Novamatic TW7757 Manuale utente

Marca: Novamatic

Modello: TW7757

Categoria: Asciugatrici

Tipo: Manuale utente

www.

.ch

TW 7757

User manual

Istruzioni per l’uso

Condenser dryer with heat pump

Asciugabiancheria a condensa con pompa di calore

0848 559 111

www.fust.ch

Contents

Important safety information 2

Environment 4

Product description 5

Control panel 5

Before first use 6

Programme chart 7

Daily use 8

Care and cleaning 11

What to do if ... 15

Technical specifications 16

Machine settings 17

Installation 17

Service 19

Subject to change without notice

Important safety information

Important! In the interest of your safety

and to ensure the correct use, before

installing and first using the appliance,

read this user manual carefully,

including its hints and warnings. To

avoid unnecessary mistakes and

accidents, it is important to ensure that

all people using the appliance are

thoroughly familiar with its operation

and safety features. Save these

instructions and make sure that they

remain with the appliance if it is moved

or sold, so that everyone using it through

its life will be properly informed on

appliance use and safety.

- Please read the instruction book be-

fore using this appliance.

General safety

• It is dangerous to alter the specifications or

attempt to modify this product in any way.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use

of the appliance by a person responsible

for their safety.

• Make sure that small children and pets do

not climb into the drum. To avoid this,

please check into the drum before using.

• Any objects such as coins, safety pins,

nails, screws, stones or any other hard,

sharp material can cause extensive dam-

age and must not be placed into the ma-

chine.

• In order to avoid danger of fires caused by

excessive drying, do not use appliance to

dry the following items: Cushions, quilts

and the like (these items accumulate heat).

• Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fit-

ted with foam rubber pads should not be

dried in the tumble dryer.

• Always unplug the appliance after use,

cleaning and maintenance.

• Under no circumstances should you at-

tempt to repair the machine yourself. Re-

pairs carried out by inexperienced persons

may cause injury or serious malfunction-

ing. Contact your local Service Centre. Al-

ways insist on genuine spare parts.

• Items that have been soiled with substan-

ces such as cooking oil acetone, petrol,

kerosene, spot removers, turpentine, wax-

es and wax removers should be washed in

hot water with an extra amount of deter-

gent before being dried in the tumble dry-

er.

• Danger of explosion: Never tumble dry

items that have been in contact with in-

flammable solvents (petrol, methylated

spirits, dry cleaning fluid and the like). As

these substances are volatile, they could

cause an explosion. Only tumble dry items

washed with water.

• Risk of fire: items that have been spotted

or soaked with vegetable or cooking oil

constitute a fire hazard and should not be

placed in the tumble dryer.

• If you have washed your laundry with stain

remover you must execute an extra rinse

cycle before loading your tumble dryer.

• Please make sure that no gas lighters or

matches have accidentally been left in

pockets of garments to be loaded into ap-

pliance

Warning!

• Never stop a tumble dry before the

end of the drying cycle unless all

items are quickly removed and

spread out so that the heat is dis-

sipated. Risk of fire!

•

Lint must not be allowed to accu-

mulate around the tumble dryer.

• Risk of electric shock! Do not spray

down the appliance with jets of water.

• The final part of a tumble dryer cycle oc-

curs without heat ( cool down cycle ) to

ensure that the items are left at a temper-

ature that ensures that items will not be

damaged.

• The tumble dryer is not to be used if in-

dustrial chemicals have been used for

cleaning.

• Ensure you have good ventilation in the in-

stallation room to avoid the back flow of

gases into the room from appliances burn-

ing other fuels, including open fires.

Installation

• This appliance is heavy. Care should be

taken when moving it.

• When unpacking the appliance, check that

it is not damaged. If in doubt, do not use it

and contact the Service Centre.

• All packaging must be removed before

use. Serious damage can occur to the

product and to property if this is not ad-

hered to. See relevant section in the user

manual.

• Any electrical work required to install this

appliance should be carried out by a quali-

fied electrician or competent person.

• If the machine is situated on a carpeted

floor, please adjust the feet in order to al-

low air to circulate freely under the appli-

ance.

• After having installed the appliance, check

that it is not pressing or standing on its

electrical supply cable.

• If the tumble dryer is placed on top of a

washing machine, it is compulsory to use

the stacking kit (optional accessory).

Use

• This appliance is designed for domestic

use. It must not be used for purposes other

than those for which it was designed.

• Only wash fabrics which are designed to

be machine dried. Follow the instructions

on each garment label.

• Do not dry unwashed items in the tumble

dryer.

• Do not overload the appliance. See the

relevant section in the user manual.

