Sony CDX-S2050 Manuale utente

Categoria
Ricevitori multimediali per auto
Tipo
Manuale utente
Wichtig!
Bitte nehmen Sie sich etwas Zeit, um den Geräte-Pass vollständig
auszufüllen. Dieser befindet sich auf der hinteren Umschlagseite dieser
Bedienungsanleitung.
Si dichiara che l’apparecchio è stato fabbricato in conformità all’art. 2, Comma l del D.M. 28.08.
1995 n. 548.
For installation and connections, see the supplied installation/connections manual.
Zur Installation und zum Anschluss siehe die mitgelieferte Installations-/Anschlussanleitung.
En ce qui concerne l’installation et les connexions, consulter le manuel d’installation/
raccordement fourni.
Per l’installazione e i collegamenti, fare riferimento al manuale di istruzioni per
l’installazione e i collegamenti in dotazione.
Zie voor het monteren en aansluiten van het apparaat de bijgeleverde handleiding "Installatie
en aansluiting en".
CDX-S2050V CDX-S2050C
CDX-S2050
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
Operating Instructions
Bedienungsanleitung
Mode d’emploi
Istruzioni per l’uso
Gebruiksaanwijzing
2-348-403-21 (1)
© 2005 Sony Corporation
GB
DE
FR
IT
NL
H:\Data Disk\2348403211\234840321CDXS2050VEUR\00GB+00COV-EUR.fm masterpage:Right
FM
/
MW
/
LW
Compact Disc Player
2
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB01INT-EUR.fm masterpage:Left
Welcome !
Thank you for purchasing this Sony Compact
Disc Player. You can enjoy your drive with the
following functions.
CD playback:
You can play CD-DA and CD-R/CD-RW for
audio use.
Radio reception:
You can store up to 6 stations per band (FM1,
FM2, FM3, MW and LW).
BTM (Best Tuning Memory) function: the
unit selects strong signal stations and stores
them.
•RDS services:
You can use FM station with Radio Data
System (RDS).
Warning if your car’s ignition has no
ACC position
After turning the ignition off, be sure to press
and hold (OFF) on the unit until the display
disappears.
Otherwise, the display does not turn off and
this causes battery drain.
This label is located on the bottom of the
chassis.
3
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\00GB+00COV-EURTOC.fm masterpage:Right
Table of Contents
Getting Started
Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 4
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 4
DEMO mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Detaching the front panel . . . . . . . . . . . . . . . . . 4
Attaching the front panel . . . . . . . . . . . . . . . 5
Location of controls and basic
operations
Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Radio
Storing and receiving stations . . . . . . . . . . . . . . 7
Storing automatically — BTM . . . . . . . . . . . 7
Storing manually. . . . . . . . . . . . . . . . . . . . . . 7
Receiving the stored stations . . . . . . . . . . . . 7
Tuning automatically . . . . . . . . . . . . . . . . . . 7
RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting AF and TA/TP . . . . . . . . . . . . . . . . . 8
Selecting PTY. . . . . . . . . . . . . . . . . . . . . . . . 8
Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Other functions
Changing the sound settings. . . . . . . . . . . . . . . 9
Adjusting the sound characteristics
— BAL/FAD/SUB. . . . . . . . . . . . . . . . . . . . 9
Adjusting the equalizer curve — EQ3 . . . . . 9
Adjusting setup items — SET . . . . . . . . . . . . . 9
Using optional remote commanders. . . . . . . . 10
Card remote commander RM-X114. . . . . . 10
Rotary commander RM-X4S . . . . . . . . . . . 10
Additional Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Notes on discs . . . . . . . . . . . . . . . . . . . . . . 11
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Removing the unit. . . . . . . . . . . . . . . . . . . . . . 12
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 13
Error displays/Messages. . . . . . . . . . . . . . . 14
4
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Left
Getting Started
Resetting the unit
Before operating the unit for the first time, or
after replacing the car battery or changing the
connections, you must reset the unit.
Detach the front panel and press the RESET
button with a pointed object, such as a ballpoint
pen.
Note
Pressing the RESET button will erase the clock setting
and some stored contents.
Setting the clock
The clock uses a 24-hour digital indication.
1 Press and hold (SEL).
The setup display appears.
2 Press (SEL) repeatedly until “CLOCK-
ADJ” appears.
3 Press (DSPL ) .
The hour indication flashes.
4 Press the volume +/– button to set the
hour and minute.
To move the digital indication, press (DSPL).
5 Press (SEL).
The clock starts and the next setup display
appears.
6 Press and hold (SEL).
The setup is complete.
To display the clock, press (DSPL) . Press
(DSPL) again to return to the previous display.
Tip
You can set the clock automatically with the RDS
feature (
page 8).
With the card remote commander
In step 2 and 4, to select the item or setting, press M
or m. In step 4, to move the digital indication, press <
or ,.
DEMO mode
When the unit is turned off, the clock is
displayed first, then demonstration (DEMO)
mode starts the demonstration display.
To cancel the DEMO mode, set “DEMO-OFF
in setup (
page 9) while the unit is turned off.
