Shindaiwa 501SX Manuale utente

Categoria
Motoseghe
Tipo
Manuale utente
SHINDAIWA OWNER'S/OPERATOR'S
MANUAL
CHAIN SAW
English
(Original instructions)
Français
Deutsch
Italiano
Español
WARNING
Read the instructions carefully and follow the rules for safe
operation.
Failure to do so could result in serious injury.
2
Introduction
This chain saw is designed for cutting wood or wood products.
Do not cut solid metal, sheet metal, plastic or any non-wood materials.
National or local regulation can restrict the use of this chain saw.
It is important for you to understand all safety precautions correctly before using your chain saw.
Misuse of the chain saw can cause serious bodily injury.
Never let children operate the saw.
This manual shows rules of safe operation, proper use, servicing, and maintenance of your shindaiwa chain saw.
Follow these instructions in order to maintain a good operating condition and a long service life.
For future reference, you should keep this operator's manual.
If this operator's manual has become illegible through impairment or is lost, please purchase a new one from your shindaiwa deal-
er.
When renting or lending this machine to a person who will operate it, always include this operator's manual, which provides expla-
nation and instructions.
When transferring a product, please deliver it attaching the operator's manual.
Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are
subject to change without notice.
Illustrations may include optional equipment and accessories, and may not include all standard equipment.
The unit is delivered with guide bar and saw chain separated.
Install guide bar and chain.
If there is any clause in this manual that is hard to be understood, please contact your shindaiwa dealer.
Manufacturer
YAMABIKO CORPORATION
1-7-2 SUEHIROCHO, OHME, TOKYO 198-8760, JAPAN
Authorized Representative in Europe
CERTIFICATION EXPERTS B.V.
P.O. box 5047, Merwedeweg 2, 3621 LR Breukelen, The Netherlands
3
Contents
Decals and symbols............................................................................................................ 4
Rules for safe operation...................................................................................................... 5
1. General precautions .................................................................................................. 5
2. Kickback safety precautions ...................................................................................... 8
3. Other safety precautions............................................................................................ 9
Description........................................................................................................................ 11
Assembly .......................................................................................................................... 12
Mounting guide bar and chain ..................................................................................... 12
Operation .......................................................................................................................... 13
Fuel and lubricant ........................................................................................................ 13
Chain lubricant............................................................................................................. 13
Cap indication.............................................................................................................. 13
Winter operation .......................................................................................................... 14
Starting the cold engine............................................................................................... 15
Starting the warm engine............................................................................................. 16
Running ....................................................................................................................... 16
Stopping the engine..................................................................................................... 17
Checking chain tension................................................................................................ 17
Chain lubrication test ................................................................................................... 17
Pre cutting test............................................................................................................. 17
Correct use of chain brake................................................................................................ 18
Chain brake ................................................................................................................. 18
Checking the brake function of the brake .................................................................... 19
Release the chain brake.............................................................................................. 19
Non-manual chain brake.............................................................................................. 19
Cutting instruction .............................................................................................................20
General........................................................................................................................20
Felling a tree................................................................................................................ 21
Limbing ........................................................................................................................22
Bucking........................................................................................................................ 22
Tension and compression in timber............................................................................. 23
Service maintenance guide .............................................................................................. 24
Troubleshooting ................................................................................................................ 25
Saw chain maintenance.................................................................................................... 26
Service.............................................................................................................................. 28
Air filter ........................................................................................................................ 28
Check fuel system ....................................................................................................... 28
Fuel filter......................................................................................................................28
Oil filter ........................................................................................................................ 28
Spark plug ................................................................................................................... 28
Guide bar..................................................................................................................... 29
Sprocket / Clutch drum ................................................................................................ 29
Carburettor .................................................................................................................. 29
Automatic oiler............................................................................................................. 29
Cylinder fins (Cooling system)..................................................................................... 30
Silencer........................................................................................................................30
Replacement guide bar and chain............................................................................... 30
Storage ............................................................................................................................. 31
Long term storage (Over 30 days)............................................................................... 31
Disposal procedure........................................................................................................... 32
Specifications.................................................................................................................... 33
Declaration of conformity .................................................................................................. 34
4
Decals and symbols
DANGER WARNING CAUTION
This symbol accompanied by the
word "DANGER" calls attentions to
an act or a condition which will
lead to serious personal injury or
death of operators and bystanders.
