Comelit IPPTZ120IRD Manuale utente

Categoria
Telecamere di sicurezza
Tipo
Manuale utente

Questo manuale è adatto anche per

IP PTZ CAMERA
ART. IPPTZ120IRD IPPTZ130IRB
Please read this manual thoroughly before use and keep it for future reference
Contents
1. Introduction .............................................................................................................................................................................. 1
Features .............................................................................................................................................................................. 1
2. Hardware Installation ............................................................................................................................................................... 2
System requirement ............................................................................................................................................................ 2
Installation environment ...................................................................................................................................................... 2
Installation environment requirements ........................................................................................................................ 2
Recommend operating environment .......................................................................................................................... 2
Hardware installation steps ........................................................................................................................................ 2
Network connection .................................................................................................................................................... 3
Connection instruction ........................................................................................................................................................ 4
3. Operating Guide for Network High Speed Dome ..................................................................................................................... 5
Set the IE Browser .............................................................................................................................................................. 5
Download and Install ActiveX .............................................................................................................................................. 6
Login ................................................................................................................................................................................... 7
Live view ............................................................................................................................................................................. 8
System specification setting .............................................................................................................................................. 11
System ..................................................................................................................................................................... 11
Basic info ......................................................................................................................................................... 11
User manage ................................................................................................................................................... 15
PTZ Config ...................................................................................................................................................... 15
Record ............................................................................................................................................................. 17
Time zone ........................................................................................................................................................ 19
Micro-SD status ............................................................................................................................................... 20
AV ............................................................................................................................................................................. 21
Video channels ................................................................................................................................................ 21
Video parameters ............................................................................................................................................ 22
Privacy Mask ................................................................................................................................................... 23
Shot parameters .............................................................................................................................................. 24
Image parameters ........................................................................................................................................... 25
Network .................................................................................................................................................................... 26
Ethernet ........................................................................................................................................................... 26
DDNS .............................................................................................................................................................. 27
Netport ............................................................................................................................................................. 28
Other protocol .................................................................................................................................................. 29
P2P .................................................................................................................................................................. 29
Alarm configuration .................................................................................................................................................. 30
Alarm Conf ...................................................................................................................................................... 30
IO Alarm .......................................................................................................................................................... 30
Motion .............................................................................................................................................................. 31
Local......................................................................................................................................................................... 33
Local ................................................................................................................................................................ 33
