Yamaha RX-V730 Manuale utente

Categoria
Ricevitori AV
Tipo
Manuale utente
OWNER’S MANUAL
RX-V730
U
AV Receiver
0100V730(U)-cv1 12/27/01, 2:16 PM1
I CAUTION
SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating instructions
should be read before the product is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
4 Follow Instructions – All operating and use instructions
should be followed.
5 Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
6 Attachments – Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
7 Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
8 Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9 A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into
the product,
c) If the product has been exposed to rain or water,
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
0101V730_Cau_EN(U) 12/27/01, 2:16 PM2
SAFETY INSTRUCTIONSSAFETY INSTRUCTIONS
CAUTION II
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved
by Yamaha may void your authority, granted by the
FCC, to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and,
if not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one
of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 81020)
GROUNDING CONDUCTORS
(NEC SECTION 81021)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers only)
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its
normal operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
20 Replacement Parts – When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
21 Safety Check – Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is in
proper operating condition.
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the
antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/
NFPA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode.
0101V730_Cau_EN(U) 12/27/01, 2:16 PM3
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 30 cm on the top, 20 cm on the
left and right, and 10 cm at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4
Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may
cause electrical shock to the user and/or
damage to this unit.
6 Do not cover this unit with a newspaper,
tablecloth, curtain, etc. in order not to obstruct
heat radiation. If the temperature inside this unit
rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than
specified is dangerous and may cause fire,
damage to this unit, and/or personal injury.
YAMAHA will not be held responsible for any
damage resulting from use of this unit with a
voltage other than specified.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an
electrical storm.
14 Take care of this unit so that no foreign objects
and/or liquid drops inside this unit.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long
periods of time (i.e. vacation), disconnect the AC
power plug from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding
that this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
19 VOLTAGE SELECTOR (China and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
IMPORTANT
Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
III CAUTION
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
0101V730_Cau_EN(U) 12/27/01, 2:16 PM4
1
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
CONTENTS
INTRODUCTION
INTRODUCTION
CONTENTS ............................................................ 1
FEATURES ............................................................. 2
GETTING STARTED ............................................ 3
Checking the package contents ................................. 3
Installing batteries in the remote control ................... 3
CONTROLS AND FUNCTIONS ......................... 4
Front panel ................................................................ 4
Remote control .......................................................... 6
Using the remote control ........................................... 7
Front panel display .................................................... 8
PREPARATION
SPEAKER SETUP ................................................. 9
Speakers .................................................................... 9
Speaker placement .................................................... 9
Connecting the speakers .......................................... 10
CONNECTIONS .................................................. 13
Before connecting components ............................... 13
Connecting video components ................................ 14
Connecting audio components ................................ 16
Connecting the antennas ......................................... 17
Connecting an external amplifier ............................ 18
Connecting an external decoder .............................. 18
Connecting the power supply cords ........................ 19
Turning on the power .............................................. 19
ON-SCREEN DISPLAY (OSD) .......................... 20
OSD modes ............................................................. 20
Selecting the OSD mode ......................................... 20
SPEAKER MODE SETTINGS .......................... 21
ADJUSTING SPEAKER OUTPUT LEVELS .. 22
Before you begin ..................................................... 22
Using the test tone ................................................... 22
BASIC OPERATION
BASIC PLAYBACK ............................................ 24
Input modes and indications .................................... 26
Selecting a sound field program .............................. 27
DIGITAL SOUND FIELD PROCESSING
(DSP) ................................................................. 30
Understanding sound fields ..................................... 30
Hi-Fi DSP programs ................................................ 30
CINEMA-DSP ...................................................... 31
Sound design of CINEMA-DSP ............................. 31
CINEMA-DSP programs ........................................ 33
TUNING ................................................................ 35
Automatic and manual tuning ................................. 35
Presetting stations .................................................... 36
Tuning in to a preset station .................................... 38
Exchanging preset stations ...................................... 38
SLEEP TIMER ..................................................... 39
Setting the sleep timer ............................................. 39
Canceling the sleep timer ........................................ 39
RECORDING ....................................................... 40
ADVANCED OPERATION
SET MENU ........................................................... 41
Adjusting the items on the SET MENU .................. 41
1 SPEAKER SET (speaker mode settings) ............ 42
2 LFE LEVEL ........................................................ 44
3 SP DLY TIME (speaker delay time) ................... 44
4 D. RANGE (dynamic range) ............................... 45
5 L/R BALANCE (balance of the main left and
right speakers) ..................................................... 45
6 HP TONE CTRL (headphone tone control) ........ 45
7 INPUT RENAME ............................................... 45
8 I/O ASSIGN (input/output assignment) .............. 46
9 INPUT MODE (initial input mode) .................... 46
10DISPLAY SET .................................................... 46
11MEM. GUARD (memory guard) ........................ 47
REMOTE CONTROL FEATURES ................... 48
Control area ............................................................. 48
Setting the manufacturer code ................................. 49
Changing the source name in the display window .. 50
Clearing renamed source names, and setup
manufacturer codes ............................................. 51
Controlling other components ................................. 52
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS ....................................................... 53
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM PARAMETER
EDITING .......................................................... 54
What is a sound field? ............................................. 54
Sound field program parameters ............................. 54
Changing parameter settings ................................... 55
DIGITAL SOUND FIELD PARAMETER
DESCRIPTIONS .............................................. 56
TROUBLESHOOTING ...................................... 60
GLOSSARY .......................................................... 64
SPECIFICATIONS .............................................. 66
0102V730_1-8_EN(U) 12/27/01, 2:16 PM1
2
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks
of Dolby Laboratories.