• Clothes which are dripping wet should not

be placed in the dryer.

• Garments which have been in contact with

volatile petroleum products should not be

machine dried. If volatile cleaning fluids are

used, care should be taken to ensure that

the fluid is removed from the garment be-

fore placing in the machine.

• Never pull the power supply cable to re-

move the plug from the socket; always

take hold of the plug itself.

• Never use the tumble dryer if the power

supply cable, the control panel, the work-

ing surface or the base are damaged so

that the inside of the tumble dryer is ac-

cessible.

• Fabric softeners, or similar products

should be used as specified by the fabric

softener instructions.

• Caution - hot surface : Do not touch the

door light cover surface when the light is

switched on.

(Only dryers equipped with internal drum

light)

Child safety

• This machine is not intended for use by

young children or infirm persons without

supervision.

• Children often do not recognise the haz-

ards associated with electrical appliances.

Children should be supervised to ensure

that they do not play with the appliance.

• The packaging components (e.g. plastic

film, polystyrene) can be dangerous to chil-

dren - danger of suffocation! Keep them

out of children’s reach.

• Keep all detergents in a safe place out of

children’s reach.

• Make sure that children or pets do not

climb into the drum.

Environment

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will help

prevent potential negative consequences for

the environment and human health, which

could otherwise be caused by inappropriate

waste handling of this product. For more

detailed information about recycling of this

product, please contact your local council,

your household waste disposal service or the

shop where you purchased the product.

Environmental tips

• In the dryer, laundry becomes fluffy and

soft. Fabric softeners are not therefore

needed when washing.

• Your dryer will function most economically

if you:

– Always keep the ventilation slots on the

base of the dryer unobstructed;

– Use the loading volumes specified in the

programme overview;

– Ensure you have good ventilation in the

installation room;

– Clean the micro-fine filter and fine strain-

er after each drying cycle;

– Spin the laundry well before drying.

Energy consumption depends on spin-

ning speed set in washing machine.

Higher spinning speed - lower energy

consumption.

Environmental information

The packaging materials are environmentally

friendly and can be recycled. The plastic

components are identified by markings, e.g.

>PE<, >PS<, etc. Please dispose of the

packaging materials in the appropriate con-

tainer at the community waste disposal fa-

cilities.

Important! The heat pump of your dryer

contains a closed refrigerant circuit filled with

a refrigerant which is free from fluoro-chloro-

hydrocarbons. The refrigerant circuit in the

heat pump must not be damaged.

Warning! When a unit is no longer being

used:

• Pull the plug out of the socket.

• Cut off the cable and plug and dispose

of them.

• Dispose of the door catch. This pre-

vents children from trapping them-

selves inside and endangering their

lives.

Product description

1 Control panel

2 Water reservoir

3 Drum light

4 Fine fluff filter

5 Course fluff filter

6 Fluff filter

7 Rating plate

8 Loading door (reversible)

9 Heat exchanger door, fluff filter, heat ex-

changer

10 Button for opening door in plinth

11 Ventilation grille

12 Adjustable feet

Control panel

6 5 4

321

1 Programme selector and on/off switch

2 Function buttons

3 START PAUSE button

4 DELAY START button

5 Status LED

6 Display

Display

1356

1 time to end / error message

2 cycle phase status

3 options

4 warnings

5 spin speed selection

6 dryness selection

Display description

dryness default

minimal dryness

medium dryness

maximal dryness

spin speed default

minimal spin speed

spin speed scope (200 rpm

step)

maximal spin speed

iron dry (drying phase indica-

tor)

light dry (drying phase indica-

tor)

cupboard dry (drying phase

indicator)

strong dry (drying phase indi-

cator)

extra dry (drying phase indi-

cator)

cooling (drying phase indica-

tor)

crease guard (drying phase

indicator)

empty water reservoir (warn-

ing)

clean condenser (warning)

clean filters (warning)

child lock

long anti-crease

buzzer

time

delay start

cycle duration

time program scope (10 min

- 3h)

delay start scope

Before first use

Warning! If the appliance was not

transported in an upright position, leave

it to stand for 12 hours before

connecting it to the electricity supply and

using it for the first time, so that the oil

can flow back to the compressor.

Otherwise the compressor could be

damaged.

In order to remove any residues which may

have been produced during production, wipe

the dryer drum with a damp cloth or carry out

a brief drying cycle (ca. 30 min.) with damp

cloths in the machine.

