NEC WT600 Manuale del proprietario

[English]

WT600 SETUP GUIDE

[Deutsch]

AUFSTELLUNGSANLEITUNG WT600

[Français]

WT600 - GUIDE D’INSTALLATION

[Italiano]

GUIDA DI IMPOSTAZIONE WT600

[Español]

GUÍA DE INSTALACIÓN DE LA UNIDAD WT600

[Svenska]

WT600 INSTALLATIONSGUIDE

WT600 SETUP GUIDE

Contents

Screens Suited for the WT600 ........................................... E-2

Stands Suited for the WT600 ............................................. E-2

Ambient environmental condition ....................................... E-3

Part Names of the Projector ............................................... E-3

1. Setting Up the Screen and Projector .............................. E-4

2. Connections ................................................................... E-5

3. Opening the Mirror ......................................................... E-5

4. Switchng on the Power ................................................... E-6

5. Selecting Signals ............................................................ E-6

6. Adjusting the Position and Size of the Projected Image

(Focus Adjustments) ....................................................... E-7

7. Adjusting Pincushion or Barrel Distortion

(Pincushion) .................................................................. E-11

8. Troubleshooting ............................................................ E-13

P

O

W

E

R

E

N

T

E

R

M

E

N

U

S

O

U

R

C

E

F

O

C

U

S

P

C

A

R

D

C

A

N

C

E

L

S

T

A

TU

S

L

A

M

P

O

N

/

S

T

A

N

D

B

Y

A

U

TO

A

D

JU

S

T

3

D

R

E

F

O

R

M

S

E

LE

C

T

PC C

AR

D

A

U

D

IO

IN

R

L

/M

O

N

O

VIDEO IN

S-V

IDEO

IN

DV

I-I IN

R

GB

IN RGB OUT

DV

I-I

RGB

AUDIO IN

USB

AUD

IO OUT

P

C

CON

TROL

REM

OTE

IN

NOTE

(1) The contents of this guide may not be reprinted in part or whole without permission.

(2) The contents of this guide are subject to change without notice.

(3) Great care has been taken in the creation of this guide; however, should any ques-

tionable points, errors, or omissions be apparent, please contact us.

(4) Notwithstanding Section (3), this company will not be responsible for any claims of

loss or profit or other matters deemed to be the result of using this unit.

(5) Guides with incorrect collating or missing pages will be replaced.

(6) When differences arise between this guide and the user's manual, this guide will be

given priority.

Scope of this Guide

The subject of this guide is to describe the procedure for adjusting the

image projected from the WT600 to the desired screen size. Descrip-

tions of screens and stands for use with the WT600 are also provided.

Please see the user's manual for information regarding the detailed

operation of the WT600 (hereafter referred to as "the unit" or "the pro-

jector").

E-1

WARNING

• Do not set up the projector, the screen or stand in a place that is not level or in an

unstable location. Doing so may result in the screen falling over or the projector falling

which may result in injury.

• When setting up the projector on the stand, first secure the top plate in a level condi-

tion. When the top plate is set at an angle, the projector may fall resulting in injury.

• Use a stand that can fully support the weight of the projector (which for this unit is

approximately 13lbs/5.9 kg). Failing to do so may result in the projector falling and

causing injury.

E-2

40"-100"

90˚

Screens Suited for the WT600

• Screens with a soiled, scratched, or discolored area will not produce a clean

image. Care should be used in the handling of the screen.

Recommended

Not recommended

Recommended

Not recommended

Recommended

Not recommended

Not optimal

Not recommended

• Use a panel or tension type screen that has a flat surface.

Do not use roll type screens and other screens that bend or

form a wavy surface easily. Doing so will result in increased

distortion of the projected image.

• The unit can accommdate screen sizes from 40” (81.3 cm/32.0” W ⳯ 61.0

cm/24.0” H) to 100 inch (203.2 cm/80.0” W ⳯ 152.4 cm/60.0” H).

