AJA 12GM Manuale utente

Marca: AJA

Modello: 12GM

Categoria: Convertitori video

Tipo: Manuale utente

12GM Mini-Converter

12G-SDI to/from SDI Muxer/DeMuxer

Version 1.6r1

Published December 2, 2019

Installation and Operation Guide

12GM Mini-Converter v1.6r1 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

CION®, Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered

trademarks of AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, TruZoom™,

V2Analog™ and V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web

https://www.aja.com

Support Email

suppor[email protected]

Sales Email

[email protected]

12GM Mini-Converter v1.6r1 3 www.aja.com

Table of Contents

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

I/O Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

USB Control and Setup—Using AJA Mini-Cong . . . . . . . . . . . . . . . . . . . 7

Acquiring AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Mini-Converter Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PC Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mac Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Running AJA Mini-Cong. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PC Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Mac Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Saving Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operating AJA Mini-Cong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Input Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Input Detail Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Timing Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Output Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Output Detail Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Update Tab Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Software Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 23

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . .25

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . .33

Limited Warranty on Hardware.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Governing Law and Language; Your Rights. . . . . . . . . . . . . . . . . . . . . 33

12GM Mini-Converter v1.6r1 4 www.aja.com

Chapter 1 – Introduction

Overview

12GM is a compact SDI transport converter that can solve a wide range of

UltraHD/4K equipment inter-connection problems. The product will convert

quad-link SDI signals to single-link SDI (Mux function) as well as single-link SDI to

quad-link SDI (Demux function).

12GM supports Two Sample Interleave (2SI) to Square Division (Quadrant) and

Square Division (Quadrant) to Two Sample Interleave (2SI) pixel mapping. 12GM

also supports 3G-SDI Level A and Level B-DL.

The 12GM is configured using the free AJA Mini-Config application, which also

provides detailed input and output signal diagnostic information.

Features

• Quad 3G-SDI Level A to Single 12G-SDI

• Quad 3G-SDI Level B-DL to Single 12G-SDI

• Single 12G-SDI to Quad 3G-SDI Level A

• Single 12G-SDI to Quad 3G-SDI Level B-DL

• Quad 1.5G-SDI to Single 6G-SDI

• Single 6G-SDI to Quad 1.5G-SDI

• Quad 3G-SDI Level A to Quad 3G-SDI Level B-DL

• Quad 3G-SDI Level B-DL to Quad 3G-SDI Level A

• Two Sample Interleave (2SI) to Square Division (Quadrant) pixel mapping

• Square Division (Quadrant) to Two Sample Interleave (2SI) pixel mapping

• Pass through of Single Link 3G, 1.5G and 270M SDI video

• Distribution Amplier support (1x4)

• Input signal diagnostics

12GM Mini-Converter v1.6r1 5 www.aja.com

• Input timing analyzer for quad link signals

• Automatic or manual control

• Detailed timing analysis for validating alignment of quad-link SDI inputs

• Passes SDI embedded audio, 24-bit, up to 16-Channels

• Recognizes and transmits High Dynamic Range (HDR) and Wide Color Gamut

(WCG) signaling on VPID

• DWP-U-R1 power supply included

• Five year warranty

Block Diagram

Figure 1. 12GM Converter, Simplified Block Diagram

SDI Input 1

SDI Receiver

SDI Input 2

SDI Input 3

SDI Input 4

SDI Receiver

SDI

Processing

SDI Transmitter

SDI Output 1

SDI Output 2

SDI Output 3

SDI Output 4

SDI Transmitter

I/O Connections

Figure 2. 12GM Converter Connections

USB Port

+5-20 VDC

Power

Input

SDI Output 1

SDI Output 3

SDI Output 4

SDI Output 2

SDI Input 1

SDI Input 3

SDI Input 4

SDI Input 2

NOTE: The LEDs adjacent to each SDI input connector indicate by color the detected

signal type. Off is no signal, Green is SD-SDI, Red is HD-SDI, Amber is 3G-SDI,

Purple is 6G-SDI, and Blue is 12G-SDI.

12GM Mini-Converter v1.6r1 6 www.aja.com

Installation

Typically, 12GM installation consists of the following steps:

1. Ensure the 12GM is disconnected from power.

2. Connect video equipment to the converter BNC connectors.

3. Apply power to the converter (AJA power supply included).

4. The 12GM will now run using the default factory settings. If you wish to alter

the factory settings, you’ll need to:

• Install the AJA Mini-Cong software on your computer

• Attach the 12GM via USB

• Make your changes using AJA Mini-Cong setup screens.

