B4.TWT.TK
B4.40.2TK
B4.65.2TK
B4.69.2TK
FULL RANGE SPEAKERS
CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to
the unit, fire and/or possible injury.
MISE EN GARDE : avant d'entamer l'installation, déconnectez la broche négative (-) de la batterie
pour éviter tout risque de blessures, d’incendie ou de dommages à l'appareil.
PRECAUCIÓN: Antes de la instalación, desconecte el terminal negativo de la batería (-) para prevenir
daño a la unidad, incendio y/o posibles lesiones.
VORSICHT: Entfernen Sie vor dem Einbau den negative Batteriepol, um Schäden am Gerät, Feuer bzw.
mögliche Verletzungen zu vermeiden.
ATTENZIONE: Prima dell’installazione, scollegate il terminale negativo (-) della batteria per evitare
danni all’unità, pericoli d’incendio e/o potenziali lesioni personali.
!
!
!
!
!
FULL RANGE SPEAKERS
Installation — English
Since some of these Coaxial Speakers are most
often used as direct replacements for stock
speakers and are shipped without grilles, some
of the following instructions will not apply. For
custom installations see your Authorized Lightning
Audio Dealer.
1. Determine where the speakers will be
mounted. Ensure an area large enough for the
speaker to mount evenly. Be sure that the
mounting location is deep enough for the
speaker to fit; if mounting in a door, operate all
functions (windows, locks, etc.) through their
entire operating range to ensure there will be
no interference from the speaker.
2. Refer to the specification chart to determine
the proper diameter hole to cut for your
speaker model.
3. Using the plastic mounting ring as a template,
mark the locations for the mounting screws.
Drill the holes with a 1/8" bit.
4. Feed the speaker wires through the cutout and
connect to the speaker terminals. Be sure to
observe proper polarity when connecting the
wires. The speaker's positive terminal is
indicated with a "+".
5. Fit the ring and speaker to the cutout. Mount
them using the enclosed screws. Fit the grille
over the ring and press gently, but firmly,
into place.
Installation — Français
Comme certains de ces haut-parleurs sont
souvent utilisés directement en remplacement des
haut-parleurs d'origine et sont livrés sans grilles
certaines des recommandations suivantes ne
s'appliqueront pas. Pour des installations
personnalisés voyez votre dealer agréé
Lightning Audio.
1. Déterminer l'endroit où le haut-parleur sera
monté. Assurez-vous que cet endroit est
suffisamment large et profond pour monter le
haut-parleur de manière équilibrée. Si le
haut-parleur est monté dans une porte
assurez-vous que toutes les commodités
de la porte fonctionnent complètement et
correctement sans que le haut-parleur ne leur
fasse obstruction (lève-vitre, verrouillage, etc.).
2. Reportez-vous au tableau des spécifications
techniques pour déterminer le bon diamètre
de coupe du trou destiné au haut-parleur.
3. Utilisez l'anneau en plastique comme modèle
et localisez l'emplacement des vis. Préforez les
trous avec une méche de 3 mm.
4. Faites passer les fils de connexion au travers
du trou et de l'anneau en plastique et
connectez les aux bornes du haut-parleur.
Veuillez à bien observer les polarités. La
borne positive du haut-parleur est marqué
avec un point.
5. Fixez l'anneau et le haut-parleur autour du
trou avec les vis livrées. Adaptez le gril
au-dessus de l'anneau et de la pression
doucement, mais fermement, dans l'endroit.
Installación — Español
La mayoria de estos altavoces se usan
principalmente como reemplazo directo de los
altavoces de origen del vehiculo y no vienen
equipados con rejillas, por lo que algunas de las
siguientes instrucciones no serán aplicables. Para
una instalación personalizada consulte a su
distribuidor autorizado Lightning Audio.
