Sony KP-41PZ1D Manuale utente

Manuale d’ Istruzioni

IT

Projection TV

R

KP-41PZ1D

4-205-149-11(2)

Instruction Manual

GB

Ãδηγίες Ìρήσης

GR

DE

Bedienungsanleitung

2

3

GB

Instruction Manual

Thank you for choosing this Sony projection TV.

Before operating the projection TV, please read this manual thoroughly and retain

it for future reference.

Reading and Understanding this Instruction Manual:

• Use Getting Started if you wish to install the projection TV set and to get familiar

with the basic functions.

• Use Advanced Operation if you wish to know more about the additional features

of the projection TV set.

• Symbols used in the manual:

• Informs you of possible hazards

• Important information

• Information on a feature

• 1, 2 ... Sequence of instructions

• Shaded buttons on the remote control show the buttons you have to

press to follow the sequence of instructions.

• Informs you of the result of the instructions.

• The process continues on the next page to get final result.

MENU

K

Projection TV

4

Safety Information

WARNING

For Your Safety

All TVs operate on extremely high voltages. To prevent fire or electric shock, please follow the safety

procedures indicated below.

For General Safety

• Do not expose the set to rain or moisture.

• Do not remove the rear cover.

• For your protection, refer all servicing to qualified

personnel only.

For Safe Installation

• Do not install the projection TV in hot, humid or

excessively dusty places.

• Do not block or cover the ventilation openings. For

ventilation, leave a space of at least 10 cm all around

the set.

• Do not install the projection TV where it may be

exposed to mechanical vibrations.

• To obtain a clear picture, do not expose the screen to

direct illumination or direct sunlight. If possible, use

spot lighting directed down from the ceiling.

• After transporting the projection TV directly from a

cold to a warm location, or if the room temperature

has changed suddenly, pictures may be blurred or

show poor colour over portions of the picture. This is

because moisture has condensed on the mirrors or

lenses inside the projection TV. Let the moisture

evaporate before using the projection TV.

For Safe Operation

• Do not operate the projection TV set on anything other

than a 220-240V AC, 50Hz supply.

• Do not operate the projection TV if any liquid or solid

objects fall in through the ventilation slots. Have it

checked immediately.

• For environmental and safety reasons, it is

recommended that the projection TV set is not left in

standby mode when not in use. Switch off at the

mains.

• Do not disconnect the projection TV by pulling on the

power cable. Disconnect by removing the mains plug.

• In case of a thunderstorm, disconnect the projection

TV set from the main supply and the aerial. Otherwise

the set may be damaged by a lighting strike.

• Displaying a still picture for long periods of time, for

instance, when operating a video game or personal

computer and viewing a programme in 4:3 mode, may

damage the picture tube. To avoid this, keep the

picture contrast level low.

For Maintenance

• Clean the projection TV screen and cabinet with a soft

dampened cloth. Do not use any abrasive cleaners. As

a safety precaution, unplug the set before cleaning it.

• Dust and nicotine deposits may cause heat

accumulation inside the projection TV set.

In the long term this could be a safety risk and may

shorten the lifetime of your projection TV set.

Therefore have your set serviced about every five

years.

• Avoid touching the screen, and take care not to scratch

the surface with hard objects.

5

Table of Contents

Keys to read this Instruction Manual .................................................................................................. 3

For your Safety ........................................................................................................................................ 4

Getting Started

Overview

Checking the Accessories Supplied ......................................................................................... 6

Overview of TV Buttons ........................................................................................................... 6

Overview of Remote Control Buttons ..................................................................................... 7

First Time Operation

Step 1 - Installation

Inserting Batteries into the Remote Control ........................................................................... 8

Stabilizing the projection TV .................................................................................................... 8

Connecting the Aerial ................................................................................................................ 9

Switching on the projection TV ................................................................................................ 9

Step 2 - Basic Presetting

Selecting Language .................................................................................................................. 10

Automatically Tuning the TV using the Remote Control .................................................. 11

Changing the Programme Order of the TV channels ......................................................... 12

Advanced Operation

Advanced Presetting

Adjusting colour Registration (Convergence) ..................................................................... 13

Automatically Tuning the TV ................................................................................................. 14

Manually Tuning the TV ......................................................................................................... 15

Using the “Further Programme Preset” function................................................................ 16

Locking Programmes............................................................................................................... 17

