HOTPOINT/ARISTON AQLF8F 292 U (EU) Guida utente

EN

1

English,1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Description of the machine, 4-5

Control panel

Auto Dose System, 6-7

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent

Preparing the laundry

Washing recommendations

Load balancing system

Precautions and advice, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 13-14

Assistance, 15

EN

WASHING MACHINE

AQUALTIS

AQLF8F 292 U

Instructions for

installation and use

Italiano,17

I

TR

Türkçe,49

CIS

Ðóññêèé,33

EN

2

Installation

 This instruction manual should be kept in a safe place

for future reference. If the washing machine is sold,

given away or moved, please ensure the manual is kept

with the machine, so that the new owner may benefit

from the advice contained within it.

 Read these instructions carefully: they contain vital

information relating to the safe installation and operation

of the appliance.

 Inside the pack containing this manual, you will also

find the guarantee and all the details necessary for

installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the

washing machine, make sure it has not been damaged

during transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4

protective screws (used

during transportation) and

the corresponding spacer,

located on the rear part of

the appliance (see figure).

3. Close off the holes using the plastic plugs supplied in

the pack.

4. Keep all the parts in a safe place; they will be

needed again if the washing machine is moved to

another location, to prevent the inside of the

appliance being damaged.

 Packaging materials should not be used as toys for

children.

Levelling

1. Place the washing machine on a flat sturdy floor,

without resting it up against walls or cabinets.

2. If the floor is uneven,

the front feet of the

machine may be adjusted

until it reaches a horizontal

position (the angle of

inclination must not

exceed 2 degrees).

 If the appliance is levelled correctly, it will be more

stable and much less likely to cause vibrations and noise

while it is operating, particularly during the spin cycle.

 If it is placed on carpet or a rug, adjust the feet in such

a way as to allow a sufficient ventilation space

underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

 Before connecting the inlet hose to the water supply,

run the water until it is perfectly clear.

1. Connect the inlet hose

to the machine by

screwing it onto the cold

water inlet of the

appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

2. Connect the inlet hose

by screwing it to a cold

water tab using a 3/4 gas

threaded connection (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical data table (see next

page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand or old inlet hoses; use the

products supplied with the machine.

EN

3

Technical data

Model

AQLF8F 292 U

Dimensions

width 59.5 cm

height 85 cm

depth 64,5 cm

Capacity

from 1 to 8 kg

Electrical

connections

please refer to the technical data

plate fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1200 rotations per minute

Energy rated

programmes

according to

regulation

EN 60456

programme ; temperature 60°C;

using a load of 8 kg.

This appliance conforms to the

following EC Directives:

- 2004/108/EC (Electromagnetic

Compatibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC

65 - 100 cm

Connecting the drain hose

Connect the drain hose to

drain duct piping or a wall

drain located between 65

and 100 cm above the

floor, making sure it is not

bent at all.

Alternatively, rest the drain

hose on the side of a

washbasin or bathtub,

fastening the duct

supplied to the tap (see

figure).

The free end of the hose

should not be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

 the socket is earthed and complies with all applicable

laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

appliance. If this is not the case, have the socket or

the plug replaced.

 The machine must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain, storms and other weather

conditions.

 The mains socket must remain within easy reach after

the washing machine has been installed.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable and plug must only be

replaced by authorised technicians.

Warning! The company shall not be held responsible in

the event that these regulations are not respected.

EN

4

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

Description of the machine

PORTHOLE DOOR

Always use the handle to

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside the

machine and can be

accessed by opening the

door.

Refer to the chapter "Auto

Dose System" for information

on operation.

Note: stick the label showing

the wash cycle descriptions

and options on the front of

the detergent dispenser drawer. You will find the sticker

in the pack containing this manual.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF

button briefly

and wait for the machine to start up again.

EN

5

TEMPERATURE button

WASH CYCLE

SELECTOR knob

DOOR LOCKED

indicator light

START/PAUSE

button with indicator

light

WASH

CYCLE

PHASE

icons

DELAY

TIMER

button

CHILD LOCK button

with indicator light

ON/OFF button with

indicator light

ECO indicator light

TEMPERATURE/

DETERGENT

display

SPIN display

DELAY TIMER/SOFTENER /

CYCLE DURATIONdisplay

Control panel

Button with  ON/OFF indicator light: press this briefly

to switch the machine on or off. The green indicator light

indicates that the machine is switched on. To switch off

the washing machine during the wash cycle, press and

hold the button for approximately 3 seconds; if the

button is pressed briefly or accidentally the machine will

not switch off. If the machine is switched off during a

wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in

either direction. To select the most suitable wash cycle,

please refer to the Table of wash cycles.

