Hitachi WR 14DM Handling Instructions Manual

Marca: Hitachi

Modello: WR 14DM

Tipo: Handling Instructions Manual

Cordless Impact Wrench

Akku-schlagschrauber

Cle a choc a batterie

Avvitatore a percussione a batteria

Snoerloze slagmoeraanzetter

Llave de impacto a batería

Chave de impacto a bateria

ªÔ˘ÏÔÓÔÎÏÂÈ‰Ô Ì·Ù·ÚÈ·Û

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste istruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer

cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

408

Code No. C99128871 N

Printed in Japan

Hitachi Koki Co., Ltd.

Variable speed

WR 14DM

123

6 7

8 9

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product is in conformity with standards or standard-

ized documents EN50144 and EN55014-2 in accordance

with Council Directives 89/336/EEC and 98/37/EC.

This declaration is applicable to the product affixed CE

marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses

Produkt den Standards oder standardisierten

Dokumenten EN50144 und EN55014-2 in

Übereinstimmung mit den Direktiven des Europarats

89/336/EWG und 98/37/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung

tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-

sabilité que ce produit est conforme aux normes ou

documents normalisés EN50144 et EN55014-2 en accord

avec les Directives 89/336/CEE et 98/37/CE du Conseil.

Cette déclaration s’applique aux produits désignés CE.

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo

prodotto è conforme agli standard o ai documenti

standardizzati EN50144 e EN55014-2 conforme alle

direttive 89/336/CEE e 98/37/CE del concilio.

Questa dichiarazione è applicabile ai prodotti cui sono

applicati i marchi CE.

Representative office in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head office in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

31. 8. 2004

K. Kato

Board Director

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit

produkt conform de richtlijnen of gestandardiseerde

documenten EN50144 en EN55014-2 voldoet aan de

eisen van EEG Bepalingen 89/336/EEG en 98/37/EC.

Deze verklaring is van toepassing op produkten

voorzien van de CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que

este producto está de acuerdo con las normas o con

los documentos de normalización EN50144 y EN55014-

2 según indican las Directrices del Consejo 89/336/CEE

y 98/37/CE.

Esta declaración se aplica a los productos con marcas

de la CE.

Português

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade,

que este produto está de acordo com as normas ou

documentos normativos EN50144 e EN55014-2 em

conformidade com as Diretrizes 89/336/CEE e 98/37/CE

do Conselho.

Esta declaração se aplica aos produtos designados CE.

Ελληνικά

EK ∆ΗΛΩΣΗ ΕΝΑΡΜΝΙΣΜΥ

∆ηλώνυµε µε απ'λυτη υπευθυν'τητα 'τι αυτ' τ

πρι'ν είναι εναρµνισµέν µε τα πρ'τυπα ή τα

έγρα)α πρτύπων EN50144 και EN55014-2 σε

συµ)ωνία µε τις δηγίες τυ Συµυλίυ 89/336/EOK

και 98/37/EK.

Αυτή η δήλωση ισύει στ πρι'ν µε τ σηµάδι EC.

(A)

(B)

Cordless Impact Wrench

Akku-schlagschrauber

Cle a choc a batterie

Avvitatore a percussione a batteria

Snoerloze slagmoeraanzetter

Llave de impacto a batería

Chave de impacto a bateria

ªÔ˘ÏÔÓÔÎÏÂÈ‰Ô Ì·Ù·ÚÈ·Û

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste istruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer

cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

408

Code No. C99128871 N

Printed in Japan

Hitachi Koki Co., Ltd.

Variable speed

WR 14DM

123

6 7

8 9

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product is in conformity with standards or standard-

ized documents EN50144 and EN55014-2 in accordance

with Council Directives 89/336/EEC and 98/37/EC.

This declaration is applicable to the product affixed CE

marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses

Produkt den Standards oder standardisierten

Dokumenten EN50144 und EN55014-2 in

Übereinstimmung mit den Direktiven des Europarats

89/336/EWG und 98/37/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung

tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-

sabilité que ce produit est conforme aux normes ou

documents normalisés EN50144 et EN55014-2 en accord

avec les Directives 89/336/CEE et 98/37/CE du Conseil.

Cette déclaration s’applique aux produits désignés CE.

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo

prodotto è conforme agli standard o ai documenti

standardizzati EN50144 e EN55014-2 conforme alle

direttive 89/336/CEE e 98/37/CE del concilio.

Questa dichiarazione è applicabile ai prodotti cui sono

applicati i marchi CE.

Representative office in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head office in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

31. 8. 2004

K. Kato

Board Director

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit

produkt conform de richtlijnen of gestandardiseerde

documenten EN50144 en EN55014-2 voldoet aan de

eisen van EEG Bepalingen 89/336/EEG en 98/37/EC.

Deze verklaring is van toepassing op produkten

voorzien van de CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que

este producto está de acuerdo con las normas o con

los documentos de normalización EN50144 y EN55014-

2 según indican las Directrices del Consejo 89/336/CEE

y 98/37/CE.

Esta declaración se aplica a los productos con marcas

de la CE.

Português

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade,

que este produto está de acordo com as normas ou

documentos normativos EN50144 e EN55014-2 em

conformidade com as Diretrizes 89/336/CEE e 98/37/CE

do Conselho.

Esta declaração se aplica aos produtos designados CE.

Ελληνικά

EK ∆ΗΛΩΣΗ ΕΝΑΡΜΝΙΣΜΥ

∆ηλώνυµε µε απ'λυτη υπευθυν'τητα 'τι αυτ' τ

πρι'ν είναι εναρµνισµέν µε τα πρ'τυπα ή τα

έγρα)α πρτύπων EN50144 και EN55014-2 σε

συµ)ωνία µε τις δηγίες τυ Συµυλίυ 89/336/EOK

και 98/37/EK.

Αυτή η δήλωση ισύει στ πρι'ν µε τ σηµάδι EC.