Skipping Programme positions ............................................................................................. 18

Labelling a channel .................................................................................................................. 19

Advanced TV Operation

Adjusting the Picture ............................................................................................................... 20

Changing the screen mode ..................................................................................................... 21

Adjusting the Sound ................................................................................................................ 22

Using the Sleep Timer ............................................................................................................. 24

Teletext

Viewing Teletext ....................................................................................................................... 25

Optional Connections

Connecting Optional Equipment ........................................................................................... 26

Using Optional Equipment .................................................................................................... 27

Smartlink ................................................................................................................................... 28

Remote Control of other Sony Equipment ........................................................................... 28

Selecting the output source for the Euro AV connectors .................................................... 29

Using the “AV Label Preset” function .................................................................................. 30

Additional Information

Optimum Viewing Area .......................................................................................................... 31

On Screen display Menus Guide ........................................................................................... 32

Specifications ............................................................................................................................ 33

Troubleshooting ........................................................................................................................ 34

GB

6

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

Getting Started - Overview

Checking the Accessories Supplied

One Remote Control

(RM-892)

Two batteries (R6 type)

Getting Started - Overview

One safety foot

Overview of Projection TV Buttons

Auto

Convergence

button

On/Off

Switch

Press the flap on the

front of the projection TV

to reveal the front panel

(press on the mark )

S Video

Input

jack

Video

Input

jack

Headphone

jack

Auto

Tune

button

Audio

Input

jacks

Standby

indicator

Selecting

input

source

Volume

control

buttons

Programme

up or down

buttons

(selects TV

channels)

7

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

K

VIDEO TV

VTR 1 2 3 4 DVD

CH

Getting Started - Overview

Overview of Remote Control Buttons

To Temporarily Switch Off projection

TV

Press to temporarily switch off TV (the

standby indicator

on projection TV lights

up). Press again to switch on TV from

standby mode.

To save energy we recommend switching off

completely when TV is not in use.

After 15-30 minutes without a

signal and without any button being

pressed, the projection TV switches

automatically into standby mode.

Displaying On Screen Information

Press to display all on-screen indications.

Press again to cancel.

Selecting Input source

Press repeatedly until the desired input

symbol of the source appears on the screen.

Back to the channel last watched

Press to watch the last channel selected

(watched for at least 5 seconds).

Selecting Screen format

Press repeteadly to change the format of the

screen.

This button only works in Teletext mode.

Function

associated to this button does not

work with this set.

Joystick for menu selection

4 Scroll Up

$ Scroll Down

Z Previous menu or selection

z Next menu or selection

OK Confirms your selection

Selecting channels

Press to select the next or previous channel.

Displaying the menu system

Press to display the menu on the screen.

Press again to remove the menu display

from the screen.

Muting the Sound

Press to mute TV sound.

Press again to restore the sound.

VCR on/off

Press to switch your VCR on or off.

Selecting TV mode

Press to switch off Teletext or video input.

Selecting Teletext

Press to switch on Teletext.

These buttons do not work on this set.

Selecting channels

Press to select channels.

For double-digit programme numbers, e.g. 23,

press -/-- first, then the buttons 2 and 3.

If you enter an incorrect first digit, this should

be corrected by entering another digit (0-9)

and then selecting -/-- button again to enter

the programme number of your choice.

+++++++++++++++...

Selecting Sound mode

Press repeatedly to change the sound mode.

+++++++++++++++++...

Selecting Picture mode

Press repeatedly to change the picture mode.

+++++++++++++++++...

Adjusting TV Volume

Press to adjust the volume of the TV.

Besides TV functions, all coloured buttons as well as green

symbols are also used for Teletext operation. For more details,

please refer to the "Teletext" section of this instruction manual.

This button does not work on this set.

Displaying the time

Press to switch the time on or off

(available only when teletext is

broadcast).

VCR operation

For more details, please refer to

the section "Remote Control of

other Sony Equipment"

8

First time Operation - Installation

For safety purposes, the projection TV can be stabilized with the supplied safety foot.

Stabilizing the Projection TV

Fit the supplied safety foot in the support placed on the bottom of the set, as follows:

First time Operation - Installation

Inserting Batteries into the Remote Control

Make sure you insert the batteries using the correct polarities.

Always remember to dispose of used batteries in an environmental friendly way.