The knob will not move during the wash cycle.

TEMPERATURE

button: press to modify or exclude

the temperature setting; the value selected will appear

on the display above (see Running a wash cycle).

SPIN SPEED CYCLE

button: press to modify or

exclude the spin cycle; the value selected will appear on

the display above (see Running a wash cycle).

DELAY TIMER

button: press to set a DELAY TIMER

for the selected wash cycle; the set delay time will appear

on the display above (see Running a wash cycle).

DETERGENT and SOFTENER buttons: refer to

"Modifying pre-set parameters" in the chapter "Auto Dose

System".

DETERGENT DILUTION button: refer to "Filling the

tanks" in the chapter "Auto Dose System".

OPTION button with indicator light: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see Running a wash cycle).

WASH CYCLE PHASE icons: these illuminate to

indicate the progress of the wash cycle (Wash



Rinse

 Spin  Drain ).

The text

lights up when the cycle is complete.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the

indicator light will remain lit in a fixed manner. To pause

the wash cycle, press the button again; the indicator

light will flash in an orange colour. If the Door locked

indicator light is switched off, the door may be

opened. To start the wash cycle from the point at which

it was interrupted, press the button again.

DOOR LOCKED

indicator light: indicates that the

porthole door is locked. To open the door, pause the

wash cycle (see Running a wash cycle).

CHILD LOCK

button with indicator light: to activate

or deactivate the CHILD LOCK, press and hold the

button for approximately 2 seconds. when the indicator

light is illuminated, the control panel is locked. This

means it is possible to prevent wash cycles from being

modified accidentally, especially where there are children

in the home.

ECO indicator light: the

icon lights up when, after

altering the washing parameters, an energy saving of at

least 10% is made. Furthermore, before the machine

enters Standby mode, the icon will light up for a few

seconds; when the machine is switched off the

estimated energy saving will be around the 80% mark.

SPIN SPEED

button

OPTION button

with indicator light

DETERGENT

DILUTION

button

DETERGENT

button

SOFTENER

button

EN

6

Introduction

This washing machine is

equipped with two tanks: one

for liquid detergent (either

concentrated or diluted) with

a capacity of approx. 5.5 l

and another for liquid fabric

softener (either concentrated

or diluted) with a capacity of

approx. 3.5 l (see picture).

 Check the detergent/fabric

softener box to verify whether

it is diluted or concentrated

detergent. The automatic

dosing system intakes the

correct amount of detergent and fabric softener from the

tanks for each type of load and at the right time,

guaranteeing optimal washing results without wastage.

The amount of detergent/fabric softener can be modified

manually by pressing the DETERGENT and FABRIC

SOFTENER buttons (refer to "Modifying pre-set

parameters"). If you prefer, the washing machine can

also be used in the "traditional" mode, i.e. by adding the

detergent in the dispenser; the machine will automatically

detect the detergent and will not use the tanks.

Detergent dispenser

"Traditional" mode.

Pull out the detergent dispenser drawer up to the first

stop point to add the detergent (either liquid or powder

detergent), bleach or other additives (e.g. whiteners) and

the pre-wash detergent for washing in the "traditional"

mode (refer to "Traditional mode).

"Auto Dose System mode.

In order to fill the detergent

and fabric softener tanks,

the detergent dispenser

drawer must be fully

extracted: open the dispenser

drawer up to the first stop

point then press the lever (A)

and open up to the second

stop point, making sure that

it is fully extracted. Avoid

moving the dispenser drawer during filling operations.

Once the tanks have been filled (refer to "Filling the tanks"),

the machine can run up to 40 cycles before the detergent

finishes (*).

First-time use

Turn the washing machine on by pressing the ON/OFF

button. The first wash cycle must be carried out without

laundry and by adding detergent in the detergent

dispenser (refer to "Traditional mode); set the

programme "

" (Cotton 90°) without pre-wash and

without filling the tanks.

Filling the tanks:

Open the detergent dispenser drawer in the "Auto Dose

System" mode (refer to "Detergent dispenser").

Slowly pour the detergent (B) and fabric softener (C)

until the tanks are completely filled (see picture).

