ProLights 100 W Daylight White COB PAR Manuale utente

Marca: ProLights

Modello: 100 W Daylight White COB PAR

Categoria: Proiettori

Tipo: Manuale utente

Questo manuale è adatto anche per

USER MANUAL

MANUALE UTENTE

STUDIOCOB TU-DY

EN - IT

DIFFUSED LIGHT PROJECTOR

STUDIOCOB TU-DY

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV.02-06/18

STUDIOCOB TU-DY

Packing content

STUDIOCOB

• Power cable

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Auto show

3. 5 Static mode

3. 6 Master/Slave mode

3. 7 Linking

3. 8 DMX conguration

3. 9 DMX addressing

3. 10 Connection of the DMX line

3. 11 Construction of the DMX termination

3. 12 DMX control

3. 13 Fixture settings

3. 14 Fixture information

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Fuse replacement

4. 3 Trouble shooting

STUDIOCOB TU-DY

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bu mps;

- in places with a temperature of over 45 °C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

• Do not touch the product’s housing when operating because it may be very hot.

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

STUDIOCOB TU-DY

- 1 - INTRODUCTION

1.1 DESCRIPTION

STUDIOCOBTU is a powerful and incredibly versatile LED PAR. Fusing the old and the new, it pairs a 3100K

COB LED source with a traditional parabolic reector to deliver a proper PAR replacement with a homog-

enised output, single shadow and exible lens options.

STUDIOCOBDY is a powerful and incredibly versatile LED PAR. Fusing the old and the new, it pairs a 5000K

COB LED source with a traditional parabolic reector to deliver a proper PAR replacement with a homog-

enised output, single shadow and exible lens options.

1.2 TECHNICAL SPECIFICATIONS

LIGHT SOURCE TU

• Source: 100W High Power White LED

• CT: 3100K

• CRI: 94

• R9: 72

• Luminous Flux: 5221lm

• Lux: (30°) 1404lux @3m

• Source Life Expectancy: >30.000 h

• Other: TLCI (Qa):96.5

OPTICS

• Beam Angle: 60°

• Field Angle: 80°

• Lens Type: Dichroic parabolic reector in combi-

nation with HD fresnel lens

• Additional Optics: 30° (inc) - 15° (opt)

DYNAMIC EFFECTS

• Static Color Mode: Selection of static color

• Manual Color Mode: Manual adjustment of dim-

mer and strobe

• Auto Mode: Built-in programs with execution

speed adjustment

BODY

• Body: Sturdy die-cast aluminium body conceived

for long-time durability

• Body Color: Black, Mirror and White nishing

available

CONTROL

• Protocols: DMX512

• DMX Channels: 1/2/5ch

• Display: Black OLED high resolution display

• Firmware Upgrade: Yes, via USB-DMX interface

(UPBOX1) not included

• Master/Slave: for synchronized operation of

LIGHT SOURCE DY

• Source: 100W High Power White LED

• CT: 5000K

• CRI: 83

• R9: 82,6

• Luminous Flux: 5290lm

• Lux: (30°) 1940lux @3m

• Source Life Expectancy: >30.000 h

• Other: TLCI (Qa):68.7

OPTICS

• Beam Angle: 60°

• Field Angle: 80°

• Lens Type: Dichroic parabolic reector in combi-

nation with HD fresnel lens

• Additional Optics: 30° (inc) - 15° (opt)