Playback ........................................................................................................................................................................... 34
4 Appendix ................................................................................................................................................................................. 35
Specifications art. IPPTZ120IRD ....................................................................................................................................... 37
Specifications art. IPPTZ130IRB ....................................................................................................................................... 37
Network Interface of Network High Speed Dome .............................................................................................................. 39
Default Network Parameters ............................................................................................................................................. 39
Frequently asked questions .............................................................................................................................................. 39
CAUTION
Non-technician should not try to operate this high speed dome before reading this manual carefully. (This manual are subject to
change without prior notice.)
Cut the power supply off before operating the device to avoid damage caused by mal-operation.
Interior of the camera are precision optical and electrical instruments. Heavy pressure, shock and other incorrect operations should
be prevented. Otherwise, may cause damage to product.
Please do not use the product under circumstances where the limits exceed the maximum specified temperature, humidity or power
supply specifications.
Contents in this manual may be different from the edition that you are using. Should any unsolved problem occur given that the
product is used according to this manual, please contact our technical support department or your product suppliers.
This manual content will be updated unscheduled, our company reserves the right to do manual contents update without further
notice.
The default username for this device is “admin”, and the password is “blank”. Default IP address is 192.168.1.188, HTTP port is 80.
PACKING LIST
Open the package, and check whether the accessories all contained.
Part
Quantity
IP speed dome (Include bracket)
1
Power supply
1
Screws bag
1
CD
1
Glove
2
Note:
When open the box, please check all of parts carefully, confirm the parts as same as packing list.
Please read the user manual carefully before the installation.
Make sure to turn off all the power when install the camera
Please confirm the power transformer, avoid the device damage with unmatched power source
Contact your local retailer without hesitate if anything is missing in your package.
1
1. Introduction
Features
Build in 20x / 30X optics zoom lens, 2MP / 3MP, 1~60 fps
True Day/Night switch
H.264 High Profile/MJPEG encoding, VBR/CBR, dual stream
Privacy mask, motion detection
Alarm linkage output, micro-SD card video recording, snapshot, FTP upload, Email inform, link preset, CMS inform
ONVIF 2.2 Profile-S protocol, GB/T28181 protocol
360° horizonal continuous rotation; vertical -90°,255 presets
Low power consumption MTTF up to 30,000 hours
2CH alarm input, 1CH alarm output, build in micro-SD card slot, audio input/ output, 100 Mbit/s Ethernet
IP66 protection level
2
2. Hardware Installation
System requirement
LAN or WAN Internet to connect server, via PC Ethernet (network card or network cable) TCP/IP protocol connect , suggest
Internet Explorer 8.0 version or later.
Monitor and PC configuration:
CPU: Dicaryon 2.8G or later, RAM: 512M or later (Above DirectX 8.1)
Monitor: 17", 1920×1080 resolution
Operation system: Windows NT, Windows2000, Windows XP, Windows 7 or later
Installation environment
Installation environment requirements
Far away from humid or high-temperature environment; choose proper place for ventilation; avoid installing on shaky place and try to
stay away from heat device.
Recommend operating environment
-20°C60°C
Hardware installation steps
Please make sure LAN and WAN are working in order before installation of the Network High Speed Dome. After checked all the
network system in good condition, keep your hands clean and dry, following the steps below.
Unpack the box to check the goods
Take out all goods which needed for installation from the box
Take off the protection cover and insert the SD card. Please refer to the SD card installation steps below.
Remove the ornament
screws (2pcs), then take it off
Loosen the screws of
horizontal installation panel
(4pcs), then put up the panel
for a little
3
Connect related cables according to need (Power line, network line, audio line etc.)
Connect the power supply
Note:
Please read the user manual carefully before the installation.
Make sure to turn off all the power when install the camera
Please confirm the power transformer, avoid the device damage with unmatched power source
Network connection
LAN connection
Use one network line to connect Speed Dome with concentrator or switchboard of the LAN. As Figure below.
Users also can use one network line to connect IP Speed Dome with computer network card or switchboard.
WAN connection
Use one network line to connect IP Speed Dome with router or XDSL Modem/Cable Modem. As Figure below.
Fig. Devices connection scenarios
router
switch
web browser
web browser
IP camera
IP camera
IP camera
Insert micro-SD card
(IPPTZ120IRD)
Insert micro-SD card
(IPPTZ130IRB)
Loosen the screws of back
cover (4pcs) and take off the
cover
4
Connect the power supply
After connect the power source, the IP speed camera will start operation automatically.
Connection instruction
5
3. Operating Guide for Network High Speed Dome
Set the IE Browser
Because the high safety level of the IE browser, If you visit Network High Speed Dome for first time, Please set the IE browser.
Setting method: open the IE browser, click Internet Option into the "Security" page, click the "Custom Level" and then follow steps to
set the IE browser
6
Download and Install ActiveX
Users have to install ActiveX Control when visit Network High Speed Dome at the first time via IE browser.
Download and install the ActiveX:
Input the IP address of Network High Speed Dome (default IP: http://192.168.1.188) in Internet Explorer to enter into login page.
At the login interface, click “Download ActiveX”. As shown in Figure 3-1 :
Figure 3-1
Popup control installation information, click “Run”. As shown in Figure 3-2:
Figure 3-2
A file download dialog will pop out, click “Install” to installation. As shown in figure 3-3:
Figure 3-3
7
Click “Finish” to complete the ActiveX installation. As shown in figure 3-4:
Figure 3-4
Login
Reopen Internet Explorer after ActiveX installation completes, input IP address (http://192.168.1.188) of the Network High Speed then
turn to login page, input username (default is admin) and password (default is blank), click login to enter into main interface (as shown in
Figure 3-5)
Figure 3-5
8
Live view