To avoid exceeding the maximum capacity, a buzzer

(beep) will sound with growing intensity to signal the level

and 3 long beeps will sound once the tank is completely

full.

Start the wash cycle immediately after filling the tanks to

ensure that the dispenser is properly cleaned.The

respective icons

(for the detergent) and (for the

fabric softener) will light up gradually to signal the level.

The filling time depends on the density of the product.

Very dense products will take longer to fill.

Close the detergent dispenser drawer only once the

compartments are completely empty.

Select the density of the detergent added (either

concentrated or liquid) by pressing the appropriate

button

.

The machine will store the selection.

If no option is selected, the detergent intake option will

be pre-set to "diluted".

Use button

to set the amount of fabric softener that

will be automatically extracted by the machine:

1) If concentrated softener is used, we recommend

selecting the first level (

with one bar) and, if

necessary, stepping up by a single position (

with 2

bars) to increase detergent intake.

2) If diluted softener is used, we recommend setting level

3 (

with 3 bars) and to then either increase/decrease

the amount of fabric softener to be extracted.

3) To exclude the use of fabric softener, press

until

the bars disappear (also refer to "Modifying pre-set

parameters").

A

B

C

Auto Dose System

(*) with an average load of 4 kg, 40°C Cotton programme, "medium" water

hardness level and dirt level set to 3.

EN

7

Signals for successive refilling:

When the level of detergent/fabric softener falls below the

required level, at the end of the cycle, the first segment of

the

detergent symbol or the petal of the fabric softener

symbol in the bottom left section, will flash slowly on the

display. Once the detergent/fabric softener is finished, the

first segment of the

detergent symbol or the petal of the

fabric softener symbol in the lower left section will flash

fast to signal that the detergent or fabric softener tank is

empty. While the cycle runs, with empty tanks, the

symbols will disappear; at the end of the cycle or during the

pause mode, the first segment of the symbol and the

petal of the

symbol in the lower left section will flash fast.

If the tanks are not filled, the successive wash cycles in

Auto Dose System will be carried out without any intake of

detergent.

 We suggest adding detergent and fabric softener ONLY

after the machine's signal.

 NEVER mix two different detergents; always clean out

the tank before adding a new type of detergent (refer to

"Cleaning cycle set by the user").

Using the "Auto Dose System"

If the compartments have been filled with detergent and

fabric softener, you may start using the machine (refer to

"Running a wash cycle").

Powder detergents for pre-washing and powder additives

may only be used in the traditional mode or using the "Auto

Dose System", by placing the additives directly inside the

drum, preferably in conjunction with the "laundry ball".

Modifying pre-set parameters:

The machine automatically intakes detergent on the

basis of the selected programme, wash load and water

hardness. However, the amount of detergent/fabric

softener used may be modified.

button: press to increase, decrease and to exclude

detergent intake.

button: press to increase, decrease and to exclude

fabric softener intake.

The level of detergent/fabric softener suggested by the

machine is indicated by 3 bars.

Less than 3 bars indicates a lower level of detergent/

fabric softener compared to that suggested by the

machine, while more than 3 bars indicates a higher level

of detergent/fabric softener.

Cleaning the tanks:

Tank cleaning cycles can either be automatic or pre-set

by the user.

Automatic cleaning:

The washing machine carries out an automatic cleaning

cycle during the rinse cycle if the level of detergent that

remains is insufficient for carrying out a

successive wash cycle.

Cleaning cycle set by the user:

Run the cleaning cycle (with empty drum) if you require

adding a different product to the previous one or if the tanks

have been incorrectly filled (e.g. fabric softener has been

erroneously poured into the detergent tank or vice-versa).

Press button

and hold for approximately 8 sec. to activate

cleaning of the detergent tank, button

for cleaning the

fabric softener tank or button

for cleaning both tanks.

Once the buzzers with growing intensity are followed by 2

long buzzers and the icons

for the detergent, for the

fabric softener,

for both tanks appear, the cleaning cycle

for the selected container will start.

The cleaning cycle lasts about 40' if the tanks are initially

empty; if not, the cycle will last longer.

During the tank cleaning cycle, the

symbol will fill

gradually from bottom to top and the

symbol will fill

gradually petal by petal.

"Traditional" mode

Pull out the detergent dispenser drawer up to the first

stop point (see picture) then pour the amount of

detergent and other additives (e.g. bleach) required for a

single wash cycle directly into the dispenser.

