Metos Kodiak20 Manuale utente

Metos
Marca
Metos
Modello
Kodiak20
Categoria
Miscelatori
Tipo
Manuale utente

Questo manuale è adatto anche per

Varimixer A/S
Kirkebjerg Søpark 6
DK-2605 Brøndby
Denmark
P: +45 4344 2288
E: info@varimixer.com
www.varimixer.com
KODIAK
KODI A K 20
Operating Instructions
EN
Ordrenummer: 00613
Translation of the original user manual
Nov 2018
2
General:
This manual should be seen as an integral part of the mixer and should be kept by the machine throughout its working life.
Before the machine is commissioned, it is important to read these instructions thoroughly, particularly the section on user safety.
The manufacturer may update the product manual without updating this copy of the manual.
The manufacturer will not be liable for faults caused by:
• Careless, improper or incorrect use of the mixer
• Non-standard use (not for the purposes described in the manual)
• Incorrect installation
• Incorrect power supply to the machine
• Failure to comply with maintenance instructions
•
Modicationstothemachine
• Sparepartsandaccessoriesthatarenotoriginalorspeciedforthismodel
• Failure to comply with instructions in this manual
In case of faults with the mixer, please contact the supplier.
The guarantee does not cover damage caused by misuse, overloading or the user’s failure to comply with the maintenance
instructions
.
UnpackinG:
The machine should be unpacked and the packaging disposed of according to regulations applicable in the country concerned.
Before the mixer is removed from the pallet, check that all parts are present with the machine:
• Safety guard and
llingchute
• Power cable
•
32mmxedspannerforlegs.
• Bowltrolleyforoormodel
• Bowl, whip, beater, hook and scraper with blade, if these were selected with the order.
The machine can be released from the pallet by cutting the strips.
contents:
General: ....................................................................................................................................................................... 2
UnpackinG: ....................................................................................................................................................................... 2
transport: ....................................................................................................................................................................... 3
installation, adjUstments and fixinG: ................................................................................................................................ 3
technical data: ................................................................................................................................................................. 4
layoUt drawinGs: ............................................................................................................................................................... 4
commissioninG: ................................................................................................................................................................... 5
recommended Use of the machine: ...................................................................................................................................... 5
safety: ....................................................................................................................................................................... 5
workinG with hot inGredients: ........................................................................................................................................... 6
max. capacity of the machine: ............................................................................................................................................ 6
eqUipment: ....................................................................................................................................................................... 6
components of the machine: .............................................................................................................................................. 7
kodiak User-friendliness: .............................................................................................................................................. 8
operatinG the mixer: .......................................................................................................................................................... 9
overloadinG: ................................................................................................................................................................... 10
procedUre in case of overloadinG: .................................................................................................................................. 10
recommended speeds: ...................................................................................................................................................... 10
recommended speeds for attachment drive: ..................................................................................................................... 10
correct Use of tools: ..................................................................................................................................................... 10
cleaninG: ..................................................................................................................................................................... 10
lUbrication and Grease types: ......................................................................................................................................... 10
attachment drive: ............................................................................................................................................................ 10
systematic maintenance: ...................................................................................................................................................11
readinG the machines data and the error loG: ..................................................................................................................11
error codes and possible solUtions: ............................................................................................................................... 12
access to the fUse: ......................................................................................................................................................... 13
example electrical connections: ..................................................................................................................................... 13
circUit diaGram: .............................................................................................................................................................. 14
3
12
79 cm
transport:
Lifting equipment should always be used to move the machine. .
The machine must not be pulled or lifted by the bowl lift handle.
When the machine is moved, it should be in a vertical position at all times.
installation, adjUstments and fixinG:
The ambient temperature around the machine must not exceed 45
o
C.
Especially for oor model - Adjustments:
The height of the legs should be adjusted so that the bowl on the bowl trolley
tsperfectlyintothebowlarms.
Thebowlarmsshouldbeatthecorrectheightabovetheoorbeforethe
machine is taken into use – see “Condition 1” and Condition 2.
It is of the utmost importance that the machine’s legs are adjusted so that the
conditions described by the following sketch are met:
Condition 1:
Thetopofthemixermustbeparalleltotheoor.Toensurethisyoumustmeasurethedistancefromthetopofthema-
chinetotheoor:
The dimension must be the same when measured at the front of the mixer
and at the rear of the mixer:
Condition 2
Themixermustbeheightadjustedsothatthebowlonthebowltrolleytsexactlyinthebowlarms:
Basically,thedimensionfromoortocentreoftheknobsonthebowlarmsmustbe79cm.Ifthebowlonthebowltrolley
doesnottexactlyinthebowlarmsatthisdimension,adjustslightlyonthefrontlegsofthemixer.
