Pioneer AVIC 8 DVD II Istruzioni per l'uso

ENG/MASTER COVER 98 INST

MANUEL D’INSTALLATION

INSTALLATION MANUAL

ENGLISH

ESPAÑOL

DEUTSCH

FRANÇAIS

ITALIANO

NEDERLANDS

This product conforms to new cord colours.

Los colores de los cables de este producto se confor-

man con un nuevo código de colores.

Dieses Produkt entspricht den neuen kabelfarben.

Le code de couleur des câbles utilisé pour ce produit est

nouveau.

Questo prodotto è conforme ai nuovi codici colori.

De kleuren van de snoeren van dit toestel zijn gewijzigd.

3

AVIC-9DVD—

AVIC-8DVD—

CRD3647A_inst_cover 4/15/02 2:11 PM Page 3

1

IMPORTANT INFORMATION

ABOUT YOUR NEW DVD NAVIGATION UNIT AND THIS MANUAL

• The Pioneer DVD Navigation Unit is intended solely as an aid to you in the oper-

ation of your vehicle. It is not a substitute for your attentiveness, judgement and

care while driving.

• Do not use your navigation system to route you to emergency services such as

hospitals or police stations. Not all emergency service facilities are contained in

the map data.

• Do not operate the DVD Navigation Unit if doing so will divert your attention

from the safe operation of your vehicle. Always observe safe driving rules and

follow all existing traffic regulations.

• This manual explains how to install this DVD Navigation Unit in your vehicle.

Operation of this DVD Navigation Unit is explained in the separate “Operation

Manual” that also came with this unit.

ENG/MASTER 96

2

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 2

3

IMPORTANT SAFEGUARDS .................... 3

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR DVD NAVIGATION

UNIT AND RETAIN THEM

FOR FUTURE REFERENCE .................... 3

Connecting the System ............................ 4

CAUTION ........................................................ 4

-

Before installing the unit

-

To prevent damage

-

Parts supplied

Connecting the system ...................................... 6

-

Connecting to the display with 20-pin

RGB input (AVIC-8DVD2)

-

Connecting to the display with 26-pin

RGB input

(AVH-P6400CD, AVH-P6400R, etc.)

-

Connecting to the display with 20-pin

RGB input (AVIC-9DVD2)

Connecting the power cord (1) .......................... 9

Connecting the power cord (2) ........................ 11

Installation ................................................ 12

CAUTION ...................................................... 12

To guard against electromagnetic

interference ................................................13

Before installing and fixing ............................ 13

Before using the adhesive tape ........................ 13

Installing the main unit .................................... 14

-

Installation notes

-

Parts supplied

-

CAUTION

-

If you install with the left and right sides of

the DVD Navigation Unit parallel to your

vehicle’s forward / backward direction

DIN Front/Rear-mount .................................... 17

DIN Front-mount ............................................ 17

-

Installation with the rubber bush

-

Removing the Unit

DIN Rear-mount .............................................. 18

-

Installation using the screw holes on the

side of the unit

Installing the GPS aerial .................................. 19

-

CAUTION

-

Installation notes

-

Parts supplied

-

When installing the aerial inside the

vehicle (on the dashboard or rear shelf)

-

When installing the aerial outside the

vehicle (on the body)

Installing the Remote control .......................... 22

-

Parts supplied

-

Loading the batteries

-

CAUTION

-

Remote control handling notes

-

When Installing with double-sided tape

Installing the microphone ................................ 24

-

Installation notes

-

Parts supplied

-

When installing the microphone on the

sun visor

-

When installing the microphone on the

steering column

-

CAUTION

After installing the unit .......................... 27

2

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

Contents

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 3

4

ENG/MASTER 96

IMPORTANT SAFEGUARDS

3

PLEASE READ ALL OF THESE INSTRUCTIONS REGARDING YOUR DVD

NAVIGATION UNIT AND RETAIN THEM FOR FUTURE REFERENCE

1. Read this manual fully and carefully before installing your DVD Navigation Unit.

2. Keep this manual handy for future reference.

3. Pay close attention to all warnings in this manual and follow the instructions care-

fully.

4. This unit is intended solely as an aid to you in the operation of your vehicle. It is

not a substitute for your attentiveness, judgement and care while driving. Do not

operate your DVD Navigation Unit if doing so will divert your attention from the

safe operation of your vehicle. Always observe safe driving rules and follow all

existing traffic regulations.

5. This DVD Navigation Unit may in certain circumstances display erroneous infor-

mation regarding the position of your vehicle, the distance of objects shown on

the screen, and compass directions. In addition, the system has certain limitations,

including the inability to identify one-way streets, temporary traffic restrictions

and potentially unsafe driving areas. Please exercise your own judgement in light

of actual driving conditions.