1. pre-wash compartment:

use powder detergent only.

2. main wash

compartment: use powder

or liquid detergent. If the

latter is used, we

recommend pouring it into

the dispenser immediately

before starting the washing

machine and without

running a pre-wash cycle.

3. ! Do not pour anything in this compartment.

Tablet detergent or the relative "laundry ball" must be

added directly inside the drum. In this event, deactivate

the "Auto Dose System" (by pressing the

button until

the relative vertical bars disappear from the display).

Do not pour any fabric softener as the appropriate

quantity required for each wash cycle will be

automatically extracted.

To deactivate fabric softener intake, press the

button

until the vertical bars disappear from the display.

For wool and silk garments, we recommend using a

special detergent which must be poured directly into the

detergent dispenser (compartment 2).

Running the wash cycle:

Select the programme and the compatible options on

the basis of the required need and type of load.

3

1

2

EN

8

Running a wash cycle

WARNING: before you use the washing machine for

the first time, run a wash cycle with detergent and no

laundry, using the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the

button.

All the indicator lights will illuminate for 1 second; the

indicator light corresponding to the

button will then

remain lit in a fixed manner and the START/PAUSE

indicator light will flash slowly.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

3. MEASURE OUT THE DETERGENT. There is no

need to add detergent when the "Auto Dose System"

mode is used, as the machine automatically intakes

detergent on the basis of the selected programme,

type of load and water hardness. Refer to the

paragraph "Traditional mode for implementing the

traditional operation mode.

4. CLOSE THE PORTHOLE DOOR.

5. SELECT THE PROGRAMME. Turn the WASH

CYCLE SELECTOR KNOB right or left, until you have

selected the desired wash cycle. A temperature and

spin speed is set for each wash cycle; these may be

adjusted.

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons on the control panel:

Modify the temperature and/or spin

speed.

The machine automatically displays the maximum

temperature and spin speed values set for the

selected cycle, or the most recently-used settings if

they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash ( ) setting is reached.

The spin speed may be progressively reduced by

pressing the

button, until it is completely excluded

(

). If these buttons are pressed again, the

maximum values are restored.

 Exception: if the Cotton programme is selected,

the temperature can be increased up to a value of

90°C.

Set a DELAY TIMER.

Press the button until you have reached the desired

delay time. During the setting process, the delay time

is shown on the display and the

symbol flashes.

After selecting a DELAY TIMER time, the fixed

symbol and the cycle duration will appear on the

display. Press the button once to display the selected

delay time. To remove the DELAY TIMER option,

press the button until the display shows the text OFF;

the

symbol will disappear.

 Once the START/PAUSE button has been pressed,

the time delay may only be decreased.

Modify the cycle settings.

Press the OPTION button to customise the wash

cycle in accordance with your own requirements.

 Press the button to activate the option; the

corresponding indicator light will switch on.

 Press the button again to disable the option; the

indicator light will switch off.

 If the selected option is not compatible with the

selected wash cycle, this incompatibility will be

signalled by the flashing of the indicator light and a

sound alert (3 beeps); the option will not be activated.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

remains lit in a fixed manner and the porthole door

locks (the

DOOR LOCKED indicator light

illuminates). The icons corresponding to the wash

cycle phases will light up during the cycle to indicate

which phase is currently in progress. To change a

wash cycle once it has already started, pause the

washing machine by pressing the START/PAUSE

button; then select the desired cycle and press the

START/PAUSE button again. To open the door during

a wash cycle, press the START/PAUSE button; if the

DOOR LOCKED

indicator light is switched off you

may open the door. Press the START/PAUSE button

again to restart the wash cycle from the point at

which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may

be opened immediately. If the START/PAUSE indicator

light is flashing, press the button to end the cycle.

Open the door, unload the laundry and switch off the

machine.

 If you wish to cancel a cycle which has already begun,

press and hold the

button until the cycle stops and

the machine switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to

wash even the most valuable and delicate garments in

complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you

wash quilts and padded items with an outer layer made

using synthetic material.

EN

9

Options

 Detergent dosage

To dose the amount of detergent (refer to the chapter

"Auto Dose System").

 Concentrated Detergent

To modify the degree of detergent density (refer to the

chapter "Auto Dose System").

 Fabric softener dosage

To dose the amount of fabric softener (refer to the

chapter "Auto Dose System").