This process is detailed in "USB Control and Setup—Using AJA Mini-Config" on page

NOTE: The 12GM packs an unprecedented feature set into a mini converter box. As a

result, the unit uses approximately 12 watts of power. It will be very warm to

the touch, which is normal. The unit is engineered to operate across the full

temperature range, from 0 to 40 degrees C.

NOTE: For highest reliability, the mini converter relies on convection cooling instead

of using a built-in fan. Therefore, when installing the unit, mount in a location

where it has access to air for proper cooling. Do not stack the 12GM with other

mini converters.

12GM Mini-Converter v1.6r1 7 www.aja.com

Chapter 2 – Operation

USB Control and Setup—Using AJA Mini-Config

Your AJA Mini-Converter can be used right out of the box for some applications

since it is designed to recognize inputs and perform standard actions

automatically by default. However, to use its full capability, you must use AJA’s

Mini-Config software application for PCs and Macs. This same application can be

used to update to new Mini-Converter software released by AJA.

Acquiring AJA Mini-Config

AJA’s Mini-Config application is available for download from the AJA website.

To download the latest AJA Mini-Config package, which includes the AJA Mini-

Config application, Mini-Converter firmware, and documentation, go to:

https://www.aja.com/en/products/mini-converters/mini-cong-software

Select either the Windows or Mac icon to download the desired version.

CAUTION: If you are running Mini-Config on macOS Catalina, please make sure you

are using Mini-Config v2.24.1 or later. Earlier versions of Mini-Config are not

compatible with macOS Catalina.

Mini-Converter Documentation

Included with the AJA Mini-Config package is a complete set of documentation

for all Mini-Converters supported by AJA Mini-Config. A .PDF of the Installation

and Operation Guide for the currently connected Mini-Converter can be accessed

from the AJA Mini-Config UI via the Help/Manual drop-down menu.

Documentation for all AJA Mini-Converters that use AJA Mini-Config can also

be accessed directly in the AJA Mini-Config download package Documentation

folder, and via the Documentation icon available on the Mac installer.

Documentation (and firmware) included with the AJA Mini-Config application

are the versions available at the time of distribution. However, Mini-Converter

software, firmware and documentation are updated regularly, so newer versions

may exist.

To download the latest documentation for an individual Mini-Converter, go to:

https://www.aja.com/en/category/mini-converters

and navigate to the Support webpage of that Mini-Converter.

Installing AJA Mini-Config

PC Installation

To install AJA Mini-Config on a Windows PC:

1. Download the application from the AJA website (select the Windows icon

on the AJA Mini-Cong Support webpage).

2. Open the AJA_MiniCong.zip le

3. Double-click on the MiniInstaller.msi le.

12GM Mini-Converter v1.6r1 8 www.aja.com

4. A Setup Wizard will guide you through the installation.

Figure 3. AJA Mini-Config PC Setup Wizard

5. Click Next to begin. Answer the questions in the subsequent dialogues.

When nished, an AJA Mini-Cong shortcut will be installed on the desktop,

and you will be able to locate the AJA Mini-Cong application in the AJA

folder in the Programs listing.

NOTE: If the AJA Mini-Config application already exists on the PC, a different Setup

Wizard appears.

Figure 4. AJA Mini-Config Setup Wizard, Reinstallation

With this screen you can Repair (reinstall) or Remove (uninstall) AJA Mini-Config

on the PC.

Mac Installation

To install the application on a Mac:

NOTE: Macintosh computers must be Intel-based (G5, G4 and earlier models will not

work with AJA Mini-Config).

1. Download the application from the AJA website (select the Apple icon on

the AJA Mini-Cong Support webpage).

2. Open the AJA_MiniCong folder.

12GM Mini-Converter v1.6r1 9 www.aja.com

3. Double-click on the AJAMiniCong.dmg le.

4. Answer the prompt and a utility program will be launched.

Figure 5. AJA Mini-Config Mac Installer

5. To complete the installation drag the “MiniCong.app” icon to the

Applications folder.

Running AJA Mini-Config

Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect

the external power supply (supplied) to the Mini-Converter.

PC Startup

To run AJA Mini-Config on a PC, double-click on the AJA Mini-Config icon on your

desktop, or open the AJA folder in the program list and click on the AJA Mini-

Config application located inside the AJA Mini-Config folder.

Mac Startup

To run AJA Mini-Config on a Mac, open the Applications folder and locate the AJA

Mini-Config application. Double-click the application to launch it.

12GM Mini-Converter v1.6r1 10 www.aja.com

Saving Setups

A File drop down menu on the AJA Mini-Config application bar allows you to

save the current state of the Mini-Converter to a preset file for later recall.

Using this feature you can set up the converter for different applications, storing

each configuration (Save Preset As...) with a unique name for easy recall (Open

Preset...).

A Revert to Factory Settings menu item similarly allows you to change the

settings back to AJA’s factory defaults.

Operating AJA Mini-Config

The AJA Mini-Config application provides a graphic interface for viewing settings

and updating software. It consists of an information area at the top that shows

the available Mini-Converters attached to the computer via USB, with a graphical

rendering of the selected Mini-Converter showing all the connectors and their

current state.

Colored text next to the connectors indicates the signal type and what the Mini-

Converter is doing:

• Blue text indicates the values automatically selected

• Black text indicates values that you have manually selected

• Red text indicates the Mini-Converter is not detecting a signal, or cannot

operate with the current user settings.

NOTE: Even if no output device is detected, the SDI connector text still shows the signal it

is outputting.

NOTE: Configuration settings in red will change based on the attached output device as

well as input signals. For improved accuracy and reliability, you should configure

the Mini-Converter only when the target output device is attached and input

signals are supplied at the inputs.

Screens are virtually the same on both PC and Mac, with subtle differences that

reflect the general look of the platform environment.

12GM Mini-Converter v1.6r1 11 www.aja.com

Figure 6. Example AJA Mini-Config Screen

Select a USB port and

an attached

Mini-Converter (name

in parentheses).

The status represents

the aggregate signal

currently detected

by one or four

connectors.

Firmware Version

and Serial Number

Status Message

Tabbed Screens

NOTE: The LEDs adjacent to each SDI input connector indicate by color the detected

signal type. Off is no signal, Green is SD-SDI, Red is HD-SDI, Amber is 3G-SDI,

Purple is 6G-SDI, and Blue is 12G-SDI.

Selecting a Mini-Converter with the pulldown menu causes this application to

connect to the selected converter. The graphic of Mini-Converter and text below

it provides:

• Type of converter

• Firmware version

• Serial number of the unit.

A status field at the bottom of the screen shows if your application is connected

and communicating with the Mini-Converter.

When configuring the Mini-Converter, select it from the top pulldown, view the

current settings and change any values. Making a change communicates that

new value to the Mini-Converter’s non-volatile memory.

Tabbed Screens

The Tabs delineate control screens with groups of controls for each type of task to

be performed. The controls for the actual configuration parameters are specific

to each Mini-Converter type. When you Click on any of the tab buttons, the pane

below the tabs will change to match your tab selection. Any changes you make

are immediately applied and will be saved, overwriting previous settings.

12GM Mini-Converter v1.6r1 12 www.aja.com

Input Tab Screen

Figure 7. Example of Input Tab Screen showing Quad 3G-SDI to Single 12G-SDI

conversion using Square Division (Quadrant) to Two Sample Interleave (2SI)

pixel mapping.

Click on the Input tab to view and make changes to the converter’s input settings.

Input SDI

Selects the input video format. Choose from the following:

Auto - Automatically selects the format based on the detected input video

parameters. To the right of the drop-down menu, the status display reflects

the current Input SDI behavior.

In order for "Auto" to select Quad Link (SDI 1-4), all four inputs must match in

terms of data rate, link mapping, raster, frame rate, scan type, sampling, bit

depth, and pixel mapping.

Single Link (SDI 1) - Select this option if you have a Single Link UltraHD/4K signal

coming in through SDI In 1.

Single Link (SDI 2) - Select this option if you have a Single Link UltraHD/4K signal

coming in through SDI In 2.

Single Link (SDI 3) - Select this option if you have a Single Link UltraHD/4K signal

coming in through SDI In 3.

Single Link (SDI 4) - Select this option if you have a Single Link UltraHD/4K signal

coming in through SDI In 4.

Quad Link (SDI 1-4) - Select this option if you have a Quad Link UltraHD/4K signal

coming in through SDI In 1-4.

Input Mapping

NOTE: Input pixel mapping applies only to 4K/UltraHD signals being transported on

Quad Link 4 x 3G inputs, as 6G and 12G SDI are always Two Sample Interleave

(2SI), and Quad Link 1.5G SDI is always Square Division (Quadrant).

12GM Mini-Converter v1.6r1 13 www.aja.com

For 4K/UltraHD signals using Quad Link 3Gbps transport, the Video Payload

Identifier (VPID) embedded in each link indicates whether the pixel mapping

is 2SI or not. If 2SI is not indicated, the 12GM assumes that the input signal is

mapped Square Division (Quadrant). Note that there are no specific VPID bits to

indicate Square Division (Quadrant).

Use the Input Mapping control to select the input mapping. Choose from the

following:

Auto - Analyzes details of each input. The VPID from each input signal indicates

whether its pixel mapping is Two Sample Interleave (2SI) or Square Division

(Quadrant).

In order for "Auto" to select 2SI pixel mapping, the video input (whether

single link 6G-SDI or 12G-SDI, or Quad Link 3G-SDI) must indicate 2SI with its

embedded VPID(s).

2SI - Select this option if you are inputting a Two Sample Interleave (2SI) pixel

mapped signal.

SQD - Select this option if you are inputting a Square Division (Quadrant) pixel

mapped signal.

Figure 8. Example of Input Tab Screen showing Single 12G-SDI to Quad 3G-SDI

conversion.

12GM Mini-Converter v1.6r1 14 www.aja.com

Input Detail Tab Screen

Figure 9. Example of Input Detail Tab Screen showing Single 12G-SDI to Quad

3G-SDI conversion.

Figure 10. Example of Input Detail Tab Screen showing Quad 3G-SDI to

Single 12G-SDI conversion using Square Division (Quadrant) to Two Sample

Interleave (2SI) pixel mapping.

Click on the Input Details tab to view detailed input signal diagnostic information.

This can be useful for trouble-shooting and debugging. Input details detected

include Status, Standard, Scan Type, Frame Rate, Data Rate, Level, Sampling, Bit

Depth, and Mapping for each input BNC.

12GM Mini-Converter v1.6r1 15 www.aja.com

Timing Tab Screen

Figure 11. Example of Timing Tab Screen showing Quad 3G-SDI to Single

12G-SDI conversion using Square Division (Quadrant) to Two Sample

Interleave (2SI) pixel mapping.

The purpose of the Timing Tab Screen is to validate that all four links of a Quad

Link input signal meet the required 400ns link-to-link timing, and if not, which

link(s) are not meeting this specification.

The Timing Tab Screen measures timing differences link to link, but displays

timing values relative to SDI 1 for ease of understanding and correcting timing

issues. If the SDI In 1, 2, 3, and 4 links are within +/- 400ns relative to each other,

then the text will be blue. If two or more links are determined to be more than

+/- 400ns relative to each other, then the text is red. The Timing analyzer has a

measurement range of +/- 1/2 frame.

The first row of the Pixels Timing information indicates any horizontal offset

in terms of pixels for each link, while the second row of the Pixels Timing

information indicates the horizontal offset in terms of microseconds. The two

rows display the same information represented in different terms (pixels versus

microseconds). The pixel information (pixels and time) indicates offset of up to 1

line. If the offset exceeds 1 line, then the line count is incremented.

The Total row displays each link's total offset (vertical timing plus horizontal

offset) in terms of time.

12GM Mini-Converter v1.6r1 16 www.aja.com

Figure 12. Example of Timing Tab Screen showing Quad 3G-SDI to Single

12G-SDI conversion using Square Division (Quadrant) to Two Sample

Interleave (2SI) pixel mapping. In this example, a timing error message

displays.

The above Timing Tab Screen shows that links 2, 3, and 4 are equally advanced

with respect to link 1 by about 60 pixels. Since all three links are equally

advanced, most likely link 1 has an additional function element (piece of

processing equipment or additional processing function) which is delaying it 60

lines—so links 2, 3, and 4 appear advanced.

To solve this error, the signal chain feeding SDI Input 1 needs to be analyzed

to determine the cause of the delay. Once found, the delay should be reduced

enough so that it is less than 400ns between links 1 and 2, 1 and 3, and 1 and 4.

12GM Mini-Converter v1.6r1 17 www.aja.com

Output Tab Screen

Figure 13. Example of Output Tab Screen showing Quad 3G-SDI to Single

12G-SDI conversion using Square Division (Quadrant) to Two Sample

Interleave (2SI) pixel mapping.

Click on the Output tab to view and make changes to the converter’s output

settings.

Output SDI

Auto - Automatically selects the output format based on the inputs detected.

If Quad Link UltraHD/4K (SDI 1-4) is detected on the input, the output will

auto-select to a Single Link (SDI 1) multiplex output.

If Single Link UltraHD/4K (SDI 1) is detected on the input, the output will auto-

select to a Quad Link (SDI 1-4) to demux the signal to four outputs using SDI

Outputs 1-4.

Single Link (SDI 1) - Causes the 12GM to use only SDI Output 1. The combination

of input and output settings determines whether the 12GM is muxing,

demuxing or passing through.

