Candy CDI 3530/E-80 Manuale utente

Marca: Candy

Modello: CDI 3530/E-80

Categoria: Lavastoviglie

Tipo: Manuale utente

User instructions

CDI 3530

DISHWASHER

Congratulations!

Thank you for choosing a Candy

appliance; quality dishwashers which

guarantee high performance and

reliability.

Candy manufacture a vast range

of domestic appliances: washing

machines, washer/dryers, cookers,

microwave ovens, ovens and hobs,

refrigerators and freezers.

Ask your dealer for the catalogue with

the complete range of Candy products.

Please read this booklet carefully as

it provides important information

regarding the safe installation, use,

and maintenance of the machine,

together with some useful advice on

how to achieve the best results from

your dishwasher.

For future reference please keep this

instruction booklet in a safe place.

CUSTOMER SERVICE AND

GUARANTEE

Your new appliance is fully guaranteed

by the manufacturer for 12 months

against electrical/mechanical break-

down excluding:

A. Any faults which occur due to bad

installation or misuse of the machine.

B. Any faults which occur due to repair

of, or interference with, the machine

by any person not authorised by the

manufacturer to carry out service.

C. Any faults which occur due to

any parts which are fitted to the

machine which are not the original

manufacturers parts.

D. Any faults arising from non-domestic

use or unusual or abnormal use of

the machine.

E. Any faults arising from operation at

incorrect voltage.

F. Any faults arising from incorrect

operation of the machine.

The guarantee applies to Gt Britain

and Northern Ireland only, and is an

addition to your statutory rights.

AFTER SALES SERVICE

For service and repairs call your local engineer on our national telephone number:

GIAS Service Tel: 08444 995599

Support Service (Eire 0818 200021)

CONTENTS

Safety advice

Setting up, installation

Water softener unit

Loading the salt

Adjusting the upper basket

Loading the dishes

Information for test laboratories

Loading the detergent

Types of detergent

Loading the rinse aid

Cleaning the filters

Some practical hints

Routine cleaning and maintenance

Description of the control panel

Technical data

Programme selection and special functions

Programme guide

Identifying minor faults

pag. 4

pag. 5

pag. 8

pag. 9

pag. 10

pag. 11

pag. 13

pag. 14

pag. 15

pag. 16

pag. 17

pag. 18

pag. 19

pag. 20

pag. 21

pag. 24

pag. 26

Please read the instructions in this booklet carefully because they contain important

information on how to install, use and maintain your dishwasher safely as well as

containing useful tips on how to make the most of it.

Keep this booklet safe for future reference.

Fig. A

SAFETY INSTRUCTIONS

There are certain basic safety rules

which are valid for any domestic

appliance.

Installation

■ Make sure that the plug fitted to the

machine is compatible with the power

supply socket. If it is not, get a suitably

qualified person to fit the correct type,

and to make sure that the cables to the

mains socket are able to cope with the

power rating of the appliance.

■ Ensure that the dishwasher does not

crush power cables.

■ In general it is not advisable to use

adaptors, multiple plugs and/or extension

cables.

■ Should it be necessary to replace the

supply cord, call the After Sales Service

Centre.

Safety

■ Never touch the appliance when your

hands or feet are wet or damp.

■ Do not use when your feet are bare.

■ Do not remove the plug from the mains

supply socket by pulling the mains cable

or the machine itself.

■ Do not leave the appliance exposed to

the elements (rain, sun etc).

■ This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities,

or lack of experience and knowledge,

unless they have been given supervision

or instruction concerning use of the

appliance by a person responsible for

their safety.

Children should be supervised to ensure

that they do not play with the appliance.

■ Water left in the machine or on the

dishes at the end of the wash programme

should not be swallowed.

■ The door should not be left in the open

position since this could present a potential

hazard ( es. tripping ).

■ Leaning or sitting on the open door of

the dishwasher could cause it to tip over.

WARNING !

Knives and other utensils with sharp

points must be loaded in the basket

with their points down or placed in a

horizontal position.

Daily use

■ This appliances is intended to be used in

household and similar applications such

as:

- staff kitchen areas in shops, offices

and other working environments;

- farm houses;

- by clients in hotels, motels and other

residential type environments;

- bed and breakfast type environments.

A different use of this appliance from

household environment or from typical

housekeeping functions, as commercial

use by expert or trained users, is excluded

even in the above applications.