Programme chart

Pro-

grammes

max.

load

Application/properties Options

Care

mark

Cottons (Baumwolle)

Extra dry (Ex-

tratrocken)

7 kg

Thorough drying of thick or multi- layered fab-

rics, e.g. terry towelling items, bathrobes.

all except

Time (Zeit-

wahl)

Intensive dry

(Starktrocken)

7 kg

Thorough drying of thick fabrics, e.g. terry tow-

elling items, towels, cottons.

all except

Time (Zeit-

wahl)

Cupboard dry

(Schrank-

trocken)

7 kg

Thorough drying of fabrics of even thicknesses,

e.g. terry towelling items, knitwear, towels.

all except

Time (Zeit-

wahl)

Iron dry (Bü-

geltrocken)

7 kg

For normal thickness cotton or linen laundry,

e.g. bedding, table linen.

all except

Time (Zeit-

wahl)

Easy care (Mischgewebe)

Extra dry (Ex-

tratrocken)

3 kg

Thorough drying of thick or multi-layered fabrics,

e.g. pullovers, bedding, table linen.

all except

Time (Zeit-

wahl)

Cupboard dry

(Schrank-

trocken)

3 kg

For thin fabrics which are not ironed, e.g. easy

care shirts, table linen, baby clothes, socks, lin-

gerie with bones or wires.

all except

Time (Zeit-

wahl)

IRON DRY

(Bügeltrock-

en)

3 kg

For thin fabrics which are also to be ironed, e.g.

knitwear, shirts.

all except

Time (Zeit-

wahl)

special

Time pro-

gramme (Zeit-

programm)

7 kg For drying of individual items of laundry.

all except Dry-

ness (Trock-

engrad) and

Spin speed

(U/Min.)

Freshen-up

(Auffrishen)

1 kg

For refreshing or gently cleaning textiles with

commercially available dry cleaning products.

Long anti-

crease (Knit-

terschutz +),

Buzzer (Sig-

nal), Delay

start (Zeitvor-

wahl)

Micro-fibre

(Mikrofaser)

1 kg

For thin fabrics, polyester and polyamide, which

are not ironed.

all except

Time (Zeit-

wahl)

Mixed (Mix-

Programm)

3 kg

For drying cotton and synthetic fabrics, uses low

temperature.

all except

Time (Zeit-

wahl)

Bed linen

(Bettwäsche)

3 kg

Bed linen (single and double sheet, pillowcase,

bedspread, duvet cover).

all except

Time (Zeit-

wahl)

Pro-

grammes

max.

load

Application/properties Options

Care

mark

Viscose (Vis-

kose)

1 kg

For thin fabrics, viscose, and polyester, which

are not ironed.

all except

Time (Zeit-

wahl)

Jeans 7 kg

For leisure clothing, such as jeans, sweat-shirts,

etc., of different material thicknesses (e.g. at the

neck, cuffs and seams).

all except

Time (Zeit-

wahl)

Sports light

(Sport)

2 kg

For sportswear, thin fabrics, polyester, which

are not ironed.

all except

Time (Zeit-

wahl)

Shirts (Hem-

den)

1.5 kg

(or 7

shirts)

Special program with anti-crease mechanism

for easy care fabrics such shirts and blouses; for

minimum ironing effort. The results depends on

the type of fabric and its finish. Place fabrics in

the dryer straight after spinning; once dried, im-

mediately remove fabrics and place on a clothes

hanger.

all except

Time (Zeit-

wahl)

Easy iron plus

(Leichtbügeln

Plus)

1 kg (or

shirts)

Special program with anti-crease mechanism

for easy care fabrics such shirts and blouses; for

minimum ironing effort. The results depend on

the type of fabric and its finish. Place fabrics in

the dryer straight after spinning; once dried, im-

mediately remove fabrics and place on a clothes

hanger.

all except

Time (Zeit-

wahl)

Silk (Seide) 1 kg

For drying silk using warm air and gentle move-

ment.

all except

Time (Zeit-

wahl)

Wool (Wolle) 1 kg

For drying woollen fabrics after they have been

washed, using warm air at minimum mechanical

load. Follow section Sorting laundry . Recom-

mendation: Remove fabrics immediately after

drying, as no anti-crease programme follows.

all except

Long anti-

crease (Knit-

terschutz +)

and Time

(Zeitwahl)

1) maximal weight of dry clothes

Daily use

Sorting laundry

• Sort by fabric type:

– Cotton/linen for programmes in Cottons

(Baumwolle) programme group.

– Mixtures and synthetics for pro-

grammes in Synthetics (Mischgewebe)

programme group.