• View the screen directly from the side so that it is perfectly

vertical.

A slanted screen will result in increased keystone distortion.

• In using this unit, increasing the screen size will move the projection position

upward. To accommodate this, please use a screen that has higher and lower

positioning adjustment. See Page 4 for information about the positioning rela-

tionships between the screen and this unit.

• High gain type screens are not optimal for use with this unit. The lower the

screen gain (i.e., screen gain on the order of 1), the better the appearance of

the projected image.

For more information about screen gain, consult catalogs from screen mak-

ers.

• Screen frames or pen shelves that protrude from the front of the screen sur-

face may block some of the light from the projector.

• Due to the projection angle of the unit, many standard rear projection screens

may produce uneven brightness, hot spotting or not produce maximum bright-

ness to the viewer. For more details utilizing rear projection screens and their

applications with this projector, please contact your NEC dealer.

• Controlled ambient light environments will allow for an image of higher con-

trast and depth to be displayed.

Level

Stands Suited for the WT600

• Use a stand that will allow this unit to be set up in a level condition. Turn the

foot of this unit and adjust so that the unit is level.

Recommended

• In using this unit, increasing the screen size will move the projection position

upward. To accommodate this, please use a stand that has a height position-

ing adjustment. See Page E-4 for information about the positioning relation-

ships between the screen and this unit.

E-3

Ambient environmental condition

• Do not place the screen near vents.

Air blow hits the screen, causing the projected image to ripple.

PO

W

ER

ENTER

M

EN

U

SOU

R

CE

FO

C

US

PC C

ARD

CANC

EL

STATUS

LAMP

ON/

STAND

B

Y

AU

TO

A

DJU

ST

3D

R

EFO

RM

SELECT

P

C

A

R

D

A

U

D

I

O

I

N

R

L

/

M

O

N

O

V

ID

E

O

IN

S

-V

ID

E

O

IN

D

V

I-I IN

R

G

B

IN

R

G

B

O

U

T

D

V

I-I

R

G

B

A

U

D

IO

IN

U

S

B

A

U

D

IO

O

U

T

P

C

O

N

T

R

O

L

R

E

M

O

T

E

IN

Part Names of the Projector

Front view

Rear view

Mirror cover

Open the mirror cover first before projecting an im-

age. See page E-5.

Avoid opening or closing the mirror cover quickly and

roughly.

Mirror cover lock switch

Slide this lock switch to the unlock position first before

opening the mirror cover.

After closing the mirror cover, slide the lock switch to

the lock position.

Foot (four feet on bottom)

Adjust the height by rotating each foot to keep the pro-

jector in a horizontal position. Each foot can be ex-

tended up to 1.2"(30mm).

Cabinet controls

The controls on the projector cabinet allows for power

on/off, source selection and other button operations.

See page E-6.

Terminal panel

Connect the RGB signal cable and other cables here.

See page E-5.

Main power switch

To turn on the main power to the projector, press the

Main Power switch to the ON position (l). The projec-

tor is in the Idle or standby mode and becomes ready

to use. See page E-6.

AC IN input

Connect the supplied power cable here. See page E-

5.

Foot (four feet on bottom)

NOTE : For more information on part names of the projector,see page 1-2 of the user's manual.

• Do not illuminate the projector with strong light source such as halogen lamp.

Doing so can cause the object detection sensor to malfunction, resulting in the projector not

turning on.

1. Setting Up the Screen and Projector

1. Refer to "Throw Distance (C)" in the diagram and use a distance between the screen

and projector that corresponds to the screen size.

As an example, when projecting to a 60" screen, set the projector with a separation of

approximately 10.4"/26.3 cm from the screen.

2. Refer to "Height (D)" below and adjust the screen height, or adjust the height of the

projector stand.

As an example, when projecting to a 60" screen, adjust the height from the bottom surface

of the projector to the lower edge of the screen to approximately 19.0"/48.2 cm.