This symbol accompanied by the
word "WARNING" calls attentions
to an act or a condition which can
lead to serious personal injury or
death of operators and bystanders.
"CAUTION" indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
Circle and slash symbol
means whatever is
shown is prohibited.
NOTE IMPORTANT
This enclosed message provide tips
for use, care and maintenance of the
unit.
Framed text featuring the word "IM-
PORTANT" contains important infor-
mation about the use, checking,
maintenance and storage of the prod-
uct described in this manual.
Symbol form / shape Symbol description / application Symbol form / shape Symbol description / application
Carefully read the operator's manual Chain oil fill
Wear eyes, ears and head protection Chain oiler adjustment
Warning!
Kickback may occur!
Decompression device
Emergency stop Carburettor adjustment
- Idle speed
Chain brake operation Guaranteed sound power level
Oil and petrol mixture
Locate this safety decal on your unit.
The complete unit illustration found in the "Description" sec-
tion will help you locate them.
Make sure the decal is legible and that you understand and
follow the instructions on it.
If a decal cannot be read, a new one can be ordered from
your shindaiwa dealer.
5
Rules for safe operation
1. General precautions
Operator's manual
Read the operator's manual for your chain saw carefully.
Be thoroughly familiar with the chain saw's controls and how to use the chain saw properly.
Failure to follow instructions could lead to personal injury.
If you have any questions or problems, please contact your shindaiwa dealer.
Physical condition
Do not operate a chain saw when you are fatigued or under the influence of alcohol or
drugs.
You should be in good physical and mental health in order to handle your chain saw safely.
Errors in judgement or execution can be serious or fatal.
If you have any physical condition which strenuous work could worsen, check with your phy-
sician before using a chain saw.
Do not operate when ill or fatigued, or under the influence of any substance or medication
which could affect your vision, dexterity or judgement.
The ignition system of this product generates electromagnetic fields during operation.
Magnetic fields can cause pacemaker interference or pacemaker failure.
To reduce health risks, we recommend that pacemaker users consult their physician and
the pacemaker manufacturer before operating this product.
Personal equipment
Always wear approved goggles to protect your eyes.
Wood chips, dust, snapping branches and other debris can be thrown by the cutting chain
into the operator's facial area.
Goggles may also offer limited protection in the event of the cutting chain hitting the oper-
ator in the eye area.
If conditions warrant that a ventilated face shield be worn, goggles must be worn under-
neath it.
shindaiwa advises wearing hearing protection at all times.
If not followed, hearing loss can occur.
You should reduce the risk of hearing damage by wearing either "headset" type protectors
or ear plugs which are approved by an authorized organization.
All persons who make part of their living using chain saws should be tested periodically
for hearing deterioration.
Always wear a helmet when working with a chain saw.
A safety hard helmet is highly recommended when felling or working under trees, or when
objects can fall on you.
Wear heavy duty, non-slip gloves for improved grip, and also for protection against cold
and vibration.
Safety tip shoes or boots with non-slip sole should be worn.
Never wear loose clothing, unbuttoned jackets, flared sleeves and cuffs, scarves, tie-
strings, neckties, cords, chains, jewellery, etc. which could snag the saw chain or under-
brush.
Clothing should be of sturdy, protective material.
It should be snug-fitting to resist snagging, but roomy enough for freedom of movement.
Trouser legs should not be flared or cuffed, and should be either tucked into the boot tops
or trimmed short.
Safety vests, leg chaps and logger's pants of ballistic material are available.
It is the operator's responsibility to wear such additional protection if conditions warrant it.
Never operate a chain saw when you are alone.
Arrange to have someone remain within calling distance in case you need help.