• Sort by care label: The care labels mean:

Drying in the tumble dryer possible in

principle

Drying at normal temperature

Drying at reduced temperature

Drying in the tumble dryer not possible

Important! Do not place in the appliance any

wet laundry which is not specified on the care

label as being suitable for tumble-drying.

This appliance can be used for all wet laundry

items which are labelled as suitable for tum-

ble-drying.

• Do not dry new, coloured textiles together

with light-coloured laundry items. Textile

colours may bleed.

• Do not dry cotton jersey and knitwear with

the Extra programme. Items may shrink!

• Wool and wool-like textiles can be dried

using the Wool (Wolle) programme. Before

the drying cycle spin the woollen textiles as

well as possible (max. 1200 rpm). Only dry

woollen textiles together of similar or the

same material, colour and weight. Please

dry heavy laundry items made of wool sep-

arately.

Preparing laundry

• To avoid laundry becoming tangled: close

zips, button up duvet covers and tie loose

ties or ribbons (e.g. of aprons).

• Empty pockets. Remove metal items (pa-

per clips, safety pins, etc).

• Turn items with double-layered fabrics in-

side out (e.g. with cotton-lined anoraks,

the cotton layer should be outermost).

These fabrics will then dry better.

Important! Do not overload the appliance.

Observe max. loading volume of 7 kg.

Average laundry weights

bathrobe 1200 g

quilt cover 700 g

man’s work shirt 600 g

man’s pyjamas 500 g

sheet 500 g

tablecloth 250 g

man’s shirt 200 g

night dress 200 g

pillow case 200 g

towelling towel 200 g

blouse 100 g

ladies’ briefs 100 g

men’s underpants 100 g

napkin 100 g

tea cloth 100 g

Switching machine/drum light on

Turn the programme selector to any pro-

gramme or turn it to Drum light (Beleuch-

tung). The machine has been switched on.

When the loading door is opened, the drum

light is illuminated.

Laundry loading

Open loading door:

Use force to push against the loading

door (push point)

2. Load your laundry (do not force it in).

Caution! Do not jam laundry in between

the loading door and rubber seal.

3. Close loading door securely. Lock must

audibly lock.

Selecting the programme

Use the programme selector to set the pro-

gramme you require. The estimated time to

end of the programme appears on the LCD,

e.g.

( hours . minutes ).

During the cycle, time elapses by steps of

one minute.

Dryness (Trockengrad)

Increases the dryness of the dried laundry

adequately to the selected level:

, . This option helps to achieve

satisfying result of drying.

Spin speed (U/Min.)

Shorten the drying cycle adequately to the

spin speed the laundry was spun previously

in the washing machine. The higher spin

speed was, the shorter drying cycle length.

Available spin speed values (rpm): from

up to (with 200 rpm steps)

This option allows to save time and energy.

Long anti-crease (Knitterschutz +)

Prolongs standard anti-crease phase at the

end of the drying cycle to 90 min. When ac-

tive the symbol

is on. This option helps to

keep laundry free from creases. Laundry can

be removed at any time during the anti-

crease phase.

Buzzer (Signal)

Audible confirmation of:

–cycle end

– anti-crease phase start and end

– cycle interruption

– error

When active the symbol

is on.

Time (Zeitwahl)

Operates only with Time programme (Zeit-

programm). Allows to set individual time of

drying from minimum 10 min. to maximum of

3 hours (in 10 min. steps).

1. Turn the programme knob to the Time

programme (Zeitprogramm).

2. Press the Time (Zeitwahl) button repeat-

edly until the desired programme dura-

tion is shown in the display, e.g.

for

a programme of 1 hour and 20 minutes.

Delay start (Zeitvorwahl)

Allows to delay the start of a drying pro-

gramme from minimum of 30 min. to

maximum of 20 hours.

1. Select the drying programme and addi-

tional options.

2. Press the Delay start (Zeitvorwahl) button

repeatedly until the desired delay start is

shown in the display, e.g.

if the pro-

gramme has to start after 12 hours.

3. To activate the delay timer, press the

Start Pause button. Time to start elapses

in the displayed.

Setting child lock

The child lock can be set to prevent a pro-

gramme being accidentally started or a pro-

gramme in operation being accidentally

changed. The child lock function locks all

buttons and the programme knob. The child

lock can be activated or deactivated by hold-

ing down the Long anti-crease (Knitterschutz

+) and Buzzer (Signal) buttons simultaneous-

ly for 5 seconds.

– Before programme is started: Appli-

ance cannot be used

– After programme is started: Pro-

gramme in operation cannot be

changed

The padlock symbol

appears in the dis-

play to indicate that the child safety device is

activated.

The child safety device is not deactivated

once the programme comes to an end.

