Sony CMR-PC1 USB Manuale utente

3-065-554-13(1)

 2000 by Sony Corporation

Operating Instructions

Mode d’emploi

Bedienung sanleitung

Guía de instrucciones

Istruzioni per l’uso

CMR-PC1 USB

USB Camera

FR

DE

GB

ES

IT

English

WARNING

To prevent fire or shock

hazard, do not expose the

unit to rain or moisture.

To avoid electrical shock,

do not open the cabinet.

Refer servicing to qualified

personnel only.

• Microsoft, MS, MS-DOS and Windows are trademarks or registered trademarks of

Microsoft Corporation.

• Licensed software from Luxxon Corporation is included in this package.

Luxxon Corporation

2055 Gateway Place, Suite 350

San Jose, CA 95110, USA

• Other system names and product names appearing in this document are generally registered

trademarks or trademarks of their manufacturers, although ™ and ® marks are not shown in

this document.

Before using this camera, please read the Software License Agreement that is printed in these

Operating Instructions.

❑ Copying all or part of the contents of the Operating Instructions or the software

supplied with this camera or renting the software without the permission of the

copyright holder is prohibited by copyright laws.

❑ Sony is not liable for damage or loss resulting from the use of the software supplied

with this camera, or for any claim from a third party.

❑ Sony assumes no responsibility aside from the replacement of the media due to

manufacturing fault.

❑ The software supplied with this camera must not be used with other devices than this

camera.

❑ Be sure to perform a test operation to confirm that images and sound are recorded

correctly.

❑ Sony shall not be liable for the loss of recorded contents resulting from any inability of

this camera or software to record images or sound.

❑ The software specifications are subject to change without notice.

For the Customers in Germany

Directive: EMC Directive 89/336/EEC.92/

31/EEC

This equipment complies with the EMC

regulations when used under the following

circumstances:

• Residential area

• Business district

• Light-industry district

(This equipment complies with the EMC

standard regulations EN55022 Class B.)

3

GB

English

Table of Contents

GB

English

Table of Contents

Introduction..........................................................................4

System Requirements .........................................................4

Checking Kit Contents ........................................................4

Identifying the Parts ............................................................5

Required Settings Before You Can Use Your Camera .....6

Installing the Drivers, “Camera Setting Utility” and

“SONY USB CAMERA Viewer”................................ 6

Using Your Camera ...........................................................12

Connecting to a Notebook Computer .............................. 12

Connecting to a Desktop Computer................................. 13

Detaching the Camera...................................................... 13

Shooting With the Camera............................................... 14

Notes on Use......................................................................15

On placement ................................................................... 15

On operation .................................................................... 15

On transportation ............................................................. 15

On the lens ....................................................................... 15

On discs ........................................................................... 15

Maintenance.......................................................................16

Cleaning the camera ........................................................ 16

Cleaning the lens ............................................................. 16

Cleaning discs.................................................................. 16

Main Specifications ...........................................................17

Troubleshooting ................................................................18

SOFTWARE LICENSE AGREEMENT ...............................21

4

GB

Introduction

With your camera you can shoot both video clips and still pictures.

Recorded moving pictures can be sent as video mail, or still pictures

can be included in reports* on meetings in order to convey the

atmosphere of the meeting, etc.

* Smart Write must be installed.

System Requirements

The following system requirements must be met in order to use this

camera.

❑ CPU: Pentium MMX 200 MHz or faster. (Celeron 533 MHz or

faster is recommended.)

❑ OS: Windows 98, Windows 98 SE, Windows 2000 Professional or

Windows Millennium Edition

❑ RAM: 64 MB or more.

❑ Free hard disk storage space: 210 MB or more.

Checking Kit Contents

When unpacking, check that the following contents are supplied with

your camera.

Should anything be missing, please contact your Sony dealer.