CAUTION
Stuffing ears with cotton is not recommended.
6
Fuel
1. Oil tank cap
2. Fuel tank cap
A: Loosening direction
B: Tightening direction
Use an appropriate type of fuel container.
Bring an extinguisher or shovel in case of fire.
Despite the precautions which can be taken, operating a chain saw, or just working in the
forest, presents dangers.
Do not smoke or bring flame or sparks near to fuel supplies.
The fuel tank may be under pressure.
Always loosen the fuel cap and wait for pressure to be equalized before removing the cap.
When fuel tank cap or oil tank cap is difficult to remove by fingers, make sure that the
ignition switch is off, and put the starter handle into the groove of cap and turn it anti-
clockwise.
Fill the fuel tank outdoors over bare ground and install the fuel cap securely.
Do not pour fuel indoors.
Wipe any spilled fuel off the unit.
Never refuel while the engine is still hot, or fuel a running engine.
Do not store the unit with fuel in its tank, because a fuel leak could start a fire.
Always fill up the chain oil first, then fill up the fuel mixture.
DANGER
Petrol and fuel are extremely flammable.
If spilled or ignited by ignition source, it can cause fire and serious injury or prop-
erty damage.
Extreme caution is required when handling petrol or fuel.
After refuelling, tighten fuel cap firmly and check for leakage.
In case of fuel leakage, repair before starting operation since there is a danger of
fire.
7
Starting engine
Move the chain saw at least 3 m from the fuelling point before starting the engine.
Do not allow other persons to be near the chain saw when you are starting or cutting with
the chain saw.
Keep bystanders and animals out of the work area.
Do not let anyone hold wood for you to cut.
Do not start cutting until you have a clear work area, secure footing and a planned retreat
path from the falling tree.
Before you start the engine, make sure that the saw chain is not contacting anything.
Keep the handles dry, clean, and free of oil or fuel mixture.
Operate the chain saw only in well-ventilated areas.
Exhaust gas, oil mist (from chain saw lubrication) or saw dust is harmful to health.
Transportation
1. Guide bar cover
When transporting your chain saw, use the appropriate guide bar cover.
Carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and
the silencer away from your body.
Transport and storage
Always keep the engine shut off and make it certain that cutting device is securely cov-
ered. When transporting the machine, properly secure it to prevent flipping over, fuel
spillage and damage to the unit.
8
2. Kickback safety precautions
1. High kickback
In some cases, tip contact may cause a lightning-fast reverse reaction, kicking the guide
bar up and back toward the operator (this is called a rotational kickback).
Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back
toward the operator (this is called a linear kickback).
Either or these reactions may cause you to lose control of the saw and come in contact
with the moving chain, which could result in serious personal injury.
As a chain saw user, you should take several steps to keep your cutting jobs free from ac-
cident or injury.
With a basic understanding of kickback, you can reduce or eliminate the element of sur-
prise.
Sudden surprise contributes to accidents.
Understand that rotational kickback is preventable by keeping an unshielded bar nose from
touching an object or the ground.
Do not operate a chain saw with one hand!
Serious injury to the operator, helpers or bystanders may result from one-handed operation.
For proper control, always use two hands when operating a chain saw, one of which oper-
ates the trigger.
Otherwise, this can result in the chain saw "skating" or skidding, which can result in person-
al injury due to loss of control.
Be alert for the phenomena "skating" and "bouncing", greater risk from kickback.
Be cautious not to lose balance of your body due to "drop" at the end of a cut.
Keep a good firm grip on the saw which both hands, with the right hand on the rear han-
dle and the left hand on the front handle, when the engine is running.
Use a firm grip with thumbs and fingers encircling the chain saw handles.
A firm grip will help you reduce kickback and maintain control of the saw.
Two hands must be used to control the saw at all times.
Do not overreach or cut above chest height.
Make sure that the area in which you are cutting is free from obstructions.
Do not let the bar nose contact a log, branch, or any other obstruction which could be hit
while you are operating the saw.