6. As with any accessory in your vehicle’s interior, the DVD Navigation Unit

should not divert your attention from the safe operation of your vehicle. If you

experience difficulty in operating the system or reading the display, please make

adjustments while safely parked.

7. Do not attempt to install or service your DVD Navigation Unit by yourself.

Installation or servicing of the DVD Navigation Unit by persons without training

and experience in electronic equipment and automotive accessories may be dan-

gerous and could expose you to the risk of electric shock or other hazards.

8. Please remember to wear your seat belt at all times while operating your vehicle.

If you are ever in an accident, your injuries can be considerably more severe if

your seat belt is not properly fastened.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 4

5

4

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

Connecting the System

CAUTION

• Pioneer does not recommend that you install or service your DVD navigation

unit yourself. Installing or servicing of the product may expose you to risk of

electric shock or other hazards. Refer all installation and servicing of your

navigation unit to authorised Pioneer service personnel.

• Secure all wiring with cable clamps or electrical tape. Do not allow any bare

wiring to remain exposed.

• Do not drill a hole into the engine compartment to connect the yellow lead of

the unit to the vehicle battery. Engine vibration may eventually cause the

insulation to fail at the point where the wire passes from the passenger com-

partment into the engine compartment. Take extra care in securing the wire

at this point.

• It is extremely dangerous to allow the GPS aerial cable or microphone cable

to become wound around the steering column or gearstick. Be sure to install

the unit in such a way that it will not obstruct driving.

• Make sure that wires will not interfere with moving parts of the vehicle, such

as the gearstick, handbrake or seat sliding mechanism.

• Do not route wires where they will be exposed to high temperatures. If the

insulation heats up, wires may become damaged, resulting in a short circuit

or malfunction.

• Do not cut the GPS aerial cable to shorten it or use an extension to make it

longer. Altering the aerial cable could result in a short circuit or malfunc-

tion.

• Do not shorten any leads. If you do, the protection circuit may fail to work

properly.

• Never feed power to other electronic products by cutting the insulation of the

power supply lead of the DVD navigation unit and tapping into the lead. The

current capacity of the lead will be exceeded, causing overheating.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 5

5

Connecting the System

Before installing the unit

• This unit is for vehicles with a 12-volt battery and negative grounding. Before installing

it in a recreational vehicle, lorry, or bus, check the battery voltage.

To prevent damage

Parts supplied

26-pin RGB cable

(AVIC-9DVD2 only)

Inter connector

(AVIC-8DVD2 only)

ConnectorPower cord

No ACC positionACC position

O

N

S

T

A

R

T

O

F

A

C

O

N

S

T

A

R

T

O

F

• When disconnecting a connector, pull

the connector itself. Do not pull the

lead, as you may pull it out of the con-

nector.

• If this unit is installed in a vehicle that

does not have an ACC (accessory)

position on the ignition switch, the red

lead of the unit should be connected to

a terminal coupled with ignition switch

ON/OFF operations. If this is not done,

the vehicle battery may be drained

when you are away from the vehicle

for several hours.

• To avoid short-circuiting, cover the

disconnected lead with insulating tape.

• To avoid shorts in the electrical sys-

tem, be sure to disconnect the (-) bat-

tery cable before beginning installa-

tion.

ENG/MASTER 96

6

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 6

7

6

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

Connecting the system

Connecting to the display with 20-pin RGB input (AVIC-8DVD

22

)

15 cm

1 m

6 m

5 m

This product

Power cord

☞

See pages 9-11.

RGB input

Hide-away Unit

(supplied with the Display)

RGB cable (supplied with the Display)

To Display Unit

(ex. AVD-W6010)

Inter Connector (supplied) Microphone

☞

See pages 24.

GPS aerial

☞

See pages 19.

Antenna jack

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 7

8

7

Connecting the System

ENG/MASTER 96

Microphone

Connecting to the display with 26-pin RGB input (AVH-P6400CD, AVH-P6400R, etc.)

Power cord

This product

☞

See pages 9-11.

Antenna jack

15 cm

Note:

If you use equipment other than this unit

that require the connection of FM aerial,

use an adequate aerial distributor available

in the shops.

GPS aerial

☞

See page 19.

☞

See page 24.

(Ex. AVH-P6400CD, AVH-P6400R)

AVIC-9DVD2: supplied

AVIC-8DVD2: CD-RGB600 (sold separately)

* Not used the Inter connector cable which supplied with

the AVIC-8DVD2.

When resetting AV Head Unit

When pressing the reset button of AV Head

Unit while Navigation System and AV Head

Unit (AVH-P6400CD, AVH-P6400R) are

combined, make sure that ACC is tuned

OFF. If the reset button is pressed while

ACC is ON, it may not work properly.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 8

Connecting to the display with 20-pin RGB input (AVIC-9DVD

22

)

8

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

9

Please make sure to com-

plete this connection.

Otherwise you cannot see

the image of the DVD-

Video.

Audio output

Video output

Microphone

☞

See page 24.

GPS aerial

☞

See page 19.

RCA cable

(sold separately)

CD-RGB26P

(sold separately)

RGB output (Green)

Use this jack when

connecting the

Pioneer display.

Green

Power cord

This product

☞

See pages 9-11.

Level Control

This is used for adjusting output from Audio

Output. If you turn it to the right, the volume

increases, while turning it to the left reduces the

volume. (Normally, turn it fully to the right, and

instead use the external equipment outputting

sound, such as a display, for adjusting the vol-

ume.)

Antenna jack

15 cm

Note:

If you use equipment other than this unit

that require the connection of FM aerial,

use an adequate aerial distributor available

in the shops.

To RGB input of the

display.

To Audio inputs.

To VTR input of the

display.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 9

10

9

Connecting the System

ENG/MASTER 96

Connecting the power cord (1)

Speed detection circuit lead

Vehicle injection computer

Connection method

Connector

Pass the extension cord and

the lead for the speed detec-

tion circuit through this hole.

Clamp firmly with

needle-nosed pliers.

Close the cover.

Note: The position of the speed

detection circuit depends on the

vehicle model. For details, consult

the relevant documents from

Pioneer. When making connec-

tions for a model not listed in

those documents or for which con-

nection to the speed detection cir-

cuit is too difficult, connect the

separately sold ND-PG1 speed

pulse generator to the pink lead.

Note: The position of the hand-

brake switch depends on the vehi-

cle model. For details, consult the

vehicle owner’s manual or dealer.

Pink (CAR SPEED SIGNAL INPUT)

The mobile navigation system is connected here to detect the distance

the vehicle travels. Always connect the vehicle’s speed detection cir-

cuit or the ND-PG1 speed pulse generator, sold separately. Failure to

make this connection will increase errors in the location display.

WARNING: IMPROPER CONNECTION MAY RESULT IN

SERIOUS DAMAGE OR INJURY INCLUDING ELECRICAL

SHOCK, AND INTERFERENCE WITH THE OPERATION OF

THE VEHICLE’S ANTILOCK BRAKING SYSTEM, AUTO-

MATIC TRANSMISSION AND SPEEDMETER INDICATION.

Lightgreen

Used to detect the ON/OFF status of the handbrake. This lead must

be connected to the power supply side of the handbrake switch. If

this connection is made incorrectly or omitted, certain functions

of your navigation system will be unusable.

Connection method

Clamp the handbrake switch

power supply side lead.

Clamp firmly with

needle-nosed pliers.

Power supply side

Ground side

Handbrake switch

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 10

11

10

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

Note:

Cords for this product and those for other

products may be different colours even if

they have the same function. When con-

necting this product to another product,

refer to the supplied Installation manuals of

both products and connect cords that have

the same function.

This product

Power cord

Black, Orange/white, Red, Yellow

☞

See Page 11.

Yellow/black

When combining this navigation unit with a Pioneer car stereo,

if the car stereo has yellow/black leads, connect them to those

leads. In this way, when the guidance audio is output and

when you operate the system by voice, the vehicle stereo is

automatically muted to reduce the vehicle stereo volume.

Purple/white (REVERSEGEAR SIGNAL INPUT)

This is connected so that the navigation system can

detect whether the vehicle is moving forwards or

backwards. Connect the purple/white lead to the

lead whose voltage changes when the reverse gear

is engaged. Unless connected, the sensor may not

detect your vehicle travelling forward/backward

properly, and thus the position of your vehicle

detected by the sensor may be misaligned from the

actual position.

Note: When you use the ND-PG1 speed pulse

generator (sold separately), please make sure

to connect it.

Connection method

Clamp the reversing lamp

lead.

Clamp firmly with

needle-nosed pliers.

Reversing lamp lead.

Fuse resistor

Check the position of your vehicle’s

reversing lamp (the one that lights up

when the gearstick is in reverse [R]) and

find the reversing lamp lead in the boot.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 11

12

11

Connecting the System

ENG/MASTER 96

Connecting the power cord (2)

This product

Yellow

To the terminal always supplied with power regardless of

ignition switch position.

Fuse holder (7.5 A)

Red

To the electric terminal controlled by the ignition switch

(12 V DC) ON/OFF.

Do not connect this lead to power source terminals to

which power is continuously supplied. If the lead is

connected to such terminals, the battery may be drained.

Orange/white

To lighting switch terminal.

Black

To vehicle (metal) body. To keep electromagnetic noise

from the vehicle body out of the mobile navigation system,

attach this lead near the main unit.

Fuse resistor

Yellow/black, Purple/white,

Pink,

Lightgreen

Note: When replacing the fuse, be

sure to use only a fuse of the rating

prescribed on the fuse holder.

Power cord

See

pages 9-11.

Note: The yellow, red, and orange/white leads should

be connected to the opposite side of the fusebox

terminals from the battery.

☞

Note:

Cords for this product and those for other products

may be different colours even if they have the same

function. When connecting this product to another

product, refer to the supplied Installation manuals

of both products and connect cords that have the

same function.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 12

13

Installation

12

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

CAUTION

• Pioneer does not recommend that you install or service your DVD navigation

unit yourself. Installing or servicing the product may expose you to risk of

electric shock or other hazards. Refer all installation and servicing of your

navigation unit to authorised Pioneer service personnel.

• Never install the unit in places where:

* It could injure the driver or passengers if the vehicle stops suddenly.

* It may interfere with the driver’s operation of the vehicle, such as on the

floor in front of the driver’s seat.

• Make sure there is nothing behind the dashboard or panelling when drilling

holes in them. Be careful not to damage fuel lines, brake lines or power

cables.

• When using screws, do not allow them to come into contact with any electri-

cal lead. Vibration may damage wires, leading to a short circuit or other

damage to the vehicle.

• To ensure proper installation, use the supplied parts in the manner specified.

If any parts other than the supplied ones are used, they may damage internal

parts of the unit or they may work loose and the unit may become detached.

• It is extremely dangerous to allow the GPS aerial lead or microphone lead to

become wound around the steering column or gearstick. Be sure to install

the unit in such a way that it will not obstruct driving.

• Make sure that leads cannot get caught in a door or the sliding mechanism of

a seat, resulting in a short circuit.

• Please confirm the proper function of your vehicle’s other equipment follow-

ing installation of the DVD navigation unit.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 13

14

To guard against electromagnetic interference

• In order to prevent interference, set the following items as far as possible from the main

unit of this Navigation System, other cables or leads:

- TV aerial and aerial lead

- FM, MW/LW aerial and its lead

- GPS aerial and its lead

In addition you should lay each aerial lead as far as possible from other aerial leads.

Do not bind them together, lay them together, or cross them.

Such electromagnetic noise would increase the error for the location display.

Before installing and fixing

• Consult with your nearest dealer if installation requires the drilling of holes or other mod-

ifications of the vehicle.

•Before finally installing the unit, connect the wiring temporarily, making sure it is all

connected up properly, and the unit and the system work properly.

Before using the adhesive tape

• Make sure the surface is free of moisture, dust, grime, oil, etc. before affixing the tape.

13

Installation

ENG/MASTER 96

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 14

15

14

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

Installing the main unit

Installation notes

• Do not install the main unit in places where it may become subject to high temperatures

or humidity, such as:

* Places close to a heater outlet.

* Places exposed to direct sunlight, such as on top of the dashboard or the rear shelf.

* Places that may be splashed by rain, for example close to the door.

• The installation strength will depend on the vehicle model and the installation position.

Choose a position where the main unit can be firmly installed, and install it securely.

If the main unit is not securely fastened, the errors in location display will be greater.

• Do not install the main unit on the board covering the spare tyre or other places which

are subject to vibration.

• When the main unit is installed under a front seat, ensure that it does not obstruct the

sliding action of the seat.

• Do not install the main unit where it will be under luggage. Strong mechanical shock to

the main unit would increase the errors in location display.

• Avoid installing the main unit in places where it will interfere with loading and unload-

ing of the spare tyre, jack, tools, etc.

• Check that a disc or a PC card can be ejected with the main unit installed.

• Install the main unit on a surface within +30 degrees to -15 degrees tolerance (within

five degrees to the left or right of your vehicle’s direction of travel). A surface tilted

more than this would increase the errors in location display.

• Do not install the main unit vertically. Installing it this way can cause it to function

improperly.

5°

30°

15°

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 15

16

15

Installation

ENG/MASTER 96

Parts supplied

Holder

Extraction Key (2 pcs.)