Detaching the front panel
You can detach the front panel of this unit to
prevent theft.
Caution alarm
If you turn the ignition switch to the OFF
position without detaching the front panel, the
caution alarm will sound for a few seconds.
The alarm will only sound if the built-in
amplifier is used.
1 Press (OFF).
The unit is turned off.
2 Press , then pull it off towards you.
Notes
Do not drop or put excessive pressure on the front
panel and display window.
Do not subject the front panel to heat/high
temperature or moisture. Avoid leaving it in a parked
car or on a dashboard/rear tray.
Tip
When carrying the front panel, use the supplied front
panel case.
RESET
button
(OFF)
5
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:RightH:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Right
Attaching the front panel
Engage part A of the front panel with part B of
the unit, as illustrated, and push the left side into
position until it clicks.
Note
Do not put anything on the inner surface of the front
panel.
B
A
6
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Left
Location of controls and basic operations
Main unit
Refer to the pages listed for details.
a Volume +/– button
To adjust volume.
b SEL (select) button 4, 9
To select items.
c SOURCE button
To power on/change the source (Radio/CD).
d MODE button 7
To select the radio band (FM/MW/LW).
e Disc slot
Insert the disc (label side up), playback
starts.
f Display window
g ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
h EQ3 (equalizer) button 9
To select an equalizer curve (XPLOD,
VOCAL, CLUB, JAZZ, NEW
AGE, ROCK
and CUSTOM).
i Z (eject) button
To eject the disc.
j SEEK +/– button
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
CD:
To skip tracks (press); fast-forward/reverse a
track (press and hold).
k (front panel release) button 4
l DSPL (display)/DIM (dimmer) button
4, 7
To change display items (press); change the
display brightness (press and hold).
m SENS/BTM button 7
To improve weak reception: LOCAL/MONO
(press); start the BTM function (press and
hold).
n RESET button (located behind the front
panel) 4
o Number buttons
Radio:
To receive stored stations (press); store
stations (press and hold).
CD:
(3): REP
To play the current track/disc repeatedly.
(4): SHUF
To play the tracks in random order.
p PTY (Programme Type) button 8
To select PTY in RDS.
q AF (Alternative Frequencies)/TA
(Traffic Announcement) button
8
To set AF and TA/TP in RDS.
r OFF button
To power off/stop the source.
s Receptor for the card remote
commander
10
SEL
AF/TA
BTMDIM SHUFREP
EQ3ATT
SOURCE MODE
SEEK
CDX-S2050V
CDX-S2050C
CDX-S2050
SENS
PTY OFF
DSPL
123456
qlqa
1234 5 6 7890
qs qd qf qg qh qj qk
7
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:RightH:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Right
Radio
Storing and receiving
stations
Caution
When tuning in stations while driving, use Best
Tuning Memory (BTM) to prevent an accident.
Storing automatically — BTM
1 Press (SOURCE) repeatedly until
“TUNER” appears.
To change the band, press (MODE)
repeatedly. You can select from FM1, FM2,
FM3, MW or LW.
2 Press and hold (BTM) until “BTM”
flashes.
The unit stores stations in order of frequency
on the number buttons.
A beep sounds when the setting is stored.
Storing manually
1 While receiving the station that you
want to store, press and hold a
number button ((1) to (6)) until
“MEM” appears.
The number button indication appears in the
display.
Note
If you try to store another station on the same number
button, the previous stored station will be replaced.
Tip
When an RDS station is stored, the AF/TA setting is
also stored (
page 8).
Receiving the stored stations
1 Select the band, then press a number
button ((1) to (6)).
With the card remote commander
To select preset stations, press M or m.
Tuning automatically
1 Select the band, then press (SEEK) +/–
to search for the station.
Scanning stops when the unit receives a
station. Repeat this procedure until the
desired station is received.
Tip
If you know the frequency of the station you want to
listen to, press and hold (SEEK)
+/ to locate the
approximate frequency, then press (SEEK)
+/
repeatedly to fine adjust to the desired frequency
(manual tuning).
RDS
Overview
FM stations with Radio Data System (RDS)
service send inaudible digital information along
with the regular radio programme signal.
Display items
A Radio band, Function
B Frequency*
1
(Station name), Clock,
RDS data
C TA/TP*
2
*1 While receiving the RDS station, “ *” is displayed
on the left of the frequency indication.
*2 “TA” flashes during traffic information. “TP” lights
up while such a station is received.
To change display items B, press (DSPL).
RDS services
This unit automatically provides RDS services as
follows:
AF (Alternative
Frequencies)
Selects and retunes the
station with the strongest
signal in a network. By
using this function, you can
continuously listen to the
same programme during a
long-distance drive without
having to retune the same
station manually.
TA (Traffic
Announcement)/
TP (Traffic
Programme)
Provides current traffic
information/programmes.
Any information/
programme received, will
interrupt the currently
selected source.
PTY (Programme
Types)
Displays the currently
received programme type.
Also searches your selected
programme type.