Especially for table model - xing and adjustment:
Kodiak 20 table model must be xed to the table it is placed on.
Kodiak20tablemodelisxedwithboltsinthetwohindlegs
.
Bolts with dimensions M10 x 20 mm + table top thickness and a
washer are used.
The table must be suitable for machine’s weight and operation.
Height adjustment:
Ifthetableisnotfullyeven,justicationscanbemadebyadjusting
the two front legs.
Theadjustment ismade asdescribed forthe oormodel -see
above.
To raise leg
turn
clockwise
To lower leg
turn
anticlockwise
Together with the mixer
comes a 32 mm fixed
spanner to be used for
adjustments.
4
1292
770
471
631
579
482 100
283
7
7
1
7
8
7
Electrical connection:
Before the machine is connected to the mains, check that the voltage and frequency printed on the name plate
are correct for the installation location. The name plate is positioned uppermost on the back of the machine.
There is a risk of injury if the machine is not earthed.
It must be ensured that the cable used to connect the machine to the mains meets the standard for the country
in which the machine is installed. See also Example electrical connections, page 14
The mixer must be earthed. Failure to do so may cause injury. If there is no earth connection, the EMC
lterwillnotwork,withtheriskofdamagetothefrequencyconverter.
When the machine is connected, phase + neutral + earth or phase + phase + earth should be used. In
both cases, it is important to ensure that the voltage between the two live pins matches the name plate.(See
examples on page 13)
The machine must only be connected to an earthed mains supply.
A plug with two pins plus earth should be used. Alternatively, two wires plus earth from a three-phase supply
may be used.
The machine should be protected by a differential switch.
The machine is protected by a 10A fuse. The fuse is built into the socket on the back of the machine.
Users can connect the mixer to the power supply themselves; refer to the section on Electrical connection which must be
followed.
Forthebenetofservicestaff,itshouldbecleartoseewhenthemainsplugtothemixerhasbeenremovedfromthe
socket in the wall.
Thecableisxedtothemachineintheplugmadeofsilicone,see“Components of the machine” page 7.
technical data:
Kodiak 20 Gross weight Net weight kW Volts Amps Variable speed, tool
Model kg kg kW V A rpm
Floor model 179 154
0,75 230 6,3 64 - 353
Table model 97 72
layoUt drawinGs:
Floor model:
Table model:
5
commissioninG:
Bowl,tools,safetyguardandllingchuteshouldbecleanedbeforeuse–seesectionon“Cleaning”, page 10.
Floor model: The bowl arms must
beatthecorrectheightabovetheoorbeforethemachineistakenintouse–see“Instal-
lation, adjustments and xing”, page 3
Table model: The mixer must
bexedtothetable,see“Installation, adjustments and xing” page 3.
recommended Use of the machine:
The machine is designed for the manufacture of products that do not trigger any reactions or release sub-
stances that may be harmful to the user when in use.
The machine must not be used in an explosive atmosphere.
The mixer must only be operated by staff who have been trained in the use of the machine according to these
instructions. Users must be over 14 years of age.
The mixer is designed for commercial use in kitchens, catering outlets and bakeries.
Themachinemayonlybeusedasspeciedinthismanual.
Only bowls designed for Kodiak 20 may be used.
Tools should be used in conjunction with the corresponding bowl – a 20L tool with the 20L bowl and a 20/12L tool with the
20/12L bowl.
Unless the change is recommended by the manufacturer, modifying the machine is prohibited.
Ifthemachineisttedwithanattachmentdrive,onlyaccessoriesproducedorrecommendedbyVarimixer A/S should be
attached.
safety:
The machine is designed for the manufacture of products that do not trigger any reactions or release sub-
stances that may be harmful to the user when in use.
Users must be over 14 years of age and trained in the use of the machine according to these instructions.
User safety is assured as follows:
• Tools can only rotate when the safety guard is in place and the bowl is lifted.
• The safety guard is made of polycarbonate. It is not possible to attach the guard incorrectly.
• No access to rotating tools.
•
Thespreadofourdustisinhibited.
• Equipped with emergency stop - The tool stops rotating in less than 4 seconds (also for normal shut-down and stop via
safety guard).
• Clearance between guard/stand and lifting handle at least 50 mm.
•
Noiselevelunder70dB.
• Machine remains stable on a slope of up to 10
o
.
The machine is protected against overvoltage.
Non-ionising radiation is not produced intentionally, but rather technically conditioned by electrical equipment (e.g. electric
motors, live power lines or solenoids). The machine is not equipped with strong permanent magnets. By maintaining a safe
distance(betweentheeldsourceandimplant)of30cm,anyimpactonactiveimplants(e.g.pacemakers,debrillators)
can likely be prevented.