• USB camera (CMR-PC1 USB) with USB interface cable

• Install disc (CD-ROM × 1) with drivers, bundled software, and a

software manual (PDF)

5

GB

• USB camera “Operating Instructions” (this manual)

• Quick Start

• Pouch

• Camera monitor mount

• Microphone

• Warranty card

Identifying the Parts

Front

Focus ring

Lens

Arm plate

Rear

CAPTURE button

6

GB

Required Settings Before You Can Use

Your Camera

Using the supplied install disc, you must first install the necessary

drivers and software on the computer.

Installing the Drivers, “Camera Setting Utility” and

“SONY USB CAMERA Viewer”

This section describes the procedures for installing the drivers required

to connect your camera and the “Camera Setting Utility” software used

for setting your camera and the “SONY USB CAMERA Viewer”

software used for testing any of the camera’s functions.

Your camera is designed specially for use with computers with

preinstalled versions of Windows 98, Windows 98 SE, Windows 2000

Professional or Windows Millennium Edition. It cannot be used with

other computers.

1 Turn on the computer without the camera being connected.

2 Insert the CD-ROM into the CD-ROM drive.

3 Click the [Start] button, and then select [Run] to continue.

4 Type “d:\Drivers\USBCam\setup.exe”, where “d:\” is the drive

letter of your CD-ROM drive; then click [OK] to start the “SONY

USB CAMERA Drivers and Viewer” installation program.

7

GB

Continued

5 When “SONY USB CAMERA Installer Setup Wizard” window

appears, select [Next] to continue.

6 At this point you can select the folder for installation. Enter the

name of the folder in which you want to install the programs, or

click [Browse] to continue (installation in “C:\Program

Files\SONYUSB Camera\” is recommended). Then select [Next]

to continue.

8

GB

7 The installation program asks for confirmation of the installation.

If it is all right to start the installation, select [Next] to continue.

8 Now the “SONY USB CAMERA Drivers and Viewer” program

has been installed. Click [Close] to close and exit the installation

program.

9 Restart the computer.

10

Connect the camera to the computer.

For details, see “Connecting to a Notebook Computer” (page 12),

or “Connecting to a Desktop Computer” (page 13).

9

GB

Continued

If the “Add New Hardware Wizard” dialog box appears

when you connect your camera

If this happens, install drivers as follows:

1 The “Add New Hardware Wizard” searches for new drivers for the

USB Composite Device.

Click [Next].

2 Select “Search for the best drive for your device” and click [Next].

3 Insert the Sony USB Camera CD-ROM in the CD-ROM drive.

4 Select “Specify a location” and type “d:\Win98\Drivers” where

“d:\” is the drive letter for your CD-ROM drive, then click [Next].

Windows starts installing the drivers.

5 “SONY USB CAMERA Video Capture Device” appears in the

“Add New Hardware Wizard” dialog.

Click [Finish].

6 If driver installation was successful, “SONY USB CAMERA

Video Capture Device” is displayed under “System Properties” -

“Device Manager” - “Imaging Device”.

10

GB

Uninstalling the Drivers, “Camera Setting Utility” and

“SONY USB CAMERA Viewer”

If installation of the drivers fails, use the following procedure to

uninstall the drivers. Then perform the installation procedure again.

Note

First close down the software to be used with the camera.

1 Disconnect your camera from the computer.

2 Click the [Start] button on the task bar, point to [Setting], and then

click [Control Panel].

The “Control Panel” appears.

3 Double-click [Add/Remove Programs] in the “Control Panel”.

The “Add/Remove Programs” dialog box appears.

4 Click the [Install/Uninstall] tab.

5 Click [SONY USB CAMERA Installer] in the “application list” to

highlight the item.

11

GB

6 Click [Add/Remove].

The uninstaller starts up, and “SONY USB CAMERA Installer”

appears.

7 Choose “Remove SONY USB CAMERA Installer,” and then click

[Finish].

The programs and files related to the “SONY USB CAMERA

Installer” are removed.

8 Click [Close].

9 Restart the computer.

12

GB

Using Your Camera

This section describes how to attach your camera to the computer and

how to handle your camera.

