Ubiquiti UniFi UVC-Pro Guida Rapida
- Categoria
- Accessori per fotocamere
- Tipo
- Guida Rapida
1080p Indoor/Outdoor IP
Camera with Infrared and
3xOptical Zoom
Model: UVC-Pro
Introduction
Thank you for purchasing the Ubiquiti Networks
™
UniFi® Video
Camera PRO
. This Quick Start Guide is designed to guide you
through the installation of the camera and show you how to
access the Camera Configuration Interface. This Quick Start
Guide also includes the warranty terms.
The UniFi
®
Video software and User Guide are available for
download at downloads.ubnt.com/unifivideo
Package Contents
Camera PoE Adapter
(48V, 0.5A)
Power Cord Hex
Keys
Metal
Strap
1080p Indoor/Outdoor IP
Camera with Infrared and
3xOptical Zoom
Model: UVC-Pro
Pan Head Screws
(M4x30, Qty. 4)
Screw Anchors
(Qty. 4)
Ethernet
Sleeve
Mounting
Template
Quick Start
Guide
Installation Requirements
Wall-Mounting:
• Drill
• Drill bit, 7 mm
• Hole saw, 45 mm (optional)
• Phillips screwdriver
Pole-Mounting:
• Screwdriver or 7 mm socket driver
TERMS OF USE: Shielded Ethernet cable and earth grounding must be used as conditions of
product warranty. TOUGHCable™ is designed for outdoor installations. It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, and Dynamic Frequency Selection (DFS) requirements.
Optional Accessories
Ubiquiti Networks offers additional accessories that can be
purchased for use with the UniFi Video Camera PRO. For
accessory installation instructions, refer to the Quick Start
Guide that accompanies the product.
Cable Accessory (UVC-Pro-C)
The UniFi Video Camera PRO Cable Accessory provides
additional connectivity options for UniFi Video Camera PRO,
including audio in/out and mFi® mPort options. There is also a
reset button and PoE/Ethernet connector.
Audio In/Out
Reset
mPort
POE/Ethernet
Connects to
UVC-Pro
Large Pole Mount (UVC-Pro-M)
The UniFi Video Camera PRO Large Pole Mount accommodates
larger poles up to 160 mm wide.
Hardware Overview
Camera Adjustment
Adjusts Camera Up or Down
Rotates CameraRotates Base
Waterproof Gland
The UniFi Video Camera PRO has a waterproof gland for
connecting Ethernet. Below are the components that make up
the waterproof gland:
Seal
Housing
Compression Nut
Ethernet Connector
Reset Pins
To reset the UniFi Video Camera PRO to factory default
settings, use the hex keys or an electric conductor to short the
pins. (The two Reset Pins are called out in the diagram above.)
Installation Overview
The installation process differs depending on if you are
mounting the camera on a wall or on a pole. Follow the
instructions for the installation that you are performing.
Wall Mount
1. Remove the adhesive Mounting Template from the backing
and place the label on the wall where you want the camera.
2. Use a 7 mm drill bit to drill the four anchor holes in the wall.
(Optional) If threading the cabling through the wall, drill
the center hole using a 45 mm hole saw.
3. Insert the four Screw Anchors into the wall.
*640-00059-03*
640-00059-03
4. Thread the cabling through the wall or one of the recessed
areas on the Mounting Bracket Base.
Note: There are two recessed areas for an Ethernet
cable on the Mounting Bracket Base. Place the Ethernet
cable in the recessed area closest to your power
source.
5. Use a Phillips screwdriver to secure the camera to the wall
with the four Pan Head Screws.
Proceed to “Connecting Power and Ethernet”.
Pole Mount
To mount the camera on a pole, use the included Metal Strap:
1. Open the Metal Strap by turning the locking screw
counter-clockwise.
2. Slide the Metal Strap through the back of the camera.
3. Wrap the Metal Strap around the pole. Use a screwdriver or
7 mm socket drive to turn the locking screw clockwise and
securely fasten the strap to the pole.
Connecting Power and Ethernet
1. Disassemble the waterproof gland by turning the
Compression Nut counter-clockwise.
2. Seperate the Seal from the Housing.
3. Insert the Ethernet cable through the Compression Nut and
the Housing. Ensure the threads of the Compression Nut
face the notches on the Housing.
4. Wrap the Seal around the Ethernet cable.
5. Slide the Seal into the Housing.
6. Connect the Ethernet cable to the Ethernet Connector on
the camera.
Optional Step: The included Ethernet Sleeve can be placed
over the Ethernet connector to allow the cable to be
removed easier.
7. Enclose the waterproof gland by turning the Compression
Nut clockwise. Turn the Compression Nut until the Seal
extrudes slightly from the end of the Compression Nut.