The machine should be positioned to allow space for normal use and maintenance.
Good ergonomics for the user is ensured by the accompanying bowl trolley, which eliminates heavy lifting of the bowl and
maintains the right working height.
There is a risk of injury if the machine is not earthed.
It must be ensured that the cable used to connect the machine to the mains meets the standard for the
country in which the machine is installed. See also ‘Electrical Connection’ page 4.
Placing your hands in the bowl while the machine is running may cause physical injury.
The following recommendations apply to work with powdery ingredients:
• Powdery ingredients should not be poured into the bowl from a great height.
•
Bagsofe.g.ourshouldbeopenedatthebottom,downinthebowl.
• Do not run up to the maximum speed too quickly.
6
workinG with hot inGredients:
Whenworkingwithhotingredientswhichareaddedviathellingholeinthesafetyguard,itisnecessarytousethellingchute.
ThellingchuteismadeofFDA-gradesilicone,andisabletowithstandhotingredientsupto200
o
C.Thellingchutecan
be used for ingredients as hot as this for as long as necessary.
Ifthellingchuteisnotused,ingredientswhichareaddedviathellingholeinthesafetyguardmustnotbemorethan60
o
C.
max. capacity of the machine:
AR = absorption ratio (%AR)
(liquid as % of dry matter)
E.g. a basic recipe includes 1 kg dry matter and 0.6 kg liquid:
this gives AR = 0.6 kg x 100
= 60%
1 kg
If, for example, the maximum capacity of the mixer is required, the calculated
AR = 60% is used to determine the amount of dry matter and liquid in the dough:
Maximum capacity of the machine = 11 kg for dough with AR = 60%
Now the weight of the dry matter in this dough is calculated as follows:
Dry matter = max. capacity x 100 = 11 kg x 100 = 6,875 kg
AR + 100 60 + 100
Weight of liquid = 11 kg - 8.125 kg = 4.125 kg
Local variations in the quality of the raw materials may affect water absorption, volume,
baking characteristics etc., and hence capacity.
Capacity pr. mix Tool Kodiak 20
Egg white Whip 2,4 l
whipped cream Whip 5 l
Mayonnaise * Whip 16 l
Herb butter Beater 10 kg
Mashed potatoes * Beater/Whip 12 kg
Yeast dough (50% AR) **
Hook 10 kg
Yeast dough (60% AR)
Hook 11 kg
Ciabattadough (70%AR) Hook 12 kg
Mufns * Beater 14 kg
Cake base Whip 5 kg
Meat ball mix * Beater 15 kg
Ising Beater 14 kg
Doughnut (50%AR) Hook 12,5 kg
Standard equipment, as follows:
Bowl 20 l
Hook, whip and beater for 20 l bowl
Asiliconelling-chuteforhotingredients
Optional accessories:
Scraperfor20lbowl,ifmixeristtedforascraper
Bowl 12 l
Hook, whip and beater for 12 l bowl
Scraperfor12lbowl,ifmixeristtedforascraper
Standard equipment for oor model
Bowl trolley
eqUipment:
7
Filling chute
Socket on the back of the ma-
chine; contains 10A fuse, see
page 13.
components of the machine:
Table model must
be bolted to the
table, see page 3
Lifting handle
Bowl truck
Onlyoormodel
Bowl
Control panel
Safety guard
Mixer head
Mixer tool
Control panel with
attachment drive
Adjustable legs; see page 3
for adjustment
Bowl arms; see page 3
for attachment between
bowl arms and bowl
8
kodiak User-friendliness:
KODIAKhasdesignedinpartnershipwithkitchenandbakerystaff,whichhasresultedinanumberofuserbenets:
The machine itself
Can be connected to the mains by the user
Is made of stainless steel
Theoormodelhasheight-adjustablefeettoensurethatthehighbowltrolleyworksproperly
Is easy to clean, with large surfaces and a removable safety guard which can be machine-washed
The power cord is connected to a waterproof silicone plug and can not be shaken from the machine
The inclined control panel combined with the large bowl diameter provides a good view of the contents of the bowl.
The machine is equipped with a spring that helps to lift and lower the bowl
Control panel:
The control panel is simple and intuitive, with large push buttons.
The speed can be increased/decreased continuously by holding down
and . It is also possible to ‘step’ between the
predenedspeeds
The panel is inclined at the ergonomically correct height, making it very comfortable to use.
The panel is easy to clean with a damp cloth.
There is a built-in timer function with a display, which can also be used to show the number of operating hours.