9

First Time Operation - Installation

Connecting the Aerial

Connect the projection TV plug to the

mains socket (220-240V AC, 50Hz).

Switching on the projection TV

Push in the On/Off switch on the front of the

projection TV.

First Time Operation - Installation

Connect a conventional aerial to the socket

marked on the rear of the projection TV.

10

LANGUAGE

English

Deutsch

Français

Italiano

Nederlands

Polski

Česki

Magyar

Eλλnvιkά

Select Language:

Confirm: OK

First Time Operation - Basic Presetting

Selecting Language

Use this function to change the language of the menu screens.

The first time that you switch on your projection TV, the LANGUAGE menu appears automatically.

However, if you need to change the language menu afterwards, select the menu Language in the

(PRESET) menu and

proceed in the same way as described below.

1 Press the on/off button on your projection TV set to switch on

your TV. The first time you press the on/off button on your TV set,

the language menu displays automatically on the TV screen.

2 Push the joystick on the remote control to $ or 4 to select the

language, then press OK to confirm your selection.

The Auto Tuning menu appears on the projection TV screen in the selected

language.

First Time Operation - Basic Presetting

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

LANGUAGE

English

Deutsch

Français

Italiano

Nederlands

Polski

Česki

Magyar

Eλλnvιkά

Select Language:

Confirm: OK

LANGUAGE

English

Deutsch

Français

Italiano

Nederlands

Polski

Česki

Magyar

Eλλnvιkά

Select Language:

Confirm: OK

Do you want to start

automatic tuning?

Yes

No

Confirm: OK

11

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

First Time Operation - Basic Presetting

Automatically Tuning the TV using the Remote Control

You need to tune the set to receive channels (TV Broadcast). By following the instructions below, this projection TV

automatically searches and stores all available channels for you.

After having selected the language, a new menu appears automatically on the projection TV screen asking you to

automatically tune the TV. However, if you need to change or repeat the tuning afterwards (e.g. when you move house),

select the menu Auto Programme in the

(PRESET) menu and proceed in the same way as described below or, please

refer to the section "Automatically Tuning the TV" of this instruction manual.

1 Press the OK button on the remote control to select YES.

A new menu appears automatically on the screen asking you to

check that the antenna is connected.

2 Confirm that the antenna is connected and then press the OK

button.

The automatic tuning starts and the message "AUTO

PROGRAMME" flashes on the screen.

This procedure could take some minutes. Please, be patient and

do not press any button.

When the automatic tuning is finished, the Programme Sorting menu

appears on the screen.

Notes: • To stop the automatic tuning, press the MENU button.

• If you stop the automatic tuning by pressing the MENU

button, the Programme Sorting menu does not appear

automatically on the screen.

First Time Operation - Basic Presetting

Please confirm that

antenna is connected

Confirm: OK

PROG

1

AUTO PROGRAMME

SYS

B/G

CHAN

C 26

LABEL

- - - - -

PROG SYS CHAN LABEL

PROGRAMME SORTING

B/G

0

1

2

3

4

5

6

7

8

9

BBC-W

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

C 28

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

Select PROG: + OK

Exit: MENU

Do you want to start

automatic tuning?

Yes

No

Confirm: OK

12

PROG SYS CHAN LABEL

PROGRAMME SORTING

B/G

0

1

2

3

4

5

6

7

8

9

BBC-W

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

C 28

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

Select PROG: + OK

Exit: MENU

a) If you do not wish to change the channel order:

1 Press the MENU button on the remote control to exit and return to

the normal TV screen.

Your projection TV is now ready for use.

b) If you wish to change the channel order:

1 Push the joystick on the remote control to $ or 4 to select the

programme number with the channel (TV Broadcast) you wish to

rearrange, then press OK.

2 Push the joystick to $ or 4 to select the new programme number

position for your selected channel (TV Broadcast), then press

OK.

The selected channel now moves to its new programme

position and the other channels move accordingly.

3 Repeat steps 1 and 2 if you wish to change the order of the other

channels.

4 Press the MENU button to exit and return to the normal TV screen.

Your projection TV is now ready for use.

First Time Operation - Basic Presetting

Changing the Programme Order of the TV channels

After all available channels (TV Broadcast) are captioned and stored, a new menu appears automatically on the screen to

change the order in which the channels appear on the screen.