If the appliance is used in a manner

inconsistent with this it may reduce the

life of the appliance and may void the

manufacturer’s warranty.

Any damage to the appliance or other

damage or loss arising through use that is

not consistent with domestic or household

use (even if located in a domestic or

household environment) shall not be

accepted by the manufacturer to the fullest

extent permitted by law.

■ The dishwasher is designed for normal

kitchen utensils.

Objects that have been contamined by

petrol, paint, traces of steel or iron,

corrosive chemicals, acids or alkalis

must not be washed in the dishwasher.

■ If there is a water softening device installed

in the home there is no need to add

salt to the water softener fitted in the

dishwasher.

WARNING!

THIS APPLIANCE MUST BE EARTHED.

Fuses and plugs

This appliance should be used only on a

socket with a minimum rating of 13 Amp.

Our ready-fitted plug is already equipped

with a 13 amp fuse which is BS 1362 ASTA

approved.

Any replacement should be exactly the

same.

If the fuse cover is lost, do not use the plug

until it is replaced.

A correct replacement fuse cover (obtainable

from your dealer or Electricity board) must be

the same colour as shown or named on the

insert on the base of the plug.

Manufacturer declines all responsibility

for any damage due to non-earthing of

the machine.

Appliance complies with

European Directives 73/23/EEC

and 89/336/EEC, replaced by

2006/95/EC and 2004/108/EC, and

subsequent amendments.

Green and

yellow wire

Marked with the letter E,

OR marked with the Earth

symbol,

OR coloured green,

OR coloured green and

yellow.

Blue wire

Brown wire

Marked N,

OR coloured black.

Marked L,

OR coloured red.

Connect to the terminal in the plug

INSTALLATION

(Technical notes)

IMPORTANT

When the appliance is located on a

carpet floor, attention must be paid to

ensure that there is no obstruction to

the bottom vents.

Make sure that the plug on the

appliance remains accessible after

installation.

Electrical connection

Plug your dishwasher into the power

socket.

If the plug we supply does not fit :

■ CUT IT OFF AND DESTROY IT!

You can't use it on other appliances, and

the exposed wires could be dangerous if

anyone plugged it in.

■ Fit a suitable plug, as follows:

■ Cutlery is washed best if it is placed in

the basket with the handles downwards.

■ If the appliance breaks down or stops

working properly, switch it off, turn off the

water supply and do not tamper with it.

Repair work should only be carried out

by an approved service agent and only

genuine spare parts should be fitted. Any

failure to follow the above advice may

have serious consequences for the safety

of the appliance.

Disposal

■ The dishwasher has been made from

materials which can be recycled so that it

can be disposed of in an environmentally

friendly way.

■ If you wish to dispose of an old dishwasher

be careful to remove the door to

eliminate the risk of children becoming

trapped inside it.

Water connection

IMPORTANT

The appliance must be connected to

the water mains using new hose-sets.

The old hose-sets should not be reused.

■ The inlet and drain hoses can be directed

to left or right.

IMPORTANT

The dishwasher can be connected to

either cold or hot water, as long as it

is no hotter than 60 °C.

■ Water pressure must be between

0,08 MPa and 0,8 MPa. If the pressure is

below the minimum consult our service

department for advice.

■ The inlet hose must be connected to a

tap so that the water supply can be cut

off when the machine is not in use

(fig. 1 B).

■ The dishwasher is fitted with 3/4" threaded

connector (fig. 2).

■ Connect inlet hose “A” to water tap “B”

with a 3/4" attachment making sure that

it has been properly tightened.

■ If it is necessary, the inlet pipe can be

lengthened up to 2,5 m. The extension

pipe is available from the After Sales

Service Centre.

■ If limescale deposits or sand are present

in the water, it is advisable to obtain the

appropriate filter, art. 9226085, from the

After Sales Service Centre (fig. 3). The

filter “D” must be inserted between the tap

“B” and the inlet hose “A”, remembering

to fit the washer “C”.

■ If the dishwasher is connected to new

pipes or to pipes which have not been in

use for a long time run water through for

a few minutes before connecting the

inlet hose. In this way no deposits of

sand or rust will clog up the water inflow

filter.

Connecting the outlet hose

■ The outlet hose should disharge into a

standpipe, making sure that there are no

kinks (fig. 4).