DTS, ES and DTS Digital Surround are trademarks of
Digital Theater Systems, Inc.
FEATURES
Built-in 6-channel power amplifier
Minimum RMS output power
(0.06% THD, 20 Hz 20 kHz, 8)
Main: 75 W + 75 W
Center: 75 W
Rear: 75 W + 75 W
Rear center: 75 W
Multi-mode digital sound field
processing
Dolby Pro Logic/Dolby Pro Logic decoder
Dolby Digital/Dolby Digital EX decoder
DTS/DTS-ES compatible decoder
CINEMA DSP: Combination of YAMAHA DSP
technology and Dolby Pro Logic, Dolby Digital
or DTS
Virtual CINEMA DSP
SILENT CINEMA DSP
Sophisticated AM/FM Tuner
40-Station random access preset tuning
Automatic preset tuning
Preset station shifting capability (Preset
editing)
Other features
96-kHz/24-bit D/A converter
SET MENU for optimizing this unit for your
Audio/Video system
Test tone generator for easier speaker balance
adjustment
6-channel external decoder input
On screen display function helpful in controlling
this unit
S-video signal input/output capability
Component video input/output capability
Optical and coaxial digital audio signal jacks
Sleep timer
Remote control with preset manufacturer codes
About this manual
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part for the reason of the improvement
in operativity ability, and others. In this case, the product has priority.
0102V730_1-8_EN(U) 12/27/01, 2:16 PM2
3
English
INTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
1
2
3
PHONO
POWER SLEEP
CLEAR
CODE SET
STANDBY
TRANSMIT
RE–NAME
6CH INPUT
SYSTEM
V
-
AUX
A B C
D
-
TV/CBL
POWER
REC
DISC SKIP
SET MENU
TV INPUT
A/B/C/D/E
AUDIO
VOL
LEVEL
MENU
STEREO
HALL
ENTER-
TAINMENT
TV
SPORTS
MONO
MOVIE
SELECT
EX/ES
0
+
10
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SUR.
TEST
ON SCREEN
EFFECT
CHP/INDEX
TV VOL
RETURN
DISPLAY
PRESET PRESET
TV MUTE
TV VOL
SELECT
CHCH
ROCK
CONCERT
JAZZ CLUB
TITLE
MUTE
POWER
AMP
AVTV
VCR2/DVRVCR 1 DVD
SELECT
MD/CD-R
TUNER
CD
+
+
+
3421
5
910
11 12
67 8
Installing batteries in the remote
control
Insert the batteries in the correct direction by aligning the
+ and marks on the batteries with the polarity markings
(+ and ) inside the battery compartment.
1 Press the part and slide off the battery
compartment cover.
2 Insert the four supplied batteries (AAA, R03,
UM-4) according to the polarity markings on
the inside of the battery compartment.
3 Slide the cover back on so that it snaps into
place.
Notes on batteries
Change all of the batteries if you notice a decrease in
the operating range of the remote control, that the
indicator does not flash, or the light becoming dim.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean
the battery compartment thoroughly before installing
new batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
AM loop antenna
(Europe, U.K., Australia and
Singapore models)
Indoor FM antenna
(U.S.A., Canada, China,
Korea and General models)
Batteries (4)
(AAA, R03, UM-4)
Remote control
GETTING STARTED
Checking the package contents
Check your package to make sure it contains the following items.