Live preview interface as shown infigure 3-6:
Figure 3-6
In the Live view interface, users can do remote operations such as master/slave stream video preview, voice intercom, listen,
Record, full-screen preview, Snap picture, PTZ control, preset, area scan, pattern scan, PTZ watch, preview video image volume adjustment,
Day/Night switch, Image Flip, Image Mode, etc.
Master/slave stream: notice the buttons at the left lower corner, click it to switch the preview mode.
Voice intercom: connect a sound box at the device voice output port, then connect a mike at the PC port. Click microphone icon
, then adjust the volume, the voice intercom between PC and Network High Speed Dome can be performed.
Listen: connect a sound pick-up at the device audio input port, click the audio icon , users can call real time monitoring at PC
port.
Snap picture: click icon to do screen video capture, it will create BMP picture and store in the specified folder automatically.
The default file storage path is C:\IPCamera, users can set it at the Setting→Local→Local setting .
Full screen: click icon to get full screen preview, press ESC or right mouse click to exit full screen preview.
Record: click icon to do manual video operation and store in the specified file automatically (Video format is mp4, the default
file storage path is C:\IPCamera\, users can set it at the Setting→Local→Local setting .
3D positioning: 3D position function can be opened or closed.
Switch the sidebar: click or icon to switch to the sidebar.
Image parameters adjustment: Users can adjust the image parameters at the video preview interface, such as image brightness,
hue, contrast, saturation and sharpness, etc. as shown in Figure 3-7:
9
Figure 3-7
Day/Night switch: according to the surveillance need, users can set color model, black model, auto model. As shown in Figure 3-8:
Figure 3-8
Image Flip: via the buttons to adjust image rotation, support horizontal rotation , horizontal+vertical rotation . As shown
in Figure 3-6.
Image Mode: Divided into outdoor, indoor, three models automatically, the default for auto. As shown in Figure 3-6.
Click PTZ at the video preview interface to turn to PTZ configuration interface. As shown in
Figure 3-9:
Figure 3-9
PTZ control: user can do horizontal 360°/vertical 90°overall monitoring via PTZ configuration buttons , PTZ operation
speed 1-63 levels adjustable
Area scan: via the PTZ buttons to set area scan, click to set left limit, click to set right limit and area scan
remembered automatically. Click to call area scan. As shown in Figure 3-9.
10
PTZ Watch: at the PTZ Watch drop down list, users can select the PTZ watch type (Include close, preset, CRZ, pattern, area, etc)
and set the idle time, then click to save it. As shown in Figure 3-10.
Figure 3-10
Preset: adjust the camera to the appointed angle and location through directional buttons, and then select a preset number in the
preset drop down list, click to set it. There are 1-255 presets can be set, and users can click to delete the preset, click
to call the preset. As shown in Figure 3-9.
Pattern scan: at the pattern scan drop down list, users can select the pattern scan number, and edit the pattern scan name. Then
click to start recording, click to stop recording, pattern scan remembered automatically. Click to call pattern
scan. As shown in Figure 3-9.
CRZ: At the CRZ drop down list, users can select cruise number, click to add preset, set the delay time. Select preset ID and
click to delete it. Finally click to save it and click to call cruise. As shown in Figure 3-11.
Figure 3-11
11
System specification setting
System
Basic info
1) System information
Click Setting→ System→ Basic info→ Sysinfo, IP Speed Dome “Sysinfo” interface. As shown in figure 3-12:
Figure 3-12
Device Name: edit the camera name
Device Number: display the device serial number
Hardware Version: display the device hardware version number
UBOOT Version: display the product system UBOOT version number
Kernel Version: display the product system kernel version number
App Version: display the product software version and the system version date
PTZ Version: display the IP speed dome version model
OCX Version: display the OCX version number
Note:Based on the version information which displayed in factory product
After setting complete, click to save it.
12
2) System operate
Click Setting→ System→ Basic info→ Sysoperate, IP Speed Dome “System operate” interface. As shown in figure 3-13:
Figure 3-13
Reset: Restore factory settings
Reboot: click to do IP speed dome reboot operation
Parameters type: select the parameters type which you have to derive
Parameter input: select the configure file which you need and click
Parameter output: select the configure file which you need and click
After setting complete, click to save it.
13
3) Update
Click Setting→ System→ Basic info→ Update, IP Speed Dome “Update” interface. As shown in figure 3-14:
Figure 3-14
System update: system update online.
Operation method:
Click ,find the specified file and select the upgrade package. As shown in Figure below:
Click , system upgrade automatically;
After system upgrade successfully, the following window will pop out, click . As Figure below:
Reopen the IE browser and input the IP address, after log in, check the whether the software version is updated.
14
Note: after system upgrade successfully, you need to reset camera data in "Sysoperate",clear IE cache and install
ActiveX again before logging in web system. (Clear IE cache as Figure below)
4) Log query
Click Setting→ System→ Basic info→ Log Query, IP Speed Dome “Log Query” interface, as shown in Figure 3-15:
Figure 3-15
Type: select the alarm log type, all/ alarm/ exception/ operation/ information are optional
Begin time/ End time: set the log search time period, click icon and the log information will display.
After setting complete, click to save it.
Non-professional technicians do not operate the system upgrade.
Please do not power off during installing update.
15
User manage
Click Setting→ System→Usermanage, IP Speed Dome “UserManage” interface, as shown in Figure 3-16:
Figure 3-16
Add user: add a new user and select the new user limits of authority
Modify: select the added user and modify the user password
Delete: delete the added user
After setting, click to save it.
PTZ Config
1) Serial setting
Click Setting→ System→ PTZ Config→ SerialSetting, IP Speed Dome “SerialSetting” interface, as shown in Figure 3-17:
Figure 3-17
16
Address: click to select or modify the camera address
Baud rate: click to select or modify the baud rate
Protocol: click to select or modify the protocol
After setting, click to save it.
2) Schedule Task
Click Setting→ System→ PTZ Config→ Schedule Task, IP Speed Dome “Schedule Task” interface, as shown in Figure 3-18:
Figure 3-18
Start time: click the checkbox to turn on or turn off Schedule task
Task restart: set the restart time if schedule task was broken off
Cur setting: set the current schedule task time, max 10 periods/ day.
After setting, click to save it.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133

Comelit IPPTZ120IRD Manuale utente

Categoria
Telecamere di sicurezza
Tipo
Manuale utente
Questo manuale è adatto anche per