(A)

(B)

10 11

2 92

12 13

14 15

16 17

18 19

3mm

11.5mm

10 11

2 92

12 13

14 15

16 17

18 19

3mm

11.5mm

English Deutsch Français Italiano

14.4 V Rechargeable

Akkumulator, 14,4 V

Batterie rechargeable,

battery 14,4 V

Latch Schnapper Loquet

Handle Griff Poignée

Insert Einsatz Insérer

Pull out Herausziehen Tirer

Insert Einsetz Insérer

Pilot lamp Kontrollampe Lampe pilote

Hole for connecting the Anschlußlon für

Orifice de raccordement

rechargeable battery Akkumulator

de la batterie rechargeable

Hexagonal socket Sechskantbuchse Douille hexagonal

Groove Schlitz Rainure

Anvil Schabotte Chabotte

Pin Stift Goupille

Ring Ring Aunneau

Hole Öffnung Orifice

Plunger Preßkolben Piston

Hook Haken Crochet

Spring Feder Ressort

Larger diameter faces Der große Durchmesser Gros diamètre dirigé

away weist zur anderen Seite vers l’extérieur

Switch Schalter Interrupteur

Phillips-head screwdriver

Kreuzschlitzschrauben-

Tournevis à tête Phillips

zieher

Screw Schraube Vis

Arrow Pfeil Flèche

Hook cover Hakenabdeckung Cache de crochet

Indentation Einkerbung Entaille

Protuberance Vorsprung Saillie

AAAA batteries Batterien der AAAA Piles AAAA

Push button Druckknopf Poussoir

Push Drücken Pousser

Wear limit Verschließgrenze Limite d'usure

Nail of carbon brush Klaue der Kohlebürste

Clou de balai en

carbone

Protrusion of carbon Krempe der Saillie de balai en

brush Kohlebürste carbone

Contact portion outside Kontaktteil außerhalb

Section de contact à

brush tube des Bürstenrohrs

l’extérieur du tube de balai

Batteria ricaricabile,

14,4 V

Fermo

Impugnatura

Inserire

Estrarre

Inserire

Spia

Foro di collegamento

della batería recargable

Chiave de incavo

esagonale

Scanalature

Basamento

Spina

Anello

Foro

Stantuffo

Grancio

Molla

Diametro più grande

lontano da sé

Interruttore

Cacciavite con testa a

croce

Vite

Freccia

Coperchio gancio

Tacca

Sporgenza

Pile AAAA

Taste da premere

Spingere

Limite di usura

Chiodo di spazzola di

carbone

Sporgenza di spazzola

di carbone

Parte di contatto fuori

dal tubo spazzola

Nederlands Español Português Ελληνικά

Oplaadbare batterij, Batería recargable,

14,4V 14,4V

Vergrendeling Enganche

Handgreep Mango

Insteken Insertar

Uittrekken Sacar

Insteken Insertar

Kontrolelampje Lámpara piloto

Aansluiting voor Agujero para conectar

oplaadbare batterij la batería recargable

Zeschoekige bus Recaptáculo hexanogal

Groef Ranura

Draaistuk Yunque

Pen Pasador

Ring Anillo

Opening Orificio

Plunjer Embolo

Haak Gancho

Veer Resorte

De grotere diameter

El diámetro más

wijst van u vandaan

grande queda en

dirección opuesta

Schakelaar Interruptor

Kruiskopschroevendraaier

Destornillador con

cabeza Phillips

Schroef Tornillo

Pijl Flecha

Afdekking haak Cubierta del gancho

Inkeping Indentación

Uitsteeksel Saliente

AAAA batterijen Pilas AAAA

Druktoets Pulsador

Drukken Presionar

Slijtagegrens Límite de uso

Nagel van koolborstel

Uña de escobilla de

carbón

Uitsteeksel van Saliente de escobilla

koolborstel de carbón

Contact-gedeelte

Tubo exterior de la

buiten de borstelbuis

parte de contacto de

la escobilla de carbón

Bateria de 14,4 V

recarregável

Lingüeta

Cabo

Inserir

Retirar

Inserir

Lâmpada piloto

Orifício para conectar a

bateria recarregável

Encaixe longo

Ranhura

Bigorna

Pino

Anel

Orifício

Pistão

Gancho

Mola

O diâmetro maior dá

para fora

Comutador

Chave Phillips

Parafuso

Seta

Tampa do gancho

Entalhe

Protuberância

Pilhas AAAA

Interruptor

Apertar

Limite de desgaste

Prego da escova de

carvão

Saliência da escova de

carvão

Segmento de contato

no exterior do tubo da

escova

14,4 V Επαναρτιµενη

µπαταρία

Μάνδαλ

ερύλι

Εισωρήστε

Βραήτε έω

Εισωρήστε

∆κιµαστική λάµπα

Τρύπα για την σύνδεση

της επαναρτιµενης

µπαταρίας

Μακριά υπδή

Αυλάκωση

Άκµνας

Πείρς

∆ακτύλις

Τρύπα

Έµλ

Άγκιστρ

Ελατήρι

Η µεγαλύτερη

διάµετρς λέπει πρς

άλλη κατεύθυνση

∆ιακπτης

Κατσαίδι κεαλής

Phillips

Βίδα

Βέλς

Κάλυµµα αγκίστρυ

Αυλάκωση

Πρεή

ΑΑΑΑ µπαταρίες

Κυµπί ώθησης

Σπρώε

.ρι θράς

Καρί καρυνακιύ

Πρεή

καρυνακιύ

Τµήµα επαής έω

απ τ σωλήνα της

ψήκτρας

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite accidents.

2. Avoid dangerous environment. Don’t expose power

tools and charger to rain. Don’t use power tools

and charger in damp or wet locations. And keep

work area well lit. Never use power tools and

charger near flammable or explosive materials.

Do not use tool and charger in presence of

flammable liquids or gases.

3. The appliance is not intended for use by young

children or infirm persons without supervision.

Young children should be supervised to ensure

that they do not play with the appliance. All visitors

should be kept safe distance from work area.

4. Store idle tools and charger. When not in use,

tools and charger should be stored in dry, high

or locked-up place-out of reach of the children and

infirm persons. Store tools and charger in a place

where the temperature is less than 40°C.

5. Don’t force tool. It will do the job better and safer

at the rate for which it was designed.

6. Use right tool. Don’t force small tool or attachment

to do the job of a heavy duty tool.

7. Wear proper apparel. Do not wear loose clothing

or jewelry. They can be caught in moving parts.

Rubber gloves and non-skid footwears are

recommended when working outdoor.

8. Use eye protection with most tools. Also use face

or dust mask if cutting operation is dusty.

9. Don’t abuse cord. Never carry charger by cord or

yank it to disconnect from receptacle. Keep cord

from heat, oil and sharp edges.

10. Secure work. Use clamps or a vise to hold work.

It’s safer than using your hand and it frees both

hands to operate tool.

11. Don’t overreach. Keep proper footing and balance

at all times.

12. Maintain tools with care. Keep tools sharp at all

times, and clean for best and safest performance.

Follow instructions for lubricating and changing

accessories.

13. When the charger is not in use, or when being

maintained and inspected, disconnect its power

cord from the receptacle.

14. Remove chuck wrenches and wrenches. Form habit

of checking to see that wrenches are removed

from tool before turning it on.