However, if you wish to rearrange the order of the channels afterwards, select the menu Programme Sorting in the

(PRESET) menu and proceed in the same way as described in the b) section of this chapter.

B/G

0

1

2

3

4

5

6

7

8

9

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

PROGRAMME SORTING

Select Position:

Confirm: OK

SYS CHAN LABELPROG

PROG SYS CHAN LABEL

PROGRAMME SORTING

B/G

0

1

2

3

4

5

6

7

8

9

BBC-W

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

C 28

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

Select PROG: + OK

Exit: MENU

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

13

Advanced Operation - Advanced Presetting

Adjusting Colour Registration (Convergence)

Due to the earth’s magnetism, the picture might become undefined and you could see different colours on the outlines of

the images. In that case, proceed as follows:

Auto converge the Red, Green, and Blue

Lines

1 Press the flap on the front of the projection TV by pressing on the

mark to reveal the front control panel.

2 Press button on the projection TV.

The Auto Convergence function works for about 30 seconds. When the

white cross disappears from the screen, your projection TV is ready for use.

Notes:

The Auto Convergence function does not work:

• when no signal is input.

• when the input signal is weak.

• when the screen is exposed to spotlights or direct sunlight.

• when you watch the teletext broadcast.

If you wish a more accurate convergence

adjustment

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol , then push to z to

enter to the PRESET menu.

3 Push the joystick to $ or 4 to select Convergence, then push to z.

4 Push the joystick to $ or 4 to select “the line” (vertical and

horizontal lines in red and blue) you want to adjust.

: red vertical line (left/right adjustment)

: red horizonta line (up/down adjustment)

: blue vertical line (left/right adjustment)

: blue horizontal line (up/down adjustment)

Then press the OK button.

5 Push the joystick repeatedly to $, 4, Z or z to converge the selected

line with the green line in the centre, then press OK to confirm.

6 Repeat steps 4 and 5 to adjust the other lines, until all the lines have

overlapped to form a white cross.

7 Press the MENU button to exit and return to the normal TV screen.

Your projection TV is ready for use.

Advanced Operation - Advanced Presetting

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

14

Advanced Operation - Advanced Presetting

Automatically Tuning the TV

Besides the explanation in the section “Automatically Tuning the TV using the Remote Control“, by following the

instructions below, this projection TV also searches and stores automatically all available channels using just one button of

the projection TV set and one button of the remote control.

1 Press the flap on the front of the projection TV by pressing on the

mark to reveal the front control panel.

2 Press and hold in the button on the TV set for some seconds,

until a menu appears automatically on the screen asking you to

check that antenna is connected.

3 Confirm that the antenna is connected and then press the OK

button on the remote control.

The automatic tuning starts and the message "AUTO

PROGRAMME" flashes on the screen.

This procedure could take some minutes. Please, be patient and

do not press any button.

When the automatic tuning procedure is complete, the Programme Sorting

menu appears on the screen:

• If you do not wish to change the channel order, press the MENU button

on the remote control to exit and return to the normal TV screen.

• If you wish to change the channel order, proceed in the same way as

described in the chapter "Changing the Programme Order of the TV

channels", section b).

Note: To stop the automatic tuning, press the MENU button on the

remote control.

Advanced Operation - Advanced Presetting

Please confirm that

antenna is connected

Confirm: OK

Please confirm that

antenna is connected

Confirm: OK

PROG

1

AUTO PROGRAMME

SYS

B/G

CHAN

C 26

LABEL

- - - - -

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

15

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

Advanced Operation - Advanced Presetting

Manually Tuning the TV

Use this function to preset channels or a video input source one by one to the programme order of your choice.

1 Press the MENU button on the remote control to display the

menu on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the PRESET menu.

3 Push the joystick to $ or 4 to select Manual Programme Preset,

then push to z.

4 Push the joystick to $ or 4 to select on which programme number

you want to preset a channel, then push to z.

5 Push the joystick to $ or 4 to select the TV Broadcast system

(B/G for western european countries, D/K for eastern european

countries) or a video input source (AV1, AV2...), then push to z.

6 Push the joystick to $ or 4 to select the channel tuning, "C" for

terrestrial channels or "S" for cable channels, then push to z.

7 Press the number buttons to enter the channel number of the TV

Broadcast or push the joystick to 4 or $ to search for the next

available channel.