E-4

C

D

Back of

projector

Projector

foot

Screen center

0

20

40

60

80

100

120

051015 20 25 30

Throw distance C (inch)

Screen size (inch)

0

20

40

60

80

100

120

0 100 200 300 400 500 600 700

Throw distance C (mm)

Screen size (inch)

40

45

50

55

60

65

67

70

72

75

78

80

84

85

90

95

96

100

64

114

164

214

263

313

332

362

381

412

441

461

500

510

559

609

619

659

2.5

4.5

6.4

8.4

10.4

12.3

13.1

14.3

15.0

16.2

17.4

18.1

19.7

20.1

22.0

24.0

24.4

25.9

Screen size

(inch)

Throw distance (C)

mm inch

354

386

418

450

482

514

526

546

558

577

596

609

635

641

673

704

711

737

13.9

15.2

16.5

17.7

19.0

20.2

20.7

21.5

22.0

22.7

23.5

24.0

25.0

25.2

26.5

27.7

28.0

29.0

Height (D)

mm inch

Height (B)

mm inch

NOTE

• There is a tolerance of +5% because of design values.

• The projection distance and the lower edge of the

screen are calculated using a 4:3 aspect ratio.

659

729

799

869

939

1010

1037

1080

1107

1149

1191

1219

1275

1289

1359

1428

1443

1499

25.9

28.7

31.5

34.2

37.0

39.7

40.8

42.5

43.6

45.2

46.9

48.0

50.2

50.7

53.5

56.2

56.8

59.0

B

E-5

2. Connections

1. Connect the supplied 15pin-15pin signal cable.

For older Macintosh computers, use a commercially available pin adapter to connect to your

Macintosh’s video port.

NOTE : Power down all equipment before making connections.

P

O

W

E

R

E

N

T

E

R

M

E

N

U

S

O

U

R

C

E

F

O

C

U

S

P

C CA

R

D

C

A

N

C

E

L

S

TA

T

U

S

L

A

M

P

O

N

/

S

T

A

N

D

B

Y

A

U

T

O

A

D

JU

S

T

3

D

R

E

FO

R

M

S

E

L

E

C

T

P

C

A

R

D

A

U

D

I

O

I

N

L

/

M

O

N

O

R

V

I

D

E

O

I

N

S

-

V

I

D

E

O

IN

D

V

I

-

I

N

R

G

B

I

N

R

G

B

O

U

T

D

V

I

-

I

R

G

B

A

U

D

I

O

I

N

U

S

B

A

U

D

I

O

U

T

P

C

O

N

T

R

O

L

R

E

M

O

T

E

IN

RGB IN

RGB signal cable (supplied)