15. Avoid accidental starting. Don’t carry tool with

finger on switch.

16. To avoid danger, always use only the specified

charger.

17. Use only genuine HITACHI replacement parts.

18. Do not use power tools for applications other than

those specified in the Handling Instructions.

19. To avoid personal injury, use only the accessories

or attachment recommended in these handling

instructions or in the HITACHI catalog.

20. Let only the authorized service center do the

repairing. The Manufacturer will not be responsible

for any damages or injuries caused by repair by

the unauthorized persons or by mishandling of

the tool.

21. To ensure the designed operational integrity of

power tools and charger, do not remove installed

covers or screws.

22. Always use the charger at the voltage specified

on the nameplate.

23. Do not touch movable parts or accessories unless

the power source has been disconnected.

24. Always charge the battery before use.

25. Never use a battery other than that specified. Do

not connect a usual dry cell, a rechargeable battery

other than that specified or a car battery to the

power tool.

26. Do not use any transformer that has a booster.

27. Do not charge the battery from an engine electric

generator or DC power supply.

28. Always charge indoors. Because the charger and

battery heat slightly during charging, charge the

battery in a place not exposed to direct sunlight;

where the humidity is low and the ventilation is

good.

29. Before starting to work in a high place, pay

attention to the activities below to make sure

there are no people below.

30. Use the exploded assembly drawing on this

handling instructions only for authorized servicing.

31. If the supply cord is damaged, it must be replaced

by the manufacture or its service agent or a

similarly qualified person in order to avoid a

hazard.

PRECAUTIONS FOR CORDLESS IMPACT

WRENCH

1. This is a portable tool for tightening and loosening

bolts and nuts. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. Check that the socket is not cracked or broken.

Broken or cracked sockets are dangerous. Check

the socket before using it.

5. Secure the socket with the socket pin and the ring.

If the socket pin or ring securing the socket is

damaged, the socket may come off from the impact

wrench, which is quite dangerous. Do not use

socket pins or rings that are deformed, worn out,

cracked, or in any other way damaged. Always

make sure to install the socket pin and ring in

the correct position.

6. Check the tightening torque.

The appropriate torque for tightening a bolt

depends on the material the bolt is made of, its

dimensions, grade, etc.

Also, the tightening torque generated by this

impact wrench depends on the materials and

dimensions of the bolt, how long the impact

wrench is applied for the way in which the socket

is installed, etc.

Also the torque when the battery has just been

charged and when it is about to run out are

slightly different. Use a torque wrench to check

that the bolt has been tightened with the

appropriate torque.

7. Stop the impact wrench before switching the

direction of rotation. Always release the switch

and wait for impact wrench to stop before

switching the direction of rotation.

8. Never touch the turning part.

Do not allow the turning socket section to get near

your hands or any other part of your body. You

could be cut or caught in the socket. Also, be

careful not to touch the socket after using

continuously it for a long time. It gets quite hot

and could burn you.

9. Never let the impact wrench turn without a load

when using the universal joint.

If the socket turns without being connected to a

load, the universal joint causes the socket to turn

wildly.

English

You could get hurt or the movement of the socket

could shake the impact wrench so much as to

make you drop it.

10. Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

11. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

12. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

13. Never disassemble the rechargeable battery and

charger.

14. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great

electric current and overheat. It results in burn or

damage to the battery.

15. Do not dispose of the battery in fire.

If the battery burnt, it may explode.

SPECIFICATIONS

POWER TOOL

16. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

17. Bring the battery to the shop from which it was

purchased as soon as the post-harging battery life

becomes too short for practical use. Do not dispose

of the exhausted battery.

18. Using an exhausted battery wil damage the

charger.

MODEL

WR14DM: with charger and case

Model WR14DM

No-load speed 0 – 2300 min

–1

(/min)

Angle driver 12.7 mm

Capacity M10 – M16 (Ordinary bolt)

M8 – M14 (High tension bolt)

Tightening torque

Rechargeable battery EB14B Ni-Cd battery, 14.4 V

(2.0 Ah, 12 cells)

EB1430H Ni-MH battery, 14.4 V

(3.0 Ah, 12 cells)

Weight 1.9 kg

Maximum 200 N·m {2040 kgf·cm}

Tightening is M16 (F10T), when fully charged at 20°C temp.

Tightening time: 3 sec.

CHARGER

Model UC14YFA

Charging time EB14B: Approx. 50 min. (at 20°C)

EB1430H: Approx. 70 min. (at 20°C)

Charging voltage 7.2 – 14.4 V

Weight 0.6 kg

English

STANDARD ACCESSORIES

1. Charger (UC14YFA) ................................................... 1

2. Plastic case ................................................................ 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES

(Sold separately)

1. Sockets

Form B Form C

Form D

Code No.

High ISO ISO Inch

Form

tension

(ordinary)

(small) bolts L L1 øF

10 mm 944291 M6 10 B 40 8 18

12 mm 873632 M8 W5/16" 12 B 40 8 20

13 mm 873539 M8 13 B 40 9 25

14 mm 873540 M10 14 B 40 9 25

12.7

Hexagonal

17 mm 873536 M10 M12 W3/8" 17 C 32 8 28

Socket

19 mm 873624 M12 M14 W7/16" 19 C 34 9 28

21 mm 873626 W1/2" 21 D 36 10 32

22 mm 873627 M12 M14 M16 22 D 40 14 35

24 mm 873629 M16 M18 24 D 40 15 38

26 mm 873630 W5/8" 26 D 40 15 38

27 mm 985195 M16 M18 M20 27 D 40 16 42

Square

head drive

dimensions

S (mm)

Part Name

Suitable Bolt Diameter

Hexagonal

width across

flats H (mm)

Main Socket

Dimensions (mm)

Form B Form C

Form D

2. Long Socket

H S

ØF

H S

ØF

H S

ØF

H S

ØF

Table 1

English

3. Extension bar: Code No. 873633

The extension bar is convenient for working in very

restricted spaces or when the socket provided cannot

reach the bolt to be tightened.

CAUTION

When the extension bar is used, the tightening

torque is reduced slightly compared with the

ordinary socket.

4. Universal joint: Code No. 992610

The universal joint is convenient for impacting nuts

when there is an angle between the socket and

wrench, or when working in a very narrow space.

5. Duct Socket

This is used for tightening bolts and nuts on flange

sections of air conditioners, type ducts, etc.

6. Corner attachment (Model EW-14R)

Use this attachment only when the machine is

applied to the nut or bolt at the right angle.

7. Bit adaptor: Code No. 991476

This is used for tightening small screws (M6 – M8).

