Yamaha DTX540K Manuale utente

Yamaha
Marca
Yamaha
Modello
DTX540K
Categoria
Tamburi musicali
Tipo
Manuale utente

Questo manuale è adatto anche per

DTX540K/DTX520K Assembly Manual
This pamphlet describes the standard procedure for DTX540K/DTX520K assembly.
After assembling the parts and connecting the cords as shown below, you will be ready to turn on the drum trigger module.
• For assembly, you will require four individual packages – an RS500
Rack System, a DTP520C Pad Set, a DTP700P Pad Set*, and a
DTX500 Drum Trigger Module. (*: The DTX520K uses a DTP520P
Pad Set instead.)
• This pamphlet describes how to attach the pads and drum trigger
module to the RS500 Rack System. Before carrying out the proce-
dures described below, ensure that you have correctly assembled
the rack system as described in its assembly manual.
• Although this pamphlet uses illustrations of the DTX540K, the
assembly procedures described also apply to the DTX520K.
Before starting assembly, lay a drum mat (sold separately) on the floor.
Alternatively, before setting up the HH65 Hi-hat Controller and KP65
Kick Pad, you can place the packages' cardboard boxes on the floor to
protect it from damage.
Before using, please read this assembly manual, and use this product in a safe and proper manner.
* Please keep this manual in a safe place for future reference.
* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.
NOTICE
• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,
never place any heavy or sharp objects on the cable. Applying excessive force to the cable may
result in damage to the cable, such as the wires being severed, etc.
• Do not step on or place heavy objects on the product. It may result in damage.
• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,
close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).
Doing so may result in deformation, discoloration, damage or deterioration.
• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or
deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the
product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has
been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to
let the water and detergent come into contact with the cushions used in the product; doing so may
result in deterioration.
* Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at
any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
EN
PRECAUTIONS
Example of standard DTX540K assembly
PCY100
(Cymbal Pad)
XP70
(Tom Pad)
XP70
(Tom Pad)
KP65
(Kick Pad)
XP80
(Snare Pad)
HH65
(Hi-hat Controller)
DTX500 Drum
Trigger Module
PCY100
(Hi-hat Pad)
RS500
(Rack System)
PCY135
(Cymbal Pad)
IMPORTANT
NOTICE
If this symbol is ignored and the equipment is used improperly, fatal
injury to persons or serious damage could occur.
• Do not let small children assemble or set up this product by themselves, or they may be injured.
Always assemble this product with adult supervision.
• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends
may result in injury.
• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends
may result in injury.
• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened
firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may
result in the rack overturning or parts dropping, causing injury.
• Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on
steps may result in the product being unstable and subject to overturning.
• When setting up the product, please pay close attention to the handling and setting of cables.
Carelessly placed cables may cause the user and others to trip and fall.
• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
If this symbol is ignored and the equipment is used improperly,
there is a danger or injury to persons handling the equipment, and
material damage could occur.
• Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your
fingers.
• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting
in injury.
• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums
may drop, causing injury.
Digital Musical Instruments DivisionDigital Musical Instruments Division
©2011 Yamaha Corporation
WW60810 110PO***.*01C0
WARNING
CAUTION
Assemble the RS500 Rack System.
For details, refer to the assembly manual that came with the rack system.
Check the contents of each package.
Mount the pads and the drum trigger module on the rack system.
As described below, mount the pads and the trigger module on the rack system, and then position the kick pad and the hi-hat controller.
1
2
Package 1: DTP520C Package 2: DTP700P (for DTX540K)
PCY135
Cymbal Pad (x1)
PCY100
Cymbal Pad (x2)
HH65
Hi-hat Controller (x1)
Hi-hat holder (x1) Stoppers for the
PCY100 and PCY135
(x3)
Tuning key (x1)
9-channel snake cable (x1)
PCY100, PCY135, and PCY155 Owner’s Manual (x1)
HH65 Owner’s Manual (x1)
Assembly Manual (this pamphlet)
XP80
Snare Pad (x1)
XP70
Tom Pad (x3)
KP65
Kick Pad (x1)
Clamp bolts (x4)
XP70 and XP80 Owner’s Manual (x1)
KP65 Owner’s Manual (x1)
Package 3: DTX500
DTX500 Owner’s Manual (x1)
DTX500 Drum Trigger
Module (x1)
AC power adaptor*
(x1)
Module stand (x1)
Module stand
fastening screws (x2)
Felt for the
PCY135 (x1)
Felts for the
PCY100 (x2)
Cable bands (x10)
Package 2: DTP520P (for DTX520K)
XP80
Snare Pad (x1)
TP65
Tom Pad (x3)
KP65
Kick Pad (x1)
Clamp bolts (x4)
XP70 and XP80 Owner’s Manual (x1)
KP65 Owner’s Manual (x1)
TP65, TP65S, TP100, and TP120SD
Owner’s Manual (x1)
* May not be included depending on your particular area.
Please check with your Yamaha dealer.
3
Mounting the hi-hat holder
1. Remove the drum trigger module clamp a from the left of the rack, together with
the left leg b.
2. Assemble the holder clamp for the hi-hat holder ensuring that it is oriented as
shown in the figure, and then reassemble the left leg b and the drum trigger mod-
ule clamp a.
Drum trigger
module clamp
a
Left leg b
Drum trigger
module clamp a
Left leg b
Holder clamp
Hi-hat holder
Continued on other side
Mounting snare and tom pads
Mounting the snare pad
1. Attach the clamp bolt to the snare pad and provi-
sionally tighten (by 5 or 6 turns).
2. Mount the snare pad on the rack’s clamp rod. As
shown below, ensure that the rod section is fully in-
serted into the pad’s mounting hole, and then fully
tighten the clamp bolt.
3. If necessary, use clamp bolts A to E to adjust the
height and angle of the snare pad. When doing so,
be sure to adjust one bolt at a time (i.e., loosen a
bolt, adjust the pad, and then retighten before loos-
ening another).
Mounting the tom pad
1. As with the snare pad, attach the clamp bolt to each
of the three tom pads and provisionally tighten (by 5
or 6 turns).
2. Mount the three tom pads on the rack’s clamp rods.
As shown below, ensure that the rod section is fully
inserted into each pad’s mounting hole, and then
fully tighten the clamp bolt.
3. If necessary, use clamp bolts A to D to adjust the
height and angle of any of the pads. When doing so,
be sure to adjust one bolt at a time (i.e., loosen a
bolt, adjust the pad, and then retighten before loos-
ening another).
XP80
DTX540K: XP70
DTX520K: TP65
Clamp bolt (to be tightened
in the direction shown)
Snare pad (rear side)
Support plate
Tom pad
Clamp bolt
Insert
Rod section
Clamp rod
Clamp bolt C
Clamp bolt D
Clamp bolt B
Clamp bolt A
Mounting the drum trigger module, cymbal pads, and hi-hat pad
Mounting the drum trigger module
1. Attach the module stand (provided) to the underside
of the drum trigger module using the module stand
fastening screws.
2. Place the module stand inside the holder clamp and
tighten the clamp bolt to secure in position.
Mounting the cymbal and hi-hat pads
1. Using a tuning key, loosen the stopper’s key bolt.
2. Remove the wing nut, the two felt pads, and the bolt
cover from the cymbal holder.
3. Place the stopper on the cymbal holder.
* If the key bolt was not sufficiently loosened in
Step 1 above, it may not be possible to pass the
stopper over the cymbal holder’s shaft. In such a
case, loosen the key bolt as much as possible
without removing it.
4. Replace the bolt cover.
* When assembling the bolt cover, turn until it no
longer rotates.
5. Secure the stopper in place. With the stopper mak-
ing full contact with the bottom surface of the bolt
cover, tighten the stopper’s key bolt using a tuning
key.
6. Place one of the felt pads removed in Step 2 on the
cymbal holder.
7. Mount the pad unit on the cymbal stand. Lower the
pad unit into place with the cymbal holder’s shaft
passing through the central hole of the cup section.
When mounted, the stopper’s pin should rest inside
the pad unit’s smaller hole.
* If you were to play a cymbal pad without the stop-
per’s pin positioned inside the smaller hole, the
pad could rotate, causing the cable to be pulled
out. It is very important, therefore, to ensure that
the stopper is secured as described in Step 5
above.
8. Assemble the felt pad that came with your pad unit.
* The second felt pad removed from the cymbal
holder in Step 2 above is not required for assem-
bly of your pad unit.
9. Tighten the wing nut to secure the pad unit to the
cymbal holder.
Cymbal pad:
PCY100
Drum trigger
module
Hi-hat pad:
PCY100
Cymbal pad:
PCY135
Module stand
fastening screws
Module stand
Drum trigger module
(back side)
Front of
module
Clamp bolt
Drum trigger
module
+
module stand
Insert
Holder clamp
Tuning key
Key bolt
Stopper
Cymbal holder
Felt pads
Bolt cover
Wing nut
Cymbal holder
Stopper
Bolt cover
Cymbal holder
Stopper
Bolt cover
Full contact
Full contact
Bolt cover
[Cymbal pad]
[Hi-hat pad]
Pad unit
Felt pad that came
with pad unit
Cymbal holder
Felt pad
Bolt cover
Pad unit
Stopper
Pin
Wing nut
Stopper’s pin
Smaller
hole
Position the hi-hat controller and kick pad as desired, referring to the standard assembly example on the other side.
Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard
boxes on the floor under the hi-hat controller and kick pad to protect it from damage.
Connect the pads to the drum trigger module.
As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.
Connect the drum trigger module to a power supply.
This completes the assembly procedure.
* For information about tuning the power on/off, checking the actual sound, and other subsequent steps,
refer to the Setting Up section of the owner’s manual that came with your drum trigger module.
Assembling the kick pad
1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the
floor to protect it from scratching.
2. Remove the wing bolts, spring washers, and washers from the kick pad body, and
line up each set nearby in the order in which it was removed.
3. Join the base section to the body as shown right, and then secure it in place by
assembling the wing bolts, spring washers, and washers removed in the previous
step from the base side.
Body
Body
Base
Washer
Spring washer
Wing bolt
4
NOTICE
5
1. Insert the 9-channel snake cable’s straight plugs into the drum trigger module’s
trigger input jacks ([q SNARE] to [i KICK/o] and [HI-HAT CONTROL]).
• If you are using the standard setup, the stickers on each of the snake cable’s
plugs will indicate the name of the corresponding pad.
2. Plug the 9-channel snake cable’s L-shaped plugs into the correct pads.
3. In the case of snare and tom pads, wrap the cables around the cable clips to pre-
vent them from being pulled out.
Excessive bending can damage the pad cables. Ensure, there-
fore, that these cables are not bent at an extreme angle when
wrapped around the clips.
[Drum trigger module’s rear panel]
5678 9
1234
[9-channel
snake cable]
Straight
plugs
L-shaped
plugs
Straight plug names
(as shown on stickers)
SNARE
TOM1
TOM2
TOM3
RIDE
CRASH
HI HAT
KICK
HH CON
DTX500 jack names
1: qSNARE
2: wTOM1/!0
3: eTOM2/!1
4: rTOM3/!2
5: tRIDE
6: yCRASH
7: uHI-HAT
8: iKICK/o
9: HI-HAT CONTROL
HH CON HI HAT CRASH SNARE TOM1 TOM2 TOM3 RIDEKICK
[Locations of pad jacks]
NOTICE
6
1. Ensure that the (Standby/On) button is set to the Standby position, and then con-
nect the AC power adaptor to the DC IN jack on the rear panel.
Hook the power adaptor’s cord around the cord clip to secure it in place.
2. Use the cable bands to bind the cables to the rack as shown on the right. ( )
3. Plug the AC power adaptor into an AC wall socket.
[Drum trigger module’s rear panel]
Cord clip
DC IN jack
  • Page 1 1
  • Page 2 2

Yamaha DTX540K Manuale utente

Yamaha
Marca
Yamaha
Modello
DTX540K
Categoria
Tamburi musicali
Tipo
Manuale utente
Questo manuale è adatto anche per
Scarica il pdf
rapporto

in altre lingue

Documenti correlati