Note

• Do not connect or disconnect the camera’s USB cable during startup or shut down of

Windows. This could cause your camera or computer to malfunction.

• Do not connect or disconnect the camera’s USB cable during startup or shut down of

software used with the camera. This could result in unstable operation of the computer.

Connecting to a Notebook Computer

Attach your camera to the notebook computer, and then connect the

USB cable to the USB connector on the notebook computer.

Extend the arm plate by hand and hook the camera onto the display panel as shown in the

figure below.

You can connect or disconnect your camera to or from the computer

while the computer is powered on. For details on the location of the

USB connector, please see the instruction manual for the notebook

computer.

Arm plate

13

GB

Continued

Connecting to a Desktop Computer

Connect the USB cable from your camera to the USB connector on the

desktop computer.

You can connect or disconnect your camera to or from the desktop

computer while the computer is powered on. For details on the location

of the USB connector, please see the instruction manual for the

desktop computer.

Detaching the Camera

Note

• If you detach your camera while the computer is powered on, be sure to perform the

following procedures. If this is not performed correctly, there is a risk that the

computer may fail to operate correctly.

• When you detach the camera while the computer power is off, step 1 is not required.

However, when the USB cable is disconnected with the computer in the power saving

mode, the system may not recognize the camera if the USB cable is plugged in again.

1 Close the software used with your camera.

2 Unplug the USB cable.

Note

• Unplugging by grasping a part of the cable may result in damage.

Be sure to hold the connector section when unplugging.

• When removing your camera from the attachment adapter, widen the arm plate using

your fingers while detaching the camera.

14

GB

Shooting With the Camera

Application software is used to shoot pictures. Be sure to install the

application software in advance.

1 Connect your camera.

You can connect or disconnect your camera to and from the

computer while the computer is powered on. For details, see

“Connecting to a Notebook Computer” (page 12) or “Connecting

to a Desktop Computer” (page 13).

2 Start the application software.

3 Turn the focus ring to adjust the focus.

4 Press the CAPTURE button to shoot pictures.

In addition to attaching the camera to the computer, you can also

use it held in hand as shown in the figure to shoot from various

angles.

z

• When shooting still pictures, you can confirm the picture before actually capturing it

by pushing the CAPTURE button half way in.

• Whether or not still pictures can be shot, depends on the application software.

15

GB

Notes on Use

On placement

During use or storage, do not place your

camera in the following places. It may

result in malfunction.

• Places where the temperature

becomes excessively high.

Do not leave your camera in a car

parked in direct sunlight. This could

result in deformation and damage.

• In direct sunlight or near heat sources

This could result in deformation and

damage.

• Dusty locations, beaches or other

places with much sand or dust.

When using your camera on a sandy

beach or dusty location, be sure that

the camera is not exposed to sand or

dust. Sand or dust may cause the

camera to malfunction and sometimes

the malfunction cannot be repaired.

• Do not point the lens directly at the

sun.

The lens may be damaged and image

burn-in, etc. may result. Be careful

when placing the camera under

sunlight or by a window.

• Keep the unit away from strong

magnetic fields. Recording may not

perform normally.

On operation

• Do not disconnect the camera’s USB

cable while the application is in

operation. This may result in

malfunction.

• Do not place objects on top of your

camera.

• Avoid exposure to rapid temperature

fluctuations. Do not use your camera

immediately after it is brought from a

cold to a warm location, or if the

temperature of the room is raised

rapidly. Moisture may condense

inside the camera. Wait a while

before using the camera.

On transportation

Retain the shipping box. It may come in

handy if the camera has to be

transported in the future.

On the lens

Do not touch the lens of the camera.

On discs

Observe the following precautions to

protect the data recorded on discs.

• Do not affix paper, etc. to the disc,

and do not scratch the disc.

• Do not touch the side of the disc with

recorded data (playback side).

• Do not store a disc where it is subject

to excessive dust, direct sunlight, high

humidity, or near heat sources.

• Do not spill liquids on the disc.

• To protect valuable data, always

place the disc in its case for storage.