■ The standpipe must be at least 40 cm

above floor level and it must have an

internal diameter of at least 4 cm.

■ It is advisable to fit an anti-odour air trap

(fig. 4X).

■ If necessary the outlet hose can be

extended up to 2,5 m, provided that it is

kept at a maximum height of 85 cm

above floor level. The extension pipe is

available from the After Sales Service

Centre.

■ The hose can be hooked over the side of

the sink, but it must not be immersed in

water, in order to prevent water from

being syphoned back to the machine

when this is in operation (fig. 4Y).

■ When installing the appliance under a

worktop the hose pipe clamp must be

attached to the wall in the highest possible

position under the worktop (fig. 4Z).

■ Check that there are no kinks in the inlet

and outlet hoses.

Opening the door

If the machine comes open while it is working,

an electrical safety device automatically

switches everything off.

IMPORTANT

For the machine to work properly,

the door should not be opened while

it is in operation.

Closing the door

Place the baskets in the machine.

Make sure that both the spray arms are

free to rotate and are not obstructed by

cutlery, crockery or pans. Close the door,

pressing on it to make sure it is firmly shut.

* The water softener unit is set in the

factory at level 3, as this is suitable for

the majority of users.

According to the degree of hardness of

your water, regulate the softener unit in the

following way:

IMPORTANT

The dishwasher must ALWAYS be

off before start of this procedure.

1. Hold down the FIRST "PROGRAMME"

button (from the right) and at the same

time switch on the dishwasher by

pressing the "ON/OFF" button (a brief

audible signal will sound).

2. Keep the "PROGRAMME" button

pressed for at least 5 seconds, UNTIL

an audible signal sounds. Some

"PROGRAMME SELECTION" indicator

lights will come on to indicate the

current water softener setting level.

3. Press the same button again to select

the required water softener level: each

time the button is pressed, one indicator

light will come on (the water softener

level is indicated by the number of lights

on). For level 5, 4 lights will flash, for

level 0 all lights will be off.

4. Turn off the dishwasher by pressing the

"ON/OFF" button to confirm the new

setting.

WARNING!

If any problem occurs, turn the

dishwasher off by pressing the

"ON/OFF" button and start the

procedure again from the beginning

(STEP 1).

WATER SOFTENER UNIT

Depending on the source of the supply,

water contains varying amounts of limestone

and minerals which are deposited on the

dishes leaving whitish stains and marks.

The higher the level of these minerals

present in the water, the harder the water is.

The dishwasher is fitted with a water

softener unit which, through the use of

special regenerating salt, supplies

softened water for washing the dishes.

The degree of hardness of your water can

be obtained from your water supply

company.

Regulating the water softener

The softener unit can treat water with a

hardness of up to 90°fH (French grading)

or 50°dH (German grading) through 6

different settings.

The table below lists different degrees of

water hardness with the corresponding

setting for the softener unit.

Level

ºfH

(French

grading)

ºdH

(German

grading)

YES

No indicator

lights

Indicator light

Indicator lights

1,2

Indicator lights

1,2,3

Indicator lights

1,2,3,4

Indicator lights

1,2,3,4

flashing

Water

hardness

Water

softener

setting

Use of

regenerating

salt

0-5

6-15

16-30

31-45

46-60

61-90

0-3

4-9

10-16

17-25

26-33

34-50

“PROGRAMME” buttons

“ON/OFF” button

“PROGRAMME SELECTION” indicator lights

LOADING THE SALT

■ On the bottom of the machine there is a

container for the salt for regenerating

the softener.

■ It is important to use only a salt that is

specifically designed for dishwasher.

Other types of salt contain small quantities

of insoluble particles which over a long

period of time may affect and deteriorate

the softener performance.

■ To add salt, unscrew the cap of the con-

tainer on the bottom and then refill the

container.

■ During this operation a little water will

overflow; but keep adding salt until the

container is full. When the container is

full, clean the thread of salt residue and

retighten the tap.

■ After loading the salt, it is recommended

running a complete washing cycle,

or COLD RINSE programme. The salt

dispenser has a capacity of between 1.5

and 1.8 kg and, for efficient use of the

appliance, it should be refilled from time

to time according to the regulation of the

water softener unit.

IMPORTANT

(Only for first start up)

When the appliance is used for the

first time, after completely filling the

salt container, it is necessary to add

water until the container overflows.