If you want to set a new programme, you

must first deactivate the child safety device.

Starting the programme

Press the Start Pause button. The pro-

gramme is started.

The programme progress is shown in LCD

by appropriate set of icons. From left to the

right, from iron dry

to anti-crease icon

depends on the drying cycle chosen. E. g. in

case of cupboard dry programme the follow-

ing status icons are visible:

Current cycle progress is marked by flashing

dash under status icon. When appropriate

part of drying cycle is accomplished dash

becomes steady and appears flashing under

next status icon.

Changing programme

To change a programme which has been se-

lected by mistake once the programme has

started, first turn the programme selector to

Off (Aus) and then reset the programme.

The programme can no longer be

changed directly once the programme

has started. If nevertheless there is an

attempt to change the programme on

the programme knob, the programme

progress display and the maintenance

indicators flash. If an option (excluding

the buzzer ) is set, Err appears in the

multidisplay. The drying programme is

not however affected by this (laundry

protection).

Programme complete / Laundry

unloading

Once the drying cycle is complete, display

shows a blinking

, under anti-crease

icon appears dash. If the buzzer option has

been set, an acoustic signal sounds intermit-

tently for about one minute.

The drying cycles (except for the Wool

(Wolle) programme) are automatically

followed by an anti-crease phase which

lasts around 30 minutes. The drum ro-

tates at intervals during this phase. This

keeps the laundry loose and free of crea-

ses. The laundry can be removed at any

time during the anti-crease phase. (The

laundry should be taken out towards the

end of the anti-crease phase at the latest

to prevent creases from forming.) If long

anti-crease

option has been set, the

anti-crease phase is lengthened by 60

minutes.

1. Open door.

2. Before removing the laundry, remove fluff

from the micro-fine filter. It is best to use

a damp hand for this purpose. (See “Care

and cleaning” chapter.)

3. Remove laundry.

4. Turn the programme selector to Off (Aus).

Important! After each drying cycle:

- Clean the micro-fine filter and fine filter

- Drain the condensed water container

(See chapter “Care and cleaning”.)

5. Close the door.

Care and cleaning

Cleaning fluff filters

The filters collect all the fluff which accumu-

lates during drying. To ensure that the dryer

works perfectly, the fluff filters (micro-fine fil-

ter and fine strainer) must be cleaned after

every drying cycle.

The warning lamp

lights to remind you of

this operation at the end of each cycle.

Caution! Never operate the dryer

without fluff filters or with damaged or

blocked fluff filters.

1. Open loading door

2. Use a damp hand to clean the micro- fine

filter, which is built into the lower part of

the loading aperture.

3. After a period of time, a patina due to

detergent residue on laundry forms on

the filters. When this occurs, clean the

filters with warm water using a brush.

Remove the filter from the door pulling it

out. (It can be positioned with the locat-

ing spur facing to the left or to the right).

After cleaning do not forget to put it

back.

4. Push down the unlock button on the

large mesh filter.

The large mesh filter pops up.

5. Take out fine filter.

6. Remove the fluff from fine filter. It is best

to use a damp hand for this purpose.

Clean the entire filter area

The filter area does not have to be

cleaned after every drying cycle, but

should be checked regularly and

cleaned of fluff if necessary.

7. To do this, grip the top of the large mesh

filter and pull it forwards until it comes

loose from the two brackets.

8. Remove fluff from the entire filter area. It

is best to use a vacuum cleaner for this

purpose.

9. Press both journals of the large mesh fil-

ter into the brackets on the loading door

until they snap into place.

10. Re-insert fine filter.

11. Press against the large mesh filter until it

locks into the interlock.

If the fine filter is not fitted, the large mesh

filter will not snap into place and the

loading door cannot be closed.

Clean the door seal

Wipe the door seal with a damp cloth imme-

diately after the drying cycle has finished.

Emptying the water reservoir

Empty the water reservoir after every drying

cycle.

If the water reservoir is full, an active pro-

gramme will break off automatically and the

warning lamp

lights. In order to continue

the programme, the water reservoir must first

be emptied.

Warning! The condensed water is not

suitable for drinking or for preparing

foodstuffs.

1. Take out drawer containing water reser-

voir completely 1 and pull up the water

reservoir's drainage pipe as far as it will

go 2 .

2. Pour the condensed water out into a ba-

sin or similar receptacle.

3. Slide the outlet connections in and refit

the water reservoir.

If the programme has been interrupted as

a result of the water reservoir being full:

Press the Start/Pause button to continue

the drying cycle.