Safety guard:
The one-piece safety guard is made of transparent plastic. The guard is easy to
remove and clean. The guard can be machine-washed at up to 60
o
and can withstand
upto90
o
for short periods.
Theloosesiliconellingchutewithstandsbeingexposedtohotingredientsupto
200
o
C, and is dishwasher-safe
The guard is made of a special impact-resistant material which can withstand daily
use in a commercial kitchen.
The safety guard is held in place by magnets, so there are no loose parts that can
break or collect dirt.
It is not possible to attach the guard incorrectly.
A force corresponding to 3 kg or 30 N should be used to remove the guard.
Thellingholeinthesafetyguardcanbeturnedtosuittheuser’sneeds.
Bowl and bowl trolley:
The bowl is not very deep but has a large diameter, which makes it easier to see
the contents while working.
The bowl does not have to be lifted into place in the bowl arms, but can be wheeled
directly into position.
The bowl trolley is used for transfer from mixer to workbench, dishwasher, stores etc.
The bowl trolley provides an ergonomically correct working height.
The bowl trolley spares the user any heavy lifting.
The bowl can be tilted in the rubber ring on the bowl trolley.
Tools:
The mixer whip is very compact in design, which provides for a long service life. It must be handled according to these in-
structions.
The bowl, beater, hook and whip are made of stainless steel.
9
Before starting the machine:
Floor model: Place the bowl in the bowl trolley. Put the desired
tool into the bowl and wheel it into position between the bowl
arms. Ensure that the bowl is correctly engaged with the bowl
arms; see “Installation, adjustments and xing”, page 3.
Table model: Put the desired tool into the bowl and place the
bowl in the bowl arms.
Fitthesafetyguardandturnitsothellingholeisaccessible
when the machine is running. Theloosellingchutemustbe
used if it is necessary to add hot ingredients during the process
(i.e. ingredients at temperatures above 60
o
C).
Turnthetooltolockitintothebayonettting.
Lift the bowl with the aid of the lifting handle.
The mixer is now ready to start.
It is possible to set both the running time and speed before
starting the machine; see next section:
Start the machine:
Press to start the mixer.
Press
next to to increase the speed.
Press
next to to reduce the speed.
The speed is shown as a number on the scale
.
The display 1 represents the lowest speed,
approx. 64 rpm.
The display
12345678 represents the highest speed,
approx. 353 rpm.
Ifaspecicstartspeediswanted,yousetthespeedandthen
start the mixer by pressing .
Display of running time – Timer function:
Select a running time for the mixer by pressing next to
. The running time is shown in minutes and seconds in
thetimereldbetween and .
Runningtimesofupto90minutesareavailable.
When the mixer is running, the running time will not be reset if
is pressed once; press once more and it will be reset.
If no running time is selected, the display will show the time
elapsed since the mixer was started.
If the time set on the timer runs out while the mixer is running,
the mixer stops and you hear a bib.
Inspection of ingredients while in use:
If the mixer needs to be stopped temporarily without affecting
the running time, press
. The mixer will slow down and
then stop and the running time will stop too.
The bowl can now be lowered and the ingredients checked.
Lift the bowl and press
, and the mixer will start and the
running time will resume.
Stop the machine:
To stop the machine:
• Press
. Running time not reset.
• Press
twice. Running time reset.
• Press the emergency stop - the running time will be reset.
• ‘Tilt’ the safety guard - the running time will be reset.
• Lower the bowl - the running time will be reset.
In all cases the mixer can be restarted by pressing
.
It will start at the lowest speed.
operatinG the mixer:
Emergency stop
Stop
Increase time
Timer (timer eld)
Decrease time
Speed indi-
cator
Decrease speed
Increase speed
Start
10
12345678
12345678
12345678
XXXXX
XXX
12345678
12345678
XXXX
overloadinG:
The mixer must not be overloaded.
Possible overload situations:
• Working with excessively tough and heavy dough
• Mixer tool exceeding the recommended speed
• Wrong mixer tool being used.
Larger lumps of fat or chilled ingredients must be reduced
before they are placed in the bowl.
Overloading will cause the frequency converter to stop the
machine.
,
or
will be displayed in the timer
eld.
Follow the description under “Procedure in case of over-
loading”.
procedUre in case of overloadinG:
Spot the error code in the section “Error codes and possible
solutions”, page 12 and follow the suggestion for a solution.
When done, remove the error code by pressing
.
The mixer can now be restarted by pressing
.
recommended speeds:
correct Use of tools:
Recommended uses of tool:
The whip should not be struck against hard objects
such as the edge of the bowl. This will shorten the
life of the tool because of increasing deformation.