Salt loading indicator

This model is provided with an indicator light

on the control panel which will light up

when it is necessary to reload the salt

container.

IMPORTANT

The appearance of white stains on

dishes is generally an important

sign that the salt container needs

filling.

ADJUSTMENT OF THE

UPPER BASKET

If 29 cm to 32,5 cm plates are normally

used, load them onto the lower basket after

the upper basket has been placed in its

upper position and proceed as detailed

below:

1. Pull out the upper basket;

2. Then grasp the basket from both sides

and lift it upwards (fig. 1).

Dishes that are bigger than 14 cm in

diameter can no longer be loaded onto the

upper basket and the mobile supports

cannot be used when the basket is in the

upper position.

ADJUST BASKET TO THE LOWER

POSITION:

1. Grasp the basket from both sides and lift

slightly upwards (fig. 2a);

2. Then slowly release into the correct

position (fig. 2b).

N. B. : NEVER LIFT OR LOWER THE

BASKET BY ONE SIDE ONLY (fig.3).

Attention :

it is advisable to adjust the basket before

loading the dishes.

BB1

AA1

A standard daily load is represented in

figs. 1 and 2.

Upper basket (fig. 1)

Upper basket (fig. 2)

Using the lower basket

■ Saucepans, oven dishes, tureens, salad

bowls, lids, serving dishes, dinner plates

and soup plates can be loaded into the

lower basket.

■ Place the cutlery in the plastic cutlery

holder with the handles pointing upwards

and place the cutlery holder on the lower

basket (fig. 6) making sure that the

cutlery does not get in the way of the

rotating arms.

LOADING DISHES

Using the upper basket

■ The upper basket is provided with

mobile racks hooked to the sides of the

basket, which can be regulated into 4

positions.

■ In the lowered position (A-A1) the racks

may be used for such items as: tea and

coffee cups, kitchen knives and ladles.

Also glasses with stems may be safely

hung on the ends of the racks.

■ In the upright position (B-B1) the racks

allow you to load dinner plates and soup

plates up to a maximum diameter of 19

cm. Plates should be loaded vertically

with the underside of the plate towards

the back of the dishwasher with a space

between each plate to allow water to

pass freely.

■ It is advisable to load large plates slightly

tilted towards the front to facilitate the

introduction of the basket into the

machine.

■ The upper basket has been designed to

offer maximum flexibility in use and can

be loaded with glasses, cups, small

plates and small-sized bowls.

■ The lower basket is fitted with a special

adjustable central rack (fig. 3 and 4).

This permits stable and optimum

loading, even when the size and/or

shape of the dishes is non-standard.

- POSITION “A”: for a standard load, or

one that excludes pans, salad bowls and

the like.

- POSITION “B”: for dishes which,

although standard size, have a particular

shape (very deep bowls, square dishes

or ones without borders etc.).

- POSITION “C”: for larger than average

flat plates and/or ones with non-

standard shapes (square, hexagonal,

oval, pizza dishes etc.).

■ Smaller plates (used for dessert plates

for example), can also be placed into the

lower basket as shown in the figure 5,

with the support flap placed outwards

("B").

For normal or large plates the flap must

be in the position ("A").

WARNING!

If the small plates are placed in the

basket with the support flap in the

incorrect position, the plates will

interfere with the lower spraying arm

preventing it to rotate.

A standard daily load is represented in

fig. 6.

Lower basket (fig. 6)

Please load the dishwasher sensibly to

ensure the best wash results.

IMPORTANT

The lower basket has a safety-stop

device, for its safe extraction, also

especially useful with a full load.

For loading salt, cleaning filter and for

ordinary maintenance, the complete

extraction of the basket is necessary.

Cutlery basket

The top of cutlery basket can be removed,

for enable various loading options.

Using the third basket

■ The third basket has been designed to

load items such as utensils of small

dimensions or flat and long shaped

items. By freeing the lower baskets from

these objects, loading big-size items

becomes more comfortable and easier,

making it possible for instance to load

plates and pots in the lower basket.

■ The third basket can be loaded with the

following items: coffee cups and side

plates, fruit or dessert cups, small bowls,

saucers, kitchen knives and forks, ladles

and large spoons, graters, and

accessories for small appliances (e.g.

food mixer blades).

ATTENTION!