P

O

W

E

R

E

N

T

E

R

M

E

N

U

S

O

U

R

C

E

F

O

C

U

S

P

C

A

R

D

C

A

N

C

E

L

S

T

A

T

U

S

L

A

M

P

O

N

/

S

T

A

N

D

B

Y

A

U

T

O

A

D

J

U

S

T

3

D

R

E

F

O

R

M

S

E

L

E

C

T

PC CAR

D

A

UD

IO IN

R

L

/M

ON

O

VID

EO

IN

S-V

ID

EO

IN

D

V

I-I IN

RG

B IN

RG

B OU

T

D

VI-I R

G

B

AUD

IO IN

U

S

BAU

D

IO

O

U

T

P

C

O

NTR

OL

R

EM

O

TE

IN

2. Connect the supplied power cable.

P

O

W

E

R

E

N

T

E

R

C

A

N

C

E

L

S

T

A

T

U

S

L

A

M

P

O

N

/

S

T

A

N

D

B

Y

A

U

T

O

A

D

J

U

S

T

3

D

R

E

F

O

R

M

S

E

L

E

C

T

R

G

B

IN

R

G

B

O

U

T

D

V

I-

I

R

G

B

A

U

D

IO

IN

U

S

B

A

U

D

IO

O

U

T

PO

W

ER

EN

TER

CAN

CE

L

ST

ATUS

LA

M

P

ON/

STAN

D

BY

AU

TO

ADJU

ST

3D

R

E

FO

RM

SELECT

RGB IN RGB OUT

DVI-I RGB

AUDIO IN

USB

AUDIO OUT

3. Opening the mirror

1. Slide the mirror cover lock switch to the unlock position.

2. Slowly open the mirror cover holding both ends.

NOTE:

• Do not release your hold of the mirror cover until fully open.

• Do not apply excessively strong pressure against the mirror

cover or mirror surface while opening it.

•Keep finger prints off the mirror surface. Leaving finger prints

in the mirror surface might cause an unwanted shadow and

poor picture quality.

If the mirror surface is soiled with finger prints, wipe them off

with the supplied cleaning cloth. See page 7-2 of the user's

manual.

4. Switching on the Power

1. Turn on the main power switch.

ENTER CANCEL

STATUS

LAMP

ON/

STAND BY

AUTO

ADJUST

3D

REFORM

POWER

ENTER CANCEL

STATUS

LAMP

ON/

STAND BY

AUTO

ADJUST

3D

REFORM

POWER

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

OFF

VIDEO

AUTO ADJ.

RGB VIEWER

LASER

ON

SELECT

POWER

2. Turn on the projector.

To turn on the power to the projector, press and hold

the ON/STAND BY button on the projector cabinet or

the POWER ON button on the remote control for a

minimum of 2 seconds.

NOTE : To turn off the projector, press and hold the

ON/STAND BY button or the POWER OFF button for

a minimum of 2 seconds.

Note on Startup screen (Menu Language Select

screen)

When you first turn on the projector, you will get the

Startup screen. This screen gives you the opportu-

nity to select one of the seven menu languages:

English, German, French, Italian, Spanish, Swedish

and Japanese. (See page 3-1 of the user’s manual)

To turn on the main power to the projector,

press the Main Power switch to the ON position

( I ).

NOTE: Before you turn on your projector,

ensure that the computer is turned on.

The POWER indicator will light orange (In the

Idle mode the STATUS indicator will light green

as well). The projector is in the Idle or Standby

mode.

MENU

SOURCE

FOCUS

PC CARD

SELECT

M

E

N

U

E

N

T

E

R

C

A

N

C

E

L

OFF

VIDEO

AUTO ADJ.

RGB VIEWER

LASER

ON

SELECT

POWER

5. Selecting Signals

Press and hold the SOURCE button for a

minimum of 1 second, the projector will search

for the next available input source. When using

the remote control, press the RGB button for the

RGB source.

NOTE:

• When projecting the image from a personal

computer and the image edge is cut off or the

projection is poor, press the AUTO ADJUST

button (which is labeled AUTO ADJ. on the

remote control) and the projector will perform

the adjustment automatically.

• When the image from the personal computer

is not projected, see "Common Problems &

Solutions" on page E-14.

E-6

Projector's left side Cabinet controls

Cabinet controls Remote control

E-7

90˚

1. Check whether the screen is set up to be vertical by

viewing it from the side.

6. Adjusting the Position and Size of the Projected Image

(Focus Adjustments)

• After turning on the power, projected images may flicker for 3 to 5 minutes until the lamp

lighting is stabilized.

Also after turning on the projector, the picture position may be slightly changed.

Wait 10 minutes until the light status and projected images become stable.

• If the screen is tilted vertically or horizontally, keystone distortion becomes large. Proceed the

following steps to correctly set up the projector and the screen.

2. Check that the projector is level and that it is set to

be parallel with the screen.

