Yamaha MCR-B020 Orange Manuale utente

Categoria
Lettore CD
Tipo
Manuale utente
Integrated Amplifier
Amplificateur Intégré
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
G
Printed in China MCR-B020/G
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
G
Micro Component System
Micro-Chaîne
English Français Deutsch Svenska Italiano Español Nederlands Русский
i En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place -
away from direct sunlight, heat sources, vibration, dust,
moisture and cold. For proper ventilation, allow the
following minimum clearances.
Top: 15 cm (6 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an
environment with high humidity (i.e. a room with a
humidifier) to prevent condensation inside this unit, which
may cause an electrical shock, fire, damage to this unit,
and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid
dripping or splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage other
than specified.
13 To prevent damage by lightning, keep the power cable
disconnected from a wall outlet or this unit during a
lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the
wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press to set the unit to off,
and disconnect the AC power plug from the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power
cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may become
warm. Turn off, then leave this unit alone for cooling.
20 Install this unit near the wall outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like. When you dispose of
batteries, follow your regional regulations.
Keep the batteries in a location out of reach of children.
Batteries can be dangerous if a child were to put in his or
her mouth.
If the batteries grow old, the effective operation range of
the remote control decreases considerably. If this happens,
replace the batteries with new one as soon as possible.
Exhausted batteries may leak. If the batteries have leaked,
dispose of them immediately. Avoid touching the leaked
material or letting it come into contact with clothing, etc.
Clean the battery compartment thoroughly before
installing new batteries.
If you plan not to use the unit for a long period of time,
remove the batteries from the unit. Otherwise, the batteries
will wear out, possibly resulting in a leakage of battery
liquid that may damage the unit.
Do not throw away batteries with general house waste.
Dispose of them correctly in accordance with your local
regulations.
22 Excessive sound pressure from earphones and headphones
can cause hearing loss.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off by . In this state, this unit is designed
to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
There is a chance that placing this unit too close to a CRT-
based (Braun tube) TV set might impair picture color.
Should this happen, move this unit away from the TV set.
1 En
English
NAMES OF PARTS AND THEIR FUNCTIONS ........2
Top panel/Front panel....................................................2
Front panel display.........................................................2
Remote control...............................................................3
CONNECTIONS ........................................................4
Connecting the speakers and antenna ..........................4
Connecting the power cable...........................................5
Other connections..........................................................5
About the standby state .................................................5
How to use the remote control.......................................5
ADJUSTING THE CLOCK (OPTION MENU) ...........6
LISTENING TO CD AND USB DEVICES .................7
Listening to a CD............................................................7
Listening to a USB device..............................................8
Using repeat/shuffle playback (remote control only)......8
LISTENING TO MUSIC FROM YOUR Bluetooth
DEVICE......................................................................9
Playing back from your Bluetooth device.......................9
Connecting an already-paired device via Bluetooth.....10
Disconnecting a Bluetooth connection.........................10
LISTENING TO FM STATIONS ..............................11
Selecting an FM station................................................11
Presetting FM stations (remote control only) ...............12
Selecting preset FM stations........................................13
LISTENING TO EXTERNAL SOURCES ................13
USEFUL FUNCTIONS ............................................14
Using the Option menu ................................................14
Using the sleep timer ...................................................15
Using the alarm function ..............................................15
Setting the alarm ..........................................................16
Operations while the alarm sound is playing................17
TROUBLESHOOTING ............................................18
NOTES ON DISCS AND USB DEVICES................21
SPECIFICATIONS...................................................22
CONTENTS
Play back music from external devices such as your audio/data CDs, USB devices, or external devices via the AUX jack,
and listen to the radio.
•By the Bluetooth technology, you can enjoy clear sound without wire connections.
Use your favorite music as an alarm. When the set time arrives, the music you select is played at the volume that you
specify, giving you the ideal start to your day.
You can easily store and recall of your favorite radio stations, up to 30 FM stations.
Bass, middle, and treble can be adjusted to your taste.
About this manual
If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will
focus on operation using the remote control.
indicates precautions for use of the unit and its feature limitations.
indicates supplementary explanations for better use.
Features
Supplied accessories
FM antenna
(use a CR2025 type
Lithium battery)
Remote control Speaker cable
(1.5 m (4.9') x 2)
Power cable
Keep the USB cap out of
reach of children so as to
ensure that it is not
mistakenly swallowed.