DYNAMIC EFFECTS

• Static Color Mode: Selection of static color

• Manual Color Mode: Manual adjustment of dim-

mer and strobe

• Auto Mode: Built-in programs with execution

speed adjustment

BODY

• Body: Sturdy die-cast aluminium body conceived

for long-time durability

• Body Color: Black, Mirror and White nishing

available

CONTROL

• Protocols: DMX512

• DMX Channels: 1/2/5ch

• Display: Black OLED high resolution display

• Firmware Upgrade: Yes, via USB-DMX interface

(UPBOX1) not included

• Master/Slave: for synchronized operation of

STUDIOCOB TU-DY

Fig.1

Technical drawing

190

262

371

more units linked in a chain

ELECTRONICS

• Dimmer: Linear 0~100% electronic dimmer

• Dimmer Curves: 4 Dierent dimming curves

available

• Strobe/Shutter: 1-28 Hz, electronic

• Operating Temperature: -10° ~ +45°

• Flicker: Flicker free operation

• Selectable PWM: 600~25K Hz

ELECTRICAL

• Power Supply: 100-240V – 50/60Hz

• Power Consumption (at 230V): 102W

• Power Consumption (at 120V): 102W

• Output (at 230V): 12 units on a single power line

• Power factor: 0,9331

PHYSICAL

• Cooling: Forced air with low noise fan

• Suspension And Fixing: Double hanging bracket

suitable for safe hanging and for oor position-

ing

• Signal Connection: 3p+5p in/out

• Power Connection: PowerCON in/out

• IP: 20

• Dimensions (WxHxD): 262x190x371mm

• Weight: 4,5kg

STUDIOCOB TU-DY

1.3 OPERATING ELEMENTS AND CONNECTIONS

1. LOCKING KNOB for the mounting bracket

2. MOUNTING BRACKET

3. DMX IN (3-pole XLR):

1 = ground, 2 = DMX -, 3 = DMX +

4. DMX OUT (3-pole XLR):

1= ground, 2 = DMX -, 3 = DMX +

5. CONTROL PANEL with display and 4 button

used to access the control panel functions

and manage them

6. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

Rear panel Fig.2

7. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+, 4 N/C, 5 N/C

8. POWER IN (PowerCON IN): for connection to a

socket (100-240V~/50-60Hz) via the supplied

mains cable

9. MAIN FUSE HOLDER: replace a burnt-out fuse

by one of the same type only (T2A 250V)

10. GND POINT grounding the xture to the earth

11. SAFETY RING to attach safety cable

12. POWER OUT: connect to supply power to the

next unit

10 11

STUDIOCOB TU-DY

- 2 - INSTALLATION

2.1 MOUNTING

STUDIOCOB may be set up on a solid and even surface. The unit can also be mounted upside down to a

cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability

and be able to support a weight of 10 times of the unit’s weight.

When carrying out any installation, always comply scrupulously with all the regulations (particularly re-

garding safety) currently in force in the country in which the xture’s being used.

• Install the projector at a suitable location by means of the mounting bracket (2).

• Always additionally secure the projector with the safety rope from falling down. For this purpose, fas-

ten the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.

• Adjust the projector and use the screw to slightly release or tighten the locking mechanism of the

bracket if is necessary (1).

Fig.3

STUDIOCOB TU-DY

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). Then the unit is ready for operation

and can be operated via a DMX controller or it independently performs its show program in succession.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via a light switch.

3.2 BASIC

Access control panel functions using the four panel buttons located directly underneath the black OLED

display (g.4).

Fig.4 - Functions of the buttons

MENU UP DOWN ENTER

Used to access the menu or

to return a previous menu

option

Navigates downwards through

the menu list and increases

the numeric value when in a

function

Navigates upwards through

the menu list and decreases

the numeric value when in

a function

Used to select and store the

current menu or conrm the

current function value or

option within a menu

MENU UP DOWN ENTER

STUDIOCOB TU-DY

3.3 MENU STRUCTURE

1 Auto Show

Auto 1

Speed (0-100)

Auto 2

Speed (0-100)

Auto 3

Speed (0-100)

2 Static

Dimmer

0 - 255

Strobe

0 - 255

3 Dimmer Mode

O

Dimmer 1

Dimmer 2

Dimmer 3

4 Back Light

10 S

20 S

30 S

5 Information

Fixture Hours

9999

Version

V1.0

6 DMX Address

1 - 512

7 DMX Channel

1 Ch

2 Ch

5 Ch

8 Master/Slave

Master

Slave

9 Fan mode

auto/high

10 LED Frequency

600 Hz

1200 Hz

2000 Hz

4000 Hz

25 kHz

11 Temperature

40°C

STUDIOCOB TU-DY

3.4 AUTO SHOW

If no DMX control signal is present at the DMX INPUT, the unit independently runs through its show pro-

gramme provided that the blackout mode is switched o:

• Press the button MENU so many times until the display shows Auto Show, then press the button ENTER.

• Press the button UP/DOWN to switch between the show Auto 1 - Auto 3. The unit will operate in show

mode.

• Using the button UP/DOWN to select the desired run speed slow-fast 0-100.

• Press the button ENTER to save the setting.

IMPORTANT: Programs Auto 1 - 3 are fully pre-programmed and will not be altered by changes. Instead,

3.5 STATIC MODE

Allows you to create ranges of eects by combining channels Dimmer - Strobe.