The third basket is NOT designed for

loading cutlery. The absence of racks

for fixing cutlery could involve such

items being found in the lower

baskets.

■ In order to obtain optimum washing

results, it is advisable to load items with

their underside towards the ceiling of the

dishwasher (e.g. small plates and

bowls).

■ The third basket can be easily extracted

from the dishwasher, by removing the

front stops at the beginning of basket

tracks.

■ The third basket has been designed to

offer maximum flexibility in use. Due to

its partition in three tilted sections and

absence of fixed racks, it can be loaded

in numerous ways: only coffee cups and

side plates; or coffee cups mixed with

bowls and utensils; or again with side

plates, graters, and spoons.

A standard daily load is represented in

fig. 7.

Third basket (fig. 7)

INFORMATION FOR THE TEST

LABORATORIES

Please ask information required for

comparison testing and measuring noise

levels, according to EN normative, to the

following address:

testinfo-dishwasher@candy.it

In the request, please specify model name

and number of the dishwasher (see rating

plate).

LOADING THE DETERGENT

The detergent

IMPORTANT

It is essential to use a detergent

that is specifically designed for

dishwashers either in powder, liquid

or tablet form.

“FINISH” gives very good results and can

be easily obtained.

Unsuitable detergents (like those for

washing up by hand) do not contain the

proper ingredients for use in a dishwasher,

and stop the dishwasher from working

correctly.

Filling the detergent container

The detergent container is inside the door

(fig. A “2”). If the lid of the container is

closed, press the button (A) to open.

At the end of every wash cycle the lid is

always open and ready for the next time

the dishwasher is used.

WARNING!

When loading the lower basket, please

ensure that the plates or others do not

obstruct the detergent dispenser.

The amount of detergent to be used varies

according to how dirty the dishes are and

on the type of dishes to be washed.

We advise using 20÷30 g of detergent in the

wash section of detergent compartment (B).

After pouring the detergent into the container,

close the lid, firstly pushing (1) and then

pressing on it (2) until you hear the click.

Since not all detergents are the same the

instructions on the boxes of detergent can

vary. We should just like to remind users

that too little detergent does not clean the

dishes properly whilst too much detergent

will not produce better results and is also a

waste.

IMPORTANT

Do not use an excessive amount of

detergent and help limit damage to

the environment at the same time.

TYPES OF DETERGENT

Detergent tablets

Detergent tablets of different manufacturers

dissolve at different speeds, for this

reason, during short programmes, some

detergent tablets may be not fully effective,

because they are not completely dissolved.

If these products are used, is recommended

to choose longer programmes to guarantee

the complete use of the detergent.

IMPORTANT

To get satisfactory washing results,

the tablets MUST be placed in the

wash section of the detergent

container and NOT directly in the

tub.

Concentrated detergents

The concentrated detergents, with reduced

alkalinity and with natural enzymes, in

conjunction with 50°C wash programmes,

have a smaller impact on the environment

and they protect the dishes and the

dishwasher.

The 50°C wash programmes purposely

exploit the dirt-dissolving properties of the

enzymes, allowing therefore, with the use

of the concentrated detergents, to achieve

the same results of the 65°C programmes

but at a lower temperature.

Combined detergents

The detergents that also contain the rinse

aid must be placed in the wash section of

the detergent container. The rinse aid

container must be empty (if it is not empty,

set the rinse aid regulator to lowest position

before using combined detergents).

"ALL in 1" combined detergents

If you are planning to use “ALL in 1” (“3 in 1 “/

“4 in 1”/ “5 in 1”, etc.) combined detergents i.e.

those with built in salt and/or rinse agent,

we would advise the following:

■ read carefully and follow the manufacturer’s

instructions given on the packaging;

■ the effectiveness of detergents containing

the built in water softener/salt depends

on the hardness of your water supply.

Check that the hardness of your water

supply is within the effective range given

on the detergent packaging.

If when using this type of product, you

don't get satisfactory washing results,

please contact the detergent

manufacturer.

In certain circumstances use of combined

detergents can cause:

■ limescale deposits on dishes or in the

dishwasher;

■ a reduction in washing and drying

performance.

IMPORTANT

Any problems which arise as a direct

result of the use of these products

are not covered by our warranty.

Please note that using the "ALL in 1"

combined detergents, the rinse aid and

salt indicator lights (only used on

selected models) are superfluous, so you

must ignore the lights.