MENU

SOURCE

FOCUS

PC CARD

SELECT

PJ

ASPECT FREEZE

FOCUS

3D REFORM

HELP

POINTER

VOLUME MAGNIFY

ZOOM

PIC-MUTE

SLIDE

FOLDER

SLIDE

LIST

3. Press the FOCUS buttons and align the focus of the projected image.

A press of the FOCUS buttons results in focus being taken simultaneously with the adjust-

ment of vertical keystone distortion. See page E-9.

90

Top view Side view

Screen surface

Parallel

Align the projector

center with the

screen center

Bottom of projector

Cabinet controls Remote control

E-8

5. Adjust the height of the screen and the height of the

stand and align the lower edge of the projected image

with the lower edge of the screen.

4. Move the projector away from or closer to the

screen and position it so that the left and right

sides of the projected image are aligned with the

width of the screen.

6. Press the FOCUS buttons and align the focus of the projected

image again.

• Repeat step 4 to 6 if the display image is not aligned with

the screen.

E-9

NOTE:

• In terms of the optical characteristics of this projector, in addition to keystone distortion

(page E-11), there may be occurrences of slight pincushion type or barrel type distortion.

To adjust the projected image with the screen, first perform Steps 1 to 6 pages E-7 to E-9

(Adjustment of the projection distance → Height adjustment of the projected image → Fo-

cus adjustment), then align the 4 corners of the projected image with the 4 corners of the

screen. Following this, if the pincushion type or the barrel type distortion is conspicuous,

please perform "7. Adjusting Pincushion or Barrel Distortion (Pincushion)" on the next page.

• If the keystone distortion is not improved after pressing the FOCUS buttons and adjusting

the focus, or the aspect ratio does not agree, check the screen or projector are not on a tilt.

[Symptom1]

In the case of keystone distortion (as illustrated), either the

screen is directed slightly upward or the projector is directed

slightly upward.

[Action]

Tilt the top end of the screen to the front or rotate the front

feet of the projector to correct keystone distortion.

Up

Down

Continued on the next page.

E-10

[Symptom2]

In the case of keystone distortion (as illustrated), either the

screen is directed slightly downward or the projector is di-

rected slightly downward.

[Action]

Tilt the bottom end of the screen to the front or rotate the

rear feet (screen side) of the projector to correct keystone

distortion.

PC CARD

AUDIO IN

L

/MONO

R

VIDEO IN

S-VIDEO IN

DVI-I IN

RGB IN

RGB OUT

DVI-I RGB

AUDIO IN

USB

AUDIO OUT

PCCONTROL

REMOTE

IN

POWER

ENTEER

MENU

SOURCE

FOCUS

PC CARD

CANCEL

STATUS

LAMP

ON/

STAND BY

AUTO

ADJUST

3D

REFORM

SELECT

Up Down

[Symptom 3]

As illustrated in the diagram to the bottom right, when the

left edge of the image is widened vertically, either the pro-

jector is not placed straight in front of the screen or the pro-

jector is directed slightly to the left.

Conversely, when the right edge of the image is widened

vertically, either the projector is not placed straight in front

of the screen or the projector is directed slightly to the right.

[Action]

Place the projector straight in front of the screen.

Make sure that the screen and the projector are parallel to

each other.

a

bb bb

E-11

7. Adjusting Pincushion or Barrel Distortion (Pincushion)

a: 1% or less of the screen height

(2% or less as TV distortion)

b: 1% or less of the screen width

(2% or less as TV distortion)

1 Press the 3D REFORM button of the projector or

the remote control.

The [Pincushion] screen will appear.

If pincushion or barrel distortion become conspicuous, adjust with [Pincushion].

Reference

• Pincushion or barrel distortion in this projector

The amount of pincushion and barrel distortion in this projector is 2% or less (TV distortion) in

each of the horizontal and vertical directions (for screen sizes of 40 inches to 100 inches).