To make mashed potato, use the beater and then
the standard whip.
cleaninG:
The machine may only be cleaned by trained
staff over 14 years of age.
The machine should be cleaned daily after use. It should be
wiped with a soft brush and clean water. Sulphonated soaps
should be used with care, as they destroy the lubricants in
the machine.
The machine should never be rinsed with a hose.
The machine parts made of aluminium – bowl arms
and bowl trolley – must not be washed with very
alkaline cleaning agents (pH must be between 5.0
and 8.0).
Please note that the plastic safety guard may be
damaged if it is exposed to high temperatures for a
prolonged period. (Max. temperature 60ºC)
Thellingchuteisdishwasher-safe
The soap suppliers may be able to help by recommending
the right type of soap.
lUbrication and Grease types:
Lubrication and other servicing may only be carried
out by trained staff over 14 years of age.
The lid of the mixer may only be removed when the
cable to the mains supply has been removed.
When repairs are made to the mixer head, the gear wheel
and internal gear should be lubricated with Molykote G-1502
the needle bearings in the mixer head can also be lubricated
with this type of grease.
If the machine is supplied with an attachment drive, the gear
for the attachment drive should be lubricated with Statoil
GreaseWay LiCa 80.
Donotuseanyothergreasetypesthanthosespeciedabove.
attachment drive:
Themachinemaybettedwithanattachmentdriveinto
which optional accessories, such as meat mincers and
vegetable cutters, can be attached.
For further information on the assembly and use of op-
tional accessories, please refer to the manual that comes
with the accessory.
The machine must be shut down when the acces-
soryisttedtotheattachmentdrive.
recommended speeds for attachment drive:
Whip Beater Hook
Cream Cake mix Bread dough
Egg whites Buttercream Rye bread
Mayonnaise
Wafemix etc.
etc. Forcemeat
etc.
11
Part Action Frequency Note
Safety guard Check the safety of the safety guard:
Does the tool stop rotating when the
guard is tilted/removed?
Regularly
If the tool does not imme-
diately stop rotating on tilting/
removal of the guard, the ma-
chine must not be used.
Call the engineer
Emergency stop Test the emergency stop: Does the tool
stop rotating when the emergency stop
is activated?
Regularly
If the tool does not imme-
diately stop rotating on activa-
tion of the emergency stop, the
machine must not be used.
Call the engineer
Mixer head The mixer head should only be lubri-
cated on repair, see the section “Lub-
rication and grease types”.
During repairs
The machine’s other
moving parts
The moving parts that belong to the
bowl’s lifting mechanism all run in
maintenance-free plain bearings and
should not therefore be lubricated.
Never
Attachment drive The rubber plug for covering the open-
ing of the attachment drive should be
on the machine and be intact.
Daily
The rubber plug must cover
the opening on the attachment
drive when the latter is not in use.
Cleaning Follow the instructions in the section
“Cleaning”
Follow the instructions
in the section “Cleaning”
systematic maintenance:
readinG the machines data:
Press the stop button for 5 sec. The machine’s data will then be displayed as alternating text in the display. There are
vereadingscorrespondingtothevedatasetsdescribedbelow:
• Data set 1: Statesrmwareversion,displayedas“F”followedbythreegures,e.g. =rmwareversion3.
• Data set 2: Statesthemachine’srunningtime,displayedas“t”followedbythreegures,whichindicatethenumberof
9.999-minutecycles,e.g. =2x9.999min.,or19.998min.
• Data set 3: Displaysfourgures,whichindicatethenumberofminutesthecurrentcyclehasbeenrunning,e.g.
= 1.234 min.I.e., if is displayed followed by ,themachinehasbeenrunningfor19.998min.+1.234
min., or a total running time of 21.232 min.
• Data set 4: States the number of times the machine has been disconnected from the power supply (plug pulled out of
themachine/powercut/switchedoff)andrestarted,displayedas“r”followedbythreegures,whichindicatethenumber
of restarts, e.g. = 2x9,999restarts,or19,998restarts.
• Data set 5: Displaysfour gures,which indicatethe numberof restartswhich havehappened inthe current cycle,
e.g. = 1234 times. In other words, if is displayed followed by , the machine has restarted a
totalof19,998+1,234times,or21,232times.
readinG the error loG:
It is possible to display a log of the errors that have occurred:
• Hit emergency stop and press next to .
•
Thedisplayshowsthelatesterrorrst.
• To scroll back through the errors, press next to ; to scroll forward, press next to .
• The last eight errors can be displayed.
• Deactivate emergency stop to cancel the display
12
error codes and possible solUtions:
For some errors, the control system will show an error code in the display:
User pressed without raising the bowl to working height.
Solution:
Raise bowl to working height.