CT (Clock Time) The CT data from the RDS
transmission sets the clock.
continue to next page t
ABC
8
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Left
Notes
Depending on the country/region, not all RDS
functions may be available.
RDS will not work if the signal strength is too weak,
or if the station you are tuned to is not transmitting
RDS data.
Setting AF and TA/TP
1 Press (AF/TA) repeatedly until the
desired setting appears.
Storing RDS stations with the AF and
TA setting
You can preset RDS stations along with the AF/
TA setting. If you use the BTM function, only
RDS stations are stored with the same AF/TA
setting.
If you preset manually, you can preset both RDS
and non-RDS stations with the AF/TA setting for
each.
1 Set AF/TA, then store the station with BTM or
manually.
Presetting the volume of traffic
announcements
You can preset the volume level of the traffic
announcements so as to not miss hearing them.
1 Press the volume +/– button repeatedly to
adjust the volume level.
2 Press and hold (AF/TA) until “TA” appears.
Receiving emergency
announcements
With AF or TA on, the emergency
announcements will automatically interrupt the
currently selected source.
Staying with one regional
programme — REG
When the AF function is on: this unit’s factory
setting restricts reception to a specific region, so
you will not be switched to another regional
station with a stronger frequency.
If you leave this regional programme’s reception
area, set “REG-OFF” in setup (
page 9).
Note
This function does not work in the UK and in some
other areas.
Local Link function (UK only)
This function enables you to select other local
stations in the area, even if they are not stored on
your number buttons.
1 During FM reception, press a number button
((1) to (6)) on which a local station is stored.
2 Within 5 seconds, press again a number button
of the local station.
Repeat this procedure until the local station is
received.
Selecting PTY
1 Press (PTY) during FM reception.
The current programme type name appears if
the station is transmitting PTY data.
2 Press (PTY) repeatedly until the
desired programme type appears.
3 Press (SEEK) +/–.
The unit starts to search for a station
broadcasting the selected programme type.
With the card remote commander
In step 2, to select the programme type, press M or m.
Type of programmes
Note
You cannot use this function in countries/regions
where no PTY data is available.
Setting CT
1 Set “CT-ON” in setup (page 9).
Notes
The CT function may not work even though an RDS
station is being received.
There might be a difference between the time set by
the CT function and the actual time.
Select To
AF-ON activate AF and deactivate TA.
TA-ON activate TA and deactivate AF.
AF, TA-ON activate both AF and TA.
AF, TA-OFF deactivate both AF and TA.
NEWS (News), AFFAIRS (Current Affairs),
INFO (Information), SPORT (Sports),
EDUCATE (Education), DRAMA (Drama),
CULTURE (Culture), SCIENCE (Science),
VARIED (Varied), POP
M (Popular Music),
ROCK
M (Rock Music), EASY M (Easy
Listening), LIGHT
M (Light Classical),
CLASSICS (Classical), OTHER
M (Other
Music Type), WEATHER (Weather),
FINANCE (Finance), CHILDREN (Children’s
Programmes), SOCIAL
A (Social Affairs),
RELIGION (Religion), PHONE
IN (Phone In),
TRAVEL (Travel), LEISURE (Leisure), JAZZ
(Jazz Music), COUNTRY (Country Music),
NATION
M (National Music), OLDIES (Oldies
Music), FOLK
M (Folk Music), DOCUMENT
(Documentary)
9
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:RightH:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Right
Other functions
Changing the sound
settings
Adjusting the sound
characteristics — BAL/FAD/SUB
You can adjust the balance, fader, and subwoofer
volume.
1 Press (SEL) repeatedly until “BAL,
“FAD” or “SUB” appears.
The item changes as follows:
LOW*
1
t MID*
1
t HI*
1
t
BAL (left-right) t FAD (front-rear) t
SUB (subwoofer volume)*
2
*1 When EQ3 is activated (page 9).
*2 When the audio output is set to “SUB” (page 9).
“ATT” is displayed at the lowest setting, and can
be adjusted up to 20 steps.
2 Press the volume +/– button
repeatedly to adjust the selected item.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
Note
Adjust within 3 seconds of selecting the item.
With the card remote commander
In step 2, to adjust the selected item, press < or ,.
Adjusting the equalizer curve
— EQ3
You can adjust and store the equalizer settings
for different tone ranges.
1 Select a source, then press (EQ3)
repeatedly to select the EQ3 mode.
2 Press (SEL) repeatedly until “LOW,
“MID” or “HI” appears.
3 Press the volume +/– button
repeatedly to adjust the selected item.
The volume level is adjustable in 1 dB steps,
from –10 dB to +10 dB.
Repeat steps 2 and 3 to adjust the equalizer
curve.
To restore the factory-set equalizer curve,
press and hold (SEL) before the setting is
complete.
After 3 seconds, the setting is complete and
the display returns to normal play/reception
mode.
With the card remote commander
In step 3, to adjust the selected item, press < or ,.
Adjusting setup items
— SET
1 Press and hold (SEL) .
The setup display appears.
2 Press (SEL) repeatedly until the
desired item appears.