Extra rinse

By selecting this option, the efficiency of the rinse is

increased and optimal residual detergent removal is

guaranteed. It is particularly useful for skin which is

sensitive to detergents. We recommend this option is

used with a full load of washing, or when a large amount

of detergent is required.

 It cannot be used in conjunction with

, , .

(*) The duration of the wash cycles can be checked

on the display.

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this

value will then be shown on the display.

Wash cycles and options

Table of wash cycles

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle

with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle

with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle

with a temperature of 40°C.

Icon Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergent and additives

Max.

load

(kg)

Cycle

duration

Detergent

for prewash

Detergent

for wash

Fabric

softener

Cottons wash cycles

Cotton with pre-wash

(Add detergent to the relevant compartment).

90° 1200

lll

8

Cotton (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1200 -

ll

8

Cotton (2): heavily soiled whites and delicate colours.

40° 1200 -

ll

8

Coloured Cotton (3) 40° 1200 -

ll

8

Shirts

40° 600 -

ll

2

Jeans

40° 800 -

ll

4

Special programmes

Baby: heavily soiled delicate colours

40° 800 -

ll

4

Durable Synthetics 60° 800 -

ll

4

Delicate

Synthetics

40° 800 -

ll

4

"Bed & Bath" for bedlinen and towels.

60° 1200 -

ll

8

Duvets:

for down-stuffed garments.

30° 1000 -

ll

3,5

Silk: for garments in silk and viscose, lingerie.

30° 0 -

ll

2

Wool: for wool, cashmere, etc.

40° 600 -

ll

2

Mix 30': to refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand)

30° 800 -

ll

3,5

Partials wash cycles

Rinse - 1200 - -

l

8

Spin - 1200 - - - 8

Drain - 0 - - - 8

EN

10

Detergents and laundry

Detergent

The type and quantity of detergent required depend on

the type of fabric you are washing (cotton, wool, silk,

etc.), as well as its colour, the washing temperature, the

level of soiling and the hardness of the water in the area.

Whenever the detergent and fabric softener Auto Dose

System is activated, this washing machine helps to

prevent wastage and to protect the environment,

besides guaranteeing optimal washing performance.

We recommend the following:

 Use powder detergent for carrying out a pre-wash

and pour in the "traditional" mode.

 Use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

 When activating the "Auto Dose System" mode, use

liquid detergent and fabric softeners only. Never add

ultra-concentrated detergents (e.g. "Gel" type

detergents or similar).

 Use gentle liquid detergents for wool and silk

garments and pour in the "traditional" mode.

 Never mix two different detergents; always clean out

the tank before adding a new type of detergent.

The detergent should be poured into the relevant

compartment - or the dispenser placed directly inside the

drum - before the wash cycle begins. In the latter case, it will

not be possible to select the Cottons with pre-wash cycle.

 Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

 Shake out the garments before loading them into the

machine.

 Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

 Empty all pockets and check the buttons;

 Do not exceed the values listed in the Table of wash

cycles, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

Shirts: use the special Shirts wash cycle to wash

shirts in different fabrics and colours to guarantee they

receive the best possible care.

Jeans: use the special Jeans

wash cycle for all

denim garments; turn inside out before washing and use

a liquid detergent.

Baby: use the special Baby

wash cycle to remove

the remove the soiling typically caused by babies, while

removing all traces of detergent from nappies in order to

prevent the delicate skin of babies from suffering allergic

reactions. The cycle has been designed to reduce the

amount of bacteria by using a greater quantity of water

and optimising the effect of special disinfecting additives

added to the detergent. At the end of the wash cycle,

the machine will slowly rotate the drum; to end the cycle

press the START/PAUSE button.

Silk: use the special Silk

wash cycle to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: use the Silk

wash cycle. These should

be folded and placed inside the bag provided.

Wool: is the only washing machine brand to have been

awarded the prestigious Woolmark Platinum Care

endorsement (M.0508) by the Woolmark Company,

which means that all woollen garments may be washed

in the washing machine, even those which state hand

wash only

on the label. The Wool wash cycle can

be used to wash all woollen garments in the washing

machine while guaranteeing optimum performance.

Duvets: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

special Duvets

wash cycle. We recommend that

duvets are placed in the drum with their edges folded

inwards (see figure) and that no more than ¾ of the total

volume of the drum is used.