If you do not wish to store this channel, push the joystick to 4 or

$ to continue searching for the desired channel.

8 If this is the desired channel you wish to store, press the OK

button.

9 Repeat steps 4 to 8 if you wish to store more channels.

10 Press the MENU button to exit and return to the normal TV

screen.

Your projection TV is now ready for use.

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

B/G

0

1

2

3

4

5

6

7

8

9

PROG SYS CHAN

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

LABEL

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

MANUAL PROGRAMME PRESET

B/G

0

1

2

3

4

5

6

7

8

9

PROG SYS CHAN

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

LABEL

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

MANUAL PROGRAMME PRESET

B/G

0

1

2

3

4

5

6

7

8

9

PROG SYS CHAN

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

LABEL

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

MANUAL PROGRAMME PRESET

B/G

0

1

2

3

4

5

6

7

8

9

PROG SYS CHAN

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

LABEL

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

MANUAL PROGRAMME PRESET

16

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

Advanced Operation - Advanced Presetting

Using the "Further Programme Preset" function

With this feature you can:

a) Even normally the automatic fine tuning (AFT) is operating, however you can manually fine-tune the TV to obtain a

better picture reception if the picture is distorted or

b) preset the AV3 output for the programme positions of channels with scrambled signals (eg from a pay TV decoder). In

this way a connected VCR records the unscrambled signal.

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the PRESET menu.

3 Push the joystick to $ or 4 to select Further Programme Preset,

then push to z.

4 Push the joystick to $ or 4 to select the relevant programme

number, then push to z repeatedly to select:

a) AFT or

b) DECODER.

The selected item changes colour.

5 a) AFT

Push the joystick to $ or 4 to fine tune the channel frequency over a

range of -15 to +15, then press the OK button.

Repeat steps 4 and 5a) if you wish to fine tune other channels.

b) DECODER

Push the joystick to $ or 4 to select AV

3 and press the OK.

The picture from the decoder connected to the Euro AV :3 on

the back of the projection TV will appear on this programme

number.

Repeat steps 4 and 5b) to preset the AV3 output for other

programme positions.

6 Press the MENU button to exit and return to the normal TV screen.

Your projection TV is now ready for use.

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

Off

AV1

Off

AV2

Off

On

0

1

2

3

4

5

6

7

8

9

PROG AFT DECODER

FURTHER PROGRAMME PRESET

Off

2

On

0

1

2

3

4

5

6

7

8

9

PROG AFT DECODER

FURTHER PROGRAMME PRESET

AV3

Off

On

0

1

2

3

4

5

6

7

8

9

PROG AFT DECODER

FURTHER PROGRAMME PRESET

17Advanced Operation - Advanced Presetting

Advanced Operation - Advanced Presetting

Locking Programmes

This feature enables you to prevent undesirable broadcasts appearing on the screen. We suggest you use this function to

prevent children from watching programmes you consider unsuitable.

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the PRESET menu.

3 Push the joystick to $ or 4 to select Parental Lock, then push to z.

4 Push the joystick to $ or 4 to select the programme number with

the channel you wish to block, then press the OK button.

The

symbol appears before the programme position to

indicate this programme is now blocked.

To unblock the programme, press the OK button again. The

symbol disappears.

5 Repeat step 4 if you wish to block other channels.

6 Press the MENU button to exit and return to the normal TV screen.

When you select a blocked programme the screen appears in black, with

symbol.

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

B/G

0

1

2

3

4

5

6

7

8

9

PROG

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

- - - - -

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

SYS CHAN LABEL

PARENTAL LOCK

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

18

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

Advanced Operation - Advanced Presetting

Skipping Programme positions

You can programme this projection TV to skip any unwanted programme numbers when they are selected with the

PROGR +/- buttons. To cancel this function afterwards, proceed in the same way as described below by selecting the

appropriate TV system (B/G or D/K) instead of "- - -" in step 5.

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the PRESET menu.

3 Push the joystick to $ or 4 to select Manual Programme Preset,

then push to z.

4 Push the joystick to $ or 4 to select the programme position you

want to skip, then push to z to enter to the SYS column.

5 Push the joystick to $ to select “- - -”, then press the OK button to

store.

6 Repeat steps 4 and 5 to skip other unused programme positions.

7 Press the MENU button to exit and return to the normal TV screen.

When changing channels (TV Broadcasts) with the PROGR +/- buttons,

the skipped programme positions do not appear. You can, however, still

select them using the number buttons.