USB cap
2 En
1 (Power)
Press to turn the unit on/off (standby).
There are two types of the standby state ( P. 5).
2 SOURCE
Switch the audio source to be played.
Pressing this repeatedly will change the selection in the
following order.
CD USB
FM BT AUX
3 Audio control buttons
Use these to operate the CD/USB device.
4 (Eject button)
Eject the CD (cannot be operated while the option menu
( P. 14) is displayed).
5 USB port
Connect your USB device (
P. 5, 8).
When the USB device is not in use, put the USB cap in
place to protect the connector.
6 PRESET /
Use these buttons to select a radio station that you’ve
stored ( P. 12, 13).
7 (Headphone jack)
Connect headphones.
8 Front panel display
The clock and other information is displayed.
9 VOLUME knob
Adjust the volume.
0 Disc tray
Set a disc. ( P. 7).
1 Alarm time
Indicates the alarm time ( P. 16).
2 Repeat/shuffle indicator
Displays the playback mode ( P. 8).
3 Multi-function indicator
Displays various information, including the clock time,
information about the currently-playing track, and the
frequency of the radio station.
4 Remote control signal receiver
Make sure that this sensor is not obstructed ( P. 5).
5 Alarm indicator
Turns on if the alarm has been set ( P. 16).
6 Sleep indicator
Turns on if the sleep timer has been set ( P. 15).
NAMES OF PARTS AND THEIR FUNCTIONS
Top panel/Front panel
: Play/Pause
: Stop
/ : Skip, Search backward/forward (press and hold
down)
Front panel display
3 En
NAMES OF PARTS AND THEIR FUNCTIONS
English
Replacing the battery in the remote control
While pushing the release tab in direction , slide out the
battery holder in direction .
1 Remote control signal transmitter
2 (Power)
Press to turn the unit on/off (standby).
There are two types of the standby state ( P. 5).
3 Source buttons
Switch the audio source to be played. If you press one of
these while the unit is in standby (except ECO standby),
the unit will automatically turn on.
4 OPTION
Display the option menu ( P. 14).
5 Operation buttons
FOLDER /: Switch the playback folder and select
items or edit numerical values when
playing music on data CDs or USB
devices.
ENTER: Confirm a selected item or value.
* Use these to operate the CD/USB device.
6 TUNING /
Tune the radio ( P. 11, 12).
7 PRESET /
Select a radio station that you stored ( P. 12, 13).
8 (Repeat)/ (Shuffle)
Play music on a CD or USB device in repeat/shuffle
mode ( P. 8).
9 ALARM
Switch the alarm on/off ( P. 17).
0 SNOOZE/SLEEP
Set the sleep timer or switch the alarm to snooze mode
( P. 15, 17).
A DISPLAY
Switch the information shown in the front panel display
( P. 7, 8, 11).
B MUTE
Mute or unmute the sound.
C VOLUME + / –
Adjust the volume.
D MEMORY
Store a radio station ( P. 12).
Remote control
CR2025 type
Lithium battery
: Stop*
: Play/Pause*
/ : Skip, Search backward/forward (press and hold
down)*
4 En
Connect the speakers and antenna.
Do not connect this unit’s power cable until you’ve finished connecting all cables.
If the radio reception is poor, try changing the height or direction or placement of the antenna to find a location that has better
reception.
If you use a commercially available outdoor antenna instead of the supplied antenna, reception may be better.
CONNECTIONS
Connecting the speakers and antenna
Speakers
You must peel off the insulation (covering) from the tip of the speaker cable to expose the conductor.
Check the connections; make sure that left and right (L, R) and polarity (red: +, black: –) are connected correctly. If connections are
incorrect, the sound will be unnatural and the low frequencies may be insufficient. There might not be any sound at all if connections are
incorrect.
Take care that the conductors of the speaker cable do not touch each other, and that the conductors do not touch any other metal part.
Such conditions can damage this unit or the speakers.
Use only the supplied speakers. Using other speakers may result in unnatural sound.
If you’re using this unit nearby a CRT display and you notice distorted color or noise in the display, move the speakers farther away from
the display.
FM antenna
Fix the end of the FM antenna to a wall.