16

GB

Maintenance

Cleaning the camera

Wipe with a dry soft cloth. If very dirty,

use a soft cloth slightly moistened with

a mild detergent solution. Do not use

thinner, benzine, alcohol, etc. as these

can damage the finish of the camera.

Cleaning the lens

Clean the lens surface with a blower

brush or a soft brush to remove dust. If

very dirty, use a commercially available

lens cleaning cloth.

Cleaning discs

• Fingerprints and dust on the surface

of a disc may cause read errors.

Always retain discs in clean

condition.

• For normal cleaning, hold the disc by

its edge and use a soft cloth to wipe

the surface from the centre out.

• If the disc is very dirty, moisten a soft

cloth with water, wring it out well,

and use it to wipe the surface of the

disc from the center out. Wipe off any

remaining moisture with a dry soft

cloth.

• Do not use solvents such as benzine,

thinner, commercially available

cleaners or anti-static spray, as they

may cause damage to the disc.

17

GB

USB Camera

350,000 pixels (310,000 effective

pixels)

Image device

1/6” CCD (Charge Coupled Device),

350,000 pixels

Lens

2 groups with 2 lenses, F2.8

Focal distance f = 2.8 mm

(f = 40 mm, when converted into a 35

mm still camera)

White balance

Auto/Indoor/Outdoor/Hold

Shutter speed

Auto/Fixed/Hold

Video capture formats/sizes

YUY2/RGB 24 bits/UYVY

40 × 30, 80 × 60, 160 × 120, 320 × 240,

640 × 480

Display frame rate

Max. 30 frames/sec.*

(40 × 30, 80 × 60, 160 × 120, 320 ×

240, 640 × 480)

* Differs with the computer

specifications and application usage

conditions.

Power consumption

Approx. 1 W

External dimensions (W/H/D)

Approx. 1.4 × 2.6 × 1 in

36 × 67 × 25 mm

Cable length

About 27.6 in

70 cm

Mass

Approx. 45 g (main unit only)

Operating Conditions/Storage

Conditions

Operating temperature:

41°F to 95°F (temperature gradient

18°F/h or lower)

5°C to 35°C (temperature gradient

10°C/h or lower)

Operating humidity:

20% to 80% RH (no condensation).

However, the relative humidity at 95°F/

35°C should be 65% or lower (wet-bulb

temperature 84°F/29°C or lower)

Storage temperature:

-4°F to 140°F (temperature gradient

18°F/h or lower)

-20°C to 60°C (temperature gradient

10°C/h or lower)

Storage humidity:

10% to 90% RH (no condensation).

However, the relative humidity at

140°F/60°C should be 20% or lower

(wet-bulb temperature 95°F/35°C or

lower)

Supplied Accessories

• Install disc (CD-ROM × 1) with

drivers, bundled software, and a

software manual (PDF)

• USB camera “Operating Instructions”

(this manual)

• Quick Start

• Pouch

• Camera monitor mount

• Microphone

• Warranty card

Design and specifications are subject to

change without notice.

Main Specifications

18

GB

The computer does not

recognize my camera.

Troubleshooting

Please use the following checklist for troubleshooting before consulting your dealer.

Should any problem persist, please consult your nearest Sony dealer.

Symptom Cause/Remedy

• The USB cable is not connected correctly.

t After closing any running software, connect the cable

correctly.

• Driver was not installed correctly.

t Once uninstall the driver, reboot the computer and then

attempt to install the driver again. (See page 10.)

If this fails, perform the following steps.

1 Connect your camera to the computer.

If the “Add New Hardware Wizard” appears, click [Cancel].

2 With your camera connected, click the [Start] button in the task

bar, point to [Setting], and then click [Control Panel].

The “Control Panel” appears.

3 Double-click [System].

“System Properties” appears.

4 Click the [Device Manager] tab to display the device list.

5 If any of the following items is displayed among the following

devices, delete the item.