As an example, the amount of distortion with a screen size of 60 inches (121.9 cm/48.0” W x

91.4 cm/36.0” H) is within approximately 12 mm/0.47” in the horizontal direction and within

approximately 9 mm/0.35” in the vertical direction. When this projector is used with a 60-inch

screen size, the amount of pincushion and barrel distortion become a minimum.

When the amount of pincushion or barrel distortion exceed 2% (TV distortion), please check

whether the projector and screen setup conditions are suitable.

Screen (solid line)

Projected area (dotted line)

• Press the SELECT 왖왔 button and align the cursor

with [Left/Right], then press the SELECT 왗왘 but-

ton to allow adjustment of the left and right protru-

sions and indentations of the projected image.

E-12

Screen (solid line)

Projected area (dotted line)

• Press the SELECT 왖왔 button and align the cur-

sor with [Top], then press the SELECT 왗왘 button

to allow adjustment of the protrusions and inden-

tations of the upper edge of the projected image.

Screen (solid line)

Projected area (dotted line)

• Press the SELECT 왖왔 button and align the cur-

sor with [Bottom], then press the SELECT 왗왘 but-

ton to allow adjustment of the protrusions and in-

dentations of the lower edge of the projected im-

age.

2. Press the ENTER button when [Pincushion] is completed.

Return to the menu.

3. Press the CANCEL button a few times to make the menu disappear.

NOTE:

• In the [Pincushion] screen, when the [Top] adjustment value is "0", adjustment of [Bottom] will

not be possible*.

Also note that when the adjustment value of the [Top] is a small value (on the order of +5), there

will be almost no change of the image even when the [Bottom] is adjusted.

• In the [Pincushion] screen, when the [Bottom] adjustment value is less than "0", a small portion

can be lost at the bottom area of the image. To display the lost portion, use the [Digital Zoom]

function to reduce the size of the projected image*.

• When [Cornerstone] or [Keystone] has already been adjusted, selection of [Pincushion] will not

be possible. To display [Pincushion], return the adjustment values of [Cornerstone] or [Key-

stone] to the factory shipping conditions.

* Each note for [Top] and [Bottom] is reversed when the [Ceiling Rear] or [Ceiling Front] is se-

lected in [Orientation] .

Reference

The [Pincushion] screen can also be displayed from the advanced menu by going to [Projector

Options] → [3D Reform].

E-13

Indicator Condition

Projector Condition Note

Indicator Condition

Projector Condition

Note

This section helps you resolve problems you may encounter while setting up or using the projector.

Power Indicator

Indicator Condition

Projector Condition

Note

Off

0.5 sec ON,

0.5 sec OFF

2.5 sec ON,

0.5 sec OFF

0.5 sec ON,

0.5 sec OFF

The main power is off

The projector is getting ready to

turn on.

The projector is in Sleep mode.

The projector is cooling down.

The projector is turned on.

The projector is in Idle or Standby.

Green

Orange

–

Wait for a moment.

–

Wait for a moment.

–

Off Normal

Lamp cover error

Mirror cover error

Temperature error

Temperature error due to dust

Power error

Fan error

Lamp error

Re-firing the lamp

Control key locked

A hand or an object blocks the light

path.

Idle condition

–

Replace the lamp cover correctly.

Make sure the mirror cover is

open. Projector cannot be turned

on with the mirror cover closed.

The projector is overheated. Move

the projector to a cooler location.

Remove dust in the light path.

Power unit will not work correctly.

Fans will not work correctly.

Lamp fails to light. Wait a full

minute and then turn on again.

The projector is re-firing.

You have pressed control panel key

when Control Key Lock is enabled.

Remove it from the light path.

–

Status Indicator

Blinking light

Steady light

Green blinking

Orange blinking

Blinking light

Steady light

Red blinking

Green blinking

Orange

Red

Green

1 cycle (0.5 sec ON,

2.5 sec OFF)

2 cycle (0.5 sec ON,

0.5 sec OFF)

3 cycle (0.5 sec ON,

0.5 sec OFF)

4 cycle (0.5 sec ON,

0.5 sec OFF)

6 cycle (0.5 sec ON,

0.5 sec OFF)

Off Normal

Lamp has reached its end of life. Lamp replacement mes-

sage will be displayed.

