Caraudio Systems V4-NBT Guida d'installazione

Caraudio Systems
Marca
Caraudio Systems
Modello
V4-NBT
Tipo
Guida d'installazione
Version 02.07.2019 V4-NBT
v.LOGiC Intelligent Solution
Interface
V4-NBT
Compatible for the F-series BMW with navigation
system or radio and 6.5”, 7”, 8.8” or 10.25”
monitor with 4+2pin HSD2 LVDS connector
Version 02.09.2019 V4-NBT
Page
1
"
Product features
• Plug and play media-controller with controls by factory infotainment (iDrive)
• Own on-screen display and setup
• No coding of vehicle/factory-infotainment necessary
• On 8.8” and 10.25” 24:10 ultrawide monitor 3 picture format modes (split-mode with
factory video, 16:9, 16:9 zoom, full screen and full screen zoom)
• On 6.5” and 7” 16:9 monitor 2 picture format modes (full screen and zoom)
• 3 AV-inputs
• Controls of after-market devices (e.g. DVD-player, DVD-changer, ...) by factory
infotainment (iDrive, see STA + Database for supported devices)
• 2 trigger outputs (+12V max. 1A), separately adjustable switching events (CAN, ACC,
rear-view camera, reverse gear, external navigation)
• Video-in-motion
• Rear-view camera input
• Interactive lane lines
• Automatic switching to rear-view camera input on engagement of reverse gear from
all operation modes
• AV3 can be used for front camera, automatic on parking operation, automatic return
at 20km/h
• Manual switching to rear-view camera (only for vehicles with PDC button)
• Manual return from rear-view and front camera (cancellation of automatic switching)
• Picture-in-picture mode combining after-market rear-view and front camera
picture(s) with factory parking sensor graphics
• Compatible with all factory video accessories (e.g. rear-view camera, Top-View,
nightvison, DVD-changer, TV-tuner)
• Rear-seat-entertainment output for AV-sources connected to the interface
• USB update-port for software-updates by consumer
Version 02.09.2019 V4-NBT
Page
2
"
Contents
1. Prior to Installation
1.1. Delivery contents
1.2. Check compatibility of vehicle and accessories
1.3. Setting the dip switches of the interface-box V4C-M637
1.4. LED’s of the interface-box V4C-M637
2. Connection schema
3. Installation
3.1. Connecting interface-box and harnesses
3.2. Connection to the factory monitor
3.3. Quadlock connector
3.4. Connection to the vehicle-AUX-input
3.5. Connecting peripheral devices
3.5.1. AV-source(s)
3.5.2. After-market front camera
3.5.2.1. Connection to the after-market front camera
3.5.2.2. Settings for connecting an after-market front camera
3.5.3. After-market rear-view camera
3.5.3.1. Connection to the after-market rear-view camera
3.5.3.2. Settings for connecting an after-market rear-view camera
3.5.3.3. Settings for OEM rear-view camera
3.5.4. After-market navigation
3.5.4.1. Connection to the after-market navigation by RGB
3.5.4.2. Settings for connecting an after-market navigation by RGB
3.5.5. Rear-seat-entertainment
3.5.6. Configurable trigger outputs
3.6. Interactive lane lines
3.7. Picture settings
Version 02.09.2019 V4-NBT
Page
3
"
4. Operation
4.1. OSD – On-screen display
4.1.1. OSD – Operation
4.1.1.1. iDrive High
4.1.1.2. iDrive Low
4.1.2. iDrive selection
4.1.3. OSD – Additional setting options
4.2. Video-in-motion function
4.3. Selecting the interface as current AV-source
4.4. Assigning device controls
4.5. Controlling the connected AV-sources
4.5.1.1. Controlling by iDrive High
4.5.1.2. Controlling by iDrive Low
5. Specifications
6. Connections (interface-box)
7. Technical support
Appendix A – Device control table
Legal Information
By law, watching moving pictures while driving is prohibited, the driver must not be
distracted. We do not accept any liability for material damage or personal injury resulting,
directly or indirectly, from installation or operation of this product. This product should only
be used while standing or to display fixed menus or rear-view-camera video when the
vehicle is moving, for example the MP3 menu for DVD upgrades.
Changes/updates of the vehicle’s software can cause malfunctions of the interface. We
offer free software-updates for our interfaces for one year after purchase. To receive a free
update, the interface must be sent in at own cost. Labor cost for and other expenses
involved with the software-updates will not be refunded.
