Ubiquiti UVC-G3-DOME Guida Rapida

DOME

Wide-Angle 1080p Dome

IP Camera with Infrared

Model: UVC-G3-DOME

Introduction

Thank you for purchasing the Ubiquiti Networks® UniFi®Video

Camera G3 Dome. This Quick Start Guide is designed to guide

you through installation and includes warranty terms.

Package Contents

G3 Dome Camera Mounting Bracket Ceiling Backing Plate

Flat Head Screws

(M3x50, Qty. 4)

Keps Nuts

(M3, Qty. 4)

Screws

(M2.9x20, Qty. 4)

DOME

Wide-Angle 1080p Dome

IP Camera with Infrared

Model: UVC-G3-DOME

Screw Anchors

(M3x20, Qty. 4)

PoE Adapter* (24V, 0.5A)

with Mount Bracket

Power Cord* Quick Start

Guide

* Only the single-pack of the UVC-G3-DOME includes a PoE adapter and

a power cord.

TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). Shielded Ethernet cable

and earth grounding must be used for outdoor installations as conditions of product warranty.

TOUGHCable

™

is designed for outdoor installations. It is the customer’s responsibility to follow

local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver

• Drill and drill bit (6 mm for wall-mounting or 3 mm for

ceiling-mounting)

• Optional: Drywall saw or 18 mm keyhole saw

• Cat5/6 cable for indoor installations

Outdoor Installation Requirements

Important: The UVC-G3-DOME may be installed outdoors

under an eave or other protected location. Do not install

the UVC-G3-DOME in an open environment.

• Mounting location should be at least 60 cm (2 ft) from the

edge of the eave or ceiling.

• Cable feed must be pointed downwards when wall-mounted.

• Shielded Category 5 (or above) cabling should be used

for all outdoor wired Ethernet connections and should be

grounded through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Overview

Bottom View

Cable

Gland

Cable Gland For outdoor installations, ensure the rubber

Cable Gland is installed for added protection.

Security

Slot

Mounting

Bracket

Security Slot If you need to remove the UniFi Video Camera

from the Mounting Bracket, insert a paper clip in the Security

Slot to release the Lock Tab and turn the UniFi Video Camera

counterclockwise.

Ports

Ethernet

Port

LED

Microphone

Reset

Button

microSD

Slot

LED The LED will light steady blue during bootup. After

bootup, the LED will flash until the camera is adopted by

the NVR. Upon adoption the LED will light steady blue for

10minutes and then turn off.

Ethernet The Ethernet port is a 10/100 Ethernet port used to

connect the power and should be connected to the LAN and

DHCPserver.

Reset To reset to factory defaults, press and hold the Reset

button for more than 10 seconds while the camera is already

powered on.

microSD Reserved for future use.

Hardware Installation

The UniFi Video Camera can be mounted on the wall or ceiling.

The Ethernet cable can be fed through a hole in the wall/ceiling

or can be run along the wall/ceiling.

Wall Mount

1. Position the Mounting Bracket at the desired location on

the wall with the Arrow pointing up.

2. Mark the four mounting holes, and use a 6 mm drill bit to

drill the holes.

Arrow

3. If your Ethernet cable feeds through the wall, cut or drill a

circle approximately 18 mm in diameter (as shown below).

Then feed the CAT5/6 cable through the hole.

Optional 18 mm Hole for

Ethernet Cable Feed through the Wall

4. Insert the Screw Anchors into the 6 mm holes. Secure the

Mounting Bracket to the wall by inserting the Screws into

the anchors.

5. Remove the Cable Gland from the UniFi Video Camera.

Note: For indoor installations, use of the Cable Gland

is optional.

*640-00211-04*

640-00211-04

6. Feed the Ethernet cable through the cable opening on the

Cable Gland.

Note: The feed hole will stretch to accommodate the

RJ45 connector, and then seal around the cable.

7. Connect the Ethernet cable to the Ethernet port.

8. Replace the Cable Gland.

9. If the Ethernet cable is fed through the wall, skip to step10.

If the Ethernet cable runs along the mounting surface,

route the cable inside the cable channel.

10. Align the four tabs on the Mounting Bracket with the four

slots on the bottom of the camera.

Lock Tab

11. Rotate the camera clockwise until the tabs lock into place

and the Lock Tab engages.

Ceiling Mount

1. Remove the ceiling tile.

2. Center the Mounting Bracket on the front side of the ceiling

tile and rotate the bracket to the desired direction of the

camera view. Mark the four mounting screw holes and an

18 mm hole for the Ethernet cable feed.

Direction of Camera View

18 mm Hole for Ethernet Cable Feed

3. Use a 3 mm drill bit to drill the screw holes, and cut or drill

the hole for the Ethernet cable feed.

4. Insert the Flat Head Screws through the Mounting Bracket,

ceiling tile, and Ceiling Backing Plate. Fasten the screws

using the Keps Nuts. Then feed the Ethernet cable through

the tile and bracket.

5. Remove the Cable Gland from the UniFi Video Camera.

Note: For indoor installations, use of the Cable Gland

is optional.

6. Feed the Ethernet cable through the cable opening on the

Cable Gland.

Note: The feed hole will stretch to accommodate the

RJ45 connector, and then seal around the cable.

7. Connect the Ethernet cable to the Ethernet port.

8. Replace the Cable Gland.

9. Align the four tabs on the Mounting Bracket with the four

slots on the bottom of the camera.

Lock Tab

10. Rotate the camera clockwise until the tabs lock into place

and the Lock Tab engages.

11. Set the ceiling tile back into place.

Adjusting the Camera Angle

1. Press down on the Lens Cover and rotate it 10° counter-

clockwise to disengage it.

Lens Cover

Note: The O-ring creates a tight seal between the Lens

Cover and the camera body. Rotate the Lens Cover with

your hand to break the seal. Do not use any tools.

2. Pivot the Lens Cover away from the camera body and

remove it.

Protective Film

O-ring

Note: Remove the Protective Film from the Lens Cover

after camera adjustments are completed to prevent

damage during installation.

3. Rotate the camera body toward the desired view.

4. Tilt and rotate the camera lens assembly to set the desired

view angle.

5. Replace the Lens Cover by aligning the two small rib tabs

on the cover with the two slots on the camera body.

6. Ensure the Lens Cover is evenly seated, and then push

down and rotate the cover 10° clockwise to lock it in place.

Powering the UniFi Video Camera

The UVC-G3-DOME features auto-sensing 802.3af PoE and can

be powered by any of the following:

• Ubiquiti Networks UniFi Switch

• 802.3af PoE compliant switch

• Ubiquiti Networks PoE Adapter (24V, 0.5A)

The single-pack of the UVC-G3-DOME includes one PoE

adapter. For multi-pack units, PoE adapters or a UniFi Switch

may be purchased separately.

Connecting to a PoE Switch

Connect the Ethernet cable from the UniFi Video Camera

directly to a PoE port on the switch.

1 3 5 7 9 11 13 15 17 19 21 22

2 4 6 8 10 12 14 16 18 20 22 24

SFP1

SFP2

Connecting to a PoE Adapter

1. Connect the Ethernet cable from the UniFi Video Camera

to the POE port of the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the LAN port

of the PoE Adapter.

3. Connect the Power Cord to the adapter, and then plug the

Power Cord into a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the slots on the adapter with the tabs of the PoE

Mounting Bracket, and then slide the adapterdown.

La pagina sta caricando ...

Ubiquiti UVC-G3-DOME Guida Rapida

Ubiquiti UVC-G3-DOME Guida Rapida

in altre lingue

Documenti correlati