User pressed withoutttingthesafetyguard.
Solution: Fit the safety guard.
The Thermal sensor in the motor has overheated.
Solution: The error will disappear when the temperature has dropped to an acceptable level.
Stop the mixer and reduce the quantity of ingredients in the bowl. When it starts again, select a lower speed.
There is an error in communication between the control panel and the frequency converter.
Solution: Call the engineer.
Error in frequency converter.
Solution: Call the engineer.
Thermal sensor in the frequency converter has cut out.
Solution: The error will disappear when the temperature has dropped to an acceptable level.
Intermittent low voltage in the power supply.
Solution: The power supply to the mixer should be checked by an expert.
Intermittent high voltage in the power supply.
Solution: The power supply to the mixer should be checked by an expert.
The mixer is overloaded - continuously for 50 seconds
Solution:
Reduce the quantity in the bowl; alternatively, the product may need to be divided into smaller parts or diluted
before the machine is restarted. When restarted, select a lower speed, if speed was the problem
The error code is removed by pressing
The mixer is overloaded - momentarily (overloaded 8 times within 20 seconds
Solution:
Reduce the quantity in the bowl; alternatively, the product may need to be divided into smaller parts or diluted
before the machine is restarted. When restarted, select a lower speed, if speed was the problem.
The error code is removed by pressing
Blockage.
Solution: Remove the object that caused the blockage.
The error code is removed by pressing
,
and
can also occur when using the attachment drive.
13
Local 50/60 Hz supply. Name plate
Power supply:
phases x voltage
With
neutral
Earth Voltage Phas-
es
Use
neutral
Use
earth
Notes
1 x 220-240V Neutral yes 230V 1 yes yes
Note that the machine must not be con-
nected without an earth, as this may com-
promisetheactionoftheEMClterby
removing the discharge to the ground, and
may be dangerous for the user.
For functional and safety rea-
sons, the machine must be con-
nected to the earth.
2 or 3 x 220-240V - yes 230V 2 - yes
2 or 3 x 380-415V Neutral yes 230V 1 yes yes
2 or 3 x 380-480V - yes 380-480V 2 - yes
example electrical connections:
access to the fUse:
If the fuse burns out, it can be replaced without the aid of technical staff.
• The fuse is located in the socket on the back of the machine.
• Be sure to remove the power cord before changing the fuse
14
circUit diaGram:
Page
Previous page:
Next page:
Total no. of pages:
Last print:
Last edit:
Page rev.:
Project rev.:
Appr. (date/init):
Eng. (proj/page):
Dwg. no.:
Case no.:Project title:
Customer:
Page title:
File name:
Page ref.:
DCC: Scale:
Kodiak VL1C 5
12
Diagram
PCSCHEMATIC Automation
37.020-13.02.01
4
9
01
CE / CE
&FS 1:1
1 2 3 4 5 6 7 8
12 12
-S3
12 12
-S2
PTO
PTO
PE
L!
L2
L3
M
3
PTO
PTO
PE
L!
L2
L3
-M1
0,75W (PTO)
1 L11 L1
-X4
2 N2 N
3
PE
3
PE
-F1
11 11
-X2
44 44
55
55
55
55
44
44
33
33
-X5
22 22
11
11
66
66
1
2
3 1
2
3
-S5
1
2
3 1
2
3
-S4
BN
BU
YE/GN
BU
BN
BN
BU
YE/GN
BU
BN
-W3
GN
BK
RD
GN
BK
RD
-W2
GY
WH/RD
WH/BN
WH/BK
GY
WH/RD
WH/BN
WH/BK
-W1
/.2
6 66 6
-X3
7 77 7
5 5
5 5
9 9
9 9
8 8
8 8
BK 5
BK 4
BK 3
BK 2
BK 1
PE
S
BK 5
BK 4
BK 3
BK 2
BK 1
PE
S
-W6
S
-X6
BN
BU
YE/GN
BN
BU
BN
BU
YE/GN
BN
BU
-W4
L3
PE
1
4
L2
5
N
L1
L1
PE
+24V
LI4
L3
PE
1
4
L2
5
N
L1
L1
PE
+24V
LI4
-Q1
VT
WH
BN
GY
BK
GNYE
VT
WH
BN
GY
BK
GNYE
-W5
WH/OG
WH/YE
WH/VT
WH/GY
WH/BU
WH/OG
WH/YE
WH/VT
WH/GY
WH/BU
-W1
/.2
3
4
4
5
1
L1
1
2
11
10
N
12
13
7
PE L1N-
9
15
5
14
3
4
4
5
1
L1
1
2
11
10
N
12
13
7
PE L1N-
9
15
5
14
-K1
PCB
1112 1112
-S1
2122 2122
2 2
2 2
-X1
1 11 1
RD
OR
BK
YE
RD
OR
BK
YE
-W1
/.2
/.3
4 44 4
3 3
3 3
2mm2
Wire code, IEC/EN 60757
29-12-2017
29-12-2017
Supply
Plug
Safety guard
magnet aected
Main motor
Bowl switch 2
Bowl switch 1
Modbus rtu rs485
Motor cable
Frequency
Converter
Emergency stop