Version 02.09.2019 V4-NBT
Page
4
"
1. Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installation. The
place of installation must be free of moisture and away from heat sources.
1.1. Delivery contents
1.1. Check compatibility of vehicle and accessories
Take down the SW-version and HW-version of the interface boxes, and store this
manual for support purposes.
Requirements
Vehicle 1series (F20/F21), 3series (F30/F31/F32/F33), X3 (F25), all other
F-series vehicles from approx 06/2012, Mini Paceman 2014
Navigation F-series with navigation system or radio with 6.5”, 7”, 8.8“ or
10.25“ monitor with 4+2pin HSD2 LVDS connector
Limitations
Factory-USB-port The AUDIO connection is different if the vehicle is with factory
USB-port, please see the note in chapter “Connection to the
vehicle-AUX-input“!
PDC / inter. lane lines ”PDC – picture in picture” and “interactive lane lines” function is
not simultaneously usable
Video-harness
V4C-VIDEO
Audio-harness
V4C-AUDIO
Harness
V4C-BM03
LVDS cable
CAB-HSD2-RR148
Interface-box
V4C-M637
HW_____ SW_____
Version 02.09.2019 V4-NBT
Page
5
"
1.2. Setting the dip switches of the interface-box V4C-M637
Dip 1 on the back of the interface-box V4C-M637 are used to set the monitor type.
The default setting is:
Vehicle/ navigation
Dip 2
Dip 3
6.5“ monitor (ver.1)
OFF
OFF
6.5“ monitor (ver.2)
OFF
ON
7“ monitor (ver.1)
OFF
OFF
7“ monitor (ver.2)
ON
OFF
8.8“ monitor
OFF
OFF
10.25“ monitor (ver.1)
OFF
OFF
10.25“ monitor (ver.2)
ON
OFF
After each change of the dip switch settings you have to execute a power reset of the
interface-box!
1.3. LED‘s of the interface-box V4C-M637
valid input source
CAN$ok
valid signal
Version 02.09.2019 V4-NBT
Page
6
"
2. Connection schema
Version 02.09.2019 V4-NBT
Page
7
"
Inte rface -box
V4C-M637
FRONT
4+2Pin=HSD2=
LVDS=fe male
vehicle harne ss
Back=of factory
monitor
LVDS=cable
CAB-HSD2-RR148
Version 02.09.2019 V4-NBT
Page
8
"
3. Installation
Switch off ignition and disconnect the vehicle’s battery! The interface needs a permanent
12V source. If according to factory rules disconnecting the battery is to be avoided, it is
usually sufficient to put the vehicle is sleep-mode. In case the sleep-mode does not show
success, disconnect the battery with a resistor lead.
If power source is not taken directly from the battery, the connection has to be checked
for being start-up proven and permanent.
Prior to wire and device installation we suggest to connect and test correct function of all
after-market and factory infotainment equipment!
The interface is installed on the backside of the factory monitor and on the backside of the
navigation computer.
3.1. Connecting interface-box and harnesses
Connect female 18pin Micro-Fit connector of harness V4C-BM0x to the male 18pin
Micro-Fit connector (POWER) on the front of the interface-box V4C-M637.
Connect female 14pin Micro-Fit connector of the video-harness V4C-VIDEO to the
male 14pin Micro-Fit connector (VIDEO) on the rear of the interface-box V4C-M637.
Connect female 16pin Micro-Fit connector of the audio-harness V4C-AUDIO to the
male 16pin Micro-Fit connector (AUDIO) on the rear of the interface-box
V4C-M637.
Version 02.09.2019 V4-NBT
Page
9
"
3.2. Connection to the factory monitor
Connect the female 4+2pin HSD2 LVDS connector of the LVDS cable
CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector (LVDS-OUT) on the front
of the interface-box V4C-M637.
Remove the female 4+2pin HSD2 LVDS connector of the vehicle harness of the
factory monitor and connect it to the male 4+2pin HSD2 LVDS connector (LVDS-IN)
on the front of the interface-box V4C-M637.
Connect the second female 4+2pin HSD2 LVDS connector of the LVDS cable
CAB-HSD2-RR148 to the male 4+2pin HSD2 LVDS connector of the factory monitor.