3 Press the volume +/– button to select
the setting (example “ON” or “OFF”).
4 Press and hold (SEL) .
The setup is complete and the display returns
to normal play/reception mode.
Note
Displayed items will differ, depending on the source
and setting.
With the card remote commander
In step 2, to select the setup item, press M or m. In
step 3, to select the setting, press < or ,.
The following items can be set (follow the page
reference for details):
z” indicates the default settings.
CLOCK-ADJ
(Clock Adjust)
(page 4)
CT (Clock
Time)
To set “CT-ON” or “CT-OFF
(z) (page 7, 8).
BEEP To set “BEEP-ON” (
z) or
“BEEP-OFF.
REAR/SUB*
1
To switch the audio output.
“REAR”: to output to a
power amplifier.
–“SUB (
z): to output to a
subwoofer.
DIM (Dimmer) To change the brightness of the
display.
–“DIM-ON: to dim the
display.
“DIM-OFF” (
z): to
deactivate the dimmer.
ILM-1/ILM-2
(Illumination)
(CDX-S2050C
only)
To change the illumination
colour.
“ILM-1” (
z): Amber
“ILM-2”: Green
DEMO*
1
(Demonstration)
To set “DEMO-ON” (
z) or
“DEMO-OFF” (page 4).
REG*
2
(Regional)
To setREG-ON (z) or
“REG-OFF” (page 8).
continue to next page t
10
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Left
*1 When the unit is turned off.
*2 When FM is received.
*3 When the audio output is set to “SUB.
Using optional remote
commanders
Card remote commander
RM-X114
Location of controls
The corresponding buttons on the card remote
commander control the same functions as those
on this unit.
The following buttons on the card remote
commander have also different buttons/functions
from the unit.
</, (SEEK –/+) buttons
To control radio/CD, the same as (SEEK) +/–
on the unit. (For details of other operations, see
“With the card remote commander” on each
pages.)
SOUND button
The same as (SEL) on the unit.
M/m (DISC*/PRESET +/–) buttons
For details, see “With the card remote
commander” on each pages.
* Not available for this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Replacing the lithium battery
Under normal conditions, the battery will last
approximately 1 year. (The service life may be
shorter, depending on the conditions of use.)
When the battery becomes weak, the range of the
card remote commander becomes shorter.
Replace the battery with a new CR2025 lithium
battery. Use of any other battery may present a
risk of fire or explosion.
Notes on the lithium battery
Keep the lithium battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
Wipe the battery with a dry cloth to assure a good
contact.
Be sure to observe the correct polarity when
installing the battery.
Do not hold the battery with metallic tweezers,
otherwise a short-circuit may occur.
Rotary commander RM-X4S
Attaching the label
Attach the indication label depending on how
you mount the rotary commander.
LPF*
3
(Low
Pass Filter)
To select the cut-off frequency
“78HZ,” “125HZ” or “OFF”
(
z).
DISC
ATTOFF
DSPL MODE
SOURCE
DISC
+
VOL
+
PRESET
+
SEEK
+
SEEK
PRESET –
SOUND
E
N
T
E
R
MENU
LIST
MODE
LIST
*
ENTER
*
ATT
DSPL
MENU
*
SOURCE
</,
(SEEK –/+ )
SOUND
OFF
VOL (+/ –)
m/M
(DISC
*
/
PRESET
+/ –)
x
+ side up
WARNING
Battery may explode if mistreated.
Do not recharge, disassemble, or dispose of
in fire.
S
E
L
DSPL
MODE
S
E
L
D
S
P
L
M
O
D
E
11
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:RightH:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Right
Location of controls
The corresponding buttons on the rotary
commander control the same functions as those
on this unit.
The following controls on the rotary commander
require a different operation from the unit.
PRESET control
To select preset stations (push in and rotate).
VOL control
The same as the volume +/– button on the unit
(rotate).
SEEK/AMS control
The same as (SEEK) +/– on the unit (rotate, or
rotate and hold).
Changing the operative direction
The operative direction of the controls is factory-
set as shown below.
If you need to mount the rotary commander on
the right hand side of the steering column, you
can reverse the operative direction.
1 While pushing the VOL control, press and
hold ( SEL ).
Additional Information
Precautions
If your car has been parked in direct sunlight,
allow the unit to cool off before operating it.
Power aerial will extend automatically while
the unit is operating.
Moisture condensation
On a rainy day or in a very damp area, moisture
condensation may occur inside the lenses and
display of the unit. Should this occur, the unit
will not operate properly. In such a case, remove
the disc and wait for about an hour until the
moisture has evaporated.
To maintain high sound quality
Be careful not to splash juice or other soft drinks
onto the unit or discs.
Notes on discs
To keep a disc clean, do not touch its surface.
Handle the disc by its edge.
Keep your discs in their cases or disc
magazines when not in use.
Do not subject discs to heat/high temperature.
Avoid leaving them in a parked car or on a
dashboard/rear tray.