The water reservoir has a volume of ap-

prox. 4 litres. This is sufficient for around

7 kg of laundry which has previously

been spun at 1000 revolutions / minute.

The condensed water can be used as

distilled water, e.g. for steam ironing.

However it must first be filtered (e.g. with

a coffee filter) to remove any residue and

small pieces of fluff.

Cleaning heat exchanger filter

If the warning lamp

heat exchanger lights,

the heat exchanger fluff filters in the base of

the appliance must be cleaned, i.e. after each

5 drying cycles. Both filters are located in the

appliance base.

Water can collect in the filter housing

therefore it is normal for the heat ex-

changer fluff filters to become wet.

Important!

• Never operate the dryer without the fluff fil-

ters.

• Clogged filters cause higher energy con-

sumption (drying cycle elongation) and

dryer damage.

• A dirty heat pump can only be cleaned up

by means of a costly process.

1. Open door in plinth: To do this, press the

release button on the right and open the

door in the plinth to the left.

2. Pull the filter housing out of the base by

the handle.

3. To clean the fluff filter: Remove filter from

filter housing. To do this, press the pres-

sure points on the sides and pull the filter

frame up and out of the housing. Remove

fluff from the fluff filter with a damp hand.

4. Use a damp hand to remove the fluff from

the filter in the base . If necessary pull out

and clean the filter with warm water using

a wiper or brush. Clean the inside of the

door, the fluff filter chamber and the rub-

ber seals of fluff.

5. Insert the fluff filter to the base a . Insert

the second fluff filter into the filter housing

(it has to audibly lock) and slide it inside

the filter chamber b . Close the door in

plinth. Note: If the fluff filter is not inserted

in the filter housing, the filter housing can-

not be slide into the appliance base.

6. As necessary, approx. once every 6

months, remove the fluff from the heat

exchanger using the sponge supplied.

When doing this, please use rubber

gloves.

Tip: The fluff can be removed more easily if

it is first dampened (e. g. with a laundry

dampener) or with help of vacuum cleaner.

What to do if ...

Troubleshooting by yourself

Problem

Possible cause Remedy

Dryer does

not work.

Dryer not connected to mains supply.

Plug in at mains socket. Check fuse in

fuse box (domestic installation).

Loading door opened. Close loading door

The START PAUSE button not pressed. Press the START PAUSE button.

Unsatisfactory

drying results.

Incorrect programme set.

Set suitable programme.

Fluff filters clogged.

Clean fluff filters.

Heat exchanger clogged.

Clean heat exchanger.

Max. loading exceeded. Respect max. loading volume.

Covered ventilation grill. Uncover ventilation grill in base area.

Residue inside the drum. Clean the drum inside.

High water hardness.

Set suitable water hardness

Loading door

does not close

Filters not locked in place.

Install fine filter and/or snap course filter

into place.

Err ( Error ) on

the LCD.

Attempt to change parameters after start

of the programme.

Turn the dryer off and on. Set requested

parameters.

No drum light

Programme selector in OFF position.

Turn it to DRUM LIGHT (if available) or to

any programme.

Defective light bulb. Replace light bulb (see next section).

Abnormally

elapsing time

on the LCD

Time to end is calculated on the basis of:

type, volume and dampness of laundry.

Automatic process; this is not a machine

fault.

Programme

inactive

Full water reservoir.

Empty water reservoir

, press START

PAUSE button.

Drying cycle

to short

Small laundry volume./Too dry laundry for

selected programme.

Select time programme or higher drying

level (e.g. EXTRA DRY).

Drying cycle

to long

Fluff filters clogged. Clean fluff filters.

To high loading volume. Respect max. loading volume.

Laundry insufficiently spun. Spun adequately the laundry.

Particularly high room temperature - no

machine fault.

Lower the room temperature if possible.

1) In case of error message on the LCD (e.g. E51 - only dryers with the LCD): Switch the dryer off and

on. Set programme. Press the START PAUSE button. Does not work? - inform local service and quote

the error code.

2) follow program recommendation - see Programme overview chapter

3) see Care and cleaning chapter

4) see Machine settings chapter

5) only dryers with the LCD

6) Note: After around 5 hours the drying cycle ends automatically (see Drying cycle complete section).

Changing the bulb for interior lighting

Only use a special bulb which is designed

specially for dryers. The special bulb can be

obtained from your local service centre.

Important! When the appliance is switched

on, the interior lighting switches itself off after

4 minutes when the door is open.

Warning! Do not use standard bulbs!

These develop too much heat and may

damage the machine!

Before replacing the bulb, disconnect

the mains plug; with a permanent con-

nection: fully unscrew or deactivate the

fuse.

