Risco VUpoint RVNVR04 Guida d'installazione

VUpoint

Network Video Recorder

Models: RVNVR040020/ RVNVR04002P/ RVNVR080020/ RVNVR160020

EN

Installation Guide

Language Page

3

21

39

57

VUpoint

Network Video Recorder

Models: RVNVR040020/ RVNVR04002P/ RVNVR080020/ RVNVR160020

EN

Installation Guide

4

Safety Precautions

These instructions are intended to ensure that the user can use the product correctly to

avoid danger or property loss.

WARNINGS:

 Installation or usage of this product that is not in accordance with the intended

use as defined by the supplier and as described in the instructional materials

can result in damage, injury, or death.

 Make sure this product is not accessible by children and those for whom

operation of the system is not intended.

 All installation and operation should conform to your local electrical safety

codes. The power shall conform to the requirement in the SELV (Safety Extra

Low Voltage) and the Limited power source is rated 12V DC in the IEC60950-1.

 If the device is permanently connected to an electrical power supply, then the

connection should include an easily-accessible disconnection device, such as a

circuit breaker. Do not connect the two power supplying sources to the device

at the same time; it may result in device damage!

 Do not ever attempt to repair your device by yourself, as doing so could result

in damage, injury or death – always contact your installer / supplier agent for

service.

CAUTIONS:

 Make sure the power supply voltage is correct before using the NVR.

 Do not drop the NVR or subject it to physical shock.

 To avoid heat accumulation, good ventilation is required for a proper operating

environment.

 Keep the NVR away from water and any liquid.

 While shipping, the NVR should be packed in its original packing.

NOTE: We assume no liability or responsibility for all the fires or electrical shock

caused by improper handling or installation. We are not liable for any problems caused

by unauthorized modification or attempted repair.

5

Introduction

Thank you for purchasing the RVNVR040020/ RVNVR04002P/ RVNVR080020/

RVNVR160020 Network Video Recorder.

This Quick Start Guide will help you become familiar with your NVR in a very

short time.

Components and Accessories

NVR:

Installation Guide

4/16 Channel NVR Rear Panel Components

Figure 1 RVNVR040020/RVNVR160020 NVR Components

4 Channel PoE NVR Rear Panel Components

Figure 2 RVNVR04002P Components

6

8 Channel PoE NVR Rear Panel Components

Figure 3 RVNVR080020 NVR Components

Power Input Port

PoE Ports to

Connect to

Network Camera

Ethernet Port

VGA Port

HDMI Port

USB Port

7

HDD Installation

DANGER

Shut down the device and then unplug the power cable before you open the

case to replace the HDD!

All figures listed below are for reference only!

For first time installation, please check if the HDD was previously installed.

Please use HDD of 7200rpm or higher.

 Loosen the screws on

the bottom of the chassis.

 Align the HDD with

the four holes in the

bottom.

 Turn the device

upside down and then

secure the screws

(supplied) firmly.

 Connect the Data

cable and power cable to

the HDD and the

mainboard respectively.

 Put back the cover

and then attach the

screws to the rear panel.

The installation is

complete.

8

NVRs and the RISCO Cloud Installer Application

The RISCO Cloud Installer Application provides an interface to your NVR. This

enables you to add an NVR or edit an existing one.

IMPORTANT – An NVR must first be physically installed before adding the

NVR to the system.

Adding an NVR

To add an NVR:

1. Log into the RISCO Cloud Installer Web Interface (for instructions, refer to

the RISCO Cloud Quick Installer Guide).

Figure 4 Sites List Page

2. From the Sites List page, select the Site you wish to add an NVR.

3. From the page that opens, click the IP CAMERAS Sub Tab and then the

NVR Side Tab.

Figure 5 NVR Page

9

4. Click the Add New NVR button; the Add New NVR side panel opens.

Figure 6 Add NVR Side Panel

5. Enter a name for the NVR.

6. Enter the MAC address of the NVR.

7. Click the Add button; the NVR will be added to the network.

Figure 7 NVR Added

10

All the cameras that are connected to the NVR’s LAN will be automatically

detected and displayed on the side panel.

8. Select the boxes of the IP Cameras to be added to the NVR.

NOTE: Only

the IP Cameras in the list that are enabled can be added. In rare cases,

when IP Cameras are on the same LAN and are connected to another site, they will

be displayed but not enabled.

Figure 8 Select Camera for NVR

9. Click Next. A Wizard will guide you through the settings of each of the

selected cameras. You can quit the Wizard at any stage.

The Wizard screens contain mostly read-only information. For each camera

you should select only the required recording mode.

11

Figure 9 Add Camera

10. Recording Mode: If “Motion Detected” is selected, the NVR will record only

if motion is detected by the camera. If continuous is selected, the camera

will record continuously.

11. Click Save & Continue. Repeat the procedure for the other cameras until all

cameras you have selected for the NVR are setup. The following screen

provides a summary of the cameras that have been connected successfully

or that failed to be connected to the NVR.

12. For Wi-Fi Cameras, the following screen opens.

Figure 10 Connecting to Wi-Fi

12

13. Select the required network and then enter the password.

Figure 11 Selecting Wi-Fi network

14. Click Connect; the connect to Wi-Fi screen opens.

Figure 12 Connecting to Wi-Fi

15. Press OK.

13

Figure 13 Summary of Cameras Added to NVR

16. The defined NVR is displayed in the NVR page and is now added to the

site.

