Yamaha RMio64 Manuale del proprietario

Marca: Yamaha

Modello: RMio64

Tipo: Manuale del proprietario

EnglishDeutschFrançaisEspañolPortuguêsItalianoРусский

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manual do Proprietário

Manuale di istruzioni

Руководство пользователя

I/O RACK

AUDIO INTERFACE

RMio64-D Owner’s Manual

Explanation of Graphical Symbols

Explication des symboles

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension

dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions

importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table

specified by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid

injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been

dropped.

(UL60065_03)

PRÉCAUTIONS CONCER-

NANT LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l’appareil

conformément aux instructions du fabricant.

8 Ne pas installer l’appareil à proximité d’une source de chaleur comme

un radiateur, une bouche de chaleur, un poêle ou tout autre appareil

(y compris un amplificateur) produisant de la chaleur.

9 Ne pas modifier le système de sécurité de la fiche polarisée ou de la

fiche de terre. Une fiche polarisée dispose de deux broches dont une

est plus large que l’autre. Une fiche de terre dispose de deux broches

et d’une troisième pour le raccordement à la terre. Cette broche plus

large ou cette troisième broche est destinée à assurer la sécurité de

l’utilisateur. Si la fiche équipant l’appareil n’est pas compatible avec

les prises de courant disponibles, faire remplacer les prises par un

électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas

piétinés ni coincés, en faisant tout spécialement attention aux fiches,

prises de courant et au point de sortie de l’appareil.

11 Utiliser exclusivement les fixations et accessoires spécifiés par le

fabricant.

12 Utiliser exclusivement le chariot, le stand, le trépied,

le support ou la table recommandés par le fabricant

ou vendus avec cet appareil. Si l’appareil est posé

sur un chariot, déplacer le chariot avec précaution

pour éviter tout risque de chute et de blessure.

13 Débrancher l’appareil en cas d’orage ou lorsqu’il doit

rester hors service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire réparer

l’appareil s’il a subi tout dommage, par exemple si la fiche ou le

cordon d’alimentation est endommagé, si du liquide a coulé ou des

objets sont tombés à l’intérieur de l’appareil, si l’appareil a été exposé

à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas

normalement ou est tombé.

(UL60065_03)

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION :

POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER

LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT

L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,

FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.

ATTENTION

RISQUE DE CHOC

ELECTRIQUE-NE PAS OUVRIR

The above warning is located on the top of the unit.

L’avertissement ci-dessus est situé sur le dessus de l’unité.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

RMio64-D Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted

by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instruc-

tions found in the users manual, may cause interference harmful

to the operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not occur in

all installations. If this product is found to be the source of interfer-

ence, which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of the fol-

lowing measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service Divi-

sion, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Audio Interface

Model Name : RMio64-D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference

that may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

(FCC DoC)

이 기기는 가정용 (B 급 ) 전자파적합기기로서 주로

가정에서 사용하는 것을 목적으로 하며 , 모든

지역에서 사용할 수 있습니다 .

(class b korea)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED IMPORTANT. The

wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not cor-

respond with the coloured markings identifying the terminals in your plug

proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected to the

terminal in the plug which is marked by the letter E or by the safety earth

symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal which

is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED.

(3 wires)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

RMio64-D Owner’s Manual

Contents

Introduction 7

Features .................................................................7

Precautions for Rack Mounting..............................7

Firmware Updates..................................................7

Conventions in this Manual....................................7

Controls and Functions 8

Front Panel .............................................................8

Rear Panel..............................................................9

Connection 11

About Dante .........................................................11

Notes Regarding the Use of Network Switches...11

Connecting Dante-compatible Devices...............11

Connecting MADI-compatible Devices ...............12

Connecting AC Power..........................................13

Power on and off ..................................................13

Dante Network Settings and Audio Routing ........14

Selecting MADI Input Rate...................................14

Panel Lock ...........................................................14

Signal Flow 14

Dante to MADI......................................................14

MADI to Dante......................................................14

MADI Split ............................................................14

Word Clock 15

About Word Clock................................................15

Selecting a Word Clock Source...........................15

MADI SRC (Sampling Rate Converter) 15

Setting Examples .................................................15

Displaying the MADI Input and Output Signals...16

Remote Control 16

Remote Controllable Parameters .........................16

Control from NUAGE Workgroup Manager..........16

Direct Monitoring 17

RMio64-D Setup 17

Troubleshooting 17

Updating ............................................................. 17

Routing / Patching............................................... 18

Remote Control ................................................... 18

Other Issues ........................................................ 18

Restoring Factory Settings.................................. 18

Index 19

Specifications (at the end of the book)

Included Accessories

• Owner’s Manual

• AC power cord (European model includes two

different cords.)

RMio64-D Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to avoid

the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other

hazards. These precautions include, but are not limited

to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or otherwise

damage the cord, place heavy objects on it, or place it in a

position where anyone could walk on, trip over, or roll anything

over it.