1. Determine donde han de montarse los
altavoces. Asegúrese de que hay espacio
suficiente tanto de área como de profundidad
para alojar el altavoz. Si el montaje es en una
puerta, todas las funciones han de ser
respetadas (alzacristales, cierres, etc.).
2. Consulte la hoja de caracteristicas para
determinar el diametro del agujero a realizar
para su modelo de altavoz.
3. Use los anillos de montaje de plático como
plantilla. Marque la posición de los tornillos de
anclaje.
4. Pase el cable de altovoz a través del anillo de
plástico y conéctelo a los terminales del
altavoz. Observe la polaridad. El terminal
positivo está marcado con un punto.
5. Ajuste el anillo y el altavoz al orificio. Móntelo
utilizando los tornillos suministrados. Quepa la
parrilla sobre el anillo y la prensa suavemente,
pero firmemente, en lugar.
Einbau — Deutsch
Da einige Vollbereichslatusprecher als direkter
Ersatz, für die vom Hersteller mitgelieferten
Lautsprecher dienen, treffen einige Punkte dieser
Bedienungsanleitung evtl auf Sie nicht zu. Bei
Rückfragen wenden Sie sich bitte an Ihren
Lightning Audio.
1. Legen Sie den Einbauort des Lautsprechers
fest. Seien Sie sicher, dab die Lautsprecher auf
beiden Seiten passen. Stellen Sie fest, ob
genung Einbautiefe vorhanden ist. Beim
Einbau in die Tür sollten Sie sich vergewissern,
dab keine Funktion der Tür beeinträchtigt wird.
2. Sie finden unter “Specification” die richtigen
Masse für den Ausschnitt.
3. Benutzen Sie en Einbauring als Schnittvorlage
und markieren Sie die Löcher für die
Befestigungsschrauben. Bohren Sie dann
dafür die passenden Löcher.
4. Führen Sie die Lautsprecherkabel durch die
Öffnung und durch den Montagering und
klemmen Sie dann den Lautsprecher den.
Positiv ist mit einem farbigen Punkt markiert.
5. Montieren Sie nun den Montagering und den
Lautsprecher mit den mitgelieferten
Schrauben. Passen Sie den Grill über dem
Ring und der Presse leicht, aber fest, in Platz.
Installazione — Italiano
Essendo gli altoparlanti a gamma estesa
normalmente impiegati negli alloggiamenti previsti
dai costruttori delle auto ed essendo spediti senza
griglie, alcune delle indicazioni seguenti potrebbero
non adattarsi al Vostro caso. Per installazioni
personalizzate contattate il Vostro installatore
autorizzato Lightning Audio.
1. Determinate la zona in cui installare gli
altoparlanti. Assicuratevi che lo spazio sia
sufficiente ad un corretto posizionamento.
Assicuratevi anche che la profonditá sia
sufficiente. Se l'installazione avviene in una
porta, controllate che tutte le parti meccaniche
(meccanismi dei vetri e chiusure centralizzate)
possano funzionare nell'intero loro arco
operativo.
2. Fate riferimento alla tabella con le specifiche
tecniche per determinare il diametro del foro
da praticare.
3. Impiegate l'anello in plastica di supporto della
griglia come dima per il posizionamento dei
fori di fissaggio. Praticate fori da 3,5 mm.
4. Passate i cavi attraverso il foro e l'anello
in plastica della griglia e collegateli
all'altoparlante. Controllate la polaritá (il
positivo sull'altoparlante é indicato da
un pallino).
5. Accostate l'anello e l'altoparlante al foro e,
impiegando le viti a dotazione, fissate il tutto.
Inserisca delicatamente, ma saldamente la
griglia sopra l'anello e la pressa, nel posto.