75-ohm/300-ohm antenna
adapter (U.K. model)
Front VIDEO AUX jack cap
0102V730_1-8_EN(U) 12/27/01, 2:16 PM3
4
NATURAL SOUND AV RECEIVER
SPEAKERS
AB
SILENT
PHONES
STANDBY
/
ON
STEREO
EFFECT
PROGRAM
PRESET
/
TUNING
A/B/C/D/E
BASS
+ +
TREBLE
VIDEO AUX
S VIDEO VIDEO AUDIO OPTICALLR
MEMORY
FM/AM
EDIT
PRESET/TUNING
MAN'L/AUTO FM
AUTO/MAN'L MONO
TUNING MODE
VOLUME
INPUT
INPUT M0DE
6CH INPUT
123 456
sa fd
MEMORY
FM/AM
EDIT
PRESET/TUNING
MAN'L/AUTO FM
AUTO/MAN'L MONO
TUNING MODE
iu po
START
EON
RDS MODE/FREQ
MODE
PTY SEEK
START
EON
RDS MODE/FREQ
MODE
PTY SEEK
7
90 ert8qw y
CONTROLS AND FUNCTIONS
Front panel
1 STANDBY/ON
Turns this unit on, or set it to the standby mode. When
you turn this unit on, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Standby mode
In this mode, this unit will consume a small amount of
power in order to receive infrared-signals from the
remote control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit.
4 INPUT MODE
Sets the priority for the types of input signals (AUTO,
DTS, ANALOG) to receive when one component is
connected to two or more input jacks. Priority cannot be
set when 6CH INPUT is selected as the input source.
5 INPUT l / h
Selects the input source you want to listen to or watch.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the OUT (REC) level.
7 6CH INPUT
Selects the audio source connected to the 6CH INPUT
jacks. This audio takes priority over the source selected
with INPUT l / h (or the input selector buttons on the
remote control).
(U.K. and Europe models)
0102V730_1-8_EN(U) 12/27/01, 2:16 PM4
5
English
INTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
8 SILENT (PHONES jack)
Allows you enjoy DSP effect for private listening with
headphones. When you connect headphones, no signals
are output to the speakers or the OUTPUT jacks.
9 SPEAKERS A/B
Turns the set of main speakers connected to the A and/or
B terminals on or off.
0 STEREO/EFFECT
Switches between normal stereo and DSP effect
reproduction. When STEREO is selected, 2-channel
signals are directed to the main left and right speakers
without effect sounds and all Dolby Digital and DTS
signals (except the LFE channel) are mixed down to the
main left and right speakers.
q PROGRAM l / h
Selects the DSP program.
w PRESET/TUNING l / h
Selects preset station numbers 1 to 8 when the colon (:)
appears in the front panel display.
Selects the tuning frequency when the colon (:) does not
appear.
e A/B/C/D/E
Selects preset station groups A to E.
r BASS
Adjusts the low-frequency response for the main left and
right channels.
Turn right to increase or turn left to decrease the low-
frequency response.
t TREBLE
Adjusts the high-frequency response for the main left and
right channels.
Turn right to increase or turn left to decrease the high-
frequency response.
y VIDEO AUX jacks
Inputs for audio and video signals from a portable
external source (game console, etc.). Set the input source
to V-AUX to enjoy source signals from these jacks.
When the VIDEO AUX jacks on the front panel are not
used, you can attach the provided front VIDEO AUX jack
cap as shown in the illustration. When the cap is not
attached, be sure retain it carefully.
u RDS MODE/FREQ (U.K. and Europe models)
When an RDS station is received, press this button to
change the display mode among the PS mode, PTY mode,
RT mode, CT mode (if the station offers those RDS data
service) and/or frequency display mode in turn.
i PTY SEEK MODE (U.K. and Europe models)
Press this button to set the unit in the PTY SEEK mode.
o PTY SEEK START (U.K. and Europe models)
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
p EON (U.K. and Europe models)
Press this button to select the desired program type
(NEWS, INFO, AFFAIRS, SPORT) when you want to
tune in to a radio program of that type automatically.
a PRESET/TUNING (EDIT)
Switches the function of PRESET/TUNING l / h
between selecting a preset station number and tuning (the
colon (:) turns on or off).
This button is also used to exchange the assignment of
two preset stations with each other.
s TUNING MODE (AUTO/MANL MONO)
Switches the tuning mode between automatic and manual.
d MEMORY (MANL/AUTO FM)
Stores the current station in the memory.
f FM/AM
Switches the reception band between FM and AM.
O
PTICA
L
V
ID
EO
A
U
X
S VID
EO
VID
EO
A
U
D
IO
L
R
0102V730_1-8_EN(U) 12/27/01, 2:16 PM5
6
CONTROLS AND FUNCTIONS
PHONO
POWER SLEEP
CLEAR
CODE SET
STANDBY
TRANSMIT
RENAME
6CH INPUT
SYSTEM
V
-
AUX
A B C
D
-
TV/CBL
POWER
REC
DISC SKIP
SET MENU
TV INPUT
A/B/C/D/E
AUDIO
VOL
LEVEL
MENU
STEREO
HALL
ENTER-
TAINMENT
TV
SPORTS
MONO
MOVIE
SELECT
EX/ES
0 +10
MOVIE
THEATER 1
MOVIE
THEATER 2
/DTS
SUR.