Quilts: to wash quilts with a synthetic outer layer, use

the bag provided and set the wash cycle to Duvets

.

Bedlinen and towels: use the Bed & Bath

cycle

to wash laundry from all over the house; this optimises

fabric softener performance and helps you save time and

energy. We recommend the use of powder detergent.

Stubborn stains: it is wise to treat stubborn stains with

solid soap before washing, and to use the Cottons with

pre-wash cycle.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If

the load is excessively unbalanced, the washing

machine performs the distribution process instead of

spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

EN

11

Precautions and tips

 The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

 This appliance was designed for domestic use only.

 Do not touch the machine when barefoot or with wet

or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage the

safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 If it must be moved, proceed with the help of two or

three people and handle it with the utmost care.

Never try to do this alone, because the appliance is

very heavy.

 Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their

local authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it is

not, remove excess water

using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is

freed from its stop position;

pull downwards until you

hear a click, which

indicates that the door is

now unlocked.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

EN

12

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and

help to prevent leaks.

 Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

To pull out the dispenser drawer, open until the first stop

point then press lever A to open completely; finally, press

one of the levers D and pull the drawer outwards (see

picture).

Wash it under running water; this procedure should be

effected regularly. Be careful to remove any detergent

residues from the dispenser drawer socket on the

machine.

Keep the drawer to the left hand side when replacing it

to ensure that it centres the guides and to prevent it

from jamming.

Caring for your appliance drum

 Always leave the door ajar to prevent unpleasant

odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

protective pre-chamber at the base of the pump.

 Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. take off the cover panel on the front of the machine

by first pressing it in the centre and then pushing

downwards on both sides until you can remove it (see

figures);

2. position a container so

that it will collect the water

which flows out

(approximately 1.5 l) (see

figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

1

2

A

D

EN

13

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre

(see Assistance), make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water.

The machine continuously fills

with water and drains.

The washing machine does not

drain or spin.

The machine vibrates a lot during

the spin cycle.

The washing machine leaks.

The icons corresponding to the

Phase in progress flash rapidly

at the same time as the ON/OFF

indicator light.

There is too much foam.

The washing machine door

remains locked.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or not enough to make

contact.

 There is no power in the house.

 The door is not closed properly.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A DELAY TIMER has been set.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from the

floor (see Installation).

 The free end of the hose is under water (see Installation).

 If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washing machine to fill

with water and drain continuously. Special anti-draining valves are available

in shops and help to prevent this inconvenience.

 The wall drainage system is not fitted with a breather pipe.

 The wash cycle does not include draining: Some wash cycles require the

drain phase to be started manually (see Wash cycles and options).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The machine is not level (see Installation ).

 The machine is trapped between cabinets and walls (see Installation).

 The load is unbalanced (see Detergents and laundry).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser is blocked (to clean it, see Care and

maintenance).

 The drain hose is not fixed in place properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

 The detergent is not suitable for machine washing (it should display the text

for washing machines or hand and machine wash, or the like).

 Too much detergent was used.

 Perform the manual unlocking procedure (see Precautions and tips).

EN

14

Troubleshooting:

The machine's washing

performance is unsatisfactory.

What happens if the tanks are

loaded even if they are already full?

What happens if the dispenser is

used in the traditional mode while

the tanks are still full?

Can the tanks also be used for

powder detergent?

Can powder detergent fall into the

tanks?

What happens if the dispenser is

not opened properly when filling the

tanks?

What happens if detergent and

fabric softener are erroneously

inverted?

What happens if different

detergents are mixed before the

tanks are empty?

Possible causes / Solutions:

 The tanks have not been loaded correctly (e.g. fabric softener has been

added instead of detergent or vice-versa)

 Two different types of detergent/fabric softener have mixed.

 NEVER mix two different detergents; always clean out the tanks before adding

a new type of detergent.

 The "Auto Dose System is blocked due to prolonged lack of use: carry

out a tank cleaning cycle (refer to "Cleaning cycle pre-set by user").

 Buzzers (Beep) and visual signals (icons appearing on the display) indicate

that the tank is full. If further detergent/fabric softener is added, the excess

quantity will fall into the drum and will be washed away with the next cycle.

 The machine will automatically track whether powder or liquid detergent

has been loaded in the traditional mode and will not intake any amount of

detergent from the tank. Fabric softener can only be used in the "Auto

Dose System mode.

