CIARRA CBCB6736G-OW Manuale utente

ENGLISH

INSTALLATION AND USER'S MANUAL

Page

1-23

DEUTSCH

BENUTZERHANDBUCH&INSTALLATION

SANLEITUNG

Seite

24-46

FRANÇAIS

MANUEL DE L’UTILISATEUR ET

D’INSTALLATION

Page

47-69

ITALIANO

INSTALLAZIONE E MANUALE

DELL’UTENTE

Pagina

70-92

ESPAÑOL

MANUAL DE USUARIO E

INSTRUCCIONES DE INSTALACIÓN

Página

93-115

NEDERLANDS

INSTALLATIE- EN

GEBRUIKERSHANDLEIDING

Pagina

116-138

SVENSKA

INSTALLATION- OCH

BRUKSANVISNING

Sida

139-161

Phone Scaning, Hood Installing

www.ciarra.store

EN

Dear customer:

Congratulations on purchasing this device. This instruction manual is designed

to provide you with all required instructions related to the installation, use and

maintenance of the appliance. In order to operate the unit correctly and safety,

please read this instruction manual carefully before installation and usage.

The cooker hood use high quality materials, and is made with a streamlined

design. Equipped with large power electric motor and centrifugal fan, it also

provides strong suction power, low noise operation, non-stick grease filter and

easy assembly installation.

Scan the QR code to get access to contact CIARRA Amazon Service if you

have any question.

Scan to contact CIARRA Amazon Service

UK DE FR

IT ES NL

1

E-mail: info@ciarra.store

SE PL

EN

CONTENTS

Safety------------------------------------------------------------3-4

Specifications---------------------------------------------------5

Components-----------------------------------------------------5

Installation---------------------------------------------------6-13

Prepare for Installation---------------------------------------6

Recommended Tools for Installation---------------------7

Install the Hood--------------------------------------------8-12

Activated Carbon Filter Installation----------------------13

Operation---------------------------------------------------14-18

Cleaning and Maintenance----------------------------19-21

Motor

Grease Filter

Fan Blade

Activated Carbon Filter

Stainless Steel Cleaning

Painted Finish Cleaning

Bulb Replacement

Troubleshooting-----------------------------------------------22

Environmental Protection----------------------------------23

2

EN

Safety

! WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

◼ Use this unit only in the manner intended by the manufacturer. If

you have questions, contact the manufacturer at the address or

telephone number listed in the warranty.

◼ Before servicing or cleaning unit, switch power off at service panel

and lock the service disconnecting means to prevent power from

being switched on accidentally. When the service disconnecting

means cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

◼ Installation work and electrical wiring must be done by a qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction.

◼ Sufficient air is needed for proper combustion and exhausting of

gases through the flue (chimney) of fuel burning equipment to

prevent back drafting.

◼ When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

◼ Ducted fans must always be vented to the outdoors.

◼ Do not use this unit with any additional solid-state speed control

device.

◼ This unit must be grounded.

◼ When applicable local regulations comprise more restrictive

installation and/or certification requirements, the aforementioned

requirements prevail on those of this document and the installer

agrees to conform to these at his own expense.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1) Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

2) Always turn hood ON when cooking at high heat or when flam

being food.

3) Clean ventilating fan frequently. Grease should not be allowed to

accumulate on fan, filters or in exhaust ducts.

4) Use proper pan size. Always use cookware appropriate for the size

of the surface element.

3

EN

Safety

! WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT

OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal

tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,

EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN — You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels — This

could cause a violent steam explosion.

4. Use an extinguisher ONLY if:

a) You own a Class ABC extinguisher and you know how to

operate it.

b) The fire is small and contained in the area where it started.

c) The fire department has been called.

d) You can fight the fire with your back to an exit.

! CAUTION

◼ For indoor use only.

◼ For general ventilating use only. Do not use to exhaust hazardous or

explosive materials and vapors.

◼ To avoid motor bearing damage and noisy and/or unbalanced fan blade,

keep drywall spray, construction dust, etc. off range hood.

◼ Your hood motor has a thermal overload which will automatically shut off

the motor if it becomes overheated. The motor will restart when it cools

down. If the motor continues to shut off and restart, have the hood

serviced.

◼ Always follows the cooking equipment manufacturer’s requirements

regarding the ventilation needs.

◼ To reduce the risk of fire and to properly exhaust air, be sure to duct air

outside — Do not exhaust air into spaces within walls or ceiling or into

attics, crawl space or garage.

◼ When installing, servicing or cleaning the unit, it is recommended to wear

safety glasses and gloves.

◼ Please read specification label on product for further information and

requirements.