Do not attach labels, or use discs with sticky
ink/residue. Such discs may stop spinning
when used, causing a malfunction, or may ruin
the disc.
Do not use any discs with labels or stickers
attached.
The following malfunctions may result from
using such discs:
Inability to eject a disc (due to a label or
sticker peeling off and jamming the eject
mechanism).
Inability to read audio data correctly (e.g.,
playback skipping, or no playback) due to
heat shrinking of a sticker or label causing a
disc to warp.
Discs with non-standard shapes (e.g., heart,
square, star) cannot be played on this unit.
Attempting to do so may damage the unit. Do
not use such discs.
You cannot play 8 cm CDs.
OFF
ATT
SEL
SOURCE
DSPL
MODE
OFF
VOL
SEEK/AMS
PRESET
To increase
To decrease
continue to next page t
12
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Left
Before playing, clean the
discs with a commercially
available cleaning cloth. Wipe
each disc from the centre out.
Do not use solvents such as
benzine, thinner,
commercially available
cleaners, or antistatic spray
intended for analogue discs.
Notes on CD-R/CD-RW discs
Some CD-Rs/CD-RWs (depending on the
equipment used for its recording or the
condition of the disc) may not play on this unit.
You cannot play a CD-R/a CD-RW that is not
finalized.
If you have any questions or problems
concerning your unit that are not covered in this
manual, consult your nearest Sony dealer.
Maintenance
Fuse replacement
When replacing the fuse, be
sure to use one matching the
amperage rating stated on the
original fuse. If the fuse
blows, check the power
connection and replace the
fuse. If the fuse blows again
after replacement, there may
be an internal malfunction. In
such a case, consult your
nearest Sony dealer.
Cleaning the connectors
The unit may not function properly if the
connectors between the unit and the front panel
are not clean. In order to prevent this, detach the
front panel (page 4) and clean the connectors
with a cotton swab dipped in alcohol. Do not
apply too much force. Otherwise, the connectors
may be damaged.
Notes
For safety, turn off the ignition before cleaning the
connectors, and remove the key from the ignition
switch.
Never touch the connectors directly with your fingers
or with any metal device.
Removing the unit
1 Remove the protection collar.
1Detach the front panel (page 4).
2Engage the release keys together with the
protection collar.
3Pull out the release keys to remove the
protection collar.
2 Remove the unit.
1Insert both release keys simultaneously
until they click.
2Pull the release keys to unseat the unit.
3Slide the unit out of the mounting.
Fuse (10A)
Main unit
Back of the front panel
Orient the release
keys as shown.
Hook facing
inwards.
13
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:RightH:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Right
Specifications
CD Player section
Signal-to-noise ratio: 120 dB
Frequency response: 10 – 20,000 Hz
Wow and flutter: Below measurable limit
Tuner section
FM
Tuning range: 87.5 – 108.0 MHz
Aerial terminal: External aerial connector
Intermediate frequency: 10.7 MHz/450 kHz
Usable sensitivity: 9 dBf
Selectivity: 75 dB at 400 kHz
Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz: 0.5 % (stereo),
0.3 % (mono)
Separation: 35 dB at 1 kHz
Frequency response: 30 – 15,000 Hz
MW/LW
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Aerial terminal: External aerial connector
Intermediate frequency: 10.7 MHz/450 kHz
Sensitivity: MW: 30 µV, LW: 40 µV
Power amplifier section
Outputs: Speaker outputs (sure seal connectors)
Speaker impedance: 4 – 8 ohms
Maximum power output: 50 W × 4 (at 4 ohms)
General
Outputs:
Audio outputs terminal (rear/sub switchable)
Power aerial relay control terminal
Power amplifier control terminal
Inputs:
Telephone ATT control terminal
Remote controller input terminal
Aerial input terminal
Tone controls:
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements: 12 V DC car battery
(negative earth)
Dimensions: Approx. 178 × 50 × 178 mm (w/h/d)
Mounting dimensions: Approx. 182 × 53 × 161 mm
(w/h/d)
Mass: Approx. 1.2 kg
Supplied accessories:
Parts for installation and connections (1 set)
Front panel case (1)
Optional accessories:
Card remote commander: RM-X114
Rotary commander: RM-X4S
Design and specifications are subject to change
without notice.
Troubleshooting
The following checklist will help you remedy
problems you may encounter with your unit.
Before going through the checklist below, check
the connection and operating procedures.
General
No power is being supplied to the unit.
Check the connection. If everything is in order,
check the fuse.
If the unit is turned off and the display
disappears, it cannot be operated with the
remote commander.
t Turn on the unit.
The power aerial does not extend.
The power aerial does not have a relay box.
No sound.
The volume is too low.
The ATT function is activated, or the Telephone
ATT function (when the interface cable of a car
telephone is connected to the ATT lead) is
activated.
The position of the fader control (FAD) is not
set for a 2-speaker system.
No beep sound.
The beep sound is cancelled (page 9).
An optional power amplifier is connected and
you are not using the built-in amplifier.
The contents of the memory have been
erased.
The RESET button has been pressed.
t Store again into the memory.