Lamp has been used beyond its limit. The projector will not

turn on until the lamp is replaced.

Lamp mode is set to Eco mode

Red

Green

–

Replace the lamp.

–

Lamp Indicator

Blinking light

Steady light

8. Troubleshooting

• Check that the power cable is plugged in and that the power button on the projector cabinet

or the remote control is on. See pages 2-7 and 3-1.

• Ensure that the lamp cover is installed correctly. See page 7-1.

• Check to see if the projector has overheated or the lamp usage exceeds 2100 hours (up to

3100 hours : Eco mode). If there is insufficient ventilation around the projector or if the

room where you’re presenting is particularly warm, move the projector to a cooler location.

• Check to see if the Control Panel Key Lock function is enabled. If this function is enabled,

cancel it by pressing and holding the CANCEL button on the cabinet for a minimum of 10

seconds or using the menu. See page 6-17.

• Use the menus or SOURCE button to select your source (RGB, DVI (DIGITAL), DVI (ANA-

LOG), Video, S-Video, Viewer or LAN). See page 3-2 or 6-6.

• Ensure your cables are connected properly.

• Use menus to adjust the brightness and contrast. See page 6-7.

• Open the mirror cover. See page 1-3.

• Reset the settings or adjustments to factory preset levels using the Factory Default in the

Adjustment Menu. See page 6-25.

•When using with a notebook PC, be sure to connect between the projector and the notebook

PC before turning on the power to the notebook PC. In most cases signal cannot be output

from RGB output unless the notebook PC is turned on after connecting with the projector.

* If the screen goes blank while using your notebook PC, it may be the result of the computer's

screen-saver or power management software.

* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then

press the POWER button again to resume.

To project a DVI digital signal, be sure to connect the PC and the projector using the DVI-D

signal cable (supplied) before turning on your PC or projector. Turn on the projector first

and select DVI (DIGITAL) from the source menu before turning on your PC.

Failure to do so may not activate the digital output of the graphics card resulting in no

picture being displayed. Should this happen, restart your PC.

Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable

has been disconnected and then reconnected, an image may not be correctly displayed.

Should this happen, restart your PC.

• Reposition the projector to improve its angle to the screen. See page 3-2.

• Use the 3DReform function to correct the trapezoid distortion. See page 6-10 to 6-13.

• Adjust the focus. See page 3-3.

• Reposition the projector to improve its angle to the screen. See page 3-2.

• Ensure that the distance between the projector and screen is within the adjustment range of

the mirror. See page 2-2.

• Condensation may form on the mirror if the projector is cold, brought into a warm place and

is then turned on. Should this happen, let the projector stand until there is no condensation

on the mirror.

• Use the menus or SOURCE button on the remote control or the cabinet to select the source

you want to input.

• Install new batteries. See page 1-8.

• Make sure there are no obstacles between you and the projector.

• Stand within 22 feet (7 m) of the projector. See page 1-8.

• Make sure that you are in the Projector mode and the PJ button lights in red. If not, press the

PJ button. See page 4-1.

• See the Status Indicator on page 8-1.

• If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the

Image Options. See pages 6-8 and 6-16.

• Make sure that your USB mouse is properly connected to the projector.

The projector may not support some brands of a USB mouse.

Common Problems & Solutions

Does not turn on

No picture

Image isn’t square to the screen

Picture is blurred

Image is scrolling vertically, horizontally or

both

Remote control does not work

Indicator is lit or blinking

Cross color in RGB mode

USB mouse does not work

Problem

Check These Items

The numbers in the table refer to pages in the user's manual.

For more information contact your dealer.