4

EN

Specifications

Voltage

220V-240V~ 50Hz

Power of Motor

1 x 80W

Power of lamps

1x1W+2.5W(UV)

Cable length

1.5M

Appliance Dimension

595*330*810~1190mm

(W x D x H)

Note: The manufacturer reserves the right to change any

technological improvement or modification without prior notice.

Components

5

EN

Installation

Prepare for installation:

a) If you have an outlet to the outside, your cooker hood can be connected as

below picture by means of an extraction duct (enamel, aluminum, flexible

pipe or inflammable material with an interior diameter of 150mm).

Choose a straight, short duct run to allow the hood to perform most

efficiently. Long duct runs, elbows and transitions will reduce the

performance of the hood. Use as few of them as possible. When possible,

use at least 2 foots straight runs before any turns. Larger ductwork may

be required for best performance with longer duct runs.

b) Before installation, turn the unit off and unplug it from the outlet.

c) The cooker hood should be placed at a distance of 65~75cm above the

cooking plane for best effect.

6

EN

Installation

Recommended Tools for Installation

• Measuring tape

• Phillips screwdriver no. 2

• Flat blade screwdriver (to open knockout holes)

• Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut

electrical access hole)

• Wood shims (2) and wood screws (4) (required for standard installation to

framed cabinet)

• Saw (to cut holes for ducted application)

• Sheet metal shears (ducted installation only, for duct adjustment)

• Pliers (ducted installation only, for duct adjustment)

• Metal foil duct tape (for ducted applications)

• Scissors (to cut metal foil duct tape)

• Pencil

• Wire stripper

• Strain relief, 1/2” diameter (to secure house wiring cable to the hood)

CAUTION: Before proceeding to the installation, check the contents of

the box. If items are missing or damaged, contact the manufacturer.

Observe all governing codes and ordinances. Have a qualified

technician install the range hood. It is the installer’s responsibility to

comply with installation clearances specified on the model/serial rating

plate. The manufacturer declines all responsibility for improper

installation and does not accept responsibility for appliance warranty in

the event of damage caused by incorrect installation.

7

EN

Installation

Attention: Observe the warning in the instruction sheet concerning the

operation of the appliance when air is discharged from the room.

When the range hood and appliance supplied with energy other than electricity

are simultaneously in operation, the negative pressure in the room must be not

exceed 4 Pa (4×10-5 Bar).

Install the Hood（VENT OUTSIDE）:

1) If present, remove all protective poly film from the hood and/or parts.

2) Below is the hole drilling installation drawing:

3) According to the 1:1 hole drawing, Drill 3*Ø8mm holes to accommodate

the bracket. Screw and tighten the bracket onto the wall with the screws &

Wall plugs provided.

8

EN

Installation

4) Hang the cooker hood onto the wall bracket.

5) Open the glass panel, take out the grease filter, find the two positioning

holes inside the case in the figure, mark with pen respectively, and then

take down the cooker hood.

9

EN

Installation

6) Drill two 8mm holes in the marked position on the wall with an electric drill,

and then put the wall plug in.

7) Hang the cooker hood on the wall bracket again. After that, use two 4 *

30mm screws to lock the corresponding positioning in the figure.

8) The lower chimney bracket is used to fix the upper decorative chimney and

lower decorative chimney.

Use 2pcs ST4x8mm screws to attach lower and upper chimney together.

Before attaching the bracket to the chimney, decide the location of lower

chimney bracket fixing holes for fixing the lower chimney bracket in the

later step.

Do not fasten screws too much, make sure upper decorative chimney can

be telescopically adjusted after assembled.

10

EN

Installation

9) Put the Aluminum Flex Pipe on the air outlet of the cooker hood and fix the

tube with the Cable Ties.

10) Put the chimney on the cooker hood. Fix the lower chimney bracket on the

wall by 2 screws (4mm x30mm).

11

EN

Installation

11) Then pulling out the upper chimney upwards to the target height. Adjust to

reach the height required.

12) Fix the upper chimney on the upper chimney bracket by 2 screws (4x8mm).

Then fix the upper chimney bracket on the wall. Before fixing the bracket

on the wall, you can decide the upper chimney bracket fixing holes for

installation.

13) Fix the lower chimney with 2 pcs of ST4x8mm screws on the cooker hood.

NOTE:

➢ Connect ductwork to hood and use metal foil duct tape to make joints

secure and air-tight.

➢ Make sure the damper assembly (or round duct plate) enters the ductwork

and that the damper opens and closes freely.

12

EN

Installation

Activated Carbon Filter Installation（VENT INSIDE）:

If you do not have an outlet to the outside, exhaust pipe is not required and the

installation is similar to the one shown in section “Installation (Vent outside)”

1. Activated carbon filter can be used to trap odors.

In order to install the activated carbon filter, the grease filter should be

detached first (The front panel opens at an Angle < 90°). Press the lock

and pull it downward.