Cutting at high engine speeds may reduce the likelihood of kickback.
But cutting at part-throttle or low engine speeds may be preferable to control the chain saw
in tight situations and may also reduce the likelihood of kickback.
Follow manufacturer's sharpening and maintenance instructions for the saw chain.
Use only replacement guide bars and chains specified by the manufacturer, or the ac-
ceptable equivalents of these guide bars and chains.
DANGER
Kickback safety precaution for chain saw users: kickback may occur when the nose
or tip of the guide bar touches an object or when the wood closes in and pinches the
saw chain in the cut.
9
3. Other safety precautions
Vibration and cold
It is believed that a condition called Raynaud's Phenomenon, which affects the fingers of cer-
tain individuals, may be brought about by exposure to cold and vibration.
Accordingly, your shindaiwa chain saw has an anti-vibration device designed to reduce the
intensity of vibration received through the handles.
Exposure to cold and vibration may cause tingling and burning followed by loss of colour and
numbness in the fingers. (White finger syndrome)
We strongly recommend you take the following precautions because the minimum exposure
which might trigger the ailment is unknown.
Keep your body warm, especially the head and neck, feet and ankles, and hands and
wrists.
Maintain good blood circulation by performing vigorous arm exercises during frequent
work breaks and also by not smoking.
Limit the number of hours of chain saw operation.
Try to fill a part of each work day with jobs other than chain sawing.
If you experience discomfort, redness and swelling of the fingers, followed by whitening
and loss of feeling, consult your physician before further exposing yourself to cold and
vibration.
Repetitive stress injuries
It is believed that over-using the muscles and tendons of the fingers, hands, arms and shoul-
ders may cause soreness, swelling, numbness, weakness and extreme pain to the areas just
mentioned.
To reduce the risk of repetitive stress injury, do the following:
Avoid using your wrist in a bent, extended or twisted position.
Instead, try to maintain a straight wrist position.
Also, when grasping, use your whole hand, not just the thumb and index finger.
Take periodic breaks to minimize repetition and rest your hands.
Reduce the speed and force in which you do the repetitive movement.
Do exercises to strengthen the hand and arm muscles.
See a doctor if you feel tingling, numbness or pain in the fingers, hands, wrists or arms.
Relative to EU directive "Vibration"
EU Directive "Vibration" (2002/44/EC) was designed to protect people from safety and health
risks arising from mechanical vibration of a machine by enforcing employers to limit a stand-
ardized 8 hour daily vibration exposure level, A(8).
Any person or organization that employs a person to operate a machine has to take the A(8)
value into account when letting the person use it.
Mechanical vibration values (equivalent vibration value) of this machine, which shall be used
as a guide to simplify the calculation of A(8) value, are as follows:
MODEL Type
Front / Left handle (m/s
2
)3.6
Rear / Right handle (m/s
2
)3.7
10
Machine conditions
Do not operate a chain saw that is damaged, improperly adjusted, or not completely and
securely assembled.
Do not operate the chain saw with a loose or defective silencer.
Be sure that the saw chain stops moving when the throttle control trigger is released.
If your saw is subjected to high loads due to a fall or impact, always perform inspection
and operation check in order to confirm if there is anything wrong before continuing work.
Cutting
Do not operate a chain saw in a tree unless you have been specifically trained to do so.
Keep all parts of your body away from the saw chain when the engine is running.
Use extreme caution when cutting small-size brush and saplings because slender ma-
terial may catch the saw chain and be whipped toward you or pull you off balance.
Stay on the uphill side when bucking or limbing logs which might roll when cut.
When cutting a limb that is under tension, be alert for spring-back so that you will not be
struck by the limb or chain saw when the tension in the wood fibres is released.
Cutting while on a ladder is extremely dangerous because the ladder can slip and your
control of the chain saw is limited.
Working aloft should be left to professionals.
Keep both feet on the ground.
Do not work from off-the-ground positions.
Stop the engine before setting the chain saw down.
Wood practices
Operating a chain saw safely requires a chain saw in proper working order, sound judge-
ment, and knowledge of the methods which should be applied in each cutting situation.