If washing and/or drying problems occur,

we recommend you return to use traditional

separate products (salt, detergent and

rinse agent). This will ensure that the water

softener in the dishwasher operates

correctly.

In this case, we recommends that you:

■ refill both the salt and rinse aid container;

■ run one normal washing cycle without a

load.

Please note that on return to the use of

conventional salt, a number of cycles will

be required before the system becomes

fully efficient again.

LOADING THE RINSE AID

The rinse aid

The rinse aid, which is automatically

released during the last rinsing cycle, helps

the dishes to dry quickly and prevents

spots and stains forming.

Filling the rinse aid container

The rinse aid container can be found to the

left of the detergent container (fig. A "3").

To open the lid, push the reference mark

and, in the same time, pull the tab of

opening.

It is always advisable to use rinse aid that

is specifically designed for dishwasher.

Check the rinse aid level through the

indicator eye (C) which is located on the

dispenser.

Regulating the rinse aid from 1 to 6

The regulator (D) is placed under the lid

and can be turned using a coin.

The recommended position is 4.

The limestone content of the water

considerably affects the formation of

limescale and the drying performance.

It is therefore important to regulate the

quantity of rinse aid to achieve good

washing results.

If, after the wash, streaks occur on the

dishes, decrease the amount by one

position. If whitish spots occur, increase the

amount by one position.

FULL EMPTY

dark light

CLEANING THE FILTERS

The filter system (fig.A “4”) consists of:

a central container that traps the larger

particles;

a flat gauze that continuously filters the

wash water;

a micro filter, located beneath the gauze,

that traps the tiniest particles ensuring a

perfect rinse.

■ To achieve excellent results every time,

the filters should be checked and

cleaned after each wash.

■ To remove the filter unit, simply turn the

handle anticlockwise (fig. 1).

■ For ease of cleaning, the central container

is removable (fig. 2).

■ Remove the gauze filter (fig.3) and

wash the whole unit under a jet of

water. If necessary a small brush can

be used.

■ With the Self-cleaning Micro filter,

maintenance is reduced and the filter

unit need only be checked every two

weeks. Nevertheless, after each wash it

is advisable to check that the central

container and the gauze filter are not

clogged.

WARNING!

After cleaning the filters, make sure

that they are correctly reassembled

and that the gauze filter is properly

positioned at the bottom of the

dishwasher.

Make sure that the filter is screwed

back, clockwise, into the gauze, as

poor seating of the filter unit could

have an adverse effect on the

efficiency of the appliance.

IMPORTANT

Never use the dishwasher without

the filters.

PRATICAL HINTS

How to get really good wash

results

■ Before placing the dishes in the

dishwasher, remove any remaining

food (bones, shells, pieces of meat or

vegetables, coffee grounds, skin of fruit,

cigarette ash, tooth picks etc. to avoid

blocking the filters, water outlet and

washing arm nozzles.

■ Try not to rinse the dishes before

loading them into the dishwasher.

■ If saucepans and oven dishes are

encrusted with the remains of burnt or

roast food, it is advisable to leave them

to soak before washing.

■ Place the dishes face downwards.

■ Try to place the dishes in such a way

that they are not touching one another.

If they are loaded properly you will get

better results.

■ After loading the dishes check that the

washing arms can rotate freely.

■ Pans and other dishes that have

particularly stubborn food particles or

remnants of burnt food should be left to

soak in water with dishwasher

detergent.

■ To wash silver properly:

a) rinse the silver immediately after

use, especially if it has been used for

mayonnaise, eggs, fish etc.;

b) do not sprinkle detergent onto it;

c) keep it separate from other metals.

How to make savings

■ If you want the dishwasher to give a

complete wash, place the dishes in the

dishwasher at the end of each meal and

if necessary turn on the COLD RINSE

cycle to soften the food remains and

remove bigger particles of food from the

new load of dishes.

When the dishwasher is full start the

complete wash cycle programme.

■ If the dishes are not very dirty or if the

baskets are not very full select an

ECONOMY programme, following the

instructions in the program list.

What not to wash

■ It should be remembered that not all

dishes are suitable for washing in a

dishwasher.We advise against using

the dishwasher to wash items in

thermoplastic, cutlery with wooden or

plastic handles, saucepans with

wooden handles, items in aluminium,

crystal, leaded glass unless otherwise

stated.