Screw

Main unit

Rubber bush Binding screw

(5 × 6 mm)

(4 pcs.)

Flush surface screw

(5 × 6 mm)

(4 pcs.)

Frame

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 16

CAUTION

• Install with the left and right sides of the DVD Navigation Unit perpendicular

or parallel to your vehicle’s direction of travel. Do not install diagonally to your

vehicle’s direction of travel or the current location will be displayed incorrectly.

• If you install the left and right sides of the DVD Navigation Unit parallel to

your vehicle’s direction of travel, switch the installation direction lever, and

attach the locking screw to the “↔” side, or else the G sensor mounted in the

DVD Navigation Unit will not operate correctly.

If you install with the left and right sides of the DVD Navigation Unit parallel to

your vehicle’s forward / backward direction

If you install with the left and right sides of the DVD Navigation Unit parallel to your

vehicle’s forward / backward direction, remove the mounting screw underneath the DVD

Navigation Unit, and switch the installation direction lever. Then change the screw mount-

ing position from “

↔” side to “↕” side. If the screw is attached to the “↔” side, the G sen-

sor mounted in the DVD Navigation Unit will not operate correctly.

1. Remove the locking screw attached to the installation direction lever.

2. Switch the lever, and attach the mounting screw to the “↔” side.

Locking screw

Installation direction lever

Underneath the DVD Navigation Unit

Locking screw

Installation direction lever

Front

Front Front

Front

(Perpendicular)

Attachment

position of the

locking screw

↕

(Parallel)

Attachment

position of the

locking screw

↔

Forward / Backward

direction of vehicle

Forward / Backward

direction of vehicle

Forward / Backward

direction of vehicle

16

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

17

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 17

18

17

Installation

ENG/MASTER 96

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or

“Rear” (DIN Rear-mount installation, utilising threaded screw holes at the sides of unit

chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush

Removing the Unit

After inserting the holder into the dash-

board, then select the appropriate tabs

according to the thickness of the dash-

board material and bend them.

(Install as firmly as possible using the

top and bottom tabs. To secure, bend

the tabs 90 degrees.)

182

53

Rubber bush

Screw

Dashboard

Holder

Pull out to remove the frame.

(When reattaching the frame, point the

side with a groove downwards and

attach it.)

Frame

Insert the supplied extrac-

tion keys into the unit, as

shown in the figure, until

they click into place.

Keeping the keys pressed

against the sides of the unit,

pull the unit out.

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 18

DIN Rear-mount

Installation using the screw holes on the side of the unit

• Fastening the unit to the factory radio mounting bracket.

Select a position where the screw holes of the bracket and

the screw holes of the head unit become aligned (are fit-

ted), and tighten the screws at 2 places on each side.

Use either binding screws (5 × 6 mm) or flush surface

screws (5 × 6 mm), depending on the shape of the screw

holes in the bracket.

18

ENGLISH ESPAÑOL DEUTSCH FRANÇAIS

ITALIANO NEDERLANDS

ENG/MASTER 96

19

Screw

Dashboard or Console

Mounting bracket

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 19

19

Installation

Installing the GPS aerial

CAUTION

• Do not cut the GPS aerial lead to shorten it or use an extension to make it

longer. Altering the aerial cable could result in a short circuit.

Installation notes

• When installing the GPS aerial inside the vehicle, be sure to use the metal sheet provid-

ed with your system. If this is not used, the reception sensitivity will be poor.

• Do not cut the accessory metal sheet. This would reduce the sensitivity of the GPS aeri-

al.

• Take care not to pull the aerial lead when removing the GPS aerial. The magnet attached

to the aerial is very powerful, and the lead may become detached.

• The GPS aerial is installed with a magnet. When installing the GPS aerial, be careful

not to scratch the vehicle body.

• When installing the GPS aerial on the outside of the vehicle, always put it in the vehicle

when going through an automatic vehicle wash. If it is left on the outside it may be

knocked off and scratch the vehicle body.

• Do not paint the GPS aerial, as this may affect its performance.

Dashboard

Roof

Rear shelf

Boot lid

• The aerial should be installed on a

level surface where radio waves will

be blocked as little as possible. Radio

waves cannot be received by the aerial

if reception from the satellite is

blocked.

Installation on the vehicle roof or boot

lid is recommended to enable best

reception.

ENG/MASTER 96

20

CRD3647A_inst_001_029_UK 4/15/02 2:03 PM Page 20

La pagina sta caricando ...

Pioneer AVIC 8 DVD II Istruzioni per l'uso

Pioneer AVIC 8 DVD II Istruzioni per l'uso

in altre lingue

Documenti correlati