Seal
Note: The Seal should be extruding from the
Compression Nut when properly tightened to
prevent water from entering.
8. Remove the protective plastic film from the camera lens.
9. Connect the other end of the Ethernet cable to one of the
following:
• PoE Adapter Connect the camera to the Ethernet port
labeled POE on the included PoE Adapter.
• TOUGHSwitch PRO or Carrier Connect the camera to a
port with 48V power enabled and skip steps 10 and 11.
OR
10. Connect an Ethernet cable from your LAN to the Ethernet
port labeled LAN on the PoE Adapter.
11. Connect the other end of the power cord to a power outlet.
UniFi Video
The UniFI Video software is pre-installed on the UniFi NVR
(sold separately). If you do not have the UniFi NVR, you can
download and install the latest version of the UniFi Video
software at downloads.ubnt.com/unifivideo; the UniFi Video
auto-management feature should automatically detect and
install your new camera(s).
Proceed to Adjusting the Camera View.
Camera Configuration Interface
Access the Camera Configuration Interface if you have not
yet installed the UniFi Video software, or plan to use the UniFi
Video Camera as a stand-alone camera without the UniFi
Video software.
1. Ensure that your host machine is connected to the same
LAN as the UniFi Video Camera.
2. The UniFi Video Camera is set to DHCP by default. If you
have a router or DHCP server providing addresses on your
network, please check your DHCP Client Table or download
the Ubiquiti Discovery Tool from:
http://www.ubnt.com/download#app
Note: If you do not have a DHCP server, the camera
defaults to the IP address 192.168.1.20.
3. Launch your web browser, and in the address field, type
https:// and then the IP address of the camera, for example:
https://192.168.1.20. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username
and Password fields and click Login.
5. The Main screen will appear and you should see a live
video stream from the UniFi Video Camera.
Adjusting the Camera View
Adjust Camera Up or Down
Using Large Hex Key
Rotate CameraRotate Base
Use Small Hex Key
Ensure you have removed the protective plastic
film from the camera lens.
For details on using the UniFi Video software, refer to our
website at: documentation.ubnt.com/unifivideo
Specifications
UniFi Video Camera PRO
Dimensions 322 x 100 x 100 mm (12.67 x 3.93 x 3.93")
Weight 2.15 kg (4.73 lbs)
Ports (1) 10/100 Ethernet Port
Sensor 3M WDR Sensor
Lens 3X Optical Zoom, f= 3-9 mm
Infrared Yes
Buttons Factory Reset Button
Power Method Passive PoE (48V, 0.5A), 802.3af
Power Supply 48V, 0.5A PoE Adapter Included
Max. Power Consumption 12.5 W
Certications CE, FCC, IC
Mounting Pole/Wall/Ceiling Adapter Kit Included
Protection Rating IP67 Waterproof
Operating Temperature -40 to 50° C (-40 to 122° F)
Operating Humidity 20 - 90% Non-Condensing
Video
Video Compression H.264
Resolution 1080p Full HD
Maximum Frame Rate 30 FPS
Image Setting Brightness, Contrast, Sharpness, Saturation,
Noise Reduction, 50 Hz/60 Hz
General
Processor ARM 1136J-S 528 MHz
Memory 256 MB DDR3, 256 MB Flash
View Angle 44.4° W - 15.7° T (V)
81.0° W - 27.9° T (H)
94.0° W - 32.1° T (D)
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not point the camera toward the sun.
The sun’s heat can damage the camera’s internal
components.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.
Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal
physical, electromagnetic or electrical stress, including lightning
strikes, or accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.
Returns
No Products will be accepted for replacement or repair without obtaining
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS
during the warranty period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not
be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty.
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible
for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including
the Products) for buyer’s application and/or failure of products (including
the Products) to meet government or regulatory requirements.
Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO
THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations
Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operations of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
Industry Canada
This Class A digital apparatus complies with Canadian CAN ICES-3(B).
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
Cet appareil numérique de la classe A est confrome à la norme NMB-3(B)
Canada.
Pour réduire le risque d’interférence aux autres utilisateurs, le type
d’antenne et son gain doivent être choisies de façon que la puissance
isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire
pour une communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada exempts de
licence norme(s). Son fonctionnement est soumis aux deux conditions
suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais fonctionnement du
dispositif.
Australia and New Zealand
Warning: This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ubiquiti UniFi UVC-Pro Guida Rapida
- Categoria
- Accessori per fotocamere
- Tipo
- Guida Rapida
in altre lingue
Documenti correlati
-
Ubiquiti UVC-G3 Guida Rapida
-
UBIQUIT UVC-Dome Guida utente
-
Ubiquiti Networks UVC-3 Guida utente
-
-
-
-
-
-
-
Ubiquiti Networks UAP-AC Guida utente