NOTE

(1) This adaptor is set only on the anvil (drive angle)

of the main unit. The bit adapter cannot be attached

to the special accessory anvil (square drive).

(2) Before starting work with the adapter, tighten a few

screws with it to make sure it’s tightening with the

appropriate torque.

(3) Tightening speed will be greatly reduced when

driving wood, tapping or other similar screws.

䢇 Applicable plus driver bit

Table 2

Code No.

High ISO ISO Inch

Form

tension

(ordinary)

(small) bolts L L1 L2 øF

12 mm 955138 M8 W5/16" 12 B 52 20 34 20

13 mm 955139 M8 13 B 52 20 34 21.5

14 mm 955140 M10 14 B 52 20 34 22

17 mm 955141 M10 M12 W3/8" 17 B 52 24 34 25

17 mm 955149 M10 M12 W3/8" 17 B 75 24 57 25

19 mm 955142 M12 M14 W7/16" 19 B 52 24 34 28

12.7

Long

19 mm 955150 M12 M14 W7/16" 19 B 75 24 57 28

Socket

21 mm 955143 W1/2" 21 D 52 24 34 31

21 mm 955151 W1/2" 21 D 75 24 57 31

21 mm 991480 W1/2" 21 D 125 24 107 31

22 mm 955144 M12 M14 M16 22 D 52 24 34 32.5

24 mm 955146 M16 M18 24 D 52 25 34 34

26 mm 955147 W5/8" 26 D 75 25 57 38

Square

head drive

dimensions

S (mm)

Part Name

Suitable Bolt Diameter

Hexagonal

width across

flats H (mm)

Main Socket

Dimensions (mm)

Code No.

Hexagonal width

across flats (mm)

993658 12

992613 13

992615 14

L 6.35

Bit No. L (mm) Code No.

No. 2

45 955229

70 955654

No. 3

45 955230

70 955655

Bit No.

English

Optional accessories are subject to change without

notice.

APPLICATION

䡬 Tightening and loosening of all types of bolts and

nuts, used for securing structural items.

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the hadle tightly and push the battery latch

to remove the battery (Fig. 1 and 2).

CAUTION

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities (See

Fig. 2).

CHARGING

Before using the impact wrench, charge the battery as

follows.

1. Connect the charger’s power cord to a receptacle

When the power cord is connected, the charger’s

pilot lamp will blink in red (At 1-second intervals).

2. Insert the battery into the charger

Insert the battery firmly, in the direction shown in

Fig. 3, until it contacts the bottom of the charger

compartment.

CAUTION

If the battery is inserted in the reverse direction,

not only recharging will become impossible, but it

may also cause the fuse to blow, or problems in

the charger such as deformed recharging terminal.

3. Charging

When inserting a battery in the charger, charging

will commence and the pilot lamp will light

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red (At 1-second intervals) (See

Table 3).

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown

in Table 3, according to the condition of the charger

or the rechargeable battery.

Table 3

Indications of the lamps

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Malfunction in the battery

or the charger.

The battery temperature

is high, making recharg-

ing impossible.

(2) Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in the table below, and batteries that have

become hot should be cooled for a while before

being recharged.

Table 4 Recharging ranges of batteries

(3) Regarding recharging time

Depending on the combination of the charger and

batteries, the charging time will become as shown

in Table 5.

Table 5 Charging time (At 20°C)

NOTE

The charging time may vary according to

temperature and power source voltage.

Temperatures at

Rechargeable batteries which the battery

can be recharged

EB14B –5°C – 60°C

EB1430H 0°C – 45°C

Charger

UC14YFA

Battery

EB14B Approx. 50 min.

EB1430H Approx. 70 min.

English

4. Disconnect the charger’s power cord from the

receptaele

5. Hold the charger firmly and pull out the battery

NOTE

After charging, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an

extended period is not activated, the electric

discharge might be low when using them the first

and second time. This is a temporary phenomenon,

and normal time required for recharging will be

restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the

electric current, the battery may be damaged and

its life will become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a

while.

CAUTION

䡬 If the battery has been heated right after operation

(or due to sunlight, etc.), the charger’s pilot lamp

may not light in red. In such a case, first let the

battery cool, then start charging.

䡬 When the pilot lamp flickers in red quickly (at 0.2-

second intervals), check for and take out any foreign

objects in the charger’s battery installation hole. If

there are no foreign objects, it is probable that the

battery or charger is malfunctioning. Take it to your

Authorized Service Center.

䡬 Since the built-in micro computer takes about 3

seconds to confirm that the battery being charged

with UC14YFA is taken out, wait for a minimum of

3 seconds before reinserting it to continue charging.

If the battery is reinserted within 3 seconds, the

battery may not be properly charged.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

2. Checking the battery

Make sure that the battery is installed firmly. If it

is at all loose it could come off and cause an

accident.

3. Selecting the socket matched to the bolt

Be sure to use a socket which is matched to the

bolt to be tightened. Using an improper socket will

not only result in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex. or square-holed socket

will not give an adequate tightness for fitting to the

nut or anvil, consequently resulting in loss of

tightening torque.

Pay attention to wear of socket hole, and replace

before further wear has developed.

Finally, install the socket prescribed in Item 4. The

section on “Optional Accessories” details the

relationship between bolt sizes and sockets. Sockets

are named according to the dihedral width of the

hexagonal hole.

4. Installing a socket

Select the socket to be used.

䢇 Pin, O-ring type (Fig. 4 and 5)

(1) Align the hole in the socket with the hole in the

anvil and insert the anvil into the socket.

(2) Insert the pin into the socket.

(3) Attach the ring to the groove on the socket.

䢇 Plunger type (Fig. 6)

Align the plunger located in the square part of the

anvil with the hole in the hex. socket. Then push

the plunger, and mount the hex. socket on the anvil.

Check that the plunger is fully engaged in the hole.

When removing the socket, reverse the sequence.

HOW TO USE

1. Using the convenient hook

The convenient hook can be installed on the right

or left side and the angle can be adjusted in 5 steps

between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction

of arrow (A) and turn in the direction of arrow

(B) (Fig. 7).

(b) The angle can be adjusted in 5 steps (0°, 20°,

40°, 60°, 80°).

Adjust the angle of the hook to the desired

position for use.

(2) Switching the hook position

CAUTION

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the

screw using a slotted head screwdriver or a coin

(Fig. 8).

(b) Remove the hook and spring (Fig. 9).

securely fasten with screw (Fig. 10).

NOTE

Pay attention to the spring orientation. Install the

spring with larger diameter away from you (Fig. 10).

(3) Using as an auxiliary light

(a) Press the switch to turn off the light.