- [USB Audio Device] in [Sound, video and game controllers]

- [Unknown device] or [Composite USB Device] in [Other

devices]

- [USB compatible device] in [Universal serial bus controller]

6 Disconnect your camera from the computer, and then restart the

computer.

7 Install the driver from the install disc, and then connect your

camera.

• OS used is not Windows98, Windows 98 SE, Windows 2000

Professional or Windows Millennium Edition.

t Use Windows 98, Windows 98 SE, Windows 2000

Professional, or Windows Millennium Edition.

• USB root hub is not recognized.

t Correctly install Windows 98, Windows 98 SE, Windows

2000 Professional, or Windows Millennium Edition.

• USB can no longer be used.

t Confirm the computer’s system properties.

19

GB

Continued

Symptom Cause/Remedy

The computer does not

recognize my camera.

When shooting a bright

subject on a dark

background, the image on the

display shows vertical stripes

radiating from the subject.

The image shown in the

finder of commercially

available software, etc. is

grainy.

Still pictures or video clips

captured with your camera

appear grainy on the display.

When commercially available

application software is used

to capture moving pictures

from your camera, some

frames are lost and the sound

falls out.

Black images are captured

when moving pictures or still

pictures are captured.

The images from your

camera freeze for several

seconds.

The images from the camera

are not displayed.

• When your camera is connected via USB hub, sufficient

power is not supplied from the hub.

t

Use a USB hub capable of supplying 500 mA for each port.

This phenomenon is called “smear”. It is not a malfunction.

When a fast moving subject is shown in the finder, step-like

features in horizontal direction may appear, or horizontal stripes

may appear in moving parts. However this is not a malfunction.

• Images shot under fluorescent light may contain light

reflections.

• If the captured image contains dark parts, red or green noise

sometimes appears.

• The lens is dirty.

t Clean the lens.

• The lens is out of focus.

t Adjust the focus using the focus ring.

• When multiple applications are running, the processing

capacity of the computer may be exceeded. Close applications

not used.

• The computer’s power management function is activated.

t Check the CPU speed setting. For details on settings, see

the instruction manual for the computer.

Black images are captured temporarily during software startup

or immediately after the image size is changed.

t Capture the desired image after it is displayed.

In the following instances, the images may freeze for several

seconds. This is not a malfunction.

• When a keyboard short cut operation involving Fn keys is

performed.

• When the load on the CPU is heavy.

• Multiple application software programs for capturing images

are running simultaneously.

t Close all but one of the applications.

• Video memory has become insufficient due to the computer’s

image mode or number of colours, or as a result of other

circumstances.

t Lower the resolution or reduce the number of colours.

• If the images from the camera do not appear even after

performing the above steps, restart the computer.

20

GB

Symptom Cause/Remedy

After connecting the USB

cable, the “Add New

Hardware Wizard” appears.

The computer does not enter

the power saving mode, but

returns immediately, or the

operation of Windows

becomes unstable.

Even when the camera is in

use, the computer’s LCD

display becomes dark, and

the computer enters a power

saving mode, such as system

idle, suspend or hibernation.

The computer does not return

from the video standby mode.

• The device driver is not installed.

t Click [Cancel] of the [Add New Hardware Wizard], and then

remove the USB cable from the USB connector. Then install

the driver by following the procedure described in “Installing

the Drivers, “Camera Setting Utility” and “SONY USB

CAMERA Viewer”” (see page 6).

Close all software in use, and then restart the computer. If restart

fails, refer to the instruction manual for the computer and turn off

the power.

The power saving mode is entered even if a USB device is in use.

t If you are using a desktop computer, and timer settings, such

as system standby, have been made, set the timer to OFF

using [Power Management] in the [Control Panel].

t The power saving mode is released when you operate the

computer’s touch pad, mouse or keyboard.

The power saving mode is released when you operate the

computer’s touch pad, mouse or keyboard. For details, see the

instruction manual for the computer.

La pagina sta caricando ...

Sony CMR-PC1 USB Manuale utente

Sony CMR-PC1 USB Manuale utente

in altre lingue

Documenti correlati

Altri documenti