The power connecting lead or battery has been
disconnected.
The power connecting lead is not connected
properly.
Stored stations and correct time are erased.
The fuse has blown.
Makes noise when the position of the
ignition key is switched.
The leads are not matched correctly with the
car’s accessory power connector.
continue to next page t
Lead-free solder is used for soldering certain
parts.
(more than 80 %)
Halogenated flame retardants are not used in the
certain printed wiring boards.
Halogenated flame retardants are not used in
cabinets.
Packaging cushions do not use polystyrene foam.
14
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Left
Error displays/Messages
If these solutions do not help improve the
situation, consult your nearest Sony dealer.
If you take the unit to be repaired because of CD
playback trouble, bring the disc that was used at
the time the problem began.
The display disappears from/does not
appear in the display window.
The dimmer is set “DIM-ON”(page 9).
The display disappears if you press and hold
(OFF).
t Press and hold (OFF) again until the
display appears.
The connectors are dirty (page 12).
CD playback
The disc cannot be loaded.
Another disc is already loaded.
The disc has been forcibly inserted upside
down or in the wrong way.
The disc does not playback.
Defective or dirty disc.
The CD-Rs/CD-RWs are not for audio use
(page 12).
The sound skips.
Installation is not correct.
t Install the unit at an angle of less than
45° in a sturdy part of the car.
Defective or dirty disc.
The operation buttons do not function.
The disc will not eject.
Press the RESET button (page 4).
Radio reception
The stations cannot be received.
The sound is hampered by noises.
Connect a power aerial control lead (blue) or
accessory power supply lead (red) to the power
supply lead of a car’s aerial booster (only when
your car has built-in FM/MW/LW aerial in the
rear/side glass).
Check the connection of the car aerial.
The auto aerial will not go up.
t Check the connection of the power aerial
control lead.
Check the frequency.
Preset tuning is not possible.
Store the correct frequency in the memory.
The broadcast signal is too weak.
Automatic tuning is not possible.
Setting of the local seek mode is not correct.
t Tuning stops too frequently:
Press (SENS) until “LOCAL-ON” appears.
t Tuning does not stop at a station:
Press (SENS) repeatedly until “MONO-
ON” or “MONO-OFF” (FM), or “LOCAL-
OFF” (MW/LW) appears.
The broadcast signal is too weak.
t Perform manual tuning.
During FM reception, the “ST” indication
flashes.
Tune in the frequency accurately.
The broadcast signal is too weak.
t Press (SENS) to set the monaural reception
mode to “MONO-ON.
An FM programme broadcast in stereo is
heard in monaural.
The unit is in monaural reception mode.
t Press (SENS) until “MONO-OFF” appears.
RDS
The SEEK starts after a few seconds of
listening.
The station is non-TP or has weak signal.
t Deactivate TA (page 8).
No traffic announcements.
Activate TA (page 8).
The station does not broadcast any traffic
announcements despite being TP.
t Tune in another station.
PTY displays “- - - - - - - -.
The current station is not an RDS station.
RDS data has not been received.
The station does not specify the programme
type.
Error displays
The following indications will flash for about 5
seconds, and an alarm sound will be heard.
ERROR
The disc is dirty or inserted upside down.
t Clean or insert the disc correctly.
The disc cannot play because of some problem.
t Insert another disc.
FAILURE
The speaker/amplifier connection is incorrect.
t See the supplied installation/connections
manual to check the connection.
OFFSET
There may be an internal malfunction.
t Check the connection. If the error indication
remains on in the display, consult your
nearest Sony dealer.
RESET
The unit cannot be operated because of some
problem.
t Press the RESET button (page 4).
15
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:RightH:\Data Disk\2348403211\234840321CDXS2050VEUR\01GB02CD-EUR.fm masterpage:Right
Messages
L.SEEK +/–
The local seek mode is on during automatic
tuning.
NO AF
There is no alternative frequency for the current
station.
t Press (SEEK) +/– while the station name is
flashing. The unit starts searching for another
frequency with the same PI (Programme
Identification) data (“PI SEEK” appears).
NO TP
The unit will continue searching for available TP
stations.
“” or
During fast-forward or reverse, you have reached
the beginning or the end of the disc and you
cannot go any further.
2
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\02DE01INT-EUR.fm masterpage:Left
Willkommen!
Danke, dass Sie sich für diesen CD-Player von
Sony entschieden haben. Mit diesem Gerät
stehen Ihnen unterwegs folgende Funktionen zur
Verfügung.
CD-Wiedergabe:
Sie können CD-DAs und als Audio-CDs
konzipierte CD-Rs/CD-RWs abspielen lassen.
Radioempfang:
Für jeden Frequenzbereich (FM1 (UKW1),
FM2 (UKW2), FM3 (UKW3), MW und LW)
können Sie bis zu 6 Sender speichern.
BTM-Funktion (Best Tuning Memory -
Speicherbelegungsautomatik): Das Gerät
wählt die Sender mit starken Signalen aus und
speichert diese.