Do not let any person use your saw unless he has read this operator's manual and fully
understands its instructions.
Use your saw only to cut wood or wood products.
Do not cut solid metal, sheet metal, plastics or any non-wood materials.
Services
All chain saw service operations, other than items listed in the operator's manual main-
tenance instructions, should be performed by competent service personnel.
(For example, if an improper tool is used to hold the flywheel in order to remove the clutch,
structural damage to the flywheel could occur and subsequently could cause the flywheel
to burst.)
WARNING
Do not modify a chain saw in any way.
Only attachments and parts supplied by shindaiwa or expressly approved by shindai-
wa for use with the specific shindaiwa chain saw models are authorized.
Although certain unauthorized attachments are useable with the shindaiwa power-
head, their use may, in fact, be extremely dangerous.
CAUTION
Do not touch hot surfaces of cylinder cover and silencer after you used the chain saw.
11
Description
1. Spiked bumper - Device, fitted in front of the guide bar
mounting point, acting as a pivot when in contact with a
tree or log.
2. Silencer - The silencer controls the exhaust noise and
prevents hot, glowing particles of carbon from leaving the
silencer.
3. Front hand guard - Guard between the front handle and
the saw chain for protecting the hand from injuries and
aiding in control of the chain saw if the hand slips off the
handle.
This guard is used to activate the chain brake which is to
stop the saw chain rotation.
4. Decompression device - Device for lowering the com-
pression in the cylinder, to aid starting.
5. Choke control knob - Device for enriching the fuel / air
mixture in the carburettor to aid cold starting.
6. Rear handle (for the right hand) - Support handle locat-
ed towards the rear of the engine housing.
7. Rear hand guard - Extension on the lower part of the
rear handle for protecting the hand from the chain if it
breaks or degrooves.
8. Clutch cover - Protective cover to the guide bar, saw
chain, clutch and sprocket when the chain saw is in use.
9. Chain tension adjuster - Device to adjust chain tension.
10. Chain catcher - A projection designed to reduce the risk
of the operator's right hand from being hit by a chain
which has broken or derailed from the guide bar during
cutting.
11. Guide bar - The part that supports and guides the saw
chain.
12. Chain - Chain, serving as a cutting tool.
13. Type and serial number
14. Oil tank cap - For closing the oil tank.
15. Starter handle - The grip of the starter, for starting the
engine.
16. Fuel tank cap - For closing the fuel tank.
17. Throttle trigger - Device activated by the operator's fin-
ger, for controlling the engine speed.
18. Throttle trigger lockout - A safety lever which must be
depressed before the throttle trigger can be activated in
order to prevent the accidental operation of the throttle
trigger.
19. Ignition switch - Device for connecting and disconnect-
ing the ignition system and thus allowing the engine to be
started or stopped.
20. Air cleaner cover - Covers air filter.
21. Cleaner cover knob - Device for installing the air clean-
er cover.
22. Safety decal - Part number 890345-39231
23. Front handle (for the left hand) - Support handle locat-
ed at the front of the engine housing.
24. Cylinder cover - The cooling air flow grill.
It cover the cylinder, spark plug and silencer.
25. Operator's manual - Included with unit.
Read before operation and keep for future reference to
learn proper, safe operating techniques.
26. Tools - 13 x 19 mm T-wrench (combination screwdriver
/ spark plug socket).
27. Guide bar cover - Device for covering the guide bar and
saw chain during transport and other times when the
chain saw is not in use.
12
Assembly
Mounting guide bar and chain
1. Release chain brake
2. Two nuts
3. Clutch cover
Install guide bar and chain as follows.
Loosen two nuts and remove clutch cover.
Mount the bar and slide toward clutch to make saw chain installation easier.
4. Guide bar
5. Clutch
6. Bar hole
Install saw chain as shown.
(Ensure cutters are pointing in the right direction)
Release the chain brake, and install the clutch cover over the guide bar studs.
Tighten two nuts finger tight.