Check our website for updates on your products.
www.LightningAudio.com
INSTALLATION REFERNCE
SPECIFICATIONS
INSTALLATION
Model- Lightning Audio B4.TWT.TK B4.40.2TK B4.65.2TK B4.69.2TK
Nominal Diameter (inch) 1 4 6.5 6 x 9
Description Tweeter 2-way 2-way 3-way
Nominal Impedance ( ) 4444
Frequency Response 1600Hz-20KHz 100Hz-20KHz 55Hz-20KHz 50Hz-20Khz
Sensitivity (SPL@1w/1m) 91dB 87dB 90dB 90dB
Power (Watts RMS) 20 30 40 70
Power (Watts Maximum) 60 90 120 210
Features
Cone Kapton Polypropylene Polypropylene Polypropylene
Surround –– Butyl Rubber Butyl Rubber Butyl Rubber
Tweeter Ti + Silk Polyethylene Polyethylene Polyethylene
Installation
Mounting Diameter (inch) –– 3.72 5.70 6.00 x 8.70
Mounting Diameter (mm) –– 94.5 145 153 x 221
Mounting Depth (inch) –– 1.49 2.72
3.15
Mounting Depth (mm) –– 38 69 80
Mounting Hole
Screw
Speaker
LIMITED WARRANTY INFORMATION
06/08 B.M.
1230-55272-01 Printed in China
Lightning Audio offers a limited warranty on products on the following terms:
• Length of Warranty
Speakers
One year parts and labor warranty. Requires proof of purchase.
Amplifiers
Bolt: One year parts and labor warranty. Requires proof of purchase.
Strike and Storm: One year parts and labor warranty. Requires proof of purchase.
Or, Two years parts and labor warranty if installed by a Authorized Dealer. Requires proof of purchase.
CT1, FM1, PC1 and CS1
One year parts and labor warranty. Requires proof of purchase.
• What is Covered
This warranty applies only to Lightning Audio products sold to consumers by Authorized Lightning Audio Dealers in the
United States of America or its possessions. Product purchased by consumers from an Authorized Lightning Audio
Dealer in another country are covered only by that country’s Distributor and not by Lightning Audio.
• Who is Covered
This warranty covers only the original purchaser of Lightning Audio product purchased from an Authorized Lightning
Audio Dealer in the United States. In order to receive service, the purchaser must provide Lightning Audio with a copy
of the receipt stating the customer name, dealer name, product purchased and date of purchase.
• Products found to be defective during the warranty period will be repaired or replaced (with a product deemed to be
equivalent) at Lightning Audio’s discretion.
• What is Not Covered
1. Damage caused by accident, abuse, improper operations, water, theft
2. Any cost or expense related to the removal or reinstallation of product
3. Service performed by anyone other than Lightning Audio or an Authorized Lightning Audio Service Center
4. Any product which has had the serial number defaced, altered, or removed
5. Subsequent damage to other components
6. Any product purchased outside the U.S.
7. Any product not purchased from an Authorized Lightning Audio Dealer
• Limit on Implied Warranties
Any implied warranties including warranties of fitness for use and merchantability are limited in duration to the period
of the express warranty set forth above. Some states do not allow limitations on the length of an implied warranty, so
this limitation may not apply. No person is authorized to assume for Lightning Audio any other liability in connection
with the sale of the product.
• How to Obtain Service
Please call 1-888-881-8186 for Lightning Audio Customer Service. You must obtain an RA# (Return Authorization
number) to return any product to Lightning Audio. You are responsible for shipment of product to Lightning Audio.
Always include Proof of Purchase. Mark RA# on outside of shipping carton.
• EU Warranty
This product meets the current EU warranty requirements, see your Authorized dealer for details.
Ship to: Electronics
Lightning Audio
Warranty Repair Department
2055 E. 5th Street
Tempe, AZ 85281
RA#: _________________________
Ship to: Speakers
Lightning Audio
Speaker Returns
3056 Walker Ridge Dr. Suite G.
Walker, MI 49544
RA#: ____________________
-
1
-
2
-
3
-
4
Lightning Audio B4.69.2TK Manuale utente
- Categoria
- Altoparlanti
- Tipo
- Manuale utente