Inte rface -box
V4C-M637
FRONT
4+2Pin=HSD2=
LVDS=fe male
vehicle harne ss
Back=of factory
monitor
LVDS=cable
CAB-HSD2-RR148
1
2
3
Version 02.09.2019 V4-NBT
Page
10
"
3.3. Quadlock connector
Remove the female Quadlock connector of the vehicle harness from the rear of the
navigation computer.
Remove optical leads from the female Quadlock connector of the vehicle harness and
insert them into the female Quadlock connector of harness V4C-BM03 at the same
position.
Connect female Quadlock connector of vehicle harness to the male Quadlock
connector of harness V4C-BM03.
Connect female Quadlock connector of harness V4C-BM03 to the male Quadlock
connector of the navigation computer
Version 02.09.2019 V4-NBT
Page
11
"
3.4. Connection to the vehicle-AUX-input
Connect the audio-RCA of harness V4C-BM03 to the female RCA-connectors AUDIO
OUT of the audio-harness V4C-AUDIO.
Note: If the vehicle is with factory USB-port, the AUDIO-OUT of the audio harness
V4C-AUDIO must be connected to the Audio-AUX jack bush which is next to the
USBport (instead of to the male RCA on V4C-BM03 harness).
If connecting a rear-set-entertainment an optional RCA Y-cable is plugged in
between, see chapter “Rear-seat-entertainment”
3.5. Connecting peripheral devices
It is possible to connect 3 after-market AV-sources, therefrom optional an an after-market
front camera, an after-market rear-view camera, an after-market navigation and rear-seat-
entertainment to the interface.
Before final installation of the peripheral devices, we recommend a test-run to detect
incompatibility of vehicle and interface. Due to changes in the production of the vehicle
manufacturer is always the possibility of incompatibility.
Version 02.09.2019 V4-NBT
Page
12
"
3.5.1. AV-source(s)
The interface has the possibility to connect and remotely control by navigation buttons 3
pre-programmed devices. The device list in the device control table (appendix A) shows the
pre-programmed remote channels and the related IR-remote cables STA-xxx which must be
ordered separately for the control of the device.
Connect video RCA of AV-source 1 to female RCA connector VIDEO-1, the video RCA
of AV-source 2 to female RCA connector VIDEO-2 and video RCA of AV-source 3 to
female RCA connector VIDEO-3 of the video-harness V4C-VIDEO.
Connect audio RCA of AV-source 1 to female RCA connectors AUDIO-1, the audio RCA
of AV-source 2 to female RCA connectors AUDIO-2 and audio RCA of AV-source 3 to
female RCA connectors AUDIO-3 of the audio-harness V4C-AUDIO.
Using the respective STA-xxx IR-control cable, interconnect the blue-black (yellow-
black) female 3pin AMP connector of harness V4C-BM03 and the IR-port of the AV-
source 1 (AV-source 2). If 3 AV-sources are connected, connect the optionally
available IR-control cable STA-Y between the blue-black female 3pin AMP connector
and the IR-ports of the AV-sources 1 and 3.
Version 02.09.2019 V4-NBT
Page
13
"
3.5.2. After-market front camera
3.5.2.1. Connection to the after-market front camera
Connect the video RCA of the after-market front camera to the female RCA connector
VIDEO-3 of the video-harness V4C-VIDEO.
- The green wire of harness V4C-BM03 can be used
for +12V electric power supply (max. 1A) of the
after-market front camera. Configure in the OSD-
menu “OPTION”, menu item “POWER OUT 2” the
designated electric power supply (see chapter
“Configurable switching outputs”).
-
Note: The after-market front camera is always connected to AV3.
Version 02.09.2019 V4-NBT
Page
14
"
3.5.2.2. Settings for connecting an after-market front camera
You have to configure some settings in the OSD-menus INPUT and OPTION if you want to
connect an after-market front camera (Operation of the OSD: see chapter “OSD-Operation”).
OSD-menu
Menu item
Setting
Explication
INPUT
AV3
OFF
The front camera is connected to AV3
FVC
OFF
Keine Frontkamera angeschlossen
ON
Switches to front camera if parking process is
enabled and reverse gear is released
OPTION
PARK LOGIC
PDC
For vehicles with PDC button. Enabled while
parking process and up to 20 km/h or
together with PDC if existing
RGearOnly
Enabled while parking process
RGearSpeep
Enabled while parking process and up to
20 km/h
RGearTime
Enabled while parking process and up to
20 second
RVC GRAPHIC
PIP1
OEM PDC display of the vehicle
Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling
other modes (e.g. radio). After deactivation you can’t enable the parking process again until
the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be
disabled and enabled again, if existing.
Version 02.09.2019 V4-NBT
Page
15
"
3.5.3. After-market rear-view camera
3.5.3.1. Connection to the after-market rear-view camera
Connect the video RCA of the after-market rear-view camera to the female RCA
connector of the video-harness V4C-VIDEO.
- The green wire of harness V4C-BM03 can be used
for +12V electric power supply (max. 1A) of the
after-market rear-view camera. Configure in the
OSD-menu “OPTION”, menu item “POWER OUT 2”
the designated electric power supply (see chapter
“Configurable switching outputs”).
Version 02.09.2019 V4-NBT
Page
16
"
3.5.3.2. Settings for connecting an after-market rear-view camera
You have to configure some settings in the OSD-menus INPUT and OPTION if you want to
connect an after-market rear-view camera (Operation of the OSD: see chapter “OSD-
Operation”).
OSD-menu
Menu item
Setting
Explication
INPUT
RVC
OFF
No rear-view camera connected
ON
Switches to rear-view camera if reverse gear
is engaged and/or PDC-display is displayed
OPTION
PARK LOGIC
PDC
For vehicles with PDC button. Enabled while
parking process and up to 20 km/h or
together with PDC if existing
RGearOnly
Enabled while parking process
RGearSpeep
Enabled while parking process and up to
20 km/h
RGearTime
Enabled while parking process and up to
20 second
RVC GRAPHIC
PIP1
OEM PDC display of the vehicle activated
LINES
Interactive lane lines activated
Note: You can deactivate the enabled parking process by pressing the iDrive or by enabling
other modes (e.g. radio). After deactivation you can’t enable the parking process again until
the vehicle is diving faster than 20km/h, the ignition is switched off and on or the PDC will be
disabled and enabled again, if existing.
3.5.3.3. Settings for OEM rear-view camera
OSD-menu
Menu item
Setting
Explication
INPUT
RVC
OEM
If a factory rear-view camera is existing!
The interface turns off, if PDC or reverse gear
is enabled and it displays factory rear-view
camera and/or PDC-display
OPTION
PARK LOGIC
PDC
For vehicles with PDC button. Enabled while
parking process and up to 20 km/h or
together with PDC if existing
Version 02.09.2019 V4-NBT
Page
17
"
3.5.4. After-market navigation
3.5.4.1. Connection to the after-market navigation by RGB
Connect the male 6pin connector of the video-harness V4C-VIDEO to the after-
market navigation.
- The pink wire of harness V4C-BM03 can be used
for +12V switching voltage (max. 1A) of the after-
market navigation. Configure in the OSD-menu
MISC, menu item POWER OUT 1 to “ACC” (see
chapter “Configurable switching outputs”).
Note: It is possible to connect the after-market navigation to an AV-input alternatively.
Version 02.09.2019 V4-NBT
Page
18
"
3.5.4.2. Settings for connecting an after-market navigation by RGB
You have to configure some settings in the OSD-menu INPUT if you want to connect an after-
market navigation (Operation of the OSD: see chapter “OSD-Operation”).
OSD-menu
Menu item
Setting
Explication
INPUT
RGB
OFF
No after-market navigation connected
800x480
After-market navigation connected by RGB
Version 02.09.2019 V4-NBT
Page
19
"
3.5.5. Rear-seat-entertainment
Connect the video RCA of the rear-seat-entertainment to the female RCA connector
VIDEO-OUT of video-harness V4C-VIDEO.
Connect the audio-RCA of the rear-seat-entertainment to the female RCA connectors
of the optional RCA-Y-cable.
Connect the audio RCA of the optional RCA-Y-cable to the female RCA connectors
AUDIO OUT of the audio-harness V4C-AUDIO.
Connect the audio RCA of harness V4C-BM03 to the female RCA connectors of the
optional RCA-Y-cable.
Note: The last source keeps active on rear-seat-entertainment if you switch the navigation
to OEM mode.
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
La pagina sta caricando ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

Caraudio Systems V4-NBT Guida d'installazione

Caraudio Systems
Marca
Caraudio Systems
Modello
V4-NBT
Tipo
Guida d'installazione
Scarica il pdf
rapporto

in altre lingue

Documenti correlati

Altri documenti