Quad Link (SDI 1-4) - Causes the 12GM to use SDI Outputs 1-4, if possible. The

combination of input and output settings determines whether the 12GM is

muxing, demuxing or passing through.

Output Mapping

NOTE: Output pixel mapping applies only to 4K/UltraHD signals being transported

on Quad Link 4x 3G outputs. 6G and 12G SDI are always Two Sample

Interleave (2SI), and Quad Link 1.5G SDI is always Square Division (Quadrant).

Selects the output mapping for Quad Link 4x 3G outputs. Choose from the

following:

Auto - Automatically selects the output pixel mapping based on the input pixel

mapping detected.

12GM Mini-Converter v1.6r1 18 www.aja.com

If Quad Link UltraHD/4K (SDI 1-4) 2SI is detected on the input, the output pixel

mapping will be SQD.

If Quad Link UltraHD/4K (SDI 1-4) SQD is detected on the input, the output

pixel mapping will be 2SI.

If Dual Link UltraHD/4K (SDI 1-4) 1.5G SQD is detected on the input, the output

pixel mapping will be 6G 2SI.

If Quad Link UltraHD/4K (SDI 1-4) SQD or 2SI 3G is detected on the input, the

output pixel mapping will be 12G 2SI.

If Dual Link UltraHD/4K (SDI 1-4) 6G is detected on the input, the output pixel

mapping will be Quad 1.5G SQD.

If Single Link UltraHD/4K (SDI 1-4) 12G is detected on the input, the output

pixel mapping will be Quad 3G 2SI.

2SI - Causes the 12GM to output a Two Sample Interleave (2SI) pixel mapped

signal.

SQD - Causes the 12GM to output a Square Division (Quadrant) pixel mapped

signal.

3G-SDI Mode

The 12GM's 3G-SDI Mode offers the choice between Auto, Level A and Level B-DL.

Auto - The 12GM will automatically select Level A or Level B-DL based on the

inputs detected.

• For Single Link 12G input, Auto will select 4x 3G Level A for the output.

• For a Single Link 6G input, Auto will select 4x 1.5G for the output.

• For a Single Link 3G Level A input, Auto will select 2x 3G Level B-DL for

the output.

Level A - The SDI Outputs will carry a 3G-SDI Level A signal to support these

configurations:

• 4x 3G-SDI Level B-DL to 4x 3G-SDI Level A

• 1.5G-SDI to 3G-SDI Level A

Level B-DL - The SDI Outputs will carry a 3G-SDI Level B-DL signal to support

these configurations:

• 12G-SDI to 4x 3G-SDI Level B-DL

• 4x 3G-SDI Level A to 4x 3G-SDI Level B-DL

• 3G-SDI Level A to 1.5G-SDI

DA Function

The 12GM's Distribution Amplifier (DA) function is available for Single Link output

signals.

On - When turned on, the DA function will duplicate SDI Output 1's signal on SDI

Outputs 2, 3, and 4.

NOTE: If the output is a Quad Link signal, the DA function is overridden and turned

off.

Off - When turned off, no signal duplication will occur.

12GM Mini-Converter v1.6r1 19 www.aja.com

Figure 14. Example of Output Tab Screen showing the output set to Single Link

12G-SDI. The DA Function is turned on, duplicating the 12G-SDI input signal

and sending it out through all four SDI outputs.

Output Detail Tab Screen

Figure 15. Example of Output Detail Tab Screen showing Quad 3G-SDI to

Single 12G-SDI conversion using Square Division (Quadrant) to Two Sample

Interleave (2SI) pixel mapping.

Click on the Output Details tab to view detailed output signal diagnostic

information. This can be useful for trouble-shooting and debugging. Output

12GM Mini-Converter v1.6r1 20 www.aja.com

signal details include Status, Standard, Scan Type, Frame Rate, Data Rate, Level,

Sampling, Bit Depth, and Mapping for each output BNC.

Figure 16. Example of Output Detail Tab Screen showing Single 12G-SDI to

Quad 3G-SDI conversion using Square Division (Quadrant) to Two Sample

Interleave (2SI) pixel mapping.

Update Tab Screen

Use this Update tab screen to view the software version currently installed on the

converter or to install new software.

La pagina si sta caricando...

AJA 12GM Manuale utente

Marca: AJA

Modello: 12GM

Categoria: Convertitori video

Tipo: Manuale utente

Scarica PDF

rapporto

in altre lingue

Documenti correlati

Altri documenti

Elvox 46364.001 Istruzioni per l'uso