Connect the FM
antenna plug to the
rear panel FM
antenna terminal with
the side illustrated on
the left.
Twist the bare wires
tightly so the individual
strands are not splayed.
Reset button
( P. 18)
5 En
CONNECTIONS
English
USB device
External devices
This unit has the following two types of standby state. Select the mode in POWER SAVING settings menu ( P. 14).
* Default setting
Connecting the power cable
When you’ve completed all connections, connect the
supplied power cable to AC IN, and then connect the plug of
the cable to an AC outlet.
Other connections
Rear panel
To AC outlet
Connect your USB device to the USB port on the top panel.
For details on playable files, refer to “NOTES ON DISCS
AND USB DEVICES” ( P. 21 ).
The USB device is automatically charged when this unit is
connected to the AC outlet.
Stop playback before disconnecting the USB device.
Charging may not be possible depending on the USB device.
Using a commercially available 3.5 mm stereo mini-plug
cable, connect your external device to the AUX jack on the
rear panel of this unit.
About the standby state
Mode
Setting menu
(POWER
SAVING)
Clock display
Bluetoot h
connection
Charging of USB
devices
Alarm setting
ECO standby
*
(power saving mode)
ECO No clock display Disable Enable Disable
Standby NORMAL Show Enable Enable Enable
How to use the remote control
Rear panel
Within 6 m (20')
Battery insulation sheet: Remove before using.
6 En
You’ll use the option menu ( P. 14 ) to set this unit’s date and time.
ADJUSTING THE CLOCK (OPTION MENU)
1 Press to turn the unit on.
2 Press OPTION.
The option menu will appear.
3 Press / to select “CLOCK SET,” and then
press ENTER.
The display will indicate “CLOCK YEAR,” and the
numerical value to be set will blink.
4 Set the date and time.
Press / to edit each numerical value, and then press
ENTER to confirm the setting.
Set the items in the order of year month day
hour minute.
When clock setting has finished, the display will indicate
“Completed!”
The clock will be set to 0 second the moment you
complete the clock settings.
While making these settings, you can press DISPLAY to
select the time format (12-hour / 24-hour).
If you decide to cancel without changing the setting, press
OPTION before confirming the change.
The time settings will be reset if the unit remains unpowered for
about one hour.
26
Apr
Jan Feb Mar Apr May Jun
January February March April May June
Jul Aug Sep Oct Nov Dec
July August September October November December
2
43
15:30
CD
Display (24-hour) when the unit is on
Display (24-hour) when the unit is off (standby)
*
Clock display
1
* In ECO standby, the clock display will disappear.
7 En
English
Skipping folders (remote control only)
Display information (remote control only)
LISTENING TO CD AND USB DEVICES
The unit will operate as follows when playing back tracks/files on CD/USB devices.
If the CD/USB device being played is stopped, the track that you listened will start playback from the beginning of the
track the next time you play.
If you press while playback is stopped, tracks will play as follows the next time playback begins:
Audio CD: Play from the first track of the CD.
Data CD*/USB device:
Play from the first track of the folder contains the track you listened to last time.
This unit automatically turns off if no operation has been performed for 20 minutes after CD/USB device playback is
stopped.
* “Data CD” is a CD that contains MP3/WMA files.
For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” ( P. 21).
Listening to a CD
1 Press the CD source button to switch the
audio source to CD.
If a CD is already set, playback will start.
2 Press the (eject button) to open the disc tray.
3 Set a CD into the disc tray.
Set the CD with the label side facing upward.
4 Press the (eject button) to close the disc
tray.
5 Press the to start playback.
Playback can be controlled with either the remote
control, or the top panel on this unit ( P. 2, 3).
Folders and files on a data CD are played in alphabetical order.
While a data CD is playing, you can use the remote control’s
FOLDER / buttons to select the folder.
The folder number (only for a data CD) or the song/file
number is shown for several seconds when starting playback
or skipping tracks.
If you press
DISPLAY
on the remote control while a song is
playing or paused, the information shown on the front panel
display will be switched in the following order.
- Elapsed song playback time
- Remaining song playback time (only for an audio CD)
- Song name*
- Album name*
- Artist name*
- File name (only for a data CD)
- Folder name (only for a data CD)
* Shown only if this data is included in the song.