TEST
ON SCREEN
EFFECT
CHP/INDEX
TV VOL
RETURN
DISPLAY
PRESET PRESET
TV MUTE
TV VOL
SELECT
CHCH
ROCK
CONCERT
JAZZ CLUB
TITLE
MUTE
POWER
AMP
AVTV
VCR2/DVRVCR 1 DVD
SELECT
MD/CD-R
TUNER
CD
+
+
+
3421
5
910
11 12
67 8
w
e
r
t
y
u
o
p
a
s
d
i
9
0
8
q
2
3
4
1
5
7
6
Remote control
This section describes the remote control controls and
their functions. Make sure that the AMP mode is selected
before starting operation. See REMOTE CONTROL
FEATURES on pages 48 to 52.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 TRANSMIT indicator
Flashes while the remote control is sending signals.
3 STANDBY
Sets this unit in the standby mode.
4 SYSTEM POWER
Turns on the power of this unit.
5 Å/ı/Ç
Sets the remote control to operate other components (not
necessarily connected to this unit) without changing this
units input source.
6 Input selector buttons
Select the input source and set the remote control to
operate the selected source component.
7 Display window
Shows the selected source component that you are
controlling.
8 LEVEL
Selects the effect speaker channel to be adjusted.
9 Multi control section
Used when changing the setting and to implement the
settings.
0 TEST
Outputs the test tone to adjust the speaker levels.
q DSP program
Select DSP programs for the AMP position. Press a
button repeatedly to select a DSP program within that
group.
w RE-NAME
Used when changing the input source name in the display
window.
e CLEAR
Used when clearing functions acquired using the rename
features, and to set manufacturer codes.
r CODE SET
Used when setting up the manufacturer code (see page
49).
t SLEEP
Sets the sleep timer.
y 6CH INPUT
Selects the audio source connected to the 6CH INPUT
jacks.
0102V730_1-8_EN(U) 12/27/01, 2:16 PM6
7
English
INTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
CODE SET
NATURAL SOUND AV RECEIVER
SPEAKERS
AB
SILENT
PHONES
STANDBY
/
ON
STEREO
EFFECT
PROGRAM
PRESET
/
TUNING
A/B/C/D/E
BASS
+ +
TREBLE
VIDEO AUX
S VIDEO VIDEO AUDIO OPTICALLR
MEMORY
FM/AM
EDIT
PRESET/TUNING
MAN'L/AUTO FMAUTO/MAN'L MONO
TUNING MODE
VOLUMEINPUT
INPUT M0DE
6CH INPUT
30° 30°
Approximately 6 m (20 feet)
u SELECT k/n
Sets the remote to control a component other than the one
selected using the input selector buttons.
i AMP
Switches the function of the same controls between AMP
and the component selected using the input selector
buttons.
o VOL +/
Increases or decreases the volume level.
p MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
a SET MENU
Selects the SET MENU mode.
s ON SCREEN
Displays the input or operation status.
d STEREO/EFFECT
Switches between normal stereo and DSP effect
reproduction. When STEREO is selected, 2-channel
signals are directed to the main left and right speakers
without effect sounds and all Dolby Digital and DTS
signals (except the LFE channel) are mixed down to the
main left and right speakers.
Using the remote control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity or temperature such as near a heater,
stove or bath;
dusty places; or
in places subject to extremely low temperatures.
0102V730_1-8_EN(U) 12/27/01, 2:16 PM7
8
CONTROLS AND FUNCTIONS
RL
LCR
RC RR
LFE
VIRTUAL
DSP
PCM
MATRIX
SILENT
DIGITAL
EON
PS PTY
PTY HOLD
dB
mS
RT
CT
MUTE
SLEEP
STEREO
TUNED
MEMORY
AUTO
PRO LOGIC
/
VOLUME
DTS
MOVIE
THTR
ENTERTAINMENT
12
DOLBY DIGITAL PRO
LOGIC
VCR
V-AUX
DVD
TUNER
PHONO
CD
D
-
TV/CBL
MD/CD
-
R
1
VCR2/DVR
1234
5789
0
qwert y
6
1 Processor indicators
Lights up when the t, g, VIRTUAL,
PRO LOGIC
/
or
DSP
are activated.
MATRIX lights up when the Dolby Digital EX decoder or
the DTS-ES compatible decoder is activated.
2 Input source indicator
Shows the current input source with a cursor.
3 MUTE indicator
Flashes while the MUTE function is on.
4 VOLUME level indicator
Indicates the volume level.