If forgotten, the light will turn off automatically

after 15 minutes.

(b) The direction of the light can be adjusted within

the range of hook positions 1 - 5 (Fig. 11).

䡬 Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION

Do not look directly into the light.

Such actions could result in eye injury.

English

(4) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

screwdriver (No. 1) (Fig. 12).

Remove the hook cover by pushing in the

direction of the arrow (Fig. 13).

(b) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly (Fig. 14).

with the protuberance of the hook cover, press

the hook cover in the direction opposite to that

of the arrow shown in Fig. 13 and then tighten

the screw.

Use commercially available AAAA batteries

(1.5 V).

NOTE

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION

䡬 Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals

correctly.

Replace both batteries at the same time. Do not mix

old and new batteries.

Remove exhausted batteries from the hook

immediately.

䡬 Do not discard batteries together with normal trash

and do not throw batteries into fire.

䡬 Store batteries out of the reach of children.

䡬 Use batteries correctly in accordance with the battery

specifications and indications.

2. Check the rotational direction

The bit rotates clockwise (viewed from the rear

side) by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the

bit counterclockwise (See Fig. 15) (The

and

marks are engraved on the body).

CAUTION

The push button can not be switched while the

impact driver is turning. To switch the push button,

stop the impact driver, then set the push button.

3. Switch operation

䡬 When the trigger switch is depressed, the tool

rotates. When the trigger is released, the tool stops.

䡬 The rotational speed can be controlled by varying

the amount that the trigger switch is pulled. Speed

is low when the trigger switch is pulled slightly and

increases as the trigger switch is pulled more.

4. Tightening and loosening bolts

A hex socket matching the bolt or nut must first

be selected. Then mount the socket on the anvil,

and grip the nut to be tightened with the hex socket.

Holding the wrench in line with the bolt, press the

power switch to impact the nut for several seconds.

If the nut is only loosely fitted to the bolt, the bolt

may turn wit the nut, therefore mistaking proper

tightening. In this case, stop impact on the nut and

hold the bolt head with a wrench before restarting

impact, or manually tighten the bolt and nut to

prevent them slipping.

5. Number of bolt tightened possible

Please refer to the table below for the number of

bolt tightened possible with one charge.

EB1430H

These values may vary slightly, according to

surrounding temperature and battery characteristics.

NOTE

The use of the battery EB1430H in a cold condition

(below 0°C) can sometimes result in the weakened

tightening torque and reduced amount of work.

This, however, is a temporary phenomenon, and

returns to normal when the battery warms up.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest

the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

NOTE

Do not touch the hammer case, as it gets very hot

during continuous work.

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which

steplessly varies the rotation speed. Consequently,

when the switch trigger is pulled only slightly (low

speed rotation) and the motor is stopped while

continuously driving in screws, the components of

the electronic circuit parts may overheat and be

damaged.

3. Tightening torque

Refer to Fig. 20 for the tightening torque of bolts

(according to size), under the conditions shown in

Fig. 21. Please use this example as a general

reference, as tightening torque will vary according

to tightening conditions.

Tightening torque varies, depending on the battery’s

charge level. Fig. 22 shows an example of the

relationship between tightening torque and the

number of tightenings, for WR14DM. As shown,

tightening torque gradually weakens with the

increase in the number of tightenings. In particular,

as the torque decreases very close to the complete

discharge (“a” margin in graph), the unit’s impact

weakens, the number of time impacts declines and

tightening torque drops off abruptly. If this occurs,

check torque level, then recharge the battery if

necessary.

4. Work at a tightening torque suitable for the bolt

under impact

The optimum tightening torque for nuts or bolts

differs with material and size of the nuts or bolts.

An excessively large tightening torque for a small

bolt may stretch or break the bolt. The tightening

torque increases in proportionate to the operaton

time. Use the correct operating time for the bolt.

5. Holding the tool

Hold the impact wrench firmly with both hands. In

this case hold the wrench in line with the bolt.

It is not necessary to push the wrench very hard.

Hold the wrench with a force just sufficient to

counteract the impact force.

Bolt used No. of tightenings

M16 × 55 (F10T) Approx. 126

English

6. Confirm the tightening torque

The following factors contribute to a reduction of

the tightening torque. So confirm the actual

tightening torque needed by screwing up some

bolts before the job with a hand torque wrench.

Factors affecting the tightening torque are as follows.

(1) Voltage

When the discharge margin is reached, voltage

decreases and tightening torque is lowered.

(2) Operating time

The tightening torque increases when the operating

time increases. But the tightening torque does not

increase above a certain value even if the tool is

driven for a long time (See Fig. 20).

(3) Diameter of bolt

The tightening torque differs with the diameter of

the bolt as shown in Fig. 20. Generally a larger

diameter bolt requires larger tightening torque.

(4) Tightening conditions

The tightening torque differs according to the torque

ratio; class, and length of bolts even when bolts

with the same size threads are used. The tightening

torque also differs according to the condition of the

surface of workpiece through which the bolts are

to be tightened. When the bolt and nut turn together,

torque is greatly reduced.

(5) Using optional parts

The tightening torque is reduced a little when an

extension bar, universal joint or a long socketis

used.

(6) Clearance of the socket

A worn or deformed hex or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque.

Using an improper socket which does not match

to the bolt will result in an insufficient tightening

torque. Matching socket and bolt sizes are shown

in Table 1 and 2.

Tightening time: sec

(Steel plate thickness

t = 10 mm)

Tightening time: sec

(Steel plate thickness

t = 25 mm)

Tightening time: sec

(Steel plate thickness

t = 25 mm)

Tightening torque

Fig. 20

Explanation of strength grade:

4 — Yield point of bolt: 320 N/mm

{32.6 kgf/mm

}

8 — Pulling strength of bolt: 400 N/mm

{40.8 kgf/mm

}

* The following bolt is used.

Ordinary bolt: Strength grade 4.8

High tensile bolt: Strength grade 12.9

(

Bolt

Nut

Fig. 21

Steel plate thickness t

)

M10 × 30

kgf

•

2000

1500

1000

500

•

200

150

100

M12 × 45

kgf

•

2000

1500

1000

500

•

200

150

100

M14 × 50

kgf

•

2000

1500

1000

500

•

200

150

100

High tension bolt

Ordinary bolt

High tension bolt

Ordinary bolt

High tension bolt

English

300

250

200

150

100

20 40 60 80 100 120 140

3000

2500

2000

1500

1000

500

kgf

•

cm N

•

Tightening torque

Number of tightenings (PCS)/charging

When full recharged

When completely discharged

Fig. 22

M16 × 55 F10T (tighening time 3 sec)

MAINTENANCE AND INSPECTION

1. Inspecting the socket

A worn or deformed hex or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque. Pay attention to wear of

a socket holes periodically, and replace with a new

one if needed.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so may result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very "heart" of the

power tool.

Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 16)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn

carbon brush can result in motor trouble, replace

the carbon brush with new ones when it becomes

worn to or near the "wear limit". In addition, always

keep carbon brushes clean and ensure that they

slide freely whthin the brush holders.

NOTE

When replacing the carbon brush with a new one,

be sure to use the Hitachi Carbon Brush Code No.

999054.

5. Replacing carbon brushes

Take out the carbon brush by first removing the

brush cap and then hooking the protrusion of the

carbon brush with a flat head screw driver, etc., as

shown in Fig. 18.

When installing the carbon brush, choose the

direction so that the nail of the carbon brush agrees

with the contact portion outside the brush tube.

Then push it in with a finger as illustrated in

Fig. 19. Lastly, install the brush cap.

CAUTION

Be absolutely sure to insert the nail of the carbon

brush into the contact portion outside the brush

tube. (You can insert whichever one of the two

nails provided.)

Caution must be exercised since any error in this

operation can result in the deformed nail of the

carbon brush and may cause motor trouble at an

early stage.

6. Cleaning of the outside

When the impact wrench is stained, wipe with a

soft dry cloth or a cloth moistened with soapy

water. Do not use chloric solvents, gasoline or paint

thinner, as they melt plastics.

7. Storage

Store the impact wrench in a place in which the

temperature is less than 40°C, and out of reach of

children.

8. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION

Repair, modification and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools,

the safety regulations and standards prescribed in

each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

NOTE:

Due to HITACHI’s continuing program of reserch and

development, the specifications herein are subject to

change without prior notice.

English

IMPORTANT

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: –Neutral

Brown: –Live

As the colours of the wires in the mains lead of this

tool may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the

terminal marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN50144.

The typical A-weighted sound pressure level: 99 dB (A)

The typical A-weighted sound power level: 112 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration

value: 23 m/s

Deutsch

VORSICHT FÜR ALLGEMEINE BEDIENUNG

1. Den Arbeitsplatz stets sauber halten. Unaufger-

äumte Arbeitsplätze und Werkbänke erhöhen die

Unfallgefahr.

2. Gefährliche Umgebungen vermeiden. Die Maschine

und das Ladegerät keiner Feuchtigkeit aussetzen

oder an nassen Stellen benutzen. Achten Sie auf

einen hellen, wenn erforderlich gut beleuchteten

Arbeitsplatz. Maschine und Ladegerät niemals in

der Nähe von brennbaren oder explosiven

Materialien, Flüssigkeiten oder Gasen verwenden.

3. Das Gerät ist nicht für Verwendung durch Kinder

oder gebrechliche Personen ohne Aufsicht gedacht.

Kinder sollten beaufsichtigt werden, um

sicherzustellen, dass sie nicht mit dem Gerät

spielen. Alle Besucher sollten in sicherer

Entfernung vom Arbeitsbereich gehalten werden.

4. Unbenutztes Werkzeug und Ladegerät an einen

trockenen und verschlossenen Ort wegräumen;

außerhalb der Reichweite von Kindern und

gebrechlichen Personen aufbewahren. Die

Temperatur sollte weniger als 40°C betragen.

5. Das Werkzeug nicht überlasten. Es arbeitet sich

besser und sicherer bei angemessenen Gesch-

windigkeiten und Belastungen.

6. Das richtige Werkzeug zur Arbeit verwenden.

Erwarten Sie nicht, daß ein zu kleines Werkzeug

oder Zubehör die Arbeit einer Hochleistung-

smaschine verrichtet.

7. Achten Sie auf die richtige Kleidung. Lose oder

zu weite Kleidung bzw. und/oder Schmuck (z.B.

Ketten, Ringe, usw.) könnten sich in rotierenden

oder bewegenden Teilen verfangen. Schutzhand-

schuhe und Arbeitsschutzschuhe sind bei

denArbeiten zu tragen.

8. Vergessen Sie nicht bei Arbeiten mit Werkzeugen

eine Sicherheitsbrille zu tragen, ebenfalls, wenn

erforderlich eine Gesichts-oder Staubmaske.

9. Schonen Sie das Anschlußkabel. Tragen Sie

niemals das Ladegerät am Kabel und ziehen Sie

nicht daran, um den Stecker von der Steckdose

zu trennen. Das Kabel gegen übermäßige Hitze,

Öl und scharfe Kanten schützen.

10. Das zu bearbeitende Werkstück gut sichern.

Zwingen oder Schraubstock für die Befestigung

des Werkstücks benutzen. Es erhöht die Sicherheit

und schafft freie Hände zur Bedienung des

Werkzeugs.

11. Verschaffen Sie sich einen festen Stand, er

garantiert Sicherheit und optimales Gleichgewicht

bei der Arbeit.

12. Das Werkzeug in gutem Zustand behalten. Stets

sauber halten, pflegen und warten, damit es immer

die beste Leistung bringt. Beachten Sie die

Anweisungen für Schmieren oder eventuelle

Auswechselungen.

13. Wird das Ladegerät nicht benutzt oder einer

Prüfung unterzogen, entfernen Sie den Stecker

aus Ihrem Wechselstro-manschluß.

14. Spannschlüssel und/oder Bohrfutterschlüssel vor

dem Gebrauch des Werkzeugs aus der Maschine

entfernen.

15. Zufälliges Einschalten vermeiden. Das Werkzeug

nicht mit dem Finger am Schalter tragen.

16. Um Gefahren zu vermeiden, verwenden Sie nur

das vorgeschriebene Ladegerät.

17. Nur Original-HITACHI-Ersatzteile verwenden.

18. Das Werkzeug und Ladegerät nicht anders als in

der Gebrauchsanweisung vorgeschrieben

verwenden.

19. Die Benutzung von Zubehör und Sonderzubehör,

die nicht im HITACHI-Katalog oder in der

Bedienungsanleitung aufgeführt sind, erhöhen das

Risiko von Verletzungen.

20. Reparaturen sollten nur in autorisierten HITACHI-

Service-Werkstätten durchgeführt werden.

Der Hersteller haftet nicht für Schäden und Unfälle,

die auf unautorisierte Fachkräfte oder auf den

Mißbrauch des Werkzeugs zurückgeführt werden

können.

21. Um den ursprünglichen Zustand des Werkzeugs

und Ladegerätes zu erhalten, entfernen Sie keine

Hinweisschilder, Abdeckungen oder Schrauben.