Figure 14 NVR Page

14

Editing an NVR

You can edit a selected NVR and add or remove cameras from the NVR.

To edit an NVR:

1. From the NVR page, click the NVR Name; the Edit NVR screen opens.

Figure 15 Edit NVR Screen

Field Description

Name Change the name of the NVR, if required

Firmware Click Check to confirm if a new firmware version is available.

Local Access Click Set and then select UI/CGI to enable access to the NVR’s web

interface for a time period of 60 minutes.

NOTE: You can delete the NVR from the site by clicking Delete NVR from the

bottom right of the screen.

RVNVR080020

15

Figure 16 Edit NVR Settings

2. Click Save to save the current settings or click Edit Cameras to edit Site

cameras; the Cameras list that appears provides information on the cameras

that are connected to the NVR and the cameras that are on the NVR

network but were not added to the NVR.

RVNVR080020

16

Figure 17 Edit NVR Cameras

3. If you wish to add a camera to the NVR, select the checkbox of the camera

that you wish to add and click Add Cameras. The Add Camera side panel

opens.

Cameras that

are already

connected to

the NVR

}

Cameras that

can be added

}

17

Figure 18 Add Camera

4. From the screen that opens, select the Camera Type and the Recording

Mode. If “Motion Detected” is selected, the NVR will record only if motion

is detected by the camera. If continuous is selected, the camera will record

continuously.

5. After making your selection, click Save & Continue.

18

The following screen provides a summary of the cameras that have been

newly added to the NVR.

Figure 19 Cameras Added to NVR

6. Click OK.

1 camera added to the NVR

19

Product Specification

Please refer to the following table for product performance specification.

Parameter

System

Main Processor Quad-core embedded processor

OS Embedded LINUX

Audio

and

Video

IP Camera Input 4/16 Channel, 4/8 Channel PoE

Two-Way Talk 1 Channel Input, 1 Channel Output, RCA

Display

Interface 1 HDMI, 1 VGA

Resolution

HDMI: 3840×2160, 1920×1080, 1280×1024,

1280×720

VGA: 1920×1080, 1280×1024, 1280×720

Decoding Capacity 2ch@4K(30fps)/8ch@1080P(30fps)

Multi-screen Display

4CH: 1/4

8CH: 1/4/8/9

16CH: 1/4/8/9/16

Recording

Compression Smart H.265+/H.265/Smart H.264+/H.264

Resolution

8Mp/ 6Mp/ 5MP/ 4MP/ 3MP/ 1080P/ 1.3MP/ 720P

etc.

Record Rate

80Mbps

Bit Rate

16Kbps ~ 20Mbps Per Channel

Record Mode

Continuous, Motion

Record Interval

1 ~ 120 min (default: 60 min), Pre-record:

1 ~ 30 sec, Post-record: 10 ~ 300 sec

Playback

and

Backup

Search Mode Time/Date

Backup Mode Smartphone, Network, USB

Network

Interface 1 RJ-45 Port (10/100Mbps)

Ethernet Port 1 Independent 100Mbps Ethernet Port

PoE IEEE802.3at/af

Smarthphone IPhone, iPad, Android

Interoperability ONVIF 2.4, SDK, CGI

20

Parameter

Storage

Internal HDD 1 SATA III Port, Up to 6 TB capacity

HDD Mode Single

Electrical

Power Supply DC48V/1.5A

Power Consumption:

4/16 Channels

NVR: <7.5W (Without HDD)

PoE: Max 25.5w for single port, 50w in total

Power Consumption:

8 Channels

NVR: <8.3W (Without HDD)

PoE: Max 25.5w for single port, 80w in total

Environmental

Operating Conditions -10°C ~ +55°C (+14°F ~ +131°F), 86 ~ 106kpa

Storage Conditions -20°C ~ +70°C (-4°F ~ +158°F), 0 ~ 90% RH

Construction

4/16 Channel

Dimensions: 4/16 Channels

Smart 1U, 204.6mm×204.6mm×45.6mm

(8.1" x

8.1" x 1.8")

Net Weight: 4/16 Channels 0.45kg (0.99 lb) (without HDD)

Gross Weight:

4/16 Channels

1.5kg(3.31 lb)(without HDD)

Dimensions: 8 Channels

Smart 1U, 270mm×204.7mm×45.7mm

(10.6" x

8.1" x 1.8")

Net Weight: 8 Channels 0.65kg (1.43 lb) (without HDD)

Gross Weight: 8 Channels 1.8kg (3.97 lb)(without HDD)

Certification

CE EN55032, EN55024, EN50130-4, EN60950-1

FCC Part 15 Subpart B

EMC Compliance Statement

Hereby, RISCO Group declares that this equipment is in compliance with the

essential requirements and other relevant provisions of Directive 2014/30/EU.

For the CE Declaration of Conformity please refer to our website:

www.riscogroup.com

La pagina sta caricando ...

Risco VUpoint RVNVR04 Guida d'installazione

Questo manuale è adatto anche per

Risco VUpoint RVNVR04 Guida d'installazione

in altre lingue

Documenti correlati

Altri documenti