Ensure that chain tension adjuster fits into bar hole.
7. Tension adjuster
8. Direction to tension the chain
Hold the bar nose up and turn the adjuster clockwise until the chain fits snugly against
the underside of the bar.
A: Proper tension
B: Improper tension
Tighten both nuts with the bar nose held up.
Pull the chain around the bar by hand.
Loosen the adjustment if you feel tight spots.
WARNING
For your own safety, always stop the engine before performing any of the following
operations.
CAUTION
1. All adjustments should be made cold.
2. Always wear gloves when working on chain.
3. Do not operate with a loose chain.
NOTE
Move the chain brake lever (Front hand guard) fully rearward to remove or install the clutch
cover to the chain saw.
13
Operation
Fuel and lubricant
Fuel is a mixture of regular grade petrol and an air-cooled 2-stroke engine oil.
Minimum 89 Octane unleaded petrol is recommended.
Do not use fuel containing methyl alcohol or more than 10 % of ethyl alcohol.
Recommended mixture ratio; 50 : 1 (2%) for ISO-L-EGD Standard (ISO/CD13738),
JASO FC, FD grade and shindaiwa recommended oil.
- Never use two-stroke oil intended for water-cooled engines, motor-cycle engines.
- Do not mix directly in engine fuel tank.
- Avoid spilling petrol or oil.
Spilled fuel should always be wiped up.
- Handle petrol with care, it is highly inflammable.
- Always store fuel in approved container.
Chain lubricant
Proper lubrication of the chain while in operation minimizes friction between the chain,
the guide bar and sprocket and also clutch components such as needle bearing and
clutch assembly.
Use shindaiwa genuine chain oil or shindaiwa recommended chain oil specially formulat-
ed for bars and chains for proper lubrication.
These oils contain tackifiers, anti-aging and anti-oxidizing agents.
Consult your shindaiwa dealer for the proper chain oil.
Never use waste or reclaimed oil to avoid various malfunctions on oil system, clutch sys-
tem, chain and guide bar.
Lubrication problems caused by the use of improper oil will void the warranty.
Especially, vegetable based chain oil quickly turns to resin and adheres to oil pump,
chain, guide bar, clutch needle bearing and clutch assembly.
It causes malfunctions and shorten product life.
Flush chain oil system with mineral or chemical based chain oil after use, if it is required to
use vegetable oil due to local / municipal rule or any other reason.
For a short time emergency operation, fresh SAE 10W-30 motor oil can be used.
Cap indication
Fuel and oil tanks are indicated by the following illustrations.
Fuel tank cap
(Red)
Chain oil tank cap
(Black)
CAUTION
Whenever opening up the fuel tank, always loosen the cap very slowly and wait for
the tank pressure to be equalized before removing the cap.
14
Winter operation
1. Air shutter
2. Cold weather position (snowman mark)
3. Warm weather position (sun mark)
Use the air shutter to prevent carburettor troubles in winter.
Pull the choke knob and remove the air cleaner cover and the air filter.
Pull out the air shutter and insert it with the snowman mark facing up.
For operation above 5 ºC, return the air shutter to its original position (with the sun mark
facing up).
NOTE
Change the air shutter to its cold position (with the snowman mark facing up) when the
outside air temperature is 5 ºC or lower.
For operation above 5 ºC, return the air shutter to its original position.
Failing to do so will cause the engine to be overheated.
15
Starting the cold engine
A: Starter handle
1. Chain brake ACTIVATED position
2. Ignition switch (Run)
3. Decompression device
4. Choke control knob (Close)
5. Choke control knob (Open)
Fill the fuel tank with fuel mixture.
It is not permitted to fill fuel above the shoulder level of fuel tank.
Fill the chain oil tank with lubricant.
Press hand guard forward.
(Chain brake ACTIVATED position)
Lift ignition switch up.
Press the decompression device.
Pull choke control knob all the way out.
Securely hold the chain saw.
Make sure guide bar and saw chain are not touching anything when starting the saw.