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

B/G

0

1

2

3

4

5

6

7

8

9

PROG SYS CHAN

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

LABEL

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

MANUAL PROGRAMME PRESET

B/G

- - -

0

1

2

3

4

5

6

7

8

9

PROG SYS CHAN

MV-CH

TVE-1

TVE-2

ANT-3

TELE 5

C PLUS

- - - - -

CNN -

BBC-W

LABEL

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

MANUAL PROGRAMME PRESET

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

19

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

Advanced Operation - Advanced Presetting

Labelling a channel

Names for channels (TV Broadcasts) are usually taken automatically from Teletext if available. You can however name a

channel or an input video source using up to five characters (letters or numbers). Using this function, you can easily

identify which channel (TV Broadcasts) or video source you are watching.

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to $ to select the symbol, then push to z to

enter to the PRESET menu.

3 Push the joystick to $ or 4 to select Manual Programme Preset,

then push to z.

4 Push the joystick to $ or 4 to select the programme number with

the channel you wish to name.

5 Push the joystick to z repeatedly until the first element of the

LABEL column is highlighted.

6 Push the joystick to $ or 4 to select a letter or number (select “-” for

a blank), then push to z to confirm this character. Select the other

four characters in the same way.

7 After selecting all the characters, press the OK button.

8 Repeat steps 4 to 7 if you wish to label other channels.

9 Press the MENU button to exit and return to the normal TV screen.

When you select a named channel, the name appears for a few seconds on

the screen.

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

Auto Programme

Manual Programme Preset

Further Programme Preset

AV Label Preset

Programme Sorting

Parental Lock

Language

Convergence

PRESET

PROG SYS CHAN LABEL

MANUAL PROGRAMME PRESET

B/G

0

1

2

3

4

5

6

7

8

9

- - - - -

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

PROG SYS CHAN LABEL

MANUAL PROGRAMME PRESET

B/G

0

1

2

3

4

5

6

7

8

9

- - - - -

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

PROG SYS CHAN LABEL

MANUAL PROGRAMME PRESET

B/G

0

1

2

3

4

5

6

7

8

9

- - - - -

A- - - -

- - - - -

C 40

C 41

C 31

C 34

C 27

C 47

C 44

C 23

C 35

C 28

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

20

S

RM

892

PROGR

MENU

1

4

7

2

5

8

0

3

6

9

VIDEO TV

1 Press the MENU button on the remote control to display the menu

on the screen.

2 Push the joystick to z to enter the PICTURE CONTROL menu.

3 Push the joystick to $ or 4 to select the item you wish to change,

then push to z.

Refer to the table below to chose the item and for the effect of each

control:

4 Push the joystick to Z or z to alter the selected item, then press the

OK button to store the new adjustment.

5 Repeat steps 3 and 4 to alter the other items.

6 Press the MENU button to exit and return to the normal TV screen.

Picture Mode

Picture Mode Personal (for individual settings)

Movie (for films)

Live (for live broadcast programmes)

Brightness* Darker Brighter

Colour* Less More

Sharpness* Softer Sharper

Hue** Greenish Reddish

Contrast Less More

Reset Resets picture to the factory preset levels.

Format (for detalis refer to the section "Changing the

Screen Mode")

* Can only be altered if Personal Mode is selected.

** Only avalaible for NTSC colour signal (e.g: USA video tapes).

Advanced Operation - Advanced TV Operation

Adjusting the Picture

Although the picture is adjusted at the factory, you can modify it to suit your own taste.

Advanced Operation - Advanced TV Operation

Changing the Picture Mode Quickly

You can quickly change the Picture Mode without entering the

Picture Control menu screen.

1 Press the button on the remote control to directly access the

Picture Mode.

2 Push the joystick to $ or 4 to select your desired picture mode

(Personal, Movie or Live), then press the OK button to remove the

display from the screen.

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

PICTURE CONTROL

Personal

Wide

Picture Mode

Contrast

Reset

Format

PICTURE MODE

Personal

Picture Mode

Brightness

Colour

Sharpness

Hue

K

Personal

Movie

Live

La pagina sta caricando ...

Sony KP-41PZ1D Manuale utente

Sony KP-41PZ1D Manuale utente

in altre lingue

Documenti correlati

Altri documenti