RDS-Funktionen:
Dieses Gerät unterstützt RDS-Funktionen
(Radio Data System) von UKW-Sendern.
Warnhinweis, wenn die Zündung Ihres
Fahrzeugs nicht über eine
Zubehörposition (ACC oder I) verfügt
Nachdem Sie die Zündung ausgeschaltet
haben, halten Sie am Gerät unbedingt (OFF)
gedrückt, bis die Anzeige ausgeblendet wird.
Andernfalls wird die Anzeige nicht
ausgeschaltet und der Autobatterie wird
Strom entzogen.
Dieses Etikett befindet sich an der Unterseite
des Gehäuses.
3
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\02DE+00COV-EURTOC.fm masterpage:Right
Inhalt
Vorbereitungen
Zurücksetzen des Geräts . . . . . . . . . . . . . . . . . . 4
Einstellen der Uhr . . . . . . . . . . . . . . . . . . . . . . . 4
DEMO-Modus. . . . . . . . . . . . . . . . . . . . . . . . . . 4
Abnehmen der Frontplatte. . . . . . . . . . . . . . . . . 4
Anbringen der Frontplatte. . . . . . . . . . . . . . . 5
Lage und Funktion der Teile und
Bedienelemente und
Grundfunktionen
Hauptgerät. . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Radio
Speichern und Empfangen von Sendern . . . . . . 7
Automatisches Speichern von Sendern
— BTM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Manuelles Speichern von Sendern . . . . . . . . 7
Einstellen gespeicherter Sender . . . . . . . . . . 7
Automatisches Einstellen von Sendern. . . . . 7
RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Übersicht. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Einstellen von AF und TA/TP . . . . . . . . . . . 8
Auswählen des Programmtyps (PTY) . . . . . 9
Einstellen der Uhrzeit (CT). . . . . . . . . . . . . . 9
Weitere Funktionen
Wechseln der Klangeinstellungen . . . . . . . . . 10
Einstellen der Klangeigenschaften
— BAL/FAD/SUB. . . . . . . . . . . . . . . . . . . 10
Einstellen der Equalizer-Kurve
— EQ3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Einstellen von Konfigurationsoptionen
— SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Verwenden gesondert erhältlicher
Fernbedienungen. . . . . . . . . . . . . . . . . . . . . . . 11
Kartenfernbedienung RM-X114 . . . . . . . . 11
Joystick RM-X4S. . . . . . . . . . . . . . . . . . . . 12
Weitere Informationen
Sicherheitsmaßnahmen. . . . . . . . . . . . . . . . . . 13
Hinweise zu CDs . . . . . . . . . . . . . . . . . . . . 13
Wartung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Ausbauen des Geräts. . . . . . . . . . . . . . . . . . . . 14
Technische Daten . . . . . . . . . . . . . . . . . . . . . . 15
Störungsbehebung. . . . . . . . . . . . . . . . . . . . . . 15
Fehleranzeigen/Meldungen . . . . . . . . . . . . 17
4
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\02DE02CD-EUR.fm masterpage:Left
Vorbereitungen
Zurücksetzen des Geräts
Bevor Sie das Gerät zum ersten Mal benutzen
oder wenn Sie die Autobatterie ausgetauscht
oder die Verbindungen gewechselt haben,
müssen Sie das Gerät zurücksetzen.
Nehmen Sie die Frontplatte ab und drücken Sie
die Taste RESET mit einem spitzen Gegenstand,
wie z. B. einem Kugelschreiber.
Hinweis
Wenn Sie die Taste RESET drücken, werden die
eingestellte Uhrzeit und einige weitere gespeicherte
Einstellungen gelöscht.
Einstellen der Uhr
Die Uhr zeigt die Uhrzeit im 24-Stunden-Format
digital an.
1 Halten Sie (SEL) gedrückt.
Die Setup-Anzeige erscheint.
2 Drücken Sie (SEL) so oft, bis „CLOCK-
ADJ“ angezeigt wird.
3 Drücken Sie (DSPL).
Die Stundenanzeige blinkt.
4 Stellen Sie mit der Lautstärketaste +/
die Stunden und Minuten ein.
Zum Verschieben der digitalen Angabe
drücken Sie (D SPL).
5 Drücken Sie (SEL).
Die Uhr beginnt zu laufen und die nächste
Setup-Anzeige erscheint.
6 Halten Sie (SEL) gedrückt.
Damit ist die Konfiguration abgeschlossen.
Zum Anzeigen der Uhr drücken Sie (DSPL).
Wenn Sie (DSPL) erneut drücken, erscheint
wieder die vorherige Anzeige.
Tipp
Mithilfe der RDS-Funktion können Sie die Uhr auch
automatisch einstellen lassen (
Seite 9).
Mit der Kartenfernbedienung
In Schritt 2 und 4 drücken Sie zum Auswählen der
Option bzw. Einstellung M oder m. In Schritt 4 drücken
Sie zum Verschieben der digitalen Angabe < oder
,.
DEMO-Modus
Wenn das Gerät ausgeschaltet wird, erscheint
zunächst die Uhrzeit und danach startet im
DEMO-Modus die Demo-Anzeige.