• Press the button MENU so many times until the display shows Static, then press the button ENTER.

• Select Dimmer - Strobe through the buttons UP/DOWN.

• Press the button ENTER to conrm.

• Set the value 000 - 255, through the buttons UP/DOWN.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

3.6 MASTER/SLAVE MODE

This mode will allow you to link up the units together without a controller. Choose a unit to function as the

Master. The unit must be the rst unit in line; other units will work as slave with the same eect.

• Press the button MENU so many times until the display shows Master/Slave and press the button ENTER.

• Press UP/DOWN to set the unit as master or slave (Master/Slave).

• Select the desired program (see section 3.4).

• Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the

units. For longer cable runs we suggest a terminator at the last xture (see page 12).

3.7 LINKING

1. Connect the DMX OUT of the master unit via 3/5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

3.8 DMX CONFIGURATION

STUDIOCOB is equipped with dierent DMX conguration.

• Press the button MENU so many times until shows DMX Channel, and press the button ENTER to conrm.

• Select the desired DMX conguration (1CH - 2CH - 5CH) through the buttons UP/DOWN.

The tables on page 13 indicate the operating mode and DMX value. The STUDIOCOB is equipped with

3/5-pole XLR connections.

3.9 DMX ADDRESSING

• Press the button MENU so many times until the display shows DMX Address, and press the button ENTER

to conrm.

• Press UP/DOWN button to select the desired value (001-512). Press and hold to scroll quickly.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

STUDIOCOB TU-DY

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

5 33 33-37 38 43 48

To able to operate the STUDIOCOB with a light controller, adjust the DMX start address for the rst a

DMX channel. If e. g. address 33 on the controller is provided for controlling the function of the rst DMX

channel, adjust the start address 33 on the STUDIOCOB.

The other functions of the light eect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

. . . . . . . . . . . .

DMX512 Controller

DMX Address: 33 DMX Address: 48DMX Address: 38 DMX Address: 43

Fig.5 - Example 5 DMX channels conguration

STUDIOCOB TU-DY

Fig.6

Fig.7

3.10 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.11 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

Example:

3 pin XLR connector

STUDIOCOB TU-DY

3.12 DMX CONTROL

1 CHANNEL

MODE

FUNCTION DMX

Value

1 Ch

DIMMER

0~100% 000 - 255

5 CHANNELS

MODE

FUNCTION DMX

Value

5 Ch

DIMMER

0~100% 000 - 255

STROBE

No Function

Slow to fast

000 - 010

011 - 255

AUTO PROGRAMS

No Function

Auto Program 1

Auto Program 2

Auto Program 3

000-010

011-090

091-170

171-255

AUTO SPEED

Slow to fast 000 - 255

DIMMER SPEED

Preset dimmer speed from display menu

Dimmer speed mode o

Dimmer speed mode1 (fast speed)

Dimmer speed mode2 (middle speed)

Dimmer speed mode3 (slow speed)

000-051

052-101

102-152

153-203

204-255

2 CHANNELS

MODE

FUNCTION DMX

Value

2 Ch

DIMMER

0~100% 000 - 255

STROBE

No function

Strobe Slow to Fast

000 - 010

011 - 255

STUDIOCOB TU-DY

3.13 FIXTURE SETTINGS

It is possible to change the parameter value in the following way:

Dimmer

• Enter in Dimmer mode to select specic dimming curve, press the button MENU so many times

until shows Dimmer Mode, and press the button ENTER to conrm.

• Press the button UP/DOWN to select O - Dimmer 1 - Dimmer 2 - Dimmer 3.

• Press ENTER button to store.

• Press the MENU button to go back or to meet the waiting time to exit the setup menu.

BackLite

• To activate Backlight display press the button MENU so many times until shows Back Light, and press

the button ENTER to conrm.

• Press the button UP/DOWN to select On - 10S - 20S - 30S.

• Press ENTER button to conrm the selection.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu auto-

matically.

LED Frequency

• To adjust the frequency of the LEDs, press the MENU button repeatedly until the display shows LED

Frequency, and then press the ENTER button.

• Select the frequency (600 Hz - 1200 Hz - 2000 Hz - 4000 Hz - 25 kHz) using the UP/DOWN buttons.

• To conrm, press the ENTER key.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

Fan Mode

• To set the rotation speed of the fans refer to the following guide:

• Press the MENU key repeatedly until the display shows Fan Mode, then press the button ENTER.