2. Plug the activated carbon filter into the blower as shown and turn it in

anti-clockwise direction.

3. Install the grease filter. If replacement, please turn it in clockwise direction.

NOTE:

➢ Make sure the filter is securely locked. Otherwise, it would loosen and

cause dangerous.

➢ When activated carbon filter attached, the suction power will be lower.

➢ The activated carbon filter should be changed every 3 months depending

on the conditions of us.

13

EN

Operation

Always turn your hood on before you begin cooking to establish an air

flow in the kitchen.

Electronic button

Operate the hood as follows:

STANDBY MODE

After plug in, When the buzzer makes a sound and all the indicator lights are

on for 1S then go out, the hood enters the standby mode. The [1] button

indicator light continues to flash regularly. If there is no operation for 60s, the

hood enters into sleep mode; If you need to operate, press any button briefly to

start up the cooker hood.

Press the [1] button for more than 1S, the hood will enter the working mode.

Press the corresponding function button to start the corresponding function

mode, and press again to turn off the corresponding function mode.

Low Speed button

It is suitable for simmering and cooking which do not make much steam.

Medium Speed button

Airflow speed is ideally for ventilation in standard cooking operation.

High Speed button

When high density of smoke or steam produced, press high-speed button for

highest effective ventilation.

Booster button

Depress this button to enter into highest speed.

Light button

When lights are OFF, push once on this button to turn ON the lights. Push this

button again to turn OFF the lights.

14

EN

Operation

The function of UV lamp

CAUTION:

1. UV lamp can not be touched by naked hands and can not be taken off.

2. When the front panel is open, UV lamp can not be turned on.

This appliance contains a UV emitter, Don't look straight at the light to

prevent eyes damage.

3. The UV lamp may start slowly in low temperature environment. Please wait

patiently. The lamp will return to normal operation after the temperature

rises.

UV lamp is mainly used for sterilization and disinfection. It is recommended to

turn on the UV lamp when the cooker hood is working (especially when using

the activated carbon internal circulation mode).

In the working mode, long press the [3] button and [B] button at the same time

to turn on UV lamp, and the light button indicator light starts to flash;

Long press the [3] button and [B] button at the same time to turn off the UV

lamp, and the light button indicator will stop flashing.

15

Smart Life APP

Download and Intallation of Smart Life APP

1. You must use Android phone or iPhone to download and use this APP.

2. Search “Smart Life” in the Googel Play store for Android or IOS App Store

to download and install the APP.

Cooker Hood and Smart Life APP pairing

1. When you log in to Smart Life APP for the first time, you need to create a

new account. When creating a new account, follow the app prompts to

register.

2. If you already have an account, you can use existing account to log in.

3. After logging in successfully, follow the steps below to connect the cooker

hood (the operating procedures of Android and IOS systems are the same)

Video Guide

EN

Operation

1. Open the smart life

app, Click Add Device.

2. Choose kitchen

appliances from the

menu bar on the left.

3. Choose kitchen hood.

4. Enter WiFi hotspot and

password, then click

Confirm.

5. When enter this

interface, choose AP

Mode on the top right

corner.

6. Click “Confirm the

indicator is blinking

slowly” and chick “Next”.

16

EN

Operation

7. After clicking “Reconnect”, long press the light key

for dialing on the display interface of the cooker hood.

The dialing process will flash for 2 minutes. If the

dialing is successful, “smartlife-xxxx” will appear in

the WiFi setting of the mobile phone.

8. Access your phone's

WLAN Settings, Choose

SmartLife-xxxx and

connect.

9. After connecting to

SmartLife-xxxx, then

return to APP.

10. Connecting to WIFi

hotspot within 1minutes.

11. Displaying this

interface means

connecting successfully.

17

EN

Operation

12. Click “Done” shown as Step 11.

Return to the home interface. If kitchen

hood add in the list of “All Devices”, it

means connection is succeful.

13. Click "Kitchen Hood" enter the

operation interface.

About operation interface:

ON/Off Button

Light Button

When lights are OFF, push once on this button to turn ON the lights.

Push this button again to turn OFF the lights.

Fan Speed Button

You can control the corresponding gears of 1-2-3-P on the cooker hood.

When cooker hood working, could set delay function.

Push this button, the cooker hood will stop working in 5 minutes.

18

Purify ON/Off

Quick Delay Off

La pagina sta caricando ...

CIARRA CBCB6736G-OW Manuale utente

CIARRA CBCB6736G-OW Manuale utente

in altre lingue

Documenti correlati

Altri documenti