up. The intensive setting is
activated.
■ Intensive setting II: Touch the á symbol twice. The
line above the symbol flashes. The intensive setting
is activated.
Note: After eight minutes, the appliance automatically
switches back to fan setting Š.
Changing and switching off
Touch the
: symbol and select the required power
level or set it to ‹ in the settings area.
Automatic start
If you select a power level for a cooking zone, the
automatic start switches on.
The hob comes with sensor-controlled automatic start
as standard. You can find out how to change this
setting in section ~ "Basic settings".
Automatic start with sensor control
The air quality sensor registers the cooking vapours
automatically, selects the optimum power level, and the
line above the w symbol lights up.
Automatic start via power levels
The ventilation system switches on at a power level in
accordance with the respective power level for the
cooking zone.
Automatic mode with sensor control
The hob has an air quality sensor that automatically
registers the cooking vapours and switches on the
ventilation system.
If the automatic start is switched off or is set in
accordance with the power levels, you can switch on
operation with sensor control manually at any time.
Activation
Touch the
w symbol. The line above the symbol lights
up more brightly and the optimum power level is set
automatically with the help of the sensor.
Deactivating
Touch the w symbol. The line above the symbol goes
out. The sensor control is switched off.
Note: You can find out how to set the sensor sensitivity
in section ~ "Basic settings".
Run-on function
The run-on function allows the ventilation system to
continue operating for a few minutes after the hob has
been switched off. This removes any remaining cooking
vapours. The ventilation system then automatically
switches off.
The hob is supplied as standard with the run-on time
with a maximum switch-off time. You can find out how to
change this setting in section ~ "Basic settings".
Activation
The run-on time is possible depending on the
configured basic settings:
■ Via the control for the air quality sensor. The w
symbol lights up.
■ With a maximum switch-off time. The : symbol
lights up.
Note: The run-on function only switches on if at least
one cooking zone has been switched on for at least one
minute.
Deactivating
Manual
Touch the
: or w symbols. The run-on function is
switched off.
Automatic
The run-on function is switched off in the following
cases:
■ The run-on time has elapsed.
■ The appliance is switched on again.
■ The sensor ensures that the air quality is in order.
Flex Zone en
19
|Flex Zone
Fl e x Zone
You can use each flex zone as a single hotplate or as
two independent hotplates, as required.
It consists of four inductors that work independently of
each other. If using the flexible cooking zone, only the
area that is covered by cookware is activated.
Advice on using cookware
To ensure that the cookware is detected and heat is
distributed evenly, correctly centre the cookware:
As two independent hotplates
The flexible cooking zone is used like two independent
hotplates.
Activating
See section ~ "Operating the appliance"
As a single hotplate
Using the entire cooking zone by connecting both
hotplates.
Connecting the two cooking zones
The cooking zones are automatically connected or
separated depending on where the pot or pan is
placed.
Connecting them manually:
1. Set the pot or pan down. Select one of the two
cooking zones in the Flex Zone and set the power
level.
2. Touch the è symbol. The indicator lights up.
The power level appears in the display for the
cooking zone.
The Flex Zone is activated.
Changing the heat setting
Select one of the two hotplates in the flexible cooking
zone and change the heat setting in the settings range.
Adding a new item of cookware
1. Place the new pot or pan on the position that is
suitable for its size.
If the cookware has been set down correctly, the
appliance will detect it. The appliance separates the
zones and selects this automatically.
2. Select the power level you require from the settings
area.
Notes
■ If you move or lift the item of cookware on the active
cooking zone, the cooking zone will start searching
automatically and the power level you selected
previously will be retained.
■ You can switch off the automatic cookware detection
function. You will find more information about this in
the section entitled ~ "Basic settings".
Separating the two cooking zones
The cooking zones are automatically connected or
separated depending on where the pot or pan is
placed.
To separate the cooking zones manually, select one of
the two cooking zones in the Flex Zone and touch the
è symbol.
The Flex Zone is deactivated. The two cooking zones
will now operate independently of one another.
Notes
■ If the hob is switched off, and then switched back on
again later, the flexible cooking zone is reset to
function as two independent hotplates.
■ To change the configuration settings for the flexible
cooking zone, refer to section ~ "Basic settings".
As a single hotplate
Diameter smaller than or equal to 13 cm
Place the cookware on one of the four posi-
tions that can be seen in the illustration.
Diameter greater than 13 cm
Place the cookware on one of the three
positions that can be seen in the illustration.
If the cookware takes up more than one
hotplate, place it starting on the upper or
lower edge of the flexible cooking zone.
As two independent hotplates
The front and rear hotplates each have two induc-
tors and can be used independently of each other.
Select the required heat setting for each of the
hotplates. Use only one item of cookware on each
hotplate.
en Move function
20
uMove function
Move f unct i on
This function activates the entire flexible cooking zone,
which is divided into three cooking areas and which has
preset heat settings.
Only use one item of cookware. The size of the cooking
area depends on the cookware used and whether it is
positioned correctly.
This means that an item of cookware can be moved
during the cooking process to another cooking area
with another heat setting:
Preset heat settings:
Front area = heat setting
Š
Middle area = heat setting †
Rear area = heat setting ‚.†
The preset heat settings can be changed independently
of one another. You can find out how to change these in
the section on ~ "Basic settings".
Notes
■ If more than one item of cookware is detected on the
flexible cooking zone, the function is deactivated.
■ If the cookware is moved within the flexible cooking
zone or lifted up, the hob automatically starts
searching and the heat setting of the area in which
the vessel was detected is set.
■ You can find information on the size and positioning
of the cookware in the section on ~ "Flex Zone"
Activation
1. Select one of the two hotplates in the flexible
cooking zone.
2. Touch the ç symbol. The indicator beside the
ç symbol lights up. The flexible cooking zone is
activated as a single hotplate.
The heat setting in the area in which the cookware is
located lights up in the hotplate display.
The function has now been activated.
Changing the heat setting
The heat settings for the individual cooking areas can
be changed during the cooking process. Set the
cookware down on the cooking area and change the
heat setting in the settings range.
Notes
■ Only the heat setting in the area in which the
cookware is located is changed.
■ If the function is deactivated, the heat settings for the
three cooking areas are reset to the preset values.
Deactivating
Touch the ç symbol. The indicator beside the
ç symbol goes out.
The function was deactivated.
Note: If one of the cooking areas is set to
‹, the
function deactivates after a few seconds.
Cooking areas
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Bosch PXX895GA6(00) Istruzioni per l'uso
- Categoria
- Piani cottura
- Tipo
- Istruzioni per l'uso
in altre lingue
Documenti correlati
Altri documenti
-
Siemens EX875LX67E/02 Manuale utente
-
Siemens EX877LX67E Istruzioni per l'uso
-
ELICA LIEN DIAMOND 604 BL Manuale del proprietario
-
Haier HA2MTSJ58MB1 Manuale utente
-
Siemens EX901LVV1E Manuale utente
-
-
Siemens EX675LXV1E Manuale utente
-
-
-
Siemens iQ700 Manuale utente