Communication & safty Motor control
Frequency
Converter boxs
Bowl detection
4 pcs. PE fasteners
in the heatsink plate
FRAME
Shield
Shield
15
Indhold af Overensstemmelseserklæring, (Maskindirektivet, 2006/42/EC, Bilag II, del A) DK
Contents of the Declaration of conformity for machinery, (Machinery Directive 2006/42/EC, Annex II., sub. A) EN
Inhalt der Konformitätserklärung für Maschinen, (Richtlinie 2006/42/EG, Anhang II, sub A) DE
Contenu de la Déclaration de conformité d’une machine, (Directive Machine 2006/42/CE, Annexe II.A) FR
Inhoud van de verklaring van overeenstemming voor machines, (Richtlijn 2006/42/EC, Bijlage II, onder A) NL
Contenido de la declaración de conformidad sobre máquinas, (Directiva 2006/42/EC, Anexo II, sub A) ES
Fabrikant; Manufacturer; Hersteller; Fabricant; Fabrikant; Fabricante: Varimixer A/S
………………………………………………………………….……
Adresse; Address; Adresse; Adresse; Adres; Dirección: Kirkebjerg Søpark 6, DK-2605 Brøndby, Denmark
……………………………………………………………………….
Navn og adresse på den person, som er bemyndiget til at udarbejde teknisk dossier
Name and address of the person authorised to compile the technical file
Name und Anschrift der Person, die bevollmächtigt ist, die technischen Unterlagen zusammenzustellen
Nom et adresse de la personne autorisée à constituer le dossier technique
naam en adres van degene die gemachtigd is het technisch dossier samen te stellen
nombre y dirección de la persona facultada para elaborar el expediente técnico
Navn; Name; Name; Nom; Naam; Nombre: Kim Jensen
……………………………………………………………………….
Adresse; Address; Adresse; Adresse; Adres; Dirección: Kirkebjerg Søpark 6, DK-2605 Brøndby, Denmark
.........................................................................
Sted, dato; Place, date; Ort, Datum; Lieu, date ; Plaats, datum ; Place, Fecha: Brøndby, 14-03-2018
........................................................................
Erklærer hermed at denne røremaskine
Herewith we declare that this planetary mixer
Erklärt hiermit, dass diese Rührmaschine
Déclare que le batteur-mélangeur ci-dessous
Verklaart hiermede dat Menger
Declaramos que el producto batidora
• er i overensstemmelse med relevante bestemmelser i Maskindirektivet (Direktiv 2006/42/EC)
is in conformity with the relevant provisions of the Machinery Directive (2006/42/EC)
konform ist mit den Bestimmungen der EG-Maschinenrichtlinie (Direktiv 2006/42/EG)
Satisfait à l’ensemble des dispositions pertinentes de la Directive Machines (2006/42/CE)
voldoet aan de bepalingen van de Machinerichtlijn (Richtlijn 2006/42/EC)
corresponde a las exigencias básicas de la Directiva sobre Máquinas (Directiva 2006/42/EC)
• er i overensstemmelse med følgende andre CE-direktiver
is in conformity with the provisions of the following other EC-Directives
konform ist mit den Bestimmungen folgender weiterer EG-Richtlinien
Est conforme aux dispositions des Directives Européennes suivantes
voldoet aan de bepalingen van de volgende andere EG-richtlijnen
está en conformidad con las exigencias de las siguientes directivas de la CE
2014/30/EU ; 1935/2004 ; 10/2011 ; 2023/2006 ; RoHS 2011/65/EU , 822/2013 (DK only)
…………………………………………………………………………………………………………………………………………….....
Endvidere erklæres det
And furthermore, we declare that
Und dass
Et déclare par ailleurs que
En dat
Además declaramos que
• at de følgende (dele af) harmoniserede standarder, er blevet anvendt
the following (parts/clauses of) European harmonised standards have been used
folgende harmonisierte Normen (oder Teile/Klauseln hieraus) zur Anwendung gelangten
Les (parties/articles des) normes européennes harmonisées suivantes ont été utilisées
de volgende (onderdelen/bepalingen van) geharmoniseerde normen/nationale normen zijn toegepast
las siguientes normas armonizadas y normas nacionales (o partes de ellas) fueron aplicadas
EN454:2014 ; EN60204-1:2006; EN12100-2011
……………………………………………………………………………………………………………………………………...