Zum Deaktivieren des DEMO-Modus bei
ausgeschaltetem Gerät stellen Sie bei der
Konfiguration „DEMO-OFF“ (
Seite 11) ein.
Abnehmen der Frontplatte
Um einen Diebstahl des Geräts zu verhindern,
kann die Frontplatte abgenommen werden.
Warnton
Wenn Sie den Zündschlüssel in die Position OFF
stellen, ohne die Frontplatte abzunehmen, ertönt
einige Sekunden lang ein Warnton.
Der Alarm ist nur zu hören, wenn der integrierte
Verstärker verwendet wird.
1 Drücken Sie (OFF).
Das Gerät schaltet sich aus.
2 Drücken Sie und ziehen Sie die
Frontplatte auf sich zu und heraus.
Hinweise
Lassen Sie die Frontplatte nicht fallen und drücken
Sie nicht zu stark auf die Frontplatte und das
Display.
Schützen Sie die Frontplatte vor Hitze bzw. hohen
Temperaturen und vor Feuchtigkeit. Lassen Sie sie
nicht in geparkten Autos, auf dem Armaturenbrett
oder auf der Hutablage liegen.
Tipp
Bewahren Sie die Frontplatte im mitgelieferten
Behälter auf, wenn Sie sie bei sich tragen.
Taste
RESET
(OFF)
5
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\02DE02CD-EUR.fm masterpage:Right
Anbringen der Frontplatte
Setzen Sie Teil A der Frontplatte wie abgebildet
an Teil B am Gerät an und drücken Sie dann die
linke Seite hinein, bis sie mit einem Klicken
einrastet.
Hinweis
Legen Sie auf der Innenseite der Frontplatte nichts ab.
B
A
6
CDX-S2050V/S2050C/S2050
2-348-403-21 (1)
H:\Data Disk\2348403211\234840321CDXS2050VEUR\02DE02CD-EUR.fm masterpage:Left
Lage und Funktion der Teile und Bedienelemente und
Grundfunktionen
Hauptgerät
Näheres finden Sie auf den angegebenen Seiten.
a Lautstärketaste +/–
Einstellen der Lautstärke.
b Taste SEL (Auswählen) 4, 10
Auswählen von Optionen.
c Taste SOURCE
Einschalten/Wechseln der Tonquelle (Radio/
CD).
d Taste MODE 7
Auswählen des Radiofrequenzbereichs
(UKW/MW/LW).
e CD-Einschub
Legen Sie eine CD mit der beschrifteten
Seite nach oben ein und die Wiedergabe
beginnt.
f Display
g Taste ATT (Dämpfen des Tons)
Dient zum Dämpfen des Tons. Zum Beenden
der Funktion drücken Sie die Taste erneut.
h Taste EQ3 (Equalizer) 10
Auswählen einer Equalizer-Kurve (XPLOD,
VOCAL, CLUB, JAZZ, NEW
AGE, ROCK
oder CUSTOM).
i Taste Z (Auswerfen)
Auswerfen der CD.
j Taste SEEK +/–
Radio:
Automatisches Einstellen von Sendern
(drücken) bzw. manuelle Sendersuche
(gedrückt halten).
CD:
Überspringen von Titeln (drücken) bzw.
Vorwärts-/Rückwärtssuchen in einem Titel
(gedrückt halten).
k Taste (Lösen der Frontplatte) 4
l Taste DSPL (Display)/DIM (Dimmer) 4,
7
Wechseln der angezeigten Informationen
(drücken) bzw. Ändern der Helligkeit im
Display (gedrückt halten).
m Taste SENS/BTM 7
Verbessern des Empfangs (LOCAL/MONO -
drücken) bzw. Starten der BTM-Funktion
(gedrückt halten).
n Taste RESET (befindet sich hinter der
Frontplatte)
4
o Zahlentasten
Radio:
Einstellen gespeicherter Sender (drücken)
bzw. Speichern von Sendern (gedrückt
halten).
CD:
(3): REP
Wiederholtes Wiedergeben des aktuellen
Titels bzw. der CD.
(4): SHUF
Wiedergeben von Titeln in willkürlicher
Reihenfolge.
p Taste PTY (Programmtypauswahl) 9
Auswählen von PTY bei einem RDS-Sender.
q Taste AF (Alternativfrequenzen)/TA
(Verkehrsdurchsagen) 8
Einstellen von AF und TA/TP bei einem
RDS-Sender.
r Taste OFF
Ausschalten/Stoppen der Tonquelle.
s Empfänger für die
Kartenfernbedienung 11
SEL
AF/TA
BTMDIM SHUFREP
EQ3ATT
SOURCE MODE
SEEK
CDX-S2050V
CDX-S2050C
CDX-S2050
SENS
PTY OFF
DSPL
123456
qlqa
1234 5 6 7890
qs qd qf qg qh qj qk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Sony CDX-S2050 Manuale utente

Categoria
Ricevitori multimediali per auto
Tipo
Manuale utente