E-14

AUFSTELLUNGSANLEITUNG WT600

Inhalt

Für den WT600 geeignete Bildschirme .............................. G-2

Für den WT600 geeignete Ständer .................................... G-2

Umgebungsbedingung ....................................................... G-3

Teilebezeichnungen des Projektors ................................... G-3

1. Aufstellung von Bildschirm und Projektor ....................... G-4

2. Anschlüsse ..................................................................... G-5

3. Öffnen des Spiegelobjektivs ........................................... G-5

4. Einschalten des Gerätes ................................................ G-6

5. Signalauswahl ................................................................ G-6

6. Einstellung von Position und Größe des projizierten Bildes

(Fokussierung) ................................................................G-7

7. Korrektur von Nadelkissen- und Konvexverzerrung

(Nadelkissen) ................................................................ G-11

8. Fehlersuche.................................................................. G-13

P

O

W

E

R

E

N

T

E

R

M

E

N

U

S

O

U

R

C

E

F

O

C

U

S

P

C

A

R

D

C

A

N

C

E

L

S

T

A

TU

S

L

A

M

P

O

N

/

S

T

A

N

D

B

Y

A

U

TO

A

D

JU

S

T

3

D

R

E

F

O

R

M

S

E

LE

C

T

PC C

AR

D

A

U

D

IO

IN

R

L

/M

O

N

O

VIDEO IN

S-V

IDEO

IN

DV

I-I IN

R

GB

IN RGB OUT

DV

I-I

RGB

AUDIO IN

USB

AUD

IO OUT

P

C

CON

TROL

REM

OTE

IN

HINWEIS

(1) Der Inhalt dieser Anleitung darf ohne Genehmigung weder als Ganzes noch in

Auszügen kopiert werden.

(2) Änderungen am Inhalt dieser Anleitung ohne Ankündigung bleiben vorbehalten.

(3) Diese Anleitung wurde mit großer Gründlichkeit zusammengestellt. Bei Zweifeln,

Fehlern oder Auslassungen wenden Sie sich bitte an uns.

(4) Ungeachtet des Abschnittes (3) übernimmt dieses Unternehmen keinerlei Haftung

für Verluste oder Profitausfall, die als Folge des Einsatzes dieses Gerätes hergeleitet

werden könnten.

(5) Anleitungen mit falscher Seitenfolge oder fehlenden Seiten werden ersetzt.

(6) Bei geringfügigen Diskrepanzen zwischen Bedienungsanleitung und dieser Anlei-

tung hat diese Anleitung Priorität.

Zweck dieser Anleitung

Diese Anleitung beschreibt die Einstellung der Größe des vom WT600

projizierten Bildes. Darüber hinaus sind Beschreibungen der für den

WT600 geeigneten Bildschirme und Ständer enthalten.

Die Einzelheiten zur Bedienung finden Sie in der Bedienungsanleitung

des WT600 (nachfolgend “das Gerät” oder “der Projektor” genannt).

G-1

WARNUNG

•

Stellen Sie den Projektor, den Bildschirm und den Ständer keinesfalls an einem

schrägen oder instabilen Ort auf. Der Ständer könnte um- und der Projektor herabfallen

und Verletzungen verursachen.

•

Stelen Sie bei der Befestigung des Projektors auf dem Ständer zuerst die obere

Montageplatte waagerecht ein. Bei schief ausgerichteter Montageplatte kann der

Projektor herabfallen und Verletzungen verursachen.

•

Verwenden Sie einen Ständer, der das volle Gewicht des Projektors tragen kann (bei

diesem Gerät sind das ca. 5,9 kg). Bei einer Missachtung dieses Hinweises könnte

der Projektor herabfallen und Verletzungen verursachen.

La pagina sta caricando ...

NEC WT600 Manuale del proprietario

NEC WT600 Manuale del proprietario

in altre lingue

Documenti correlati

Altri documenti