3
2 4
5
1
LISTENING TO CD AND USB DEVICES
8 En
Skipping folders (remote control only)
Display information (remote control only)
The playback status is shown by the repeat/shuffle indicator in the front panel display.
Repeat playback Shuffle playback
Listening to a USB device
1 Press the USB source button to switch the
audio source to USB.
If a USB device is already connected, playback will start.
2 Connect a USB device to the USB port.
Playback starts automatically.
Playback can be controlled with either the remote control,
or the top panel on this unit (
P. 2,
3
).
Folders and files will play in the order in which they were written.
Stop playback before disconnecting the USB device.
While a USB device is playing, you can use the remote
control’s FOLDER / buttons to select the folder.
The folder/file number is shown for several seconds when
starting playback or skipping tracks.
If you press
DISPLAY
on the remote control while a song is
playing or paused, the information shown on the front panel
display will be switched in the following order.
- Elapsed song playback time
- Song name*
-Album name*
- Artist name*
-File name
- Folder name
* Shown only if this data is included in the song.
Using repeat/shuffle playback (remote control only)
1
2
Press (repeat) repeatedly
to select one of the following
playback modes.
No display: Repeat mode off
: 1 track
: All tracks within the folder (data CD/USB device
only)
: All tracks
Press (shuffle) repeatedly
to select one of the following
playback modes.
No display: Shuffle mode off
: All tracks within the folder (data CD/USB device
only)
: All tracks
9 En
English
This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device (mobile
phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.
You’ll need to perform the pairing operation the first time you use your Bluetooth device with this unit, or if the pairing
settings have been deleted. Pairing is an operation that registers the Bluetooth device with this unit. Once pairing has been
completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected ( P. 10). If pairing is
not successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” ( P. 20).
Yamaha does not guarantee all connections between this unit and Bluetooth device.
This unit can be paired with up to 8 Bluetooth devices. When pairing with the 9th device has succeeded, pairing data for the device with the
oldest connection date will be deleted.
While connecting to the Bluetooth device and perform the pairing with another device, the current Bluetooth connection will be canceled.
LISTENING TO MUSIC FROM YOUR
Bluetooth
DEVICE
Playing back from your Bluetooth device
1 Press the BLUETOOTH source button for
more than 2 seconds to enter pairing mode.
Pairing mode lasts for 5 minutes.
In pairing mode, the front panel display of this unit will
indicate “BT Pairing...”.
You can also enter pairing mode by holding down SOURCE on
this unit.
2 Perform Bluetooth pairing on the Bluetooth
device.
For details refer to the owner’s manual of the Bluetooth
device.
3 From the Bluetooth connection list of the
Bluetooth device, choose this unit (MCR-B020
Ya m a h a ).
When pairing has been completed, the front panel display
of this unit will indicate “BT Pairing OK”.
If you are asked to enter a password, enter the numerals “0000”.
4 Connect this unit and the Bluetooth device via
Bluetooth.
5 Play back music from the Bluetooth device.
Take care that the volume setting of this unit is not too high. We
recommend that you adjust the volume on the Bluetooth device.
If you connect via Bluetooth from the Bluetooth device while this
unit is in standby (except ECO standby), this unit will
automatically turn on.
If you disconnect the Bluetooth connection from the Bluetooth
device while the audio source is set to Bluetooth, this unit will
automatically turn off.
If Bluetooth is selected as the audio source, this unit will
automatically turn off when 20 minutes have elapsed without any
Bluetooth connection nor any operation performed.
1
15:30
BT
Pairing OK
3
LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE
10 En
Once pairing has been completed, connecting a Bluetooth will be easy the next time.
Connecting from this unit
Connecting from the Bluetooth device
If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be
disconnected.
Switch the audio source other than Bluetooth.
Turn the unit off.
Turn off the Bluetooth setting of the Bluetooth device.
Connecting an already-paired device via Bluetooth
Press the BLUETOOTH source button to switch
the audio source to Bluetooth.
The Bluetooth indicator will blink in the front panel display;
this unit will search for the Bluetooth device that was most
recently connected via Bluetooth, and will then establish a
connection (You must first turn on the Bluetooth setting of
the Bluetooth device).
When the Bluetooth connection has been established, the
Bluetooth indicator will light, and the name of the Bluetooth
device will be displayed.