5 v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
6 SILENT indicator
Lights up when headphones are connected while the
digital sound field processor is on.
7 Headphones indicator
Lights up when headphones are connected.
8 DSP program indicators
The name of the selected DSP program lights up when the
ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or V/DTS SURROUND DSP program is
selected.
9 Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
0 RDS indicator (U.K. and Europe models)
The name(s) of the RDS data offered by the currently
received RDS station light(s) up.
EON indicator lights up when an RDS station that offers
the EON data service is being received.
PTY HOLD indicator lights up while searching for
stations in the PTY SEEK mode.
q STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
w TUNED indicator
Lights up when this unit is tuned to a station.
e MEMORY indicator
Flashes to show a station can be stored.
r AUTO indicator
Shows that this unit is in the automatic tuning mode.
t SLEEP indicator
Lights up while the sleep timer is on.
y Input channel indicator
Indicates the channel components of input signals being
received.
Front panel display
(U.K. and Europe models)
0102V730_1-8_EN(U) 12/27/01, 2:16 PM8
9
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
Speakers
This unit has been designed to provide the best sound-
field quality with a 6-speaker system, using main left and
right speakers, rear left and right speakers, a center
speaker, and a rear center speaker. If you use different
brands of speakers (with different tonal qualities) in your
system, the tone of a moving human voice and other types
of sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.
The main speakers are used for the main source sound
plus effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for effect and surround sounds. The center speaker is
for the center sounds (dialog, vocals, etc.). The rear center
speaker supplements the rear (left and right) speakers and
provides for more realistic front-to-back transitions.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use the
models of equivalent performance with the main
speakers.
Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
playing back Dolby Digital or DTS signals. The
YAMAHA Active Servo Processing Subwoofer System is
ideal for natural and lively bass reproduction.
PREPARATION
Speaker placement
Refer to the following diagram when you place the
speakers.
Main speakers
Place the main left and right speakers an equal distance
from the ideal listening position. The distance between
each speaker and each side of the video monitor should
also be the same.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible (such as directly over or under the
monitor) and centrally between the main speakers.
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (6 feet) above the
floor.
Rear center speaker
Place the rear center speaker in the center between the
rear left and right speakers at the same height from the
floor as the rear speakers.
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce wall
reflections.
Note
If you do not use any of effect speakers (rear, center and/or rear
center), change the settings of SPEAKER SET items at the
SET MENU to designate the signals to other terminals you
connect speakers to.
CAUTION
Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
Main
speaker (L)
1.8 m (6 feet)
Rear speaker (L)
Rear center
speaker
Rear speaker (R)
Subwoofer
Main speaker (R)Center speaker
0103V730_9-18_EN(U) 12/27/01, 2:16 PM9
10
SPEAKER SETUP
12
Connecting the speakers
Be sure to connect the left channel (L), right channel (R), + (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
Use speakers with the specified impedance shown on the rear panel of this unit.
Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit
and/or the speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridge.
1 Remove approximately 10 mm (3/8) of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
y
(U.S.A., Canada, Australia, China, Korea and General models)
Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
10 mm (3/8)
MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. When using only one speaker system, it can be
connected to either the MAIN A or the MAIN B terminals.
REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
REAR CENTER SPEAKER terminals
A rear center speaker can be connected to these terminals.
Red: positive (+)
Black: negative ()
Banana plug
2
3
1
(U.S.A. model)
(U.S.A. model)
0103V730_9-18_EN(U) 12/27/01, 2:16 PM10
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
DIGITAL
OUTPUT
SPEAKERS
MAIN
MAIN
DIGITAL
INPUT
6CH INPUT
CD
CD
IN
(PLAY)
OUT
(REC)
DVD
D-TV
/CBL
DVD
OUT
VCR 1
VCR 2
/VDR
MD
/CD-R
D-TV
/CBL
OUT
PHONO
IN
DVD
IN
FM
ANT
AM
ANT
GND
75
UNBAL.
OPTICAL
D-TV/CBL
MD/CD-R
MD/CD-R
OPTICAL
COAXIAL
S VIDEO VIDEO
OUTPUT
S VIDEO
MONITOR OUT
MONITOR
OUT
VIDEO
VIDEO
TUNER
YP
B
/C
B
P
R
/C
R
COMPONENT VIDEO
AUDIOAUDIOGND
MAIN
CENTER
SUB
WOOFER
SUB
WOOFER
SURROUND
CENTER
CENTER
AC OUTLETS
REAR
CENTER
REAR CENTER
OUTPUT
L
R
L
R
L
L
R
R
L
L
L
R
R
A
+
+
+
+
+
B
REAR
(SURROUND)
REAR
(SURROUND)
IMPEDANCE SELECTOR
SET BEFORE POWER ON
R
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
8
16
8
8
8
:4
:8
:6
:6
:6
MAIN
A OR B
A+B
CENTER
REAR CENTER
REAR
MAIN A OR B
A+B
CENTER
REAR CENTER
REAR
:
:
:
:
:
1
56
7
3
2
4
Subwoofer
system
Rear center
speaker
Main B speaker
Center
speaker
Right
Rear speaker
SUBWOOFER jack
When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System,
connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or
rear channels are directed to this jack in accordance with your SPEAKER SET selections. The LFE (low-frequency
effect) signals generated when Dolby Digital or DTS is decoded are also directed to this jack in accordance with your
SPEAKER SET selections.