EN61000-6-1:2007; EN61000-6-3:2007
……………………………………………………………………………………………………………………………………...
DS/EN 1672-2 + A1:2009
……………………………………………………………………………………………………………………………………...
16
Innehåll i örsäkran om maskinens överensstämmelse, (Maskindirektivet 2006/42/EG, bilaga 2, A) SV
Contenuto della dichiarazione di conformità per macchine, (Direttiva 2006/42/CE, Allegato II, parte A) IT
Sisukord masina vastavusdeklaratsioon , (Masinadirektiiv 2006/42/EÜ, lisa II, punkt A) ET
Treść Deklaracja zgodności dla maszyn (Dyrektywa maszynowa 2006/42/WE, Załącznik II, pkt A) PL
Sisältö vaatimustenmukaisuusvakuutus koneesta (Konedirektiivi 2006/42/EY, Liite II A) FI
Tillverkare; Fabbricante; Tootja; Producent; Valmistaja: Varimixer A/S
………………………………………………………………….……
Adress; Indirizzo; Aadress; Adres;
Osoite: Kirkebjerg Søpark 6, DK-2605 Brøndby, Denmark
……………………………………………………………………….
Namn och adress till den person som är behörig att ställa samman den tekniska dokumentationen:
Nome e indirizzo della persona autorizzata a costituire il fascicolo tecnico
Tehnilise kausta volitatud koostaja nimi ja aadress
Imię i nazwisko oraz adres osoby upoważnionej do przygotowania dokumentacji technicznej
Henkilön nimi ja osoite, joka on valtuutettu kokoamaan teknisen tiedoston
Namn; Nome e cognome; Nimi; Imię i nazwisko;
Nimi: Kim Jensen
……………………………………………………………………….
Adress; Indirizzo; Aadress; Adres; Osoite: Kirkebjerg Søpark 6, DK-2605 Brøndby, Denmark
.........................................................................
Ort och datum; Luogo e data; Koht, kuupäev; Miejscowość, data; Paikka, aika: Brøndby, 14-03-2018
........................................................................
Försäkrar härmed att denna blandningsmaskin
Con la presente si dichiara che questo mixer planetaria
Deklareerime käesolevaga, et Planetaarmikseri
Niniejszym oświadczamy, że mikser planetarny
vakuuttaa, että tämä mikseri tyyppi
• överensstämmer med tillämpliga bestämmelser i maskindirektivet (2006/42/EG)
is è conforme alle disposizioni della Direttiva Macchine (Direttiva 2006/42/CE)
vastab kehtivatele masinadirektiivi (2006/42/EÜ) nõuetele
spełnia wymagania odpowiednich przepisów dyrektywy maszynowej (2006/42/WE)
on konedirektiivin (2006/42/EY) asiaankuuluvien säännösten mukainen
• överensstämmer med bestämmelser i följande andra EG-direktiv
è conforme alle disposizioni delle seguenti altre direttive CE
vastab järgmiste EÜ direktiivide nõuetele
spełnia wymagania przepisów innych dyrektyw WE
on seuraavien muiden EY-direktiivien säännösten mukainen
2014/30/EU; 1935/2004 ; 10/2011 ; 2023/2006 ; RoHS 2011/65/EU ; 822/2013 (DK only)
…………………………………………………………………………………………………………………………………………………….…...
Vi försäkrar dessutom att
e che
Lisaks ülaltoodule deklareerime, et
Ponadto oświadczamy, że
ja lisäksi vakuuttaa, että
• följande (delar/paragrafer av) europeiska harmoniserade standarder har använts
sono state applicate le seguenti (parti/clausole di) norme armonizzate
kasutatud on järgmisi Euroopa harmoniseeritud standardeid (või nende osi/nõudeid)
zastosowano następujące części/klauzule zharmonizowanych norm europejskich
seuraavia eurooppalaisia yhdenmukaistettuja standardeja (tai niiden osia/kohtia) on sovellettu
EN454:2014 ; EN60204-1:2006; EN12100-2011
……………………………………………………………………………………………………………………………………..................
EN61000-6-1:2007; EN61000-6-3:2007
……………………………………………………………………………………………………………………………………...
DS/EN 1672-2 + A1:2009
……………………………………………………………………………………………………………………………………...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Metos Kodiak20 Manuale utente

Metos
Marca
Metos
Modello
Kodiak20
Categoria
Miscelatori
Tipo
Manuale utente
Questo manuale è adatto anche per
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti