CX-L-410-xx 06067710
DUNSTABZUGSHAUBE
CAPPA D’ ASPIRAZIONE
COOKER HOOD
HOTTE ASPIRANTE
MONTAGE UND GEBRAUCHSANWEISUNG
MANUALE D'INSTALLAZIONE, D'USO E MANUTENZIONE
INSTALLATION, USE AND MAINTENANCE MANUAL
MANUEL D'INSTALLATION, D'EMPLOI ET D'ENTRETIEN
1.
2.
3.
Cm 65 MIN
ASPIRANTE
SUCTION
ABLUFTBETRIEB
ASPIRANTE
FILTRANTE
FILTERING
UMLUFTBETRIEB
FILTRANTE
4.
5.
B
6.
+ 180°
1-2-3-4
1
2
3
4
8.
7.
- 180°
1-2-3-4
1
3
2
4
=
a
b
c d
1.
2.
3.
2
0
0
2
0
0
9.
10.
14.
11.
12.
13.
T0 +
_
a
b
a
b
T
0
+
_
P
• estrarre la lampada difettosa;
• prendere la nuova lampada evitando di toccarla direttamente con le dita, per es. arrotolandola
con carta;
• infilare i due spinotti della lampada nei fori appositi;
• rimontare la cornice del faretto.
9 PULIZIA
Per conservare in buono stato la cappa, pulirla periodicamente seguendo le avvertenze riportate
di seguito.
ATTENZIONE! Assicuratevi che sia esclusa l’alimentazione elettrica.
La sostanza detergente raccomandata è una soluzione di ACQUA e SAPONE LIQUIDO NEUTRO.
E’ molto importante che il sapone liquido sia privo di granuli che possono graffiare la superficie.
La soluzione deve essere prima applicata su un panno morbido e poi a mano si strofina il panno sul
mantello seguendo necessariamente col panno il senso della satinatura (VEDI FIG.14).
E’ fatto assoluto divieto di versare liquidi direttamente sulla cappa.
Il panno deve essere privo di bottoni, chiusure lampo, automatici o altro che possa graffiare la
superficie.
Si vieta l’uso di prodotti aggressivi, granulosi o abrasivi o similari che potrebbero compromettere
l’aspetto superficiale del materiale.
La ditta costruttrice non risponde di danni sia funzionali che estetici causati da una pulizia non
adeguata ai materiali utilizzati od eseguita in modo non corretto.
10 ACCESSORI OPZIONALI
Sono disponibili, venduti separatamente, questi accessori opzionali:
• FILTRI CARBONE.
• SET FILTRANTE.
11 GUASTI
Se la cappa aspirante non risponde al comando togliere tensione alla cappa per circa 1 minuto
estraendo la spina di alimentazione o disinserendo l’interruttore di sicurezza e successivamente
ripristinare il collegamento.
12 CONTRASSEGNO PER DIRETTIVA CEE
Questo apparecchio dispone di contrassegno ai sensi della direttiva europea
2002/96/CE in materia di apparecchi elettrici ed elettronici (waste electrical and
electronic equipment (WEEE).
Questa direttiva definisce le norme per la raccolta ed il riciclaggio degli
apparecchi dismessi valide su tutto il territorio dell’ Unione Europea.
Il simbolo a lato sul prodotto o sulla confezione indica che il prodotto non
deve essere considerato come un normale rifiuto domestico, ma deve
essere portato nel punto di raccolta appropriato per il riciclaggio di apparecchiature
elettriche ed elettroniche. Provvedendo a smaltire questo prodotto in questo modo
appropriato, si contribuisce a evitare potenziali conseguenze negative per l’ ambiente e per
la salute, che potrebbero derivare da uno smaltimento inadeguato del prodotto. Per
informazioni piu’ dettagliate sul riciclaggio di questo prodotto, contattare l’ ufficio comunale,
il servizio locale di smaltimento rifiuti, o il negozio in cui è stato acquistato il prodotto.
Per la Svizzera :
Dove dismettere i vecchi apparecchi ?? O dove sono acquistati i nuovi o consegnarli ai
punti di raccolta S.EN. S. o ai riciclatori ufficiali S.EN.S.
La lista dei punti di raccolta ufficiali S.EN.S si puo’ trovare sotto : www.sens.ch
COOKER HOOD
1 GENERAL
The model you have selected is a decorative suction cooker hood which can also work as filtering
hood.
A SUCTION HOOD extracts air, fumes and vapours from the inside environment and then expels
them outside. It is not necessary to use carbon filters for purifying.
A FILTERING HOOD extracts air, fumes and vapours from the inside environment, purifies them
by means of carbon filters and then emits the purified air into the same environment. In this case,
the use of carbon filters is absolutely necessary (see FIG. 1).
Carbon filters are available separately and can be purchased as optional accessories (see
OPTIONAL ACCESSORIES).
2 BEFORE MOUNTING
Before mounting you should be aware of:
2.1) the power rating of the cooker:
- if it is below or equal to 7 kw (kilowatt), the hood should be mounted so that the
minimum distance between it and the top of the cooker is not less than 65 cms;
- if it is above 7 kw (kilowatt), the manufacturer recommends that the distance be
increased by 2,5 cms for each extra KW delivered by the cooker top.
DISTANCE in cms = 65 + 2,5 x (POWER in KW - 7)].
WARNING! If the user decides to install the hood at distances
below 65 cms, the manufacturer declines any responsibility for eventual damages
caused by the hood due to strong heat or damages to property or persons etc.
caused directly or indirectly by any type of malfunctioning breakdown or possible fire
(see FIG. 2).
2.2) arrange for a socket outlet or standard connection to the electric mains;
2.3) if the hood is used as a suction hood, it is necessary to make a hole towards the
outside (i.e. in the open air) for the scavenging of the fumes.
WARNING! It is absolutely forbidden for the user to connect the air
discharge of the hood, when used as a suction hood, to boiler chimneys, gas, fume or
vapour scavenging chimneys or any other duct, even only ventilation ducts, which
have been used or will be used for other devices. Moreover, it is not permitted to
connect the scavenging pipe for fumes in other adjacent rooms or wellholes, or pipes
for fire-fighting devices.
In any case it is necessary to respect all norms concerning scavenging of the air.
Any user who does not adhere to these instructions is risking his own life and the lives of
others. In this case, the manufacturer declines any responsibility (see FIG. 3).
2.4) If the hood is used as a suction hood, it is necessary for qualified personnel to make a
hole for ventilation on the outside wall.
If the cooker is gas, it is not advisable to use the hood at the same time as fireplaces,
furnaces, gas or other fuel stoves, or water heaters which burn up oxygen from the
environment in order to function, and in any case depression in the cooker area must be
below 4 Pa (0.04 mbar) and the room must be sufficiently aired.
If in doubt, national and international standards precisely indicate the rules for the state
of art installation of gas systems and for environment air change, to avoid the possibility
of incomplete combustions with the risk of poisonous fumes being emitted (see FIG. 4).
2.5) If the hood is to be used as a filtering hood, it is necessary to purchase carbon filters
(see ACCESSORIES).
3 MOUNTING INSTRUCTIONS
3.1 DISMANTLING AND RE-POSITIONING OF THE GREASE FILTERS
To mount the hood or insert the carbon filters, it is necessary to gain access to the inside,
therefore the grease filters should be removed.
Attention: some cooker hoods are equipped with blind grease filters for side suction that cover the
real grease filters; in these cases before removing the grease filters it is necessary to take away
the blind filters by gripping them from the side and pulling them downwards. (Fig. 5).
TO EXTRACT a grease-filter (see direction of arrow in FIG. 5):
• pull the lever and take the grease filter out pulling it downwards.
TO RE-POSITION the grease-filter (SEE FIG. 5 opposite direction to the arrow):
• insert the back side of the grease filter into its groove;
• pull the lever downwards and insert the front part of the filter;
• release the lever and make sure that the pin of the handle enters into its hole.
3.2 FITTING AND REMOVAL OF EVENTUAL CARBON FILTERS
If you wish to use the hood as a filtering hood, it is necessary to fit the carbon filters.
The carbon filters which contain activated carbon ARE OPTIONAL, and can be bought separately.
We have 2 different kinds of carbon filters. Once you have dismantled them, it is possible to
recognize the kind of filter used in the hood (see FIG. 6).
In case the mounted filter is the one shown in FIG. 6a, follow the following procedure for
mounting:
• pay attention to the shape of the joints;
• insert the back side into its groove;
• lift the front side of the carbon filter, until it is blocked in position;
• clamp the filter by rotating the 2 knobs at 90°.
To remove a carbon filter proceed as follows: (see FIG. 6A, opposite direction of arrows):
• rotate the two knobs at 90°;
• pull the front side of the filters downwards;
• fully extract, by removing the back of the filter from the groove.
In case the carbon filters used are the ones shown in Fig. 6b, (pair of filters), proceed as
follows for mounting:
• grip the external part of the filter (the convex one);
• lay the filter on the side of the motor so that the joints in alu can enter the grooves;
• rotate the filter 60 ° in the direction shown by the arrow;
• to be sure that the filter is correctly installed, try to move this from the motor to the outside. If
it does not move, it means it has been correctly fitted.
Repeat the above for the other filter
To remove both carbon filters proceed as follows for both of them (see FIG.6b, DIRECTION
OPPOSITE TO THE ARROW):
• grasp the external part of the filter;
• rotate the filter 60° in the direction opposite to the one shown in the picture, the carbon filter
will release the joint in alu;
• grasp the filter and pull this far from its housing;
• repeat the above for the other filter.
If you have a wall cooker hood (FIG.7), see par. 3.3.
If you have a island cooker hood with external chimney (FIG.10), see par 3.4.
3.3 MOUNTING THE HOOD TO THE WALL
3.3.1 PREPARATION OF THE DECORATIVE CHIMNEY ATTACHMENTS
To mount the decorative chimney, it is necessary to arrange for a ceiling attachment.
The support bracket is of such a shape that it can be fixed to the ceiling or the side wall (SEE
FIG. 7).
To fix the bracket, proceed as follows:
• decide exactly where on the ceiling (or on the wall), the support bracket for the chimney is to
be fitted;
• make support and safety fixing holes with a drill;
• fit the screw plugs in the holes;
• fit the screws in the plateholes and in the plugs;
• tighten the screws with a screwdriver.
3.3.2 FIXING TO THE WALL
To fix the hood to the wall, proceed as follows:
• based on the technical drawing, mark the position of the support and safety fixing holes on the
wall with a pencil, in such a way that the base of the hood is at the distance from the cooker
hob, as indicated in par. (2.1) and that it is horizontal. Mark the position of the holes with a
pencil making a small cross on the wall.
• drill the support and safety fixing holes in the positions marked;
• fit the metal hooks to the support holes (see FIG.8) complete with plug and screws,
completely inserting the plastic plug and keeping the curved part on the outside and facing
downwards; in the safety fixing holes only insert the plastic plug;
• tighten the support screws;
• rest the back of the hood on the wall and insert the hooks into the corresponding slots;
• make sure the hood is stable;
• holding the cross notched screwdriver in your hand; slowly tighten the horizontal alignment
screws one at a time, until the hood is perfectly horizontal above the cooker hob. The use of a
level will help in this operation;
• insert the screws into the safety holes;
• tighten the safety holes with the screwdriver.
3.3.3 MOUNTING OF THE SCAVENGING PIPE
If the hood is to be used as a suction hood, to apply the pipe proceed as follows:
• measure the distance to be covered by the pipe and obtain parts of the right size;
• insert the hood outlet mouthpiece into the pipe and block it;
• connect the lengths of pipe up to the hole towards the outside;
• connect the pipe to the end which goes outside;
• make electrical connection (see par.4).
3.3.4 MOUNTING OF THE DECORATIVE CHIMNEY
The decorative chimney shown in FIG. 7 is composed of 2 parts of metal sheet which slide one
inside the other. To mount the chimney please proceed as follows:
• the 2 parts of the chimney are mounted as shown in FIG. 7;
• position the base part of the chimney with holes matching the ones on the hood;
• insert small screws on the bottom of the chimey and fix them;
• let the telescopic part of the chimney slide to the height necessary to touch the ceiling and
come into contact with the chimney bracket;
• tighten the screws on the chimney bracket to the ceiling.
3.4 MOUNTING THE ISLAND COOKER HOOD WITH EXTERNAL CHIMNEY
The island cooker hood is intended to be mounted either directly on the kitchen ceiling or onto a
stable suspended false ceiling structure.
Check that the minimum distance between the bottom of the hood and the upper part of the hob
is in conformity with indications in par. 2.1.
• Mark the centre of the position on the ceiling at which the hood will be mounted;
• according to the technical drawing, mark on the ceiling the position of the fixing points;
• using a drill suitable for building materials, make the fixing holes and insert plugs so that they
are flush with the ceiling;
• Mount the support structure to the ceiling FIG.9;
• Fix the upper chimney to the support structure FIG.10, by means of 2 screws;
• insert the lower chimney to the exterior of the upper chimney, blocking it by strong tape in a
way that the chimney cannot possibly fall FIG.10;
• insert the cooker hood in the support frame and screw it at the established height. FIG.10. If
the hood is not properly aligned, after loosening the 4 screws on the ceiling, it can be rotated
in the longitudinal holes: finally tighten the screws;
• connect the pipe;
• connect the hood to the electricity supply (par. 4);
• push down the lower part of the chimney with extreme caution so that no scratches can be
produced on the upper chimney.
3.5 GENERAL WARNING
The pipe must be heat, flame and corrosionproof. The manufacturer strongly advises against the
use of reducers or pipes with different diameter to the hood outlet pipe, and pipes made of flexible
aluminium (called “corrugated pipe”) because performance is diminished and noise level
increased.
The end part of the pipe, on the outside of the hole on the wall, must be of such a shape to avoid
rain, gusts of wind or other foreign bodies getting into the pipe. Should there be any doubt,
contact anyone specialising in the installation of gas or ventilation system.
4 ELECTRICAL CONNECTION
4.1 WARNING
The electrical connection can only be carried out by qualified professional personnel, using
standard material and state of the art installation methods. The manufacturer declines any
responsibility for installations carried out by unskilled persons and for installations which are not in
conformity with the standard norms concerning electrical safety (both concerning methods and
materials).
4.2 ELECTRICAL TECHNICAL DATA
The electrical technical data are visible inside the hood after the removal of the grease filters.
4.3 CONNECTION TO THE POWER SUPPLY
The flexible feed cable supplied is already connected internally and emerges from the hood near
the air outlet duct.
It is possible to effect two types of electric installation:
• fixed installation;
• installation by means of plug on a socket.
4.4 BEFORE ELECTRICAL INSTALLATION
Before connection you must:
• check that the electrical data indicated are in conformity with the main voltage and frequency
values of the building where the hood is to be installed;
• check that the building is fitted with electric safety systems to protect against short circuits
and electric shock systems, according to the laws in force;
• install an electric socket (or connection point) with a bipolar switch, which has contacts with
an opening of at least 3 mms;
• if it is intended to install the hood with a plug, it is necessary that you have access to the plug.
• always turn off the main voltage supply by means of the bipolar switch before connecting and
switch on again only when connections have been completed, tested and are safe.
5 PRECAUTIONS TO BE TAKEN IF REPAIRS ARE TO BE CARRIED OUT
Repairs, including the replacement of the feed cable if necessary, are to be carried out only by
qualified personnel, using standard methods, instruments and materials. Any repairs carried out
by others could prove to be dangerous and could be a fire risk.
6 INSTRUCTIONS FOR USE and PRECAUTIONS
Before using for the first time, ensure that all the points in the previous paragraphs have been
complied with. MOREOVER remember:
• not to cook “flambé” dishes, avoid flames directly underneath the hood;
• to avoid leaving on any hot plates which generate strong free flames underneath the
hood;
• to avoid any strong flames being issued from under saucepans at the sides;
• when frying, not to allow oil to splash or overheat in the pan, as this is a fire risk;
• before any cleaning or maintenance operation, disconnect the hood from the main
supply, by means of the main switch or the bipolar switch or by removing the plug;
• if other gas equipment or equipment which consumes oxygen from the environment is
used, ventilation must be sufficient. For safe ventilation, maximum depression in the
room should not exceed 4 Pa (0,04 mbar) and there must be a hole on the outside
facing wall (suitably positioned and dimensioned);
• never use the hood without the grease filters;
• keep the grease filters clean, taking into account the recommended cleaning
suggestions;
• replace the carbon filters (if the hood is used as a filtering hood), as indicated;
• turn on the hood motor before you start cooking;
• turn off the hood motor about 10 minutes after you have finished cooking;
• do not use the hood to suction gas, fumes, vapours or other substances different from
the normal fumes in the kitchen.
7 FUNCTION AND USE
In FIG. 11 you see the 2 different kinds of controls:
FIG.11a: soft touch control with display; see par. 7.1.1.
FIG.11b: soft touch control with led points and push buttons screenprinted on s/steel. See
par. 7.2.1.
7.1.1 SOFT TOUCH CONTROL WITH DISPLAY AND BUTTONS (FIG. 11a)
The activated functions are listed as follows:
LIGHTS: to switch the lights on or off; (pressure inf. to 1 second);
O MOTOR OFF: turn the motor off;
T TIMER: if pressed when the hood is already functioning with one
of the pre-established speeds, timing is activated, that is a count down of 15 minutes,
after which the motor stops. During this time the display indicates the speed number and
the point led flashes;
- reduces the speed of the motor;
+ increases the speed of the motor;
P INTENSIVE SPEED: the intensive speed is the highest motor speed. It is
automatically excluded after 5 minutes and the hood goes back to the 2
rd
speed.
DISPLAY MEANING OF THE SYMBOLS:
STAND_BY: The motor of the hood is off;
..... first, second , ….speed;
intensive speed activated;
flashing led point: the timer is in action;
(FLASHING F LETTER) grease-filters should be cleaned;
only in case of filtering hood (flashing C letter) carbon filters should be
replaced.
7.1.2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTERS
The electronic controls with display allow automatic control of the grease filters and the carbon
filters (only when the hood is used in the filtering version), so that the user does not have to
remember when maintenance was last carried out.
When the metallic grease filters have to be cleaned, the letter F on the display will flash.
When the carbon filters have to be replaced, the letter C on the display will flash.
It is possible to consult the electronic system concerning how clean the grease filters are and how
worn the carbon filters are, as follows: stop the motor and ...
… to find out how clean the fat filters are, press the O and
- buttons at the same time. On the
display, a number between 0 and 9 will appear, the smaller the number, the dirtier the filter is;
… to find out how worn the carbon filters are, press the buttons O and
+. On the display, a
number between 0 and 9 will appear, the smaller the number, the more worn the filter is.
7.1.3 TO PUT THE GREASE AND/OR CARBON FILTER CONTROL BACK TO ZERO:
• stop the motor (stop position);
• push the push-buttons 0 (zero) and T (timer) at the same time for a few seconds. This symbol
appears
and a “bip“ is issued.
7.1.4 SETTING THE SUCTION /FILTERING USE OF THE HOOD
The hood is delivered standard for suction use (only with flashing F letter). If you wish to use it in
the filtering version (F and C flashing) proceed as follows:
press the buttons
and T on the display for about 5 seconds, the following symbol will
appear followed by a 0.
• At each pressure of the Light Button, it is possible to change the value shown from the O
(suction function), to 1 (filtering function) and viceversa.
• Press the O button (zero) to confirm the choice effected in the previous point.
7.2.1 SOFT TOUCH CONTROLS WITH PUSH BUTTONS SCREENPRINTED ON S/STEEL
(FIG.11b)
WARNING !
To activate the functions connected to these push buttons, it is necessary to
apply a little pressure just lightly and for a short time. If pressure is too lengthy on the
push buttons the connected functions are not activated.
The functions activated by the push buttons are as follows:
LIGHTS: switch the lights on and off;
O MOTOR OFF: turn the motor off;
- reduces the motor speed;
+ increases the motor speed;
TIMER: if pressed when the hood is already functioning with 1st, 2nd, 3rd or 4th
speed, the led point connected with the selected speed, starts to flash for 10 minutes,
after which motor automatically stops.
MEANING OF THE LED POINTS: if the leds connected with the speeds are flashing, there is a
timing running.
1st Speed;
2nd Speed;
3rd Speed;
4th Speed;
5th Speed; led point is flashing;
6th Speed; led point is flashing.
5th and 6th Speed must be used just for short periods as the hood is taking in a big quantity of air
so after 10 minutes the motor is automatically reset to the 3rd speed.
7.2.2 AUTOMATIC CONTROL OF GREASE AND CARBON FILTER
the electronic controls with led points allow automatic control of the grease filters and carbon
filters (only in case the hood is used in filtering version) so that the user does not have to
remember when maintenance was last carried out.
When the grease filters require cleaning, an
acoustic signal is issued for some seconds
and the led point above the timer push
button keeps on flashing.
When the carbon filters need replacing, an
acoustic signal is issued for some seconds
and the led point above the light push
button keeps on flashing.
7.2.3. TO PUT THE GREASE AND CARBON FILTERS CONTROL BACK TO ZERO
To put the grease filter counter back to zero you must:
• stop the motor;
• press the timer push button twice in succession, until you hear the acoustic signal.
To confirm reset the led point stops flashing.
To put the carbon filter counter back to zero you must:
• stop the motor;
• press the light push button twice in succession until you hear the acoustic signal.
To confirm reset, the led point stops flashing.
ATTENTION: The light push button does not switch on/off the lights until you hear acoustic
signal.
7.2.4 SETTING OF THE SUCTION/FILTERING USE OF THE HOOD
The hood is delivered standard for suction use.
If you wish to use the hood in the filtering version, proceed as follows:
• disconnect hood from electricity and then reconnect this to electricity;
• the led-point of the light push button will flash for approx. 10 seconds. During this time press
the light push button 3 times. Three acoustic signals are issued to point out the new setting.
ATTENTION: during the suction/filtering setting phase no function can be activated.
If the hood is set for suction, when connected the led point over the LIGHT Push Button is
flashing. If the hood is set for filtering, when connected the led point over the
TIMER Push Button is flashing.
8 MAINTENANCE
8.1 CLEANING OF GREASE FILTERS
The metallic grease filters are positioned on the bottom of the hood and are used to contain any
grease which is normally emitted in cooking fumes, thereby impeding the deterioration of the
motor.
For washing by hand, use hot water and soap; this can be done by hand brushing vigorously
several times and then rinsing under the tap.
After washing, the grease filters should be dried and re-fitted correctly.
It is possible that after washing the filter colour changes slightly.
In this paragraph guide lines are given, which should be complied with.
WARNING !
We recommend washing grease filters after 50-100 hours of use of the hob. If grease
filters are dirty, motor can take in just a small quantity of air and performance is reduced;
• The grease which accumulates on dirty filters is easily inflammable and CAN CAUSE
FIRES, if not eliminated by periodic washes.
The manufacturer declines any responsibility for fires caused by poor maintenance of
the grease filters.
8.2 CARBON FILTERS
The carbon filters at the suction outlet of the motor, are used to retain the odours of kitchen
fumes. It is not necessary to use carbon filters, if the hood is used for suction use.
The use of carbon filters is necessary if you use the hood as filtering.
WARNING:
WE RECOMMEND REPLACING CARBON FILTERS AFTER APPROX. 200-300 HOURS OF
USE OF THE HOB.
CARBON FILTERS CANNOT BE WASHED OR RE-CYCLED. THEY MUST BE REPLACED
WHEN THEY WEAR OUT.
Carbon Filters do not guarantee the interchange of oxygen in the air.
To ensure correct ventilation and air interchange in the kitchen, national and international
regulations exist, which should be respected.
The manufacturer denies any responsibility for fires caused by failure to replace the
carbon filters.
8.3 REPLACEMENT OF LAMPS
WARNING! Always replace the lamps with lamps which have the same electrical
characteristics (see TECHNICAL DATA). Before replacing the lamps, make sure that they are cold
and that power has been completely turned off.
The halogen lamps used can be adjustable or flat and fixed.
To replace a dicroic bulb with an adjustable lamp (FIG.12) proceed as follows:
• take out the circular spring in contact with the glass, grasping the edges;
• take out the faulty bulb and replace it with a new one;
• lift the lamp positioning it into its seat and re-insert the circular spring.
To replace a halogen lamp with a fixed lamp proceed as follows (see FIG.13):
• dismantle the lamp frame by means of a screwdriver, making sure that the glass does not fall;
• take the faulty lamp out;
• take a new lamp, avoid touching it directly with your fingers, i.e. wrap it in paper;
• insert the two gudgeons into the holes;
• mount back the lamp frame.
9 CLEANING
To preserve the hood in good condition, clean this periodically following the advice given as
follows.
WARNING! Make sure that power has been completely turned off.
The detergent solution recommended is a combination of WATER and NEUTRAL LIQUID
SOAP. It is of vital importance that the liquid soap should not contain any grains which could
scratch the surface.
The solution should be applied first onto a soft cloth which is then rubbed over the shell. It is
important to follow the pattern of the satin finish with the cloth (see FIG.14).
IT IS ABSOLUTELY FORBIDDEN TO POUR LIQUIDS DIRECTLY ONTO THE HOOD.
The cloth used should not have any buttons, zips, fasteners or anything else which could
scratch the surface.
The use of harsh abrasive or granular products, petrol, spirits or similar products which could
damage the surface of the materiall, is severely forbidden.
The manufacturer will not be responsible for any damages either functional or to the
appearance of the hood, caused by cleaning operations carried out using unsuitable products
or unsuitable methods.
10 ACCESSORIES
The following optional accesories are available and are sold separately:
• CARBON FILTERS (SEE FIG.6)
• FILTERING SET
11 TROUBLESHOOTING
If the cooker hood is not responding to the controlS, disconnect electricity for about 1 minute,
taking the plug out or disconnecting the main electricity supply, then reconnect.
12 EUROPEAN DIRECTIVE MARK
This appliance is marked according to the European directive 2002/96/EC on
Waste Electrical and Electronic Equipment (WEEE). This norm is the frame of a
European-wide validity of return and recycling of Waste Electrical and Electronic
Equipment.
The symbol on the product or on its packaging indicates that this product may not
be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the environment
and human health, which could otherwise be caused by inappropriate waste handling of this
product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
For Switzerland : Where to give old appliances ?? Either where you buy the new ones, or delivery
them to the official S.EN.S collection points or S.EN.S recyclers. List of the official
S.EN.S collection points you find under www.sens.ch
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
Electrolux EFC9830.1 Manuale utente
- Tipo
- Manuale utente
in altre lingue
- English: Electrolux EFC9830.1 User manual