1 In the Bluetooth settings of the Bluetooth device, turn Bluetooth on.
2
From the
Bluetooth
connection list of the
Bluetooth
device, choose this unit (MCR-B020 Yamaha).
The Bluetooth connection will be established, and the front panel display of this unit will indicate the name of the
Bluetooth device.
Bluetooth
connections cannot be established from the
Bluetooth
device when this unit is in ECO standby (
P. 5).
Disconnecting a Bluetooth connection
15:30
15:30
BT
_____
11 En
English
To listen to the FM station, connect the antenna as described in “Connecting the speakers and antenna” ( P. 4).
Display information (remote control only)
If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the
following order.
LISTENING TO FM STATIONS
Selecting an FM station
1 Press the RADIO source button to switch the
audio source to FM.
2 Tune FM stations
Automatic tuning: Press and hold TUNING / .
Manual tuning: Press TUNING / repeatedly.
If you tune to a station manually while receiving FM, the sound
will be monaural.
Preset number and frequency Reception status*
* Example of reception status indication.
TUNED/STEREO: A strong FM stereo broadcast is
being received.
TUNED/MONO: A monaural FM broadcast is being
received (even if the FM broadcast is
stereo, reception will be monaural if
the signal is weak).
Not TUNED: No broadcast is being received.
Displaying Radio Data System information
If you press DISPLAY on the remote control while Radio
Data System information is being received, the information
shown on the front panel display will be switched in the
following order.
- PS (Program Service)
- PTY (Program Type)
- RT (Radio Text)
- CT (Clock Time)
- Reception status
- Preset number and frequency
If the signal transmission of the Radio Data System station is too
weak, this unit may not be able to receive Radio Data System
information completely. In particular, RT (Radio Text) information
uses a lot of bandwidth, so it may be less available compared to
other types of information.
1
2
LISTENING TO FM STATIONS
12 En
Use the preset function to store your favorite 30 stations.
First, press the RADIO source button to switch the audio source to FM.
Auto preset
This method tunes automatically, and automatically presets only the stations that have good reception.
Manual preset
Deleting a stored preset (Option menu)
Presetting FM stations (remote control only)
1 Press and hold down MEMORY.
AUTO PRESET will appear and Press MEMORY
will blink.
2 Press MEMORY.
Auto preset will begin.
When presetting has finished, the display will indicate
Completed!”.
When you perform auto preset, all stored stations are cleared
and the new stations are stored.
If you want to stop auto preset before it is completed, press .
1 Press TUNING / to tune a station that
you want to preset.
2 Press MEMORY.
The display will indicate “PRESET MEMORY,” and the
preset number will blink.
3 Press PRESET / to select the preset
number that you want to store.
The lowest preset number that has not been stored will be
selected first.
If you want to cancel the presetting, press .
If you select a preset number in which a station has already
been stored, it will be overwritten by the new station.
4 Press MEMORY.
When presetting has finished, the display will indicate
Completed!”.
1 Press OPTION.
The option menu will appear.
2 Press / to select PRESET DELETE, and
then press ENTER.
3 Press / to select the preset number that
you want to delete.
If you want to cancel the deleting, press OPTION.
4 Press ENTER to complete the operation.
When deleting has finished, the display will indicate
Deleted!”.
5 Press OPTION to exit the option menu.
AUTO PRESET
Press MEMORY
1 2
PRESETMEMORY
FM0187.50MHz
3
1
42
1 5
3
4
2
13 En
LISTENING TO FM STATIONS
English
Selecting preset FM stations
1 Press the RADIO source button to switch the
audio source to FM.
2 Press PRESET / to select the FM station
that you want to hear.
You can only select presets that have been stored.
LISTENING TO EXTERNAL SOURCES
1 Using a commercially available 3.5 mm stereo
mini-plug cable, connect your external device
to the AUX jack on the rear panel of this unit.
Turn the unit off before connecting the audio cable.
Turn down the volume of the unit and your external audio
device before connection.
2 Press to turn the unit on.
3 Press the AUX source button to switch the
audio source to AUX.
4 Start playback on the connected external
audio device.
1
2
1
2
Rear panel
3
14 En
When you press
OPTION
, the option menu will appear in the front panel display, allowing you to make the following settings.
(eject button) cannot be operated while the option menu is displayed.
*1
Default setting
Procedure for settings
USEFUL FUNCTIONS
Using the Option menu
Option menu Setting or range See page
PRESET DELETE Deletes a stored preset (shown only if the audio source is FM).
12
DIMMER
Adjusts the brightness of the front panel display (1
*1
: bright, 2: medium, 3: dim).
EQ LOW
Adjusts the tonal character (low frequencies) (–10 - 0
*1
- +10 dB).
EQ MID
Adjusts the tonal character (mid frequencies) (–10 - 0
*1
- +10 dB).
EQ HIGH
Adjusts the tonal character (high frequencies) (–10 - 0
*1
- +10 dB).
BALANCE
Adjusts the volume balance of the left and right speakers (L+10 - CENTER
*1
- R+10).
POWER SAVING
Switches the standby state, NORMAL or ECO
*1
(power saving mode)
5
AUTO PWR
STDBY
You can specify the time after which the unit will turn off automatically.
If no operation occurs for the duration you specify, the unit will turn off automatically
(
TIME 12H
: 12 hours,
TIME 8H
*1
: 8 hours,
TIME 4H
: 4 hours,
TIME 2H
: 2 hours,
OFF
: the unit
will not turn off).
CLOCK SET Sets the date and time.
6
ALARM SET Sets the alarm.
16
BLUETOOTH
Connects this unit and your device via Bluetooth (ON
*1
: enable, OFF: disable).
9
1 Press OPTION.
The option menu will appear.
2 Press / to select the menu item that you
want to set, and then press ENTER.
3 Press / to edit the setting, and then press
ENTER to confirm the setting.
If you want to continue making other settings, repeat the
procedure from step .
4 Press OPTION to exit the option menu.
If you decide to cancel without changing the setting, press
OPTION before confirming the change.
1
3
4
2
2
15 En
USEFUL FUNCTIONS
English
When the specified time has elapsed, the unit will turn off automatically.
The internal sound (melody) and then the selected audio source are played at the time set for the alarm.
If the selected audio source cannot be played back at the time set for the alarm, the internal sound is played back.
Various audio sources
You can choose from audio CD, data CD, USB device, or FM. The following playback methods can also be selected
depending on the audio source:
You can not choose Bluetooth and AUX as the audio source.
Snooze
The snooze function can be enabled to replay the alarm after 5 minutes ( P. 17 ).
Using the sleep timer
Press SNOOZE/SLEEP repeatedly to specify the
time after which the unit will turn off.
You can specify 30, 60, 90, 120 or OFF.
When you select a time, the sleep timer is turned on, and the
sleep indicator ( ) is shown in the front panel display.
If you press SNOOZE/SLEEP while the sleep timer is activated,
the sleep timer setting will be canceled.
Using the alarm function
Source
Playback
method
Function
Audio CD
Selected track The selected track is played repeatedly.
Resume The track you listened to last time is played back.
Data CD/USB device
Folder The selected folder is played repeatedly.
Resume The track you listened to last time is played back.
FM
Preset station The selected preset station is played.
Resume The FM station you listened to last time is played back.
USEFUL FUNCTIONS
16 En
Setting the alarm time and alarm source (Option menu)
The alarm will not function when the unit is in ECO standby. To use the alarm function, set the Option menu item POWER SAVING to
NORMAL ( P. 14).
Setting the alarm
1 Press OPTION.
The option menu will appear.
2 Press / to select “ALARM SET”, and then press ENTER.
The alarm indicator ( ) and numerical value you’re setting will blink.
3 Set the alarm.
Set items 1-3 described below.
Press / to select a numerical value, and press ENTER to confirm it.
4 Complete the settings.
When you set the VOLUME for item 3, the display will indicate
“Completed!” and your settings will be confirmed.
The alarm will be turned on and the alarm indicator ( ) will light.
If you press OPTION or turn the unit off while making alarm settings, the settings will
be cancelled.
4
9:12

Completed!
Alarm time
Alarm indicator
3
1
2
*1
If you choose RESUME when specifying the track/folder/preset number, the last-
played track/folder/station will be played (resume playback)
Items Setting or range
1
ALARM TIME
Make settings in the order of hours minutes.
2
ALARM SOURCE
CD: Play back music from a CD.
Specify the track number (data CD: folder
number) (RESUME
*1
, 1-99).
USB: Play back music from a USB device.
Specify the folder number (RESUME
*1
, 1-999).
FM: Play a FM station.
Specify the preset number (RESUME
*1
, 1-30).
3
ALARM VOLUME
Specifies the volume (5-60) of the alarm.
17 En
USEFUL FUNCTIONS
English
Switching the alarm on/off
When the set time arrives, the set alarm sound will play. During playback, the following operations are available.
To pause the alarm (Snooze)
To turn the alarm off
Press ALARM to turn the alarm on/off.
When the alarm is on, the alarm indicator ( ) will light,
and the alarm time will be shown.
If you press ALARM again, the alarm indicator ( )
and the alarm will turn off.
If the Option menu item POWER SAVING is set to ECO,
the alarm will not function ( P. 14).
Operations while the alarm sound is playing
Press SNOOZE/SLEEP.
Snooze will stop the alarm and play it again 5 minutes later.
If you press SNOOZE/SLEEP while the alarm is activated, the
alarm sound will stop for about 5 minutes.
Buttons on the unit other than the will also function as the
snooze button.
Press ALARM or .
You can also stop the alarm by holding down SNOOZE/SLEEP.
If you don’t stop the alarm, it will stop automatically after 60
minutes and the unit will turn off.
The alarm setting will be saved even if the alarm is turned off.
If the alarm is turned on again by pressing ALARM, the alarm
will sound with the previous alarm settings.
18 En
If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested
solutions or if the problem is not listed below, turn off and unplug the unit, and consult the nearest authorized Yamaha dealer
or service center.
TROUBLESHOOTING
General
Problem Cause Solution
The speakers make no sound. The volume might be set to the minimum level,
or muted.
Adjust the volume level.
The source may be incorrect. Select the correct source.
The speakers may not be connected securely. Check the connections ( P. 4).
Headphones are connected. Remove the headphones.
The volume of a connected external device is not
loud enough.
Raise the volume of the external device.
Sound suddenly turns off. The sleep timer may be set ( P. 15). Turn the unit on and play the source again.
The auto power standby function may have
operated.
When the time specified for AUTO PWR STDBY in the
option menu has elapsed ( P. 14) or when 20 minutes
have elapsed without any operation being performed after
stopping USB device or CD playback, the unit will turn off
automatically.
Sound is cracked/distorted or
there is abnormal noise.
Input source volume is excessive, or volume of
this unit is excessive (especially Bass).
Adjust volume with VOLUME, or use the option menu
( P. 14) to adjust the bass range. If an external device is
playing back, lower the volume of the external device.
The unit does not operate
properly.
The unit may have received a strong electrical
shock such as lightning or excessive static
electricity, or power supply may have dropped.
Press the reset button on the rear panel of the unit ( P. 4)
using a fine-tipped stick and restart the unit.
The unit turns on but
immediately shuts off.
A digital or high-frequency
equipment produces noises.
The unit may be placed too close to the digital or
high-frequency equipment.
Place the unit farther away from the equipment.
The clock setting has been
cleared.
The unit remained unpowered for about one hour. Plug the power cable into the wall outlet firmly, and set the
clock again ( P. 6).
Alarm does not sound. The unit is set to ECO standby. In the option menu, set POWER SAVING to NORMAL
( P. 14).
The front panel display indicates
“ALARM not work” and can’t
set the alarm.
The unit turns off unexpectedly. The auto power standby function may have
operated.
When the time specified for AUTO PWR STDBY in the
option menu has elapsed ( P. 14) or when 20 minutes
have elapsed without any operation being performed after
stopping USB device or CD playback, the unit will turn off
automatically.
Remote control
Problem Cause Solution
The remote control does not work
properly.
The remote control may be operated outside its
operation range.
For information on the remote control operation range,
refer to “How to use the remote control” ( P. 5).
The remote control signal receiver on the unit
( P. 2) may be exposed to direct sunlight or
lighting (inverted fluorescent lamps).
Change the lighting or orientation of the unit.
The battery may be worn out. Replace the battery with a new one ( P. 3).
There are obstacles between the remote control
signal receiver on the unit ( P. 2) and the
remote control.
Remove the obstacles.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195

Yamaha MCR-B020 Orange Manuale utente

Categoria
Lettore CD
Tipo
Manuale utente