22. Nehmen Sie das Ladegerät immer nur mit der auf

dem Typenschild vorgeschriebenen Spannung in

Gebrauch.

23. Bewegliche Teile und Zubehöre nicht berühren,

wenn das Werkzeug nicht vom Netz abgetrennt

ist.

24. Immer vor der Benutzung die Batterie aufladen.

25. Nur die vorgeschriebene Batterie verwenden. Keine

gewöhnlichen Trockenbatterien oder Auto-

Batterien, für das Elektro-Werkzeug verwenden.

26. Keinen Transformator mit Puffersatz verwenden.

27. Die Batterie nicht an einem elektrischen Generator

oder einer Gleichstromversorgung aufladen.

28. Die Batterie immer drinnen aufladen. Da sich beim

Laden Ladegerät und Batterie erwärmen, an einem

Ort aufladen, der nicht direkter Sonnenbestrahlung

ausgesetzt und trocken ist.

29. Wenn an hochliegenden Stellen gearbeitet

wird,(z.B. Gerüst, Treppe) vergewissern Sie sich

vor Arbeitsbeginn, daß sich under Ihnen keiner im

Arbeits-bzw. Gefahrenkreis aufhält.

30. Die detaillierte Bestandsteilzeichnung, die der

Bedienungsanleitung beigefügt ist, ist nur für die

autorisierte Service-Werkstätte bestimmt.

31. Falls das mitgelieferte Kabel beschädigt wird, muss

es durch den Hersteller, seinen

Kundendienstvertreter oder eine ähnlich

qualifizierte Person ausgewechselt werden, um

Gefahren zu vermeiden.

VORSICHTSMASSNAHMEN FÜR DEN

AKKU-SCHLAGSCHRAUBER

1. Dies ist ein tragbares Werkzeuggerät zum Anziehen

und Lösen von Schrauben. Es sollte nur für diesen

Zweck eingesetzt werden.

2. Bei längerem Arbeiten Ohrstöpsel verwenden.

3. Es ist äußerst gefährlich, das Gerät nur mit einer

Hand zu bedienen. Das Gerät ist beim Betrieb mit

beiden Händen festzuhalten.

4. Nachprüfen, ob die Buchse gesprungen oder

gebrochen ist. Gebrochene und gesprungene

Buchsen sind gefährlich, daher die Buchse vor

Gebrauch prüfen.

5. Die Buchse mit Buchsenstift und-ring sichern. Sollte

der Buchsenstift oder-ring beschädigt sein, kann

die Buchse vom Schlag-Schrauber geschleudert

werden, was gefährlich ist. Niemals Buchsenstifte

oder-ring verwenden, die deformiert, abgenutzt,

gesprungen oder sonstwie beschädigt sind. Immer

darauf achten, daß Buchsenstift und -ring in der

richtigen Position sind.

6. Das Anzugsdrehmoment prüfen.

Das geeignete Drehmoment für das Anziehen einer

Schraube hängt vom Material, der Art, den

Abmessungen, usw. der Schraube ab.

Außerdem hängt das von diesem Schlag-Schrauber

erzeugte Auzugsdrehmoment vom Material und

den Abmessungen der Schraube, für welche

zeitdauer der Schlag-Schrauber angewendet wird,

wie die Bushse angebracht ist, usw. ab. Das

Drehmomentvariiert auch leicht, wenn die Batterie

gerade aufgeladen wurde und wenn sie kurz vor

dem Erschöpfen steht. Mit einem

Anzugsdrehmomentschlüssel nachprüfen, ob die

Deutsch

11. Das Ladegerät nicht fortlaufend laden.

Nach Beendung einer Ladung, lassen Sie das

Ladegerät ungefähr 15 Minuten ruhen bevor die

nächste Batterieladung unternommen wird.

12. Keine Fremdkörper durch das Anschlußloch der

Batterie eindringen lassen.

13. Niemals die Batterie und das Ladegerät

auseinandernehmen.

14. Niemals die Batterie kurzschließen.

Kurzschluß der Batterie verursacht eine zu große

Stromzufuhr und Überhitzung, wodurch

Durchbrennen oder Schaden beider Batterie

ensteht.

15. Die Batterie nicht ins Feuer werfen.

Sie könnte dabei explodieren.

16. Darauf achten, daß keine Gegenstände durch

Belüftungsschlitze des Aufladers in das Gerät

eindringen.

Wenn Metallobjekte oder entzündliche

Gegenstände durch die Belüftungsschlitze des

Aufladers eindringen, kann dies zu elektrischen

Schlägen führen oder den Auflader beschädigen.

17. Bringen Sie die Batterie zum Geschäft, wo Sie ihn

gekauft haben sobald die Lebensdauer der Batterie

abrinnent. Die erschöpfte Batterie nicht wegwerfen.

18. Benutzung verbrauchter Batterie beschädigt den

Auflader.

MODELL

WR14DM: mit Ladegerät und Gehäuse

Schraube mit dem richtigen Drehmoment

angezogen wurde.

7. Den Schlag-Schrauber zuerst stoppen, wenn die

Rotationsrichtung geändert werden soll. Den

Schalter immer erst freigeben und warten, bis der

Schlag-Schrauber stoppt, bevor auf die

entgegengesetzte Rotationsrichtung geschaltet

wird.

8. Niemals die rotierenden Teile berühren.

Darauf achten, daß sich der rotierende Buchsenteil

immer in genügendem Abstand zum Körper und

den Händen befindet, da die Gefahr besteht, sich

zu schneiden oder sich in der Buchse zu verfangen.

Die Buchse sollte auch nicht direkt nach langer

kontinuierlicher Benutzuntg berührt werden, da

durch die erzeugte Hitze Verbrennungsgefhr

besteht.

9. Den Schlag-Schrauber bei Benutzung des

Universalgelenks niemals ohne Einspannung

rotieren lassen.

Wenn sich die Buchse ohne eingespannt zu sein

dreht verusacht das Universalgelenk ein wildes

Rotieren der Buchse.

Durch die schnelle Rotation der Buchse kann der

Schlag-Schrauber so stark vibrieren, daß er

losgelassen werden muß. Es besteht hohe

Verletzungsgefahr.

10. Die Batterie immer bei einer Temperatur von 0

- 40°C laden.

Laden bei einer Temperatur die niedriger als 0°C

is twird gefährliche Überladung verursachen. Die

Batterie kann nicht bei einer Temperatur über

40°C geladen werden. Die beste Temperatur zum

Laden wäre von 20 - 25°C.