• Only use the voltage specified as correct for the device. The

required voltage is printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the one

you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or

dust which may have accumulated on it.

• Be sure to connect to an appropriate outlet with a protective

grounding connection. Improper grounding can result in

electrical shock, damage to the device(s), or even fire.

Do not open

• This device contains no user-serviceable parts. Do not open

the device or attempt to disassemble the internal parts or

modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in damp

or wet conditions, or place on it any containers (such as

vases, bottles or glasses) containing liquids which might spill

into any openings. If any liquid such as water seeps into the

device, turn off the power immediately and unplug the power

cord from the AC outlet. Then have the device inspected by

qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Fire warning

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

If you notice any abnormality

• When one of the following problems occur, immediately turn

off the power switch and disconnect the electric plug from the

outlet. Then have the device inspected by Yamaha service

personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

• If this device should be dropped or damaged, immediately

turn off the power switch, disconnect the electric plug from the

outlet, and have the device inspected by qualified Yamaha

service personnel.

CAUTION

Always follow the basic precautions listed below to avoid

the possibility of physical injury to you or others, or

damage to the device or other property. These

precautions include, but are not limited to, the following:

Power supply/power cord

• When removing the electric plug from the device or an outlet,

always hold the plug itself and not the cord. Pulling by the

cord can damage it.

• Remove the electric plug from the outlet when the device is

not to be used for extended periods of time, or during

electrical storms.

Location

• Do not place the device in an unstable position where it might

accidentally fall over.

• Do not block the vents. This device has ventilation holes at the

front/rear to prevent the internal temperature from becoming

too high. In particular, do not place the device on its side or

upside down. Inadequate ventilation can result in overheating,

possibly causing damage to the device(s), or even fire.

• Do not place the device in a location where it may come into

contact with corrosive gases or salt air. Doing so may result in

malfunction.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you

are using is easily accessible. If some trouble or malfunction

occurs, immediately turn off the power switch and disconnect

the plug from the outlet. Even when the power switch is turned

off, electricity is still flowing to the product at the minimum

level. When you are not using the product for a long time,

make sure to unplug the power cord from the wall AC outlet.

• If the device is mounted in an EIA standard rack, carefully

read the section “Precautions for Rack Mounting” on page 7.

Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), malfunction, or even fire.

Connections

• Before connecting the device to other devices, turn off the

power for all devices. Before turning the power on or off for all

devices, set all volume levels to minimum.

PA_en_4 1/2

RMio64-D Owner’s Manual

Maintenance

• Remove the power plug from the AC outlet when cleaning the

device.

Handling caution

• Avoid inserting or dropping foreign objects (paper, plastic,

metal, etc.) into any gaps or openings on the device (vents,

etc.) If this happens, turn off the power immediately and

unplug the power cord from the AC outlet. Then have the

device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects

on it, and avoid use excessive force on the buttons, switches

or connectors.

NOTICE

To avoid the possibility of malfunction/ damage to the product,

damage to data, or damage to other property, follow the notices

below.

Handling and Maintenance

• Do not use the device in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices.

Otherwise, the device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or

extreme cold or heat (such as in direct sunlight, near a heater,

or in a car during the day), in order to prevent the possibility of

panel disfiguration, unstable operation, or damage to the

internal components.

• Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning fluids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic

changes in ambient temperature — when the device is moved

from one location to another, or air conditioning is turned on or

off, for example. Using the device while condensation is

present can cause damage. If there is reason to believe that

condensation might have occurred, leave the device for

several hours without turning on the power until the

condensation has completely dried out.

• Always turn the power off when the device is not in use.

Information

About functions/data bundled with the product

• This product uses Dante Brooklyn II.

Refer to the Audinate website (English) for details on the open

source licenses for the particular software.

https://www.audinate.com/software-licensing

About copyrights

• Copying of the commercially available musical data including

but not limited to MIDI data and/or audio data is strictly

prohibited except for your personal use.

About this manual

• The illustrations and screens as shown in this manual are for

instructional purposes only.

• Windows is a registered trademark of Microsoft

Corporation

in the United States and other countries.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

(weee_eu_en_01)

(rear_en_01)

European Models

Inrush Current based on EN 55103-1:2009

2.0 A (on initial switch-on)

2.0 A (after a supply interruption of 5s)

Conforms to Environments: E1, E2, E3 and E4

Yamaha cannot be held responsible for damage caused by

improper use or modifications to the device, or data that is

lost or destroyed.

Information for Users on Collection and

Disposal of Old Equipment

This symbol on the products, packaging, and/

or accompanying documents means that used

electrical and electronic products should not

be mixed with general household waste.

For proper treatment, recovery and recycling of

old products, please take them to applicable

collection points, in accordance with your national

legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to

save valuable resources and prevent any potential negative

effects on human health and the environment which could

otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old

products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased

the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment,

please contact your dealer or supplier for further

information.