Pull starter handle several times until first firing sound is heard.
Push choke control knob all the way in.
Press the decompression device and pull starter handle again.
WARNING
After choke control knob is pulled and then knob is returned to original position,
throttle remains a little open (latch condition).
If engine is started in this latch condition, chain starts to turn.
Do not start engine before chain brake is activated.
CAUTION
1. After starting the engine, immediately squeeze and release throttle trigger for dis-
engaging throttle latch and returning engine to idle, and pull front hand guard to-
wards the operator immediately. (Chain brake RELEASED position)
2. Do not increase engine speed while chain brake is engaged.
3. Use the chain brake only in starting the engine or in emergencies.
4. Never use throttle latch for cutting.
Use it only when starting the engine.
NOTE
Do not pull starter rope out to the maximum position.
Do not allow starter handle to snap back against the casing.
16
Starting the warm engine
1. Chain brake ACTIVATED position
Confirm there is fuel and chain oil in the tanks.
Press hand guard forward.
(Chain brake ACTIVATED position)
Lift ignition switch up.
Press the decompression device.
Securely hold the chain saw.
Pull starter handle.
Choke may be used if necessary, but after first firing sound pull throttle trigger a little to
release throttle latch and choke.
After choke control knob is pulled and then knob is returned to original position, throttle re-
mains a little open (latch condition).
Running
1. Chain brake RELEASED position
2. Throttle trigger lockout
3. Throttle trigger
After engine starts, allow it to idle for a few minutes.
Pull front hand guard towards the operator immediately.
(Chain brake RELEASED position)
Squeeze throttle trigger gradually to increase engine revolution.
The chain starts moving when the engine reaches 3900 r/min approximately.
Ensure proper acceleration and lubrication of saw chain and guide bar.
Do not run the engine at high speed unnecessarily.
Be sure that saw chain stops moving when throttle trigger is released.
17
Stopping the engine
1. Throttle trigger
2. Ignition switch
Release throttle trigger and allow engine to idle.
Push ignition switch down.
Checking chain tension
Chain tension should be checked frequently during work and corrected if necessary.
Tension the chain as tight as possible, but so it can still be pulled easily along the bar by
hand.
Chain lubrication test
Hold the chain just above a dry surface and open the throttle to half speed for 30 sec-
onds.
A thin line of "thrown" oil should be seen on the dry surface.
Pre cutting test
Familiarize yourself with your chain saw before you start actual cutting.
For this purpose it may be wise to practice by cutting some small logs or limbs several
times.
Do not allow either people or animals into the work area.
Multiple operators - Keep a safe distance between two or more operators when working to-
gether simultaneously.
NOTE
If engine does not stop, pull choke control knob all the way out to stop engine.
Return the unit to your authorized shindaiwa dealer to check and repair ignition switch be-
fore starting the engine again.
WARNING
Make sure that the engine is shut off when checking chain tension.
NOTE
Always loosen clutch cover nuts before turning the chain tension adjuster, otherwise the
clutch cover and tensioner will be damaged.
18
Correct use of chain brake
Chain brake
The chain brake's function is to stop chain rotation after a kickback.
It neither prevents nor reduces kickback.
Do not depend on the chain brake for protection against kickback.
Even with a chain brake, depend on your own good sense and proper cutting methods just as
though there were no chain brake.
Even with normal use and proper maintenance, the response time of the brake may lengthen.
The following may interfere with the brake's ability to protect the operator:
Saw wrongly held too close to operator's body.
Kickback time may be too fast even for a perfectly maintained brake to work in time.
The operator's hand may not be in position to contact the hand guard.
Brake will not be tripped.
Lack of proper maintenance lengthens the brake's stopping time, making it less effective.
Dirt, grease, oil, pitch, etc. getting into the working parts of the mechanism may lengthen
the stopping time.
Wear and fatigue of the activating brake spring, and wear of the brake / clutch drum and
pivot points may lengthen the brake's stopping time.
A damaged hand guard and lever may render the brake inoperative.
DANGER
Kickback motion is very hazardous.