■ Certain decorations may fade. It is

therefore a good idea before loading the

whole batch to wash just one of the

items first so as to be sure that others

like it will not fade.

■ It is a good idea not to put silver cutlery

with non-stainless steel handles into

the dishwasher as there could be a

chemical reaction between them.

IMPORTANT

When buying new crockery or

cutlery always make sure that they are

suitable for washing in a dishwasher.

Useful hints

■ In order to avoid any dripping from the

top rack, remove the lower rack first.

■ If the dishes are to be left in the

machine for some time, leave the door

ajar, to let some air circulate and to

improve the drying performance.

WHEN CYCLE IS FINISHED

After every wash it is essential to turn off

water supply and to switch off the machine

by pressing the On/Off button to the off

position.

If the machine is not going to be used for

some time, it is advisable to follow these

rules:

1. do an empty wash with detergent in order

to clean the machine of any deposits;

2. pull out the electric plug;

3. turn off the water tap;

4. fill the rinse aid container;

5. Ieave the door ajar;

6. keep the inside of the machine clean;

7. If the machine is left in places where the

temperature is below 0°C any water left

inside the pipes may freeze. Wait until

the temperature rises above zero and

then wait for about 24 hours before

starting up the dishwasher.

CLEANING AND

MAINTENANCE

■ To clean the dishwasher outside, do not

use solvents (degreasing action) neither

abrasives, but only a cloth soaked with

water.

■ The dishwasher does not require special

maintenance, because the tank is

self-cleaning.

■ Regularly wipe the door gasket with a

damp cloth to remove any food remains

or rinse aid.

■ It is advisable to remove limestone

deposits or dirt periodically, by doing an

empty wash; pour a glass of vinegar on

the bottom of the tank and select the

light wash.

■ If, in spite of the routine cleaning of the

filters, you notice that the dishes or pans

are not properly washed or rinsed, check

that all the spray heads on the rotor

arms (fig. A “5”) are clear.

If they are blocked, clean them in the

following way:

1. to remove the upper rotor arm, turn it

until it lines up with the stop marked

by the arrow (fig. 1). Push it upwards

(fig. 1b) and, keeping it pushed in,

unscrew it in a clockwise direction

(to reassemble it repeat the same

operation, but turn it anticlockwise).

The lower rotor arm can be removed

simply by pulling it upwards (fig. 2);

2. wash the rotor arms under a jet of water

to clear any blockage in the spray

heads;

3. when you have finished, refit the rotor

arms in the same position, remembering

to re-align the arrow and screw into

position.

■ Both the door lining and the tank lining

are in stainless steel; however, should

spots caused by oxidation occur, this is

probably due to a high level of iron salts

presents in the water.

■ The spots can be removed with a mild

abrasive agent; never use chlorine

based materials, steel wool, etc.

DESCRIPTION OF THE CONTROL PANEL

A "ON/OFF" button

PROGRAMME DESCRIPTION

"PROGRAMME" buttons

"HALF LOAD" option button

"DELAY START" button

F "PROGRAMME STATUS" lights/

"DELAY START" time lights

"OPTION SELECTION" light

"PROGRAMME SELECTION" lights

"SALT EMPTY" light

DIMENSIONS

TECHNICAL DATA

CONSUMPTION (main programmes)*

Programme Energy (kWh) Water (L)

UNIVERSAL

HYGIENIC

ECO

RAPID 32'

Width x Height x Depth (cm)

Depth with door open (cm)

EN 50242 place load

Capacity with pans and dishes

Water supply pressure (MPa)

Fuse / Power input / Supply voltage

9 persons

Min. 0,08 - Max. 0,8

See rating plate

Power consumption of the off-mode and of the left-on mode: 0,10 W / 0,60 W

*Values are measured in a laboratory according to European Standard EN 50242 (consumption may

vary according to conditions of usage).

59,8 x 82 ÷ 90 x 55

117

1,55

2,10

1,06

0,73

La pagina sta caricando ...

Candy CDI 3530/E-80 Manuale utente

Marca: Candy

Modello: CDI 3530/E-80

Categoria: Lavastoviglie

Tipo: Manuale utente

Scarica il pdf

rapporto

Candy CDI 3530/E-80 Manuale utente

Candy CDI 3530/E-80 Manuale utente

Documenti correlati

Altri documenti