[Information on Disposal in other Countries outside

the European Union]

This symbol is only valid in the European Union. If you wish

to discard these items, please contact your local authorities

or dealer and ask for the correct method of disposal.

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the top of

the unit. You should note this serial number in the space pro-

vided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

PA_en_4 1/2

RMio64-D Owner’s Manual

Introduction

Thank you for choosing the Yamaha RMio64-D audio

interface.

To take full advantage of the superior functions and

performance offered by the RMio64-D, and to enjoy

years of trouble-free use, be sure to read this owner’s

manual carefully before operation.

Features

The RMio64-D is a digital interface that lets you transfer

up to 64 digital inputs and 64 digital outputs between a

Dante network and a MADI-compatible device. By

connecting both Dante and MADI, this product can be

used for wide variety of applications such as

broadcasting, live recording, and post production. In

addition, full control of this unit’s settings has been

achieved through tight integration with Yamaha’s Dante

compatible devices.

• Supports redundancy for both Dante and MADI, and

provides a high level of reliability.

• Sampling rate converter (SRC) in MADI inputs and

outputs.

• Signals can be looped back from MADI optical to

coaxial, or from coaxial to optical (MADI split).

• Enhanced linkage functionality with Steinberg

Nuendo, such as direct monitoring and high-precision

clock sync with Nuendo SyncStation.

Precautions for Rack

Mounting

This unit is rated for operation at ambient temperatures

ranging from 0 to 40 degrees Celsius. When mounting

the unit with other RMio unit(s) or other device(s) in an

EIA standard equipment rack, internal temperatures can

exceed the specified upper limit, resulting in impaired

performance or failure. When rack mounting the unit,

always observe the following requirements to avoid heat

buildup:

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave more than 1U of space between the RMio

and other equipment. Also either leave the open

spaces uncovered or install appropriate ventilating

panels to minimize the possibility of heat buildup.

• To ensure sufficient airflow, leave the rear of the rack

open and position it at least 10 centimeters from walls

or other surfaces. If you’ve installed a fan kit, there

may be cases in which closing the rear of the rack will

produce a greater cooling effect. Refer to the rack

and/or fan unit manual for details.

Firmware Updates

This product enables you to update the unit firmware to

improve operations, add functions, and correct possible

malfunctions. The following two types of firmware are

available for the unit:

•Unit’s firmware

• Dante module firmware

You must update each type of firmware separately.

Details on updating the firmware are available on the

following website:

http://www.yamahaproaudio.com/

For information on updating the unit, refer to the firmware

update guide available on the website.

NOTE

It is necessary to update multiple devices depending on the

version of each device in the Dante network. For details, refer to

the firmware compatibility available on the website.

http://www.yamahaproaudio.com/

Conventions in this Manual

Screen Shots

The example screen shots shown in this manual are from

the Windows version, while those for Steinberg Nuendo

are from Nuendo 6.5. Therefore, the actual displays

might appear different if you are using a different version

of Nuendo. For details, see the Owner’s Manual (PDF)

from the “Help” menu in Nuendo.

RMio64-D Owner’s Manual

Controls and Functions

Front Panel

MADI [SRC ON] indicator

MADI [SRC ON] key

Turns the MADI SRC (Sampling Rate Converter) on

(indicator lights) and off.

MADI [SRC WCLK IN] indicator

MADI [SRC WCLK IN] key

Selects whether the word clock that is input to the

MADI [WCLK IN FOR SRC] connector on the rear

panel is used or not as the reference MADI SRC

clock. (Indicator lights when used.)

If no valid word clock input is detected, this indicator

flashes.

MADI [INPUT RATE Fs 44.1kHz] indicator

MADI [INPUT RATE Fs 48kHz] indicator

These indicators turn on accordingly when the

device automatically detects the MADI input signal

as 44.1 kHz or 48 kHz. If no valid MADI input signal is

detected, both indicators remain off.

MADI [INPUT RATE 1Fs] indicator

MADI [INPUT RATE 2Fs] indicator

MADI [INPUT RATE 4Fs] indicator

MADI [INPUT RATE] 1Fs/2Fs/4Fs key

Selects 1Fs (1x), 2Fs (2x), or 4Fs (4x) in combination

with the MADI input rate. For example, for a MADI

input rate of 192 kHz (4x 48 kHz), confirm that the

MADI [INPUT RATE Fs 48kHz] indicator is on, and

then select [4Fs].

NOTE

If you select [2Fs], the unit automatically detects the MADI

input signal frame format (48 kHz/96 kHz).

MADI [STATUS INPUT] indicator

MADI [STATUS OUTPUT] indicator

MADI [STATUS] INPUT/OUTPUT key

Selects whether to display the MADI input signal or

MADI output signal information (frame format/

number of channels).

NOTE

You can use this key to lock the panel to prevent operation

of the keys (page 14).

MADI [STATUS FRAME 48k] indicator

MADI [STATUS FRAME 96k] indicator

Displays the frame format of the MADI input signal or

output signal. For 44.1 kHz and 48 kHz, the [STATUS

FRAME 48k] indicator is lit. For 88.2 kHz and 96 kHz,

the [STATUS FRAME 96k] indicator is lit. If no valid

MADI input signal is detected, both indicators remain

off.

NOTE

If no valid MADI input signal is detected, the MADI output

signal is set to 48 kHz/64 channels.

MADI [STATUS CHANNEL 64] indicator

MADI [STATUS CHANNEL 56] indicator

Displays the number of channels (64 or 56) for the

MADI input signal or output signal. If no valid MADI

input signal is detected, both indicators remain off.

NOTE

If no valid MADI input signal is detected, the MADI output

signal is set to 48 kHz/64 channels.

WORD CLOCK [WCLK IN] indicator

WORD CLOCK [MADI] indicator

WORD CLOCK [DANTE] indicator

WORD CLOCK WCLK IN/MADI/DANTE key

Selects the word clock source.

WCLK IN Uses the word clock signal that is input

from the [WORD CLOCK IN] connector

on the rear panel. This indicator flashes if

no valid word clock input is detected.

MADI Uses the word clock of the MADI input

signal. This indicator flashes if no valid

word clock input is detected.

DANTE Uses the word clock from the Dante

network.

RMio64-D Owner’s Manual

WORD CLOCK [Fs] indicator

Displays the word clock frequency that the unit is

using. This indicator flashes if no word clock is

synced.

Dante [SYSTEM] indicator

Displays the operating status of the unit.

Dante [SYNC] indicator

Displays the sync status between the Dante network

and this unit.

[EXTERNAL CONTROL] indicator

This indicator turns on when a parameter which can

be operated only from an external remote control is

effective.

For details about parameters that can be operated

by remote control, see “Remote Control” (page 16).

Power indicator

[I]/[ ] (Power Switch)

Turns power of the unit to on [ ] or off [ ].

The indicator turns on when AC power is on.

CAUTION

Even when the power switch is turned off, a small

amount of current is flowing through the unit. When you

are not using the product for a long time, make sure to

unplug the power cord from the AC outlet.

NOTE

Rapidly turning the unit on and off in succession can cause

it to malfunction. After turning the unit off, wait for at least 6

seconds before turning it on again.

Rear Panel

AC IN connector

Connect the supplied AC power cord here. First

connect the AC power cord to the RMio unit, then

insert the power cord plug into an AC power outlet.

The supplied AC power cord features a V-lock

mechanism via a latch, which prevents the power

cord from coming off accidentally.

Insert the cable plug all the way until it locks in

securely.

CAUTION

Be sure to turn the power off before connecting or

disconnecting the power cord.

Press the latch button on the plug to disconnect the

power cord.

Dante [PRIMARY] connector

Dante [SECONDARY] connector

These are etherCON (RJ-45) connectors for

connecting to the Dante network.

NOTE

• Use STP (Shielded Twisted Pair) cable to prevent

electromagnetic interference. Make sure that the metal

parts of the plugs are electrically connected to the STP

cable shield by conductive tape or comparable means.

• Connect only Dante-compatible devices or GbE-

compatible devices (including a computer).

• Cables of up to 100 meters (theoretical value) can be

used.

Green

(indicator lights)

The unit is working properly.

Green

(indicator flashes)

The firmware updating is in

progress.

Red

(indicator lights)

The memory on the unit does not

work properly.

Red

(indicator flashes)

An error has occurred in the Dante

module.

Green

(indicator lights)

The device is working as the slave

on the Dante network.

Green

(indicator flashes)

The device is working as the

master on the Dante network.

Orange

(indicator lights)

Synchronization with the Dante

network is in progress.

Orange

(indicator flashes)

The device is not synchronized

with the Dante network.

RMio64-D Owner’s Manual

Dante [PRIMARY LINK/ACT] indicator

Dante [PRIMARY 1G] indicator

Dante [SECONDARY LINK/ACT] indicator

Dante [SECONDARY 1G] indicator

Displays the transmission status with the Dante

network.

Dante [UNIT ID] rotary switch

Sets the ID for this unit. The setting range of the UNIT

ID is 16 hexadecimal numbers from 0 to F. If there are

multiple Dante-compatible devices from Yamaha that

require an ID setting connected to the same network,

set a different ID for each device. Make sure to

change the settings of the rotary switch while the

power to the unit is turned off; otherwise, the ID

setting will not be effective.

Dante DIP switches

Used to change unit settings. Make sure to change

the settings of the DIP switches while the power to

the unit is turned off; otherwise, the ID setting will not

be effective. For details, see “Connecting Dante-

compatible Devices” (page 11) and “Restoring

Factory Settings” (page 18).

[SYSTEM LINK OUT] connector

This BNC connector is used to connect to the AES 2

IN connector on the Steinberg Nuendo SyncStation.

This connection provides a highly precise clock sync

between this unit and Nuendo.

When not connecting with Nuendo SyncStation, two

of the channels for the Dante input signals are output

as AES/EBU signals. Connecting the AES/EBU-

compatible devices to this connector allows Dante

signals to be converted to AES/EBU signals and can

be output. In the default settings, Dante channels 1

and 2 are used for output. You can use a remote

control to change the output channels. For details,

see “Remote Control” (page 16).

[WORD CLOCK OUT] connector

[WORD CLOCK IN] connector

These are BNC connectors used to transmit and

receive word clock signals.

MADI DIP switches

Used to change unit settings. Make sure to change

the settings of the DIP switches while the power to

the unit is turned off; otherwise, the ID setting will not

be effective. For details, see “Connecting MADI-

compatible Devices” (page 12) and “MADI Split”

(page 14).

MADI [WCLK IN FOR SRC] connector

This is a BNC connector that can be used to directly

input word clock signals for MADI SRC.

MADI [COAXIAL OUT] connector

MADI [COAXIAL IN] connector

These are BNC connectors used to connect with

MADI-compatible devices.

NOTE

Coaxial cables of up to 100 meters (theoretical value) can

be used.

MADI [OPTICAL OUT] connector

MADI [OPTICAL IN] connector

These are SC connectors used to connect with

MADI-compatible devices.

NOTE

• Use a multimode optical cable with 50-micron core/125-

micron cladding diameters, or 62.5-micron core/125-

micron cladding diameters.

• Optical cables of up to 2,000 meters (theoretical value)

can be used.

• Use SC duplex connectors.

• Attach the supplied rubber cap to the connector to

prevent dust from collecting when the cable is not

connected.

LINK/ACT These indicators flash rapidly if the

Ethernet cables are connected properly.

1G These indicators are lit when the Dante

network is functioning as Giga-bit

Ethernet.

RMio64-D Owner’s Manual

Connection

This section describes the following connections.

About Dante

Dante is a network audio protocol developed by

Audinate. It is designed to deliver multi-channel audio

signals at various sampling and bit rates, as well as

device control signals over a Giga-bit Ethernet (GbE)

network.

Visit the Audinate website for more details on Dante:

http://www.audinate.com/

More information on Dante is also posted on the Yamaha

Pro Audio website:

http://www.yamahaproaudio.com/

Notes Regarding the Use of

Network Switches

Do not use the EEE functionality (*) of network switches

on a Dante network.

Although mutual power consumption settings between

switches that support the EEE functionality are adjusted

automatically, there are some switches for which such

mutual settings are not adjusted correctly.

This may cause EEE to be enabled in Dante networks

when it is not appropriate, resulting in poor

synchronization performance and occasional dropouts.

Therefore we strongly recommend the following.

• If you use managed switches, please disable the EEE

functionality. Do not use switches that prevent EEE

functionality from being disabled.

• When using unmanaged switches, do not use

switches that support EEE functionality. EEE

functionality cannot be disabled for such switches.

* EEE (Energy Efficient Ethernet) is a technology that reduces

switch power consumption during periods of low network

traffic. It is also referred to as Green Ethernet and

IEEE802.3az.

Connecting Dante-compatible

Devices

You can connect the RMio64-D to a Dante network in the

following ways.

Daisy Chain Network

A daisy chain network is a wiring scheme in which

multiple devices are connected together in sequence.

This connection method is suitable for a simple system

with a small number of devices.

However, if a large number of devices are connected,

you will also need to manually increase the latency value

significantly. Also, if a connection is broken in a daisy

chain network, the signal flow is interrupted at that point

and no signal will be transferred beyond that point.

 Settings

• Turn off Dante DIP switch 1 (UP).

• If there are multiple Dante-compatible devices from

Yamaha that require an ID setting connected to the

same network, set a different ID for each device. Make

sure to change the settings of the rotary switch while

the power to the unit is turned off; otherwise, the ID

setting will not be effective.

Connecting Dante-compatible Devices (page 11)

Connecting MADI-compatible Devices (page 12)

Connecting AC Power (page 13)

Dante Audio Routing (page 14)

Selecting MADI Input Rate (page 14)

CL5

Rio3224-D (ID#1)

RMio64-D (ID#2)

PRIMARY

SECONDARY

PRIMARY

RMio64-D Owner’s Manual

Star Network

In a star network, each device is connected to a central

GbE-compatible network switch. This connection

enables you to configure a wide-band, large-scale

network.

 Settings

• Turn on Dante DIP switch 1 (DOWN).

• If there are multiple Dante-compatible devices from

Yamaha that require an ID setting connected to the

same network, set a different ID for each device. Make

sure to change the settings of the rotary switch while

the power to the unit is turned off; otherwise, the ID

setting will not be effective.

NOTE

• We recommend a network switch that features various

functions for controlling and monitoring the network (such as

QoS).

• Do not use the EEE functionality of network switches.

Star Network (Redundant Network)

You can set up a star network redundant so that there is

no audio loss even if interference occurs on the network.

A redundant network consists of two circuits, a primary

circuit and a secondary circuit. Normally, the network

operates on the primary circuit. However, if the primary

connection is broken, the secondary circuit will

automatically take over communications.

 Settings

• Turn on Dante DIP switch 1 (DOWN).

• If there are multiple Dante-compatible devices from

Yamaha that require an ID setting connected to the

same network, set a different ID for each device. Make

sure to change the settings of the rotary switch while

the power to the unit is turned off; otherwise, the ID

setting will not be effective.

NOTE

• We recommend a network switch that features various

functions for controlling and monitoring the network (such as

QoS).

• Do not use the EEE functionality of network switches.

• The Dante [SYNC] indicator flashes as follows when

communication error occurs on the Dante Redundant

Network.

Connecting MADI-compatible

Devices

You can connect the RMio64-D to MADI-compatible

devices using either 75Ω coaxial (BNC) or optical (SC)

cables.

Using 75Ω Coaxial Cables

NOTE

Coaxial cables of up to 100 meters (theoretical value) can be

used.

Error on a primary network

Error on a secondary network

Light or

flash

(green)

Flashes

once

(orange)

Light or

flash

(green)

Flashes

twice

(orange)

Computer

Network switch A

Network switch B

Primary Dante

Secondary Dante

CL5

Rio3224-D (ID#1)

RMio64-D (ID#2)

MADI-compatible device

RMio64-D

COAXIAL

OUT

COAXIAL

OUT

COAXIAL

RMio64-D Owner’s Manual

Using Optical Cables

NOTE

Optical cables of up to 2,000 meters (theoretical value) can be

used.

Redundant Connection (Input only)

You can set up a redundant connection using both 75Ω

coaxial cables and optical cables, so that there is no

input signal loss even if interference occurs in the

connection.

In addition, the input signal from the Dante network is

output from both the MADI [COAXIAL OUT] and MADI

[OPTICAL OUT] connectors, regardless of the MADI

redundancy settings.

 Settings

• To set up a redundant connection, turn on MADI DIP

switch 2 (DOWN).

• To give priority to the coaxial cables, turn on MADI DIP

switch 1 (DOWN).

• To give priority to the optical cables, turn off MADI DIP

switch 1 (UP).

NOTE

Make sure to change the settings of the DIP switches while the

power to the unit is turned off; otherwise, the ID setting will not

be effective.

When using the word clock input from the MADI [WCLK

IN FOR SRC] connector as the MADI SRC reference

clock, the redundant function is unavailable.

Connecting AC Power

1. Turn the unit off.

2. Connect the plug on the AC power cord to

the AC IN connector on the rear panel of the

unit.

3. Connect the other side of the plug on the

AC power cord to a power supply socket.

NOTE

• When removing the AC power cord, perform these steps in

reverse.

• Press the latch button on the plug to disconnect the power

cord.

WARNING

• The RMio64-D has been designed assuming it a proper

ground connection is used. To prevent electrical shock

and damage to devices, use the included AC power cord

to create a secure ground connection. If you do not know

how to make a proper ground connection, contact a

Yamaha service center listed at the end of this manual.

• Be sure to use only the included power cord with this unit.

Use of a different power cord could result in abnormal

heat and electrical shock.

CAUTION

• Be sure to turn the power off before connecting or

disconnecting the power cord.

• Even when the power switch is turned off, a small amount

of current is flowing through the unit. When you are not

using the product for a long time, make sure to unplug the

power cord from the power supply outlet.

Power on and off

When turning on the AC power in your audio system,

always turn on the power amplifier LAST, to avoid

speaker damage. When turning the power off, the power

amplifier should be turned off FIRST for the same

reason.

MADI-compatible device

RMio64-D

OPTICAL

OUT

OPTICAL

OUT

OPTICAL

MADI-compatible device

Coaxial cable

priority

Optical cable

priority

RMio64-D

RMio64-D Owner’s Manual

Dante Network Settings and

Audio Routing

With the Dante network, you can route the audio input

and output of multiple Dante devices in any way you like.

This requires you to set which channel signals are sent

to which inputs. The routing for connecting MADI with

the Dante network is fixed on the RMio64-D. Therefore,

any changes in routing are made in the Dante network.

Use Dante Controller to configure the audio routing of

the Dante network.

You can download Dante Controller from the following

website:

http://www.yamahaproaudio.com/

Refer to the Dante Controller owner’s manual (available

from the same website) for details about Dante

Controller.

Selecting MADI Input Rate

Use the MADI [INPUT RATE] 1Fs/2Fs/4Fs keys on the

front panel to select the MADI input rate.

For example, for a MADI input rate of 192 kHz (4x 48

kHz), confirm that the MADI [INPUT RATE Fs 48kHz]

indicator is on, and then select [4Fs]. If no valid MADI

input signal is detected, both indicators remain off.

Panel Lock

You can lock the panel to prevent unintended changes

and operations. While the lock is engaged, all controllers

on the front panel are inoperable. To engage the lock,

press and hold the MADI [STATUS] INPUT/OUTPUT key

for at least 3 seconds. All front panel indicators (except

the power indicator) flash, indicating all controllers are

locked. To disengage the lock, press and hold the MADI

[STATUS] INPUT/OUTPUT key for at least 3 seconds.

NOTE

Even if the front panel is locked, you can use remote control to

make changes to the settings.

For the latest information about remote control compatible

devices, refer to the Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

Signal Flow

Dante to MADI

The Dante input signal is output from the MADI

[COAXIAL OUT] connector and the [OPTICAL OUT]

connector.

MADI to Dante

The MADI input signal is output from the Dante

[PRIMARY] and [SECONDARY] connectors.

MADI Split

A signal that is input via coaxial or optical connector can

be looped back via the other connector. When doing so,

the signal also goes to the Dante network.

 Settings

• To use a MADI split, turn on MADI DIP switch 3

(DOWN).

• To loop back the input signal from the MADI [COAXIAL

IN] connector to the MADI [OPTICAL OUT] connector,

turn on MADI DIP switch 1 (DOWN).

• To loop back the input signal from the MADI [OPTICAL

IN] connector to the MADI [COAXIAL OUT] connector,

turn off MADI DIP switch 1 (UP).

NOTE

Make sure to change the settings of the DIP switches while the

power to the unit is turned off; otherwise, the ID setting will not

be effective.

3 seconds

RMio64-D Owner’s Manual

Word Clock

About Word Clock

• You can set the word clock source to an external clock

device, the MADI input signal, or the Dante network.

• You can send the word clock from this unit to an

external device via the [WORD CLOCK OUT]

connector.

• You can connect the [SYSTEM LINK OUT] connector

to the AES 2 IN connector on Steinberg Nuendo

SyncStation for high-precision clock sync with

Nuendo.

Selecting a Word Clock

Source

Use the WORD CLOCK [WCLK IN]/[MADI]/[DANTE] key

on the front panel to select the word clock source.

The unit’s clock is synced with the selected word clock

source.

NOTE

• If you select [WCLK IN] or [MADI], the unit is automatically

specified as the “Preferred Master” and “Enable Sync To

External” is set in the Dante network.

• If you select [WCLK IN] or [MADI], when the unit acts as the

clock slave on the Dante network, input to the unit the same

clock as the clock master. You can use Dante Controller

(available from the following website) to check which device

is the current clock master.

http://www.yamahaproaudio.com/

• If the word clock signal from the selected work clock source is

cut off, the unit switches to its internal clock. The internal

clock operates according to the previous word clock, before it

was cut off.

MADI SRC (Sampling

Rate Converter)

MADI SRC allows you to connect a MADI-compatible

device having a different clock than the RMio64-D unit.

• You can connect a Dante network and a MADI-

compatible device that are operating under different

clocks without making any changes to either clock.

• You can output MADI signals with a different word

clock than the MADI input signal.

Setting Examples

NOTE

Output Clock Source in the following block diagram can be

controlled only by remote control.

Using the MADI signal internal clock on the

MADI side, and syncing the unit to the

Dante network:

Using an external clock on the MADI-

compatible devices, and syncing the unit to

the Dante network:

NOTE

The same external clock supplied to MADI-compatible devices

must be input to [WCLK IN FOR SRC] on the unit.

WCLK IN Uses the word clock signal that is input from

the [WORD CLOCK IN] connector on the

rear panel. This indicator flashes if no valid

word clock input is detected.

MADI Uses the word clock of the MADI input

signal. This indicator flashes if no valid word

clock input is detected.

DANTE Uses the word clock from the Dante network.

Word Clock Source Input Clock Source Output Clock Source

DANTE

MADI

WCLK IN

DANTE MADI

Clock

WCLK IN

(FOR SRC)

MADI IN

Same as

Input Clock Source

Same as Word

Clock Source

Signal Processing

Signal

SRC

Word Clock Source Input Clock Source Output Clock Source

DANTE

MADI

WCLK IN

DANTE MADI

Clock

WCLK IN

(FOR SRC)

MADI IN

Same as

Input Clock Source

Same as Word

Clock Source

Signal Processing

Signal

SRC

RMio64-D Owner’s Manual

Syncing the unit to a MADI input signal

NOTE

If the unit acts as the clock slave on the Dante network, input to

the unit the same MADI clock used for the device that is the

clock master. You can use Dante Controller (available from the

following website) to check which device is the current clock

master.

http://www.yamahaproaudio.com/

Using an external clock on MADI-compatible

devices, and syncing the unit to a different

external clock:

NOTE

• The same external clock supplied to MADI-compatible

devices must be input to [WCLK IN FOR SRC] on the unit.