• Select by pressing UP/DOWN one of the following options: Auto - High. It is possible choose the

speed of rotation of the fans from: fast High and automatic Auto.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

3.14 FIXTURE INFORMATION

Fixture Hours

Show the xture working hours.

• Press the button MENU so many times until shows Information. Press the button ENTER to conrm

• Using the button UP/DOWN to select Fixture Hours, then press the button ENTER to conrm

• Then the display will show the working hours.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu auto-

matically

Version

Show the xture rmware version.

• Press the button MENU so many times until shows Information

• Select through the button UP/DOWN the Version menu voice.

• The display will show the rmware data.

• Press the MENU button to go back or to meet the waiting time to exit from the setup menu automatically.

STUDIOCOB TU-DY

Temperature

• To read the value of the internal temperature of the device, press the MENU button repeatedly until

the display shows Temperature, and then press the ENTER button to read the value.

• Press the MENU button to go back or wait a few seconds to exit the setup menu.

STUDIOCOB TU-DY

- 4 - MAINTENANCE

4.1 MAINTENANCE AND CLEANING THE UNIT

• Make sure the area below the installation place is free from unwanted persons during setup.

• Switch o the unit, unplug the main cable and wait until the unit has cooled down.

• All screws used for installing the device and any of its parts should be tightly fastened and should not

be corroded.

• Housings, xations and installation spots (ceiling, trusses, suspensions) should be totally free from any

deformation.

• The main cables must be in impeccable condition and should be replaced immediately even when a

small problem is detected.

• It is recommended to clean the front at regular intervals, from impurities caused by dust, smoke, or

other particles to ensure that the light is radiated at maximum brightness. For cleaning, disconnect the

main plug from the socket. Use a soft, clean cloth moistened with a mild detergent. Then carefully wipe

the part dry. For cleaning other housing parts use only a soft, clean cloth. Never use a liquid, it might

penetrate the unit and cause damage to it.

4.2 FUSE REPLACEMENT

1. Disconnect this product from the power outlet.

2. Using a screwdriver, unscrew the fuse holder cap from the housing.

3. Remove the blown fuse and replace with a good fuse of the same type and rating

(250V/T2A).

4. Screw the fuse holder cap back in place and reconnect power.

4.3 TROUBLESHOOTING

Fig.8

Problems Possible causes Checks and remedies

Fixture does not light up

• No mains supply

• Dimmer fader set to 0

• All color faders set to 0

• Faulty LED

• Faulty LED board

• Check the power supply voltage

• Increase the value of the dimmer channels

• Increase the value of the color channels

• Replace the LED board

General low light intensity

• Dirty lens assembly

• Misaligned lens assembly

• Clean the xture regularly

• Install lens assembly properly

Fixture does not power up

• No power

• Loose or damaged power cord

• Faulty internal power supply

• Check for power on power outlet

• Check power cord

• Replace internal power supply

Fixture does not respond to DMX

• Wrong DMX addressing

• Damaged DMX cables

• Bouncing signals

• Check control panel and unit addressing

• Check DMX cables

• Install terminator as suggested

Contact an authorized service center in case of technical problems or not reported in the table can not be

resolved by the procedure given in the table.

Music & Lights S.r.l. si riserva ogni diritto di elaborazione in qualsiasi forma delle presenti istruzioni per l’uso.

La riproduzione - anche parziale - per propri scopi commerciali è vietata.

Al ne di migliorare la qualità dei prodotti, la Music&Lights S.r.l. si riserva la facoltà di modicare, in

qualunque momento e senza preavviso, le speciche menzionate nel presente manuale di istruzioni.

Tutte le revisioni e gli aggiornamenti sono disponibili nella sezione 'Manuali' sul sito www.musiclights.it

STUDIOCOB TU-DY

• STUDIOCOB

• Cavo di alimentazione

• Manuale utente

Contenuto dell'imballo:

INDICE

Sicurezza

Avvertenze generali

Attenzioni e precauzioni per l’installazione

1 Introduzione

1. 1 Descrizione

1. 2 Speciche tecniche

1. 3 Elementi di comando e di collegamento

2 Installazione

2. 1 Montaggio

3 Funzioni e impostazioni

3. 1 Funzionamento

3. 2 Impostazione base

3. 3 Struttura menu

3. 4 Modalità automatica

3. 5 Modalità static

3. 6 Modalità Master/Slave

3. 7 Collegamento

3. 8 Congurazione canali DMX

3. 9 Indirizzamento DMX

3. 10 Collegamenti della linea DMX

3. 11 Costruzione del terminatore DMX

3. 12 Canali DMX

3. 13 Funzioni dispositivo

3. 14 Informazioni sul dispositivo

4 Manutenzione

4. 1 Manutenzione e pulizia del sistema ottico

4. 2 Sostituzione fusibile

4. 3 Risoluzione dei problemi

STUDIOCOB TU-DY

ATTENZIONE! Prima di effettuare qualsiasi operazione con l’unità, leggere con attenzione

questo manuale e conservarlo accuratamente per riferimenti futuri. Contiene informazioni

importanti riguardo l’installazione, l’uso e la manutenzione dell’unità.

SICUREZZA

Avvertenze generali

• I prodotti a cui questo manuale si riferisce sono conformi alle Direttive della Comunità Europea e per-

tanto recano la sigla .

• Il dispositivo funziona con pericolosa tensione di rete 230V~. Non intervenire mai al suo interno al di

fuori delle operazioni descritte nel presente manuale; esiste il pericolo di una scarica elettrica.

• È obbligatorio eettuare il collegamento ad un impianto di alimentazione dotato di un’eciente messa

a terra (apparecchio di Classe I secondo norma EN 60598-1). Si raccomanda, inoltre, di proteggere le

linee di alimentazione delle unità dai contatti indiretti e/o cortocircuiti verso massa tramite l’uso di

interruttori dierenziali opportunamente dimensionati.

• Le operazioni di collegamento alla rete di distribuzione dell’energia elettrica devono essere eettuate

da un installatore elettrico qualicato. Vericare che frequenza e tensione della rete corrispondono alla

frequenza ed alla tensione per cui l’unità è predisposta, indicate sulla targhetta dei dati elettrici.

• L’unità non per uso domestico, solo per uso professionale.

• Evitare di utilizzare l’unità:

- in luoghi soggetti a vibrazioni, o a possibili urti;

- in luoghi a temperatura superiore ai 45°C.

• Evitare che nell’unità penetrino liquidi inammabili, acqua o oggetti metallici.

• Non smontare e non apportare modiche all’unità.

• Tutti gli interventi devono essere sempre e solo eettuati da personale tecnico qualicato. Rivolgersi al

più vicino centro di assistenza tecnica autorizzato.

• Se si desidera eliminare il dispositivo denitivamente, consegnarlo

per lo smaltimento ad un’istituzione locale per il riciclaggio.

Attenzioni e precauzioni per l’installazione

• Se il dispositivo dovesse trovarsi ad operare in condizioni dierenti da quelle descritte nel presente

manuale, potrebbero vericarsi dei danni; in tal caso la garanzia verrebbe a decadere. Inoltre, ogni altra

operazione potrebbe provocare cortocircuiti, incendi, scosse elettriche, rotture etc.

• Prima di iniziare qualsiasi operazione di manutenzione o pulizia sull’unità togliere la tensione dalla rete

di alimentazione.

• È assolutamente necessario proteggere l’unità per mezzo di una fune di sicurezza. Nell’eseguire qual-

siasi intervento attenersi scrupolosamente a tutte le normative (in materia di sicurezza) vigenti nel

paese di utilizzo.

• Installare l’unità in un luogo ben ventilato.

• Mantenere i materiali inammabili ad una distanza di sicurezza dall’unità.

• I ltri, le lenti o gli schermi ultravioletti se danneggiati possono limitare la loro ecienza.

• I LED devono essere sostituiti se danneggiati o termicamente deformati.

• Non guardare direttamente il fascio luminoso. Tenete presente che i veloci cambi di luce possono pro-

vocare attacchi d’epilessia presso persone fotosensibili o epilettiche.

• Non toccare l’alloggiamento del prodotto quando è in funzione perché potrebbe essere molto caldo.

La pagina si sta caricando...

ProLights 100 W Daylight White COB PAR Manuale utente

Marca: ProLights

Modello: 100 W Daylight White COB PAR

Categoria: Proiettori

Tipo: Manuale utente

Questo manuale è adatto anche per

Scarica PDF

rapporto

in altre lingue

English: ProLights 100 W Daylight White COB PAR User manual

Documenti correlati

Altri documenti

Coemar DIGIfactor club 6x2,5Kw Manuale utente