If the tip of the bar touches wood or the like, the guide bar kicks back in an instant.
The chain brake reduces the possibility of injury due to kickback.
Always check that chain brake works properly before use.
NOTE
For practice, while cutting a small tree, push the front guard forward to engage the
brake.
At all times, confirm whether the brake works properly before each task.
If the chain brake is clogged with wood chips, function of the brake deteriorates a little.
Always keep the device clean.
Do not increase engine revolutions while the chain brake is engaged.
Chain brake is used in emergencies.
Do not use it unless absolutely necessary.
When using throttle latch at starting, keep the chain brake in position.
And after starting the engine, release the brake immediately.
Never test the brake in an area where petrol fumes are present.
19
Checking the brake function of the brake
1. Place the chain saw on the ground.
2. Hold the handle with both hands and accelerate the engine to high speed by using the
throttle trigger.
3. Operate the chain brake by turning your left wrist against the front hand guard whilst grip-
ping the front handle.
4. The chain stop immediately.
5. Release the throttle trigger.
If the chain does not stop immediately, take the saw to your shindaiwa dealer to repair.
Release the chain brake
When front hand guard is fully pulled towards the operator, chain brake is released.
Non-manual chain brake
1). End of the guide bar may be placed at the height about 35 cm.
2). Rear handle should be gripped lightly with the right hand.
The non-manual chain brake stops the operation of the saw chain in such a manner that the
kickback action produced at the end of the guide bar non-manually actuates the chain brake.
To make sure that the non-manual chain brake operates properly, proceed as follows:
1. Stop the engine of the chain saw.
2. Operate the front and rear handles with hands (grip them lightly), so that the guide bar
may be placed at the height of about 35 cm as shown in Fig.
3. Softly detach the left hand from the front handle, and touch the end of the guide bar
against the wood or the like placed below so that the machine receives an impact.
(* at this time the rear handle should be gripped lightly with right hand)
4. The impact is transferred to the brake lever, which actuates the chain brake.
IMPORTANT
When checking the operation of the non-manual chain brake, use a soft surface substance
like wood to provide the impact so the saw chain is not damaged.
20
Cutting instruction
General
In all circumstances the operation of the chain saw is a one-man job.
It is difficult at times to take care of your own safety, so don't assume the responsibility for a
helper as well.
After you have learned the basic techniques of using the saw, your best aid will be your own
good common sense.
The accepted way to hold the saw is to stand to the left of the saw with your left hand on the
front handle so you can operate the throttle trigger with your right index finger.
Before attempting to fell a tree, cut some small logs or limbs.
Be thoroughly familiar with the controls and the responses of the saw.
Start the engine, see that is running properly.
Squeeze the trigger to open the throttle wide open, then start the cut.
It is not necessary to press down hard to make the saw cut.
If the chain is properly sharpened, the cutting should be relatively effortless.
Pushing the saw too hard will slow the engine and cutting will actually be more difficult.
Some material may adversely affect the housing of your chain saw.
(Example: palm tree acid, fertilizer etc.)
To avoid housing deterioration carefully remove all packed saw dust around clutch and guide
bar area and wash with water.
DANGER
Do not let the nose or tip of the guide bar touch anything while engine is running to
avoid kickback.
IMPORTANT
Acids from decaying palm tree sap may corrode crankcase and oil tank housings made of
aluminium and magnesium alloys.
To minimize the chance of this occurring, make sure to follow the cleaning procedure listed
below.
Make sure to clean metal parts from palm sap immediately after use.
Remove sprocket cover.
Clean wood chips and sawdust from cover and engine crankcase.
Never use metal tools for cleaning which may scratch the metal paint and allow
corrosion to develop.
Clean sap accumulation from metal parts with cloth and warm water soap.
Rinse with clean water and dry metal surfaces.
Apply a light coating of engine or bar and chain oil to metal parts after they are cleaned.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180

Shindaiwa 501SX Manuale utente

Categoria
Motoseghe
Tipo
Manuale utente