1. Unscrew cover above the bulb (this can

be found directly behind the loading aper-

ture, at the top; refer to “Description of

machine” section.)

2. Replace defective bulb.

3. Screw cover back down.

Check the correct positioning of o-ring gas-

ket before screwing back the door light cov-

er. Do not operate the dryer when missing o-

ring gasket on door light cover.

Warning! For safety reasons, the cover

must be screwed down tightly. If this is

not done, the dryer must not be

operated.

Technical specifications

Parameter Value

Height x width x depth 85 x 60 x 58 cm

Drum volume 108 l

Depth with loading door open 109 cm

Height can be adjusted by 1.5 cm

Weight when empty approx. 60 kg

Loading volume (depends on programme)

max. 7 kg

Voltage 220-230 V

Required fuse 6 A

Total power 1350 W

Energy efficiency class

Energy consumption (7 kg of cotton, pre-spun at

1000 rpm)

2.4 kWh

Average annual energy consumption 160.9 kWh

Use Domestic

Permissible ambient temperature + 5°C to + 35°C

Consumption values

The consumption values have been established under standard conditions. They may deviate when

the machine is operated in domestic circumstances.

Programme

Energy consumption in kWh / average drying

time in min.

COTTON CUPBOARD DRY

2.4/ 130 (7 kg load pre-spun at 1000 rpm)

2.3 (7 kg load pre-spun at 1200 rpm)

2.2 (7 kg load pre-spun at 1400 rpm)

2.0 (7 kg load pre-spun at 1800 rpm)

COTTON IRON DRY

1.8/ 105 (7 kg load pre-spun at 1000 rpm)

Parameter Value

SYNTHETICS CUPBOARD DRY

0.75/ 50 (3 kg load pre-spun at 1200 rpm)

1) Different loading volume data may be needed in some countries as a result of different measuring

methods.

2) in accordance with EN 61121

3) Hints for test institutes: cycle has to be checked in accordance with EN 61121

Machine settings

Setting Implementation

Buzzer permanent

on/off

1. Turn the programme selector to any programme.

2. Press simultaneously the Dryness (Trockengrad) and Spin speed (U/Min)

buttons and hold down for approx. 5 seconds.

3. The buzzer is by default always off. You can use the buzzer option to

activate or deactivate sound but the machine does not memorize your

selection.

Water hardness

1. Turn the programme selector to any programme.

2. Press simultaneously the Dryness (Trockengrad) and Time (Zeitwahl) but-

tons and hold down for approx. 5 seconds. The current setting is on the

display:

–

low conductivity <300 μS/cm

–

medium conductivity 300-600 μS/cm

–

high conductivity >600 μS/cm

3. Press the Start pause button sequentially until you set desired level.

4. To memorize setting press simultaneously the Dryness (Trockengrad) and

Time (Zeitwahl) buttons or turn knob to Off (Aus) position

Emptying water res-

ervoir

- warning

off

1. Turn the programme selector to any programme.

2. Press simultaneously the Spin speed (U/Min) and Time (Zeitwahl) buttons

and hold down for approx. 5 seconds.

The current setting is on the display:

–

warning

icon and - warning message is off

–

warning

icon and - warning message is switched on

1) Water contains, a variable quantity of limestone and mineral salts of which quantities vary according

to geographical locations thus varying its conductivity values. Relevant variations of the conductivity

of the water compared to those prefixed by the factory could slightly influence the residual humidity

of the laundry at the end of the cycle. Your dryer allows you to regulate the sensitivity of the drying

sensor based on conductivity values of the water.

2) By default the warning LED is always on at the end of the drying cycle or during the cycle if the water

reservoir is full. When using an external drain for the condensed water warning can be offi

Installation

Transporting the appliance

Important! Only tip the appliance on its left

side to transport (see illustration), if it cannot

be transported in an upright position.

Warning! If the appliance was not

transported in an upright position, leave

it to stand for 12 hours before

connecting it to the electricity supply and

using it for the first time, so that the oil

can flow back to the compressor.

Otherwise the compressor could be

damaged.

Appliance positioning

• It is recommended that, for your conven-

ience, the machine is positioned close to

your washing machine.

• The tumble dryer must be installed in a

clean place, where dirt does not build up.

• Air must be able to circulate freely all round

the appliance. Do not obstruct the front

ventilation grille or the air intake grilles at

the back of the machine.

• To keep vibration and noise to a minimum

when the dryer is in use, it should be

placed on a firm, level surface.

• Once in its permanent operating position,

check that the dryer is absolutely level with

the aid of a spirit level. If it is not, raise or

lower the feet until it is.