TECHNISCHE DATEN

ELEKTRO-WERKZEUG

Modell WR14DM

Leerlaufdrehzahl 0 – 2300 min

–1

Winkelgetriebe 12,7 mm

Kapazität M10 – M16 (Üblicher Bolzen)

M8 – M14 (Hochzugfester Bolzen)

Spanndrehkraft

Wiederaufladbare EB14B Ni-Cd Batterie, 14,4 V

(2,0 Ah, 12 Zellen)

EB1430H Ni-MH Batterie, 14,4 V

(3,0 Ah, 12 Zellen)

Gewicht 1,9 kg

Maximum

200 N·m {2040 kgf·cm}

Festspannen von M16 (F10T) reißfeste Schraube bei voller Aufladung und einer

Temperatur von 20°C.

Festspannungsdauer: 3 sec.

LADEGERÄT

Modell UC14YFA

Ladedauer EB14B: Etwa. 50 min. (bei 20°C)

EB1430H: Etwa. 70 min. (bei 20°C)

Ladespannung 7,2 – 14,4 V

Gewicht 0,6 kg

Deutsch

SONDERZUBEHÖR

(separat zu beziehen)

1. Buchsen

Form B Form C

Form D

Tafel 1

Code Nr. Hohe Zu-

ISO ISO

Bolzen mit

Form

gfestigkeit

(üblich) (klein)

Zollmaß

LL1øF

10 mm 944291 M6 10 B 40 8 18

12 mm 873632 M8 W5/16" 12 B 40 8 20

13 mm 873539 M8 13 B 40 9 25

14 mm 873540 M10 14 B 40 9 25

17 mm 873536 M10 M12 W3/8" 17 C 32 8 28

12,7

Sechskant-

19 mm 873624 M12 M14 W7/16" 19 C 34 9 28

buchse

21 mm 873626 W1/2" 21 D 36 10 32

22 mm 873627 M12 M14 M16 22 D 40 14 35

24 mm 873629 M16 M18 24 D 40 15 38

26 mm 873630 W5/8" 26 D 40 15 38

27 mm 985195 M16 M18 M20 27 D 40 16 42

Vierkantiko-

pf-Antrib

Maß S

(mm)

Passender Bolzen und Durchmesser

Zylinderbolzer

mit Innen-

sechskant

H (mm)

Ausmaße der

Hauptbuchse (mm)

Form B Form C

Form D

2. Lange Buchse

Name des

Fabrikats

H S

ØF

H S

ØF

H S

ØF

H S

ØF

STANDARDZUBEHÖR

1. Ladegerät (UC14YA) .............................................. 1

2. Plastikgehäuse ........................................................ 1

Das Standardzubehör kann ohne vorherige

Bekanntmachung jederzeit geändert werden.

Deutsch

Tafel 2

Code Nr. Hohe Zu-

ISO ISO

Bolzen mit

Form

gfestigkeit

(üblich) (klein)

Zollmaß

LL1L2øF

12 mm 955138 M8 W5/16" 12 B 52 20 34 20

13 mm 955139 M8 13 B 52 20 34 21,5

14 mm 955140 M10 14 B 52 20 34 22

17 mm 955141 M10 M12 W3/8" 17 B 52 24 34 25

17 mm 955149 M10 M12 W3/8" 17 B 75 24 57 25

Lange-

19 mm 955142 M12 M14 W7/16" 19 B 52 24 34 28

12,7

buchse

19 mm 955150 M12 M14 W7/16" 19 B 75 24 57 28

21 mm 955143 W1/2" 21 D 52 24 34 31

21 mm 955151 W1/2" 21 D 75 24 57 31

21 mm 991480 W1/2" 21 D 125 24 107 31

22 mm 955144 M12 M14 M16 22 D 52 24 34 32,5

24 mm 955146 M16 M18 24 D 52 25 34 34

26 mm 955147 W5/8" 26 D 75 25 57 38

Vierkantiko-

pf-Antrib

Maß S

(mm)

Passender Bolzen und Durchmesser

Zylinderbolzer

mit Innen-

sechskant

H (mm)

Ausmaße der

Hauptbuchse (mm)

Name des

Fabrikats

3. Verlängerungsstange: Code-Nr. 873633

Die Verlängerungsstange ist praktisch zum Arbeiten

an beengten Plätzen oder wenn die mitgelieferte

Muffe die anzuziehende Schraube nicht erreichen

kann.

VORSICHT

Wenn die Verlängerungsstange benutzt wird, ist das

Anzugsdrehmoment im Vergleich zu der normalen

Muffe leicht reduziert.

4. Universalverbindung: Code-Nr. 992610

Die Universalverbindung ist praktisch zum Anziehen

von Muttern, wenn sich zwischen der Muffe und

dem Schrauber ein Winkel befindet oder wenn auf

sehr engem Raum gearbeitet wird.

5. Durchführungsbuchse

Diese wird Festziehen von Bolzen und Muttern an

Flansch-Abschnitten verwende, wie sie in

Durchführungen von Kühlanlagen usw. zu finden

sind.

6. Eckenkupplung (Modell EW-14R)

Diese Eckenkupplung wird gebraucht, wenn das

Gerät zum Drehen von Muttern oder Bolzen

rechtwinklig anwendet wird.

7. Muffenadapter: Code-Nr. 991476

Dieser wird verwendet, um kleine Schrauben

festzuziehen (M6 – M8).

ANMERKUNG

(1) Dieser Adapter für den Werkzeugeinsatz wird nur

für den Antriebswinkel der Haupteinheit eingestellt.

Der Muffenadapter kann nicht an dem

Sonderzubehöramboss (quadratischer Antrieb)

angebracht werden.

(2) Zur Vergewiserung des Anzugsmoments sind vor

der Inbetriebnahme mit dem Adapter einige

Schrauben probeweise damit festzuziehen.

(3) Bei Festziehen von Holz, Schneid -oder ähnlichen

Schrauben kommt es zu einer erheblichen

Verringerung der Anzugsgeschwindigkeit.

Code-Nr.

Zylinderbolzen mit

Innensechskant (mm)

993658 12

992613 13

992615 14

La pagina sta caricando ...

Hitachi WR 14DM Handling Instructions Manual

Marca: Hitachi

Modello: WR 14DM

Tipo: Handling Instructions Manual

Scarica il pdf

rapporto

in altre lingue

English: Hitachi WR 14DM
français: Hitachi WR 14DM
español: Hitachi WR 14DM
Deutsch: Hitachi WR 14DM
Nederlands: Hitachi WR 14DM
português: Hitachi WR 14DM

Documenti correlati

Altri documenti

Facom 914 Manuale del proprietario