 No, powder detergent can only be used in the traditional mode.

 No, there is a barrier to prevent powder detergent from falling into one of

the tanks even if the dispenser is open in the "Auto Dose System" position

(i.e. completely open).

 If the dispenser is not completely open, the detergent or fabric softener

that has been added will fall into the drum and will be washed away with

the next cycle.

 The washing machine will wash with unsatisfactory results, the tanks will

have to be emptied and subjected to a manual cleaning cycle.

 The machine will wash normally although we recommend only refilling the

tanks after the signal emitted by the machine; do not mix different

detergents/fabric softeners.



Note: To exit Demo mode, press and hold the two ON/OFF and START/PAUSE buttons simultaneously for 3 seconds.

EN

15

Assistance

Before calling for Assistance:

 Check whether you can solve the problem by yourself (see Trouble shooting);

 Restart the wash cycle to check whether the problem has been solved;

 If it has not, contact the Authorised Technical Assistance Service.

 If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.

 Always request the assistance of authorised technicians.

Please have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

The above information can be found on the data plate located on the appliance itself.

EN

16

17

I

Italiano

Sommario

Installazione, 18-19

Disimballo e livellamento

Collegamenti idraulici ed elettrici

Dati tecnici

Descrizione della macchina, 20-21

Pannello comandi

Auto Dose System, 22-23

Come effettuare un ciclo di lavaggio, 24

Programmi e opzioni, 25

Tabella Programmi

Le opzioni di lavaggio

Detersivi e biancheria, 26

Detersivo

Preparare la biancheria

Consigli di lavaggio

Sistema bilanciamento del carico

Precauzioni e consigli, 27

Sicurezza generale

Smaltimento

Apertura manuale della porta oblò

Manutenzione e cura, 28

Escludere acqua e corrente elettrica

Pulire la macchina

Pulire il cassetto dei detersivi

Curare il cestello

Pulire la pompa

Controllare il tubo di alimentazione dellacqua

Anomalie e rimedi, 29

Assistenza, 30

Assistenza Attiva 7 giorni su 7

I

LAVABIANCHERIA

AQUALTIS

AQLF8F 292 U

Istruzioni per

linstallazione e luso

18

I

 E importante conservare questo libretto per poterlo

consultare in ogni momento. In caso di vendita, di

cessione o di trasloco, assicurarsi che resti insieme

alla lavabiancheria.

 Leggere attentamente le istruzioni: ci sono importanti

informazioni sullinstallazione, sulluso e sulla

sicurezza.

 Nella busta contenente questo libretto troverete,

oltre alla garanzia, dei particolari che serviranno per

linstallazione.

Disimballo e livellamento

Disimballo

1. Una volta disimballata la lavabiancheria, controllare

che non abbia subito danni durante il trasporto.

Se fosse danneggiata non collegarla e contattare

il rivenditore.

2. Rimuovere le 4 viti di

protezione per il

trasporto ed il relativo

distanziale posti nella

parte posteriore (vedi

figura).

3. Chiudere i fori con i tappi di plastica contenuti nella

busta.

4. Conservare tutti i pezzi; qualora la lavabiancheria

dovesse essere trasportata, dovranno essere

rimontati per evitare danneggiamenti interni.

 Gli imballaggi non sono giocattoli per bambini.

Livellamento

1. Posizionare la lavabiancheria su un pavimento

piano e rigido, senza appoggiarla a muri o mobili.

2. Compensare le

irregolarità svitando o

avvitando i piedini finchè

la macchina non sia

orizzontale (non deve

essere inclinata più di 2

gradi).

 Un accurato livellamento dà stabilità ed evita vibrazioni

e rumorosità soprattutto nella fase di centrifuga.

 In caso sia posizionata su moquette o tappeti,

regolare i piedini in modo da conservare sotto la

lavabiancheria lo spazio necessario per la ventilazione.

Collegamenti idraulici ed elettrici

Collegamento del tubo di alimentazione dellacqua

Prima di collegare il tubo di alimentazione alla rete

idrica, far scorrere l'acqua finché non sia limpida.

1. Collegare il tubo di

alimentazione alla

macchina avvitandolo

all'apposita presa

d'acqua, nella parte

posteriore in alto a

destra (vedi figura).

2. Collegare il tubo di

alimentazione

avvitandolo a un

rubinetto d'acqua fredda

con bocca filettata da

3/4 gas (vedi figura).