• If the unit acts as the clock slave on the Dante network, input

to the unit the same external clock used for the device that is

the clock master. You can use Dante Controller (available

from the following website) to check which device is the

current clock master.

http://www.yamahaproaudio.com/

Displaying the MADI Input

and Output Signals

The frame format and number of channels for the MADI

input signal or output signal are displayed in the MADI

[STATUS] area.

Use the MADI [STATUS] INPUT/OUTPUT key to switch

between the input signal display and the output signal

display.

Remote Control

You can use the RMio64-D remote control to configure

items that cannot be configured from the unit’s panel,

such as individual settings for MADI SRC input/output

controls and setting the MADI output to a different format

than the MADI input.

NOTE

For the latest information about remote control compatible

devices, refer to the Yamaha Pro Audio website:

http://www.yamahaproaudio.com/

Remote Controllable

Parameters

Control from NUAGE

Workgroup Manager

When RMio64-D is operating in the NUAGE Workgroup,

you can use remote control to configure the RMio64-D

and use direct monitoring functions.

Word Clock Source Input Clock Source Output Clock Source

DANTE

MADI

WCLK IN

DANTE MADI

Clock

WCLK IN

(FOR SRC)

MADI IN

Same as

Input Clock Source

Same as Word

Clock Source

Signal Processing

Signal

SRC

Word Clock Source Input Clock Source Output Clock Source

DANTE

MADI

WCLK IN

DANTE MADI

Clock

WCLK IN

(FOR SRC)

MADI IN

Same as

Input Clock Source

Same as Word

Clock Source

Signal Processing

Signal

SRC

Parameter Description

SRC ON/OFF Turns MADI SRC on or off.

SRC INPUT CLOCK

SOURCE

For selecting the MADI SRC clock

source: the MADI input signal or the

clock input from the WCLK IN FOR

SRC connector.

SRC OUTPUT

CLOCK SOURCE

For selecting the MADI SRC clock

output: the input signal or the unit’s

master clock.

INPUT RATE Displays the frequency when the

MADI input signal is automatically

detected as 44.1 kHz or 48 kHz.

For selecting 1Fs, 2Fs, or 4Fs in

combination with the MADI input

rate.

STATUS INPUT Displays the status of the MADI input

signal.

STATUS OUTPUT Displays the status of the MADI

output signal. You can also make

changes to the frame format and

number of channels for the MADI

output signal.

BNC AES/EBU OUT For selecting the Dante input

channel output from the [SYSTEM

LINK OUT] connector as the AES/

EBU signal.

CLOCK For selecting the source used as the

master clock.

PANEL LOCK Locks the panel to prevent operation

of the unit’s controllers. Default

settings are turned off.

RMio64-D Owner’s Manual

Direct Monitoring

When RMio64-D is operating in the NUAGE Workgroup,

a “direct monitoring” function is available. Direct

monitoring allows you to monitor a MADI signal output

from the RMio64-D to Steinberg Nuendo as direct MADI

output, in the same way as NUAGE I/O.

Direct monitoring provides latency-free monitoring of

signals from audio tracks balanced with the faders in

Nuendo and MADI signals routed to the OUTPUT BUS.

To turn direct monitoring on or off, use the monitoring

button on tracks in Nuendo where the RMio64-D is

routed as input ports.

NOTE

To use direct monitoring, you must activate [Direct Monitoring]

in the Nuendo [Device Setup] menu.

RMio64-D Setup

If there are multiple AIC128-D cards on a Dante network,

specify the AIC128-D unit that is used in Nuendo.

To open the RMio64-D Setup within Nuendo, click

“Devices,” then click “RMio64-D Setup.”

Dante Interface

Select the AIC128-D that is used in Nuendo.

Identify

When you click here, the lamp on the selected

AIC128-D flashes for a few seconds. This function is

convenient for identifying the selected AIC128-D.

Reload

When you click here, choices for the Dante interface

are updated to the latest status.

Troubleshooting

The following is an abbreviated list of frequently asked

questions in the past. Please check it if you run into

Yamaha RMio64 Manuale del proprietario

Marca: Yamaha

Modello: RMio64

Tipo: Manuale del proprietario

Scarica il pdf

rapporto

in altre lingue

English: Yamaha RMio64 Owner's manual
français: Yamaha RMio64 Le manuel du propriétaire
español: Yamaha RMio64 El manual del propietario
Deutsch: Yamaha RMio64 Bedienungsanleitung
русский: Yamaha RMio64 Инструкция по применению
Nederlands: Yamaha RMio64 de handleiding
português: Yamaha RMio64 Manual do proprietário
dansk: Yamaha RMio64 Brugervejledning
čeština: Yamaha RMio64 Návod k obsluze
polski: Yamaha RMio64 Instrukcja obsługi
svenska: Yamaha RMio64 Bruksanvisning
Türkçe: Yamaha RMio64 El kitabı
suomi: Yamaha RMio64 Omistajan opas
română: Yamaha RMio64 Manualul proprietarului

Documenti correlati

Altri documenti

Danfoss ECL 2000 Istruzioni per l'uso