• The feet must never be removed. Do not

restrict the floor clearance through deep-

pile carpets, strips of wood or similar. This

might cause heat built-up which would in-

terfere with the operation of the appliance.

Important!

• The hot air emitted by the tumble dryer can

reach temperatures of up to 60°C. The ap-

pliance must therefore not be installed on

floors which are not resistant to high tem-

peratures.

• When operating the tumble dryer, the

room temperature must not be lower than

+5°C and higher than +35°C, as it may af-

fect the performance of the appliance.

• Should the appliance be moved, it must be

transported vertically.

• The appliance must not be installed behind

the lockable door, a sliding door a door

with a hinge on the opposite side to that of

the appliance in such a way that a full

opening of the dryer is restricted.

Removing transport safety packaging

Caution!

Before use all parts of the transport packag-

ing must be removed.

1. Open loading door

2. Pull off adhesive strips from inside ma-

chine on top of drum.

3. Remove foil hose and polystyrene pad-

ding from the machine.

Electrical connection

Details on mains voltage, type of current and

the fuses required should be taken from the

type plate. The type plate is fitted near the

loading aperture (see “Product description”

chapter).

Warning! The manufacturer declines

any responsibility for damage or injury

through failure to comply with the above

safety precautions.

Should the appliance power supply ca-

ble need to be replaced, this must be

carried out by our Service Center.

Warning! The power supply cable must

be accessible after installing the

machine.

Door reversal

Warning! Before changing the door

stop, disconnect the mains plug.

Open loading door.

2. Unscrew hinge A from the front of the

machine and take off the loading door.

3. Remove cover plates B . To do this, in-

sert a thin screwdriver into the slots as

shown in the illustration, press down-

wards slightly and pry out the cover

plates.

4. Use an appropriate tool and exert pres-

sure to unfasten locking block C from the

snap-on fixture, take out and re-insert on

the other side having rotated the block

through 180°.

5. Unscrew hinge A from the loading door,

rotate through 180°, re-insert on the op-

posite side and screw down.

Re-insert cover plates B on the opposite

site having first rotated them through

180°.

Unscrew cover plates D from the front of

the machine, rotate through 180°, screw

on the opposite side.

8. Unscrew door lock E , push down slight-

ly and remove from the front of the ma-

chine.

Press snap-in button F in and down,

press cover down slightly and remove

from front of the machine.

10. Change door lock E over to the opposite

side, screw down the door interlock.

11. On the other side, insert cover F and al-

low snap-in button to lock into place.

12. Insert loading door and hinges into re-

cesses on the front of the machine and

screw down.

Note regarding contact protection: The

machine is only secure for operations again

once all plastic parts have been inserted.

Special accessories

• stack kit

Available from your Service Force Centre

or your specialist dealer

These intermediate installation kits can be

used to arrange the dryer and an washing

machine (60 cm wide, front loaded) as a

space-saving washer/dryer stack. The

washing machine is at the bottom and the

dryer is at the top.

Read carefully the instructions supplied

with the kit.

• drain kit

Available from your Service Force Centre

or your specialist dealer

Installation kit for direct draining of con-

densate into a basin, siphon, gully, etc.

The condensate tank then no longer has

to be drained, it must however remain in

its intended position in the machine.

Read carefully the instructions supplied

with the kit.

• pedestal with the drawer

Available from your Service Force Centre

or your specialist dealer

To situate the dryer in optimal high and

have some additional space to store (e.g.

laundry).

Read carefully the instructions supplied

with the kit.

Service

In the event of technical faults, please first

check whether you can remedy the problem

yourself with the help of the operating in-

structions - see chapter What to do if….

If you were not able to remedy the problem

yourself, please contact the Customer Care

Department or one of our service partners.

In order to be able to assist you quickly, we

require the following information:

– Model description

– Product number (PNC)

– Serial number (S No. is on rating plate stuck

to the product - to find it see chapter Product

description ))

– Type of fault

– Any error messages displayed by the ap-

pliance

So that you have the necessary reference

numbers from your appliance at hand, we

recommend that you write them in here:

Model description: ........................................

PNC: ........................................ S No: ........................................

La pagina sta caricando ...

Novamatic TW7757 Manuale utente

Marca: Novamatic

Modello: TW7757

Categoria: Asciugatrici

Tipo: Manuale utente

Scarica il pdf

rapporto

in altre lingue

English: Novamatic TW7757 User manual

Novamatic TW7757 Manuale utente

Novamatic TW7757 Manuale utente

in altre lingue

Altri documenti