3. Fare attenzione che nel tubo non ci siano né pieghe

né strozzature.

 La pressione idrica del rubinetto deve essere

compresa nei valori della tabella Dati tecnici

(vedi pagina a fianco).

 Se la lunghezza del tubo di alimentazione non fosse

sufficiente, rivolgersi a un negozio specializzato o a un

tecnico autorizzato.

 Non utilizzare mai tubi di carico usati o vecchi, ma

quelli in dotazione alla macchina.

Installazione

19

I

Dati tecnici

Modello

AQLF8F 292 U

Dimensioni

larghezza cm 59,5

altezza cm 85

profondità cm 64,5

Capacità

da 1 a 8 kg

Collegamenti

elettrici

vedi la targhetta caratteristiche

tecniche applicata sulla macchina

Collegamenti

idrici

pressione massima 1 MPa (10 bar)

pressione minima 0,05 MPa (0,5 bar)

capacità del cesto 62 litri

Velocità di

centrifuga

sino a 1200 giri al minuto

Programmi di

controllo secondo

la norma EN 60456

programma ; temperatura 60°C;

effettuato con 8 kg di carico.

Questa apparecchiatura è conforme

alle seguenti Direttive Comunitarie:

- 2004/108/CE (Compatibilità

Elettromagnetica)

- 2002/96/CE

- 2006/95/CE (Bassa Tensione)

Collegamento del tubo di scarico

Collegare il tubo di

scarico a una conduttura

di scarico o a uno

scarico a muro posti tra

65 e 100 cm da terra

evitando assolutamente

di piegarlo.

In alternativa,

appoggiare il tubo di

scarico al bordo di un

lavandino o di una

vasca, legando la guida

in dotazione al rubinetto

(vedi figura).

L'estremità libera del

tubo di scarico non

deve rimanere immersa

nell'acqua.

 È sconsigliato usare tubi di prolunga; se

indispensabile, la prolunga deve avere lo stesso

diametro del tubo originale e non superare i 150 cm.

Collegamento elettrico

Prima di inserire la spina nella presa della corrente,

accertarsi che:

 la presa abbia la messa a terra e sia a norma

di legge;

 la presa sia in grado di sopportare il carico

massimo di potenza della macchina, indicato

nella targhetta caratteristiche;

 la tensione di alimentazione sia compresa nei

valori indicati nella targhetta caratteristiche;

 la presa sia compatibile con la spina della

macchina. In caso contrario far sostituire la presa o

la spina.

 La macchina non va installata all'aperto, nemmeno

se lo spazio è riparato, perché è molto pericoloso

lasciarla esposta a pioggia e temporali.

 A macchina installata, la presa della corrente deve

essere facilmente raggiungibile.

 Non usare prolunghe e multiple.

 Il cavo non deve subire piegature o compressioni.

 Il cavo di alimentazione e la spina devono essere

sostituiti solo da tecnici autorizzati.

Attenzione! Lazienda declina ogni responsabilità

qualora queste norme non vengano rispettate.

65 - 100 cm

20

I

Descrizione della macchina

PORTA OBLO

Per aprire la porta oblò

utilizzare sempre lapposita

maniglia

(vedi figura).

CASSETTO DETERSIVI

Il cassetto detersivi si

trova allinterno della

macchina e vi si accede

aprendo la porta.

Per lutilizzo vedi il capitolo

Auto Dose System.

Per il dosaggio dei detersi-

vi vedi il capitolo Detersivi

e biancheria.

Nota: attaccare sul

cassetto detersivi ladesivo con le descrizioni dei

programmi e opzioni. Ladesivo si trova nella busta

contenente questo libretto.

PANNELLO

COMANDI

PORTA OBLÒ

MANIGLIA

PORTA

OBLÒ

ZOCCOLO

PIEDINI REGOLABILI

Modalità di stand by

Questa lavatrice, in conformità alle nuove normative

legate al risparmio energetico, è dotata di un sistema

di autospegnimento (stand by) che entra in funzione

dopo circa 30 minuti nel caso di non utilizzo. Premere

brevemente il tasto ON-OFF

e attendere che la

macchina si riattivi.

La pagina sta caricando ...

HOTPOINT/ARISTON AQLF8F 292 U (EU) Guida utente

HOTPOINT/ARISTON AQLF8F 292 U (EU) Guida utente

in altre lingue

Documenti correlati