Notes
The cut-off frequency of the SUBWOOFER jack is 90 Hz.
If you do not use a subwoofer, designate the signals to the main left and right speakers by changing the setting of SPEAKER SET
item 1E BASS on the SET MENU to MAIN.
Use the control on the subwoofer to adjust its volume level. It is also possible to adjust the volume level by using this units remote
control (see ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS on page 53).
Right Left
Main A speaker
Right Left
Left
1
2
4
3
7
6
5
The diagram shows the speaker layout in the listening
room.
0103V730_9-18_EN(U) 12/27/01, 2:17 PM11
12
SPEAKER SETUP
SPEAKERS
MAIN
MAIN
YP
B
/C
B
R
/C
R
O
MPONENT VIDEO
CENTER
CENTER
REAR
CENTER
REAR CENTER
OUTPUT
L
R
L
R
L
L
L
R
R
A
+
+
+
+
+
B
REAR
(SURROUND)
REAR
(SURROUND)
R
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
:4
:8
:6
:6
:6
MAIN
A OR B
A+B
CENTER
REAR CENTER
REAR
MAIN A OR B
A+B
CENTER
REAR CENTER
REAR
:
:
:
:
:
8
16
8
8
8
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
:4
:8
:6
:6
:6
MAIN
A OR B
A+B
CENTER
REAR CENTER
REAR
MAIN A OR B
A+B
CENTER
REAR CENTER
REAR
:
:
:
:
:
8
16
8
8
8
IMPEDANCE SELECTOR
SET BEFORE POWER ON
Switch
position
Left
Right
Speaker
Main
Center
Rear
Center
Rear
Main
Center
Rear
Center
Rear
Impedance level
If you use one set of main speakers,
the impedance of each speaker must
be 4 or higher.
If you use two sets of main speakers,
the impedance of each speaker must
be 8 or higher.
The impedance must be 6 or
higher.
The impedance must be 6 or
higher.
The impedance of each speaker must
be 6 or higher.
If you use one set of main speakers,
the impedance of each speaker must
be 8 or higher.
If you use two sets of main speakers,
the impedance of each speaker must
be 16 or higher.
[Canada model only]
The impedance of each speaker must
be 8 or higher.
The impedance must be 8 or
higher.
The impedance must be 8 or
higher.
The impedance of each speaker must
be 8 or higher.
IMPEDANCE
SELECTOR
switch
(U.S.A. model)
IMPEDANCE SELECTOR switch
WARNING
Do not change setting of the IMPEDANCE SELECTOR switch when the power of this unit is on, this may damage
the unit. If this unit fails to turn on when STANDBY/ON (or SYSTEM POWER) is pressed, the IMPEDANCE
SELECTOR switch may not be fully slid to either position. If so, slide the switch all the way to either position when
this unit is in the standby mode.
Select the switch position (left or right) according to the impedance of the speakers in your system. Be sure to move this
switch only when this unit is in the standby mode.
0103V730_9-18_EN(U) 12/27/01, 2:17 PM12
13
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
Before connecting components
CAUTION
Do not connect this unit or other components to the
mains power until all connections between the
components have been completed.
Be sure all connections are made correctly, that is to
say L (left) to L, R (right) to R, + to + and “–” to
“–”. Some components require different connection
methods and have different jack names. Refer to the
operation instructions for each component to be
connected to this unit.
When you connect other YAMAHA audio components
(such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same
number labels as !, #, $ etc. YAMAHA applies this
labeling system to all its products.
After you have completed all connections, check them
again to make sure they are correct.
The name of jack corresponds to input selector.
Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. To enjoy multi-channel sound track
of DVD software, etc. with DSP effect, you need to make
digital connection. All digital input jacks are acceptable
for 96-kHz sampling digital signals.
Note
The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
DIGITAL
OUTPUT
SPEAKERS
MAIN
MAIN
DIGITAL
INPUT
6CH INPUT
CD
CD
IN
(PLAY)
OUT
(REC)
DVD
D-TV
/CBL
DVD
OUT
VCR 1
VCR 2
/VDR
MD
/CD-R
D-TV
/CBL
DVD
OUT
PHONO
IN
IN
FM
ANT
AM
ANT
GND
75
UNBAL.
OPTICAL
D-TV/CBL
MD/CD-R
MD/CD-R
OPTICAL
COAXIAL
S VIDEO VIDEO
OUTPUT
S VIDEO
MONITOR OUT
MONITOR
OUT
VIDEO
VIDEO
TUNER
YP
B
/C
B
P
R
/C
R
COMPONENT VIDEO
AUDIOAUDIOGND
MAIN
CENTER
SUB
WOOFER
SUB
WOOFER
SURROUND
CENTER
CENTER
REAR
CENTER
REAR CENTER
OUTPUT
L
R
L
R
L
L
R
R
L
L
L
R
R
A
+
+
+
+
+
B
REAR
(SURROUND)
REAR
(SURROUND)
R
AC OUTLETS
(page 19)
6CH INPUT jacks
(page 18)
DIGITAL OUTPUT jack
(page 16)
OUTPUT jacks
(page 18)
DIGITAL INPUT jacks
(pages 13-16)
Antenna input terminals
(page 17)
Speaker terminals
(pages 10-11)
Video component jacks
(pages 14-15)
Audio component jacks
(page 16)
SUBWOOFER OUTPUT
jack (page 11)
0103V730_9-18_EN(U) 12/27/01, 2:17 PM13
14
CONNECTIONS
Connecting video components
Refer to the connection examples on the next page.
Types of video jacks
There are three types of video jacks as follows:
1 VIDEO jack
Conventional composite video signal.
2 S VIDEO jack
Transmits color and luminance separately and achives
high-quality color reproduction.
3 COMPONENT VIDEO jacks
Transmit color difference (P
B
/C
B
, P
R
/C
R
) and
luminance separately and provide the best quality
picture.
Each type of video jack works independently. Signals
input through the composite video, S-video and
component jacks are only output through the
corresponding composite video, S-video, and
component jacks.
Use a commercially available cable specified for
connecting each type of jacks.
The description of the component video jacks may
differ depending on the component (e.g. Y, C
B
, C
R
/Y,
P
B
, P
R
/Y, B-Y, R-Y etc.). When using these jacks, refer
also to the operation instructions for the component
being connected.
Connecting a video monitor
Connect the video input jack on your video monitor to the
MONITOR OUT VIDEO jack.
Note
If you connect this unit with a source component using S-video
(or Component video) jacks, you also need to connect your
video monitor using S-video (or Component video) jacks.
Connecting a DVD player/digital
TV/cable TV
Connect the optical digital audio signal output jack on
your component to the DIGITAL INPUT jack and
connect the video signal output jack on the component to
the VIDEO jack on this unit.
Then connect AUDIO jacks on your component to the
AUDIO jacks on this unit.
y
If your video component has an S-video output or component
video output, connect the S-video signal output jack on the
component to the S VIDEO jack or connect the component
video signal output jacks on the component to the
COMPONENT VIDEO jacks.
The AUDIO jacks are available for a video component which
does not have optical digital output jack. However, multi-
channel reproduction cannot be obtained with audio signals
input from AUDIO jacks.
Connecting a game console or
camcorder
Connect the optical digital audio signal output jack on
your video component to the OPTICAL jack on the front
panel and connect video signal output jack on the
component to the VIDEO jack on the front panel.
y
If your video component has an S-video output, connect the S-
video signal output jack on the component to the S VIDEO
jack.
The AUDIO jacks are available for a video component such as
a camcorder which does not have optical digital output jack.
Connecting a VCR or DVR (digital
video recorder)
Connect the audio signal input jacks on your video
component to the AUDIO OUT jacks and connect the
video signal input jack on the video component to the
VIDEO OUT jack on this unit for picture recording.
Connect the audio signal output jacks on your component
to the AUDIO IN jacks and connect the video signal
output jack on the component to the VIDEO IN jack on
this unit to play a source from your recording component.
Second VCR or digital video recorder can be connected
using VCR 2/DVR jacks.
y
If your video component has an S-video input, connect the S-
video signal input jack on the component to the S VIDEO OUT
jack.
If your video component has an S-video output, connect the S-
video signal output jack on the component to the S VIDEO IN
jack.
Notes
Once you have connected a recording component to this unit,
keep its power turned on while using this unit. If the power is
off, this unit may distort the sound from other components.
S-video and component video signals pass independently
through this units video circuit. Make sure to connect this unit
to both a source component and a recording component using
the video jacks of the same system.
COMPONENT VIDEO
P
R
/C
R
P
B
/C
B
Y
VIDEOS VIDEO
2 1 3
0103V730_9-18_EN(U) 12/27/01, 2:17 PM14
15
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DIGITAL
OUTPUT
DIGITAL
INPUT
6CH INPUT
CD
CD
IN
(PLAY)
OUT
(REC)
DVD
D-TV
/CBL
DVD
DVD
OUT
VCR 1
VCR 2
/VDR
MD
/CD-R
D-TV
/CBL
OUT
PHONO
IN
IN
FM
ANT
AM
ANT
GND
75
UNBAL.
OPTICAL
D-TV/CBL
MD/CD-R
MD/CD-R
OPTICAL
COAXIAL
S VIDEO VIDEO
OUTPUT
S VIDEO
MONITOR OUT
MONITOR
OUT
VIDEO
VIDEO
TUNER
YP
B/CBPR/CR
COMPONENT VIDEO
AUDIOAUDIOGND
MAIN
CENTER
SUB
WOOFER
SUB
WOOFER
SURROUND
L
L
R
R
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
MIN. /SPEAKER
:4
:8
:6
:6
:6
MAIN
A OR B
A+B
CENTER
REAR CENTER
REAR
A/B/C/D/E
BASS
+ +
TREBLE
VIDEO AUX
S VIDEO VIDEO AUDIO OPTICALLR
MEMORY
FM/AM
EDIT
PRESET/TUNING
MAN'L/AUTO FM
AUTO/MAN'L MONO
TUNING MODE
VOLUME
INPUT
INPUT M0DE
6CH INPUT
V V
AUDIO
OUTPUT
AUDIO
INPUT
L
R
VIDEO
OUTPUT
VIDEO
INPUT
L
R
VIDEO
INPUT
V
VIDEO
OUTPUT
V
O
OPTICAL
OUTPUT
AUDIO
OUTPUT
L
R
V
VIDEO
OUTPUT
O
OPTICAL
OUTPUT
V
O
OPTICAL
OUTPUT
VIDEO
OUTPUT
L
R
V
O
indicates video cables
indicates optical cables
indicates right analog cables
indicates left analog cables
indicates signal direction
Video monitor
VCR 1
DVD player
TV/digital TV/
cable TV
Game console or
camcorder
0103V730_9-18_EN(U) 12/27/01, 2:17 PM15
16
CONNECTIONS
Connecting audio components
Connecting a CD player
Connect the coaxial digital output jack on your CD player
to the DIGITAL INPUT CD jack.
y
The AUDIO jacks are available for a CD player which does not
have coaxial digital output jack.
Connecting a CD recorder or MD
recorder
Connect the optical digital signal input jack on your CD
recorder or MD recorder to the DIGITAL OUTPUT MD/
CD-R jack for digital recording.
Connect the optical digital output jack on your CD
recorder or MD recorder to the DIGITAL INPUT MD/
CD-R jack to play a source from your recording
component.
y
The AUDIO jacks are available for an CD recorder or MD
recorder which does not have optical digital input or output
jack.
DIGITAL
OUTPUT
DIGITAL
INPUT
6CH INPUT
CD
CD
IN
(PLAY)
OUT
(REC)
DVD
DVD
OUT
VCR 1
VCR 2
/VDR
MD
/CD-R
D-TV
/CBL
OUT
PHONO
IN
IN
FM
ANT
AM
ANT
GND
75
UNBAL.
OPTICAL
D-TV/CBL
MD/CD-R
MD/CD-R
OPTICAL
COAXIAL
S VIDEO VIDEO
OUTPUT
S VIDEO
MONITOR OUT
VIDEO
VIDEO
TUNER
AUDIOGND
MAIN
CENTER
SUB
WOOFER
SUB
WOOFER
SURROUND
L
L
R
R
AUDIO
L
R
C
O
O
O
OPTICAL
INPUT
OPTICAL
OUTPUT
GND
L
R
OUTPUT
COAXIAL
OUTPUT
C
indicates right analog cables
indicates left analog cables
indicates signal direction
Turntable
CD player
CD recorder or
MD recorder
Notes
Once you have connected a recording component to this unit,
keep its power turned on while using this unit. If the power is
off, this unit may distort the sound from other components.
DIGITAL OUTPUT jack and analog OUT (REC) jacks are
independent. Only digital signals are output from DIGITAL
OUTPUT jack and analog signals from OUT (REC) jacks.
Connecting a turntable
Connect the output jacks on your turntable to the PHONO
jacks.
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an in-line boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
Connect your turntable to the GND terminal to reduce noise in
the signal. Please note that this connection may increase noise
with some record players.
indicates optical cables
indicates coaxial cables
0103V730_9-18_EN(U) 12/27/01, 2:17 PM16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71

Yamaha RX-V730 Manuale utente

Categoria
